E M C C o m p o n e n t s November 0 Common Mode Filters For automobile signal line ACT series ACT5B ACT5R ACT5L [8 inch]* (CAN-BUS) [8 inch] (FlexRay) [8 inch] (Ethernet) * Dimensions Code JIS[EIA]
(/) REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than months. Be sure to follow the storage conditions (Temperature: 5 to 0 C, Humidity: 0 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 50 C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. () Aerospace/Aviation equipment () Transportation equipment (electric trains, ships, etc.) () Medical equipment () Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (0) Electric heating apparatus, burning equipment () Disaster prevention/crime prevention equipment () Safety equipment () Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment.
(/) Common Mode Filters For automobile signal line Overview of the ACT Series Product compatible with RoHS directive Compatible with lead-free solders AEC-Q00 FEATURES Compatible with an operating temperature range of 0 to +50 C, so can be used for vehicle devices requiring compatibility with high temperatures. (ACT5B, ACT5R) When mounting, the terminal and winding tape splicing part do not fuse. ACT5R for FlexRay, which uses our unique technology, is a product that can achieve DCR < @ 5 deg. C by reducing the DC resistance while maintaining a high L-value of 00μH. ACT5L for Ethernet, which uses our unique technology, is a product that can realize higher-level Scd mode conversion characteristics while maintaining a high L-value of 00μH. APPLICATION ACT5B CAN-BUS, FAXs, modems, ISDNs, etc. ACT5R FlexRay system. ACT5L Ethernet system. PART NUMBER CONSTRUCTION ACT5B - 50 - P - TL Series name Inductance(typ.) (μh) Number of lines Packaging style Internal code ACT5B 0 P lines TL ø0mm reel ACT5R 0 ACT5L 50 5 0 00 0 00 OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Type Operating temperature Temperature range Storage temperature Package quantity Individual weight C C pieces/reel g ACT5B 0 to +50 0 to +50,500 0. ACT5R 0 to +50 0 to +50,500 0. ACT5L 0 to +05 0 to +05,500 0. The Storage temperature range is for after the circuit board is mounted. RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/
(/) Overview of the ACT Series RECOMMENDED REFLOW PROFILE Preheating Soldering Peak T Natural cooling T: Temperature T T t T T t t t: Time Preheating Soldering Peak Temp. Time Temp. Time Temp. Time T T t T t T t 50 C 80 C 60 to 0s 0 C 0s max. 5 C 5s
(5/) ACT series ACT5B Type SHAPE & DIMENSIONS.5±0. Marking.±0..8±0. 0.7±0. 0.65±0. RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM.6. No polarity. 5.9
(6/) ACT series ACT5B Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Common mode impedance ( ) [0MHz] min. typ. Common mode inductance(μh) +50/ 0% [00kHz] Stray inductance (μh)typ. [00kHz] DC resistance ( )max. Rated current (A)max. Insulation resistance (M )min. Rated voltage (V)max. Part No. 00 600 0.05 0.6 0.5 0 50 ACT5B-0-PTL 500 00 0.08.0 0. 0 50 ACT5B-0-PTL 000 800 5 0.5.0 0. 0 50 ACT5B-50-PTL 000 5800 00 0.0.0 0.5 0 50 ACT5B-0-PTL Measurement item Product No. Manufacturer Common mode impedance 99A Agilent Technologies Common mode inductance 9A Agilent Technologies DC resistance 8A Agilent Technologies Insulation resistance 9A Agilent Technologies IMPEDANCE VS. FREQUENCY CHARACTERISTICS 00000 0000 0 Common mode 50 Common mode 0 Common mode Impedance (Ω) 000 50 Differential mode 00 0 Common mode 0 Differential mode 0 Differential mode 0 Differential mode 0 0 00 000 Frequency (MHz) Product No. Manufacturer 99A Agilent Technologies
(7/) ACT series ACT5R Type SHAPE & DIMENSIONS.5±0. Marking.±0..8±0. 0.7±0. 0.65±0. RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM.6. No polarity. 5.9
(8/) ACT series ACT5R Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Common mode impedance ( ) [0MHz] min. typ. Common mode inductance(μh) +50/ 0% [00kHz] Stray inductance (μh)typ. [00kHz] DC resistance ( )max. Rated current (A)max. Insulation resistance (M )min. Rated voltage (V)max. Part No. 00 5500 00 0..5 0. 0 50 ACT5R-0-P-TL00 Measurement item Product No. Manufacturer Common mode impedance 99A Agilent Technologies Common mode inductance 9A Agilent Technologies DC resistance 8A Agilent Technologies Insulation resistance 9A Agilent Technologies IMPEDANCE VS. FREQUENCY CHARACTERISTICS 00000 0000 Impedance (Ω) 000 00 0 Common mode 0 0 Differential mode 0 00 000 Frequency (MHz) Product No. Manufacturer 99A Agilent Technologies
(9/) ACT series ACT5L Type SHAPE & DIMENSIONS.5±0. Marking.±0..8±0.5 (0.5) (0.65) (.) RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM 0.7..9 5.5 No polarity
(0/) ACT series ACT5L Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Common mode inductance (μh)typ. [00kHz] DC resistance ( )max. Rated current (ma)max. Insulation resistance (M )min. Rated voltage (V)max. Part No. 00.5 00 0 50 ACT5L-0-P-TL000 Measurement item Product No. Manufacturer Common mode inductance 9A Agilent Technologies DC resistance 8A Agilent Technologies Insulation resistance 9A Agilent Technologies IMPEDANCE VS. FREQUENCY CHARACTERISTICS 00000 0000 0 Common mode Impedance (Ω) 000 00 0 Differential mode 0 0 00 000 Frequency (MHz) Product No. Manufacturer 9A Agilent Technologies
(/) ACT series Packaging style REEL DIMENSIONS.0±0.5 E Type A W W N E ACT5B ø0±.5±0.5 7.5± 00± typ. ACT5R ø0±.5±0.5 7.5± 00± typ. ACT5L ø0±.5±0.5 7.5± 00± typ. N.0 A ø.0±0. ø.0±0.8 W W TAPE DIMENSIONS ød0 P P0 F E t B W A P K Type A B ød0 E F P0 P P W K t ACT5B.6±0..9±0..55±0.05.75±0. 5.5±0.05.0±0. 8.0±0..0±0.05.0±0..05±0. 0.±0.05 ACT5R.6±0..9±0..55±0.05.75±0. 5.5±0.05.0±0. 8.0±0..0±0.05.0±0..05±0. 0.±0.05 ACT5L.6±0..9±0..55±0.05.75±0. 5.5±0.05.0±0. 8.0±0..0±0.05.0±0..05±0. 0.±0.05 Blank Products Blank 60min. 00 to 500 Start End Drawing direction