MEASURING INSTRUMENT Capacitance Leakage Current / IR Meter Model IR 2689 Features Capacitance leakage current test function. Insulation resistance test function. Precise low current charge function (0.5mA±0.05mA). Large current (500mA) improves the charge speed of low voltage large capacitance. Continoues adjustment of test voltage (1V - 800V). Comparator function for sorting (PASS/FAIL). 10 groups of status can be saved. Real time large digital LCD display (240 x 64 dot matrix). RS 232 and Handler interface. Accessories : Standard 3 terminal test cable
IR 2689 Technical Specification Parameter Range Trigger mode Sorting Test voltage Voltage Accuracy Charge current Current Accuracy Test range LC & IR Auto, Hold. INT/MAN/EXT. High, Low, Pass with beeper alarm. 1.0V - 800V. ±0.5% set value + 0.2V. 100V, 0.5mA - 500mA. >100V, 0.5mA - Imax, Imax = 50W ±3% set value + 0.05mA. LC: 0.001µA - 20mA. IR: 0.01kΩ - 99.99GΩ. Charge time upper limit 0-999s. Test time Limit setting Operating Voltage Operating temperature Fast: 53ms, Med: 70ms, Slow:139ms. Test condition : Range is locked, trigger mode is EXT. LC- 0-999.999mA IR - 0-999.999GΩ. 198-242 VAC. 0 C - 40 C. Machine weight : 7.2 kgs Approx. Note: We reserve the right to modify above specifications at any time. Please confirm your specification before ordering.
MEASURING INSTRUMENT Automatic Rated Voltage CAP & TAN D Measuring Set with Power Supply & Jigs Features Microprocessor Controlled Measurement. Precise measurements with electronic tunning of current comparator. Digital numeric setting of test parameter with memory. High resolution 7 segment LED display for test Voltage as well as Capacitance deviation range of 20% or 40% for value and 2% or 20% for Tan D with measurement of absolute capacitance value in mfd. Capacitance Range fro 0.01mfd to 1100mfd. Digital Handler interface helps for table top or automatic test system usage. Combination of high accuracy with high speed measurement. Compact and ergonomic design minimizing floor space and better handling Space.
ARVCT Technical Specification Test Voltage Capacitnce Range Maximum voltage for capacitance range Test Resolution Reading Accuracy Memory Measuring Time (Electronic Balance) Pass or Fail Judgement Output Memory 50 V - 1000V AC @ 50Hz / 60Hz in steps of 50V steps. Digital Display 0.01-1100mfd 100V - 0.01 to 1100mfd 200V - 0.01 to 600mfd 400V - 0.01 to 210mfd 600V - 0.01 to 300mfd 1000V - 0.01 to 120mfd A). Capacitance A). Tan D 20% Range : ±0.00% - ±20.00% 2% Range : ±0.000% - ±2.000% 40% Range : ±00.00% - ±40.00% 20% Range : ±0.000% - ±20.00% B). Capacitance B). Tan D 20% Range : ±0.2% + 2 digits 2% Range : ±(0.01% + 2 digit) 40% Range : ±0.5% + 2 digit 20% Range : ±(0.05% + 2 digit) 9 set of front panel settings in memory With in 1 sec. (Front panel / Remote measurement) Digital standard / Limit setting through front panel Output Signal for Pass, High, Low & Tan D Reject. Open Collector (Output Current 8mA Max.) Power Supply (Optional) Power Supply Output Current for power supply Voltage Selection Dimension Weight Indicators Voltage Selection 440 V AC, 2 ph, 50Hz. Upto 1kV in 50V steps Upto 32A for 5 sec, 16A continuous duty max. Course 200V Steps, Fine 50V Steps 540 mm (W) x 540 mm (L) x 1200 mm (H) 300 Kg. (Approximately) For Power ON, Voltage ON & Over Load. 1000V - 0.01 to 120mfd only Jigs & Fixture (Optional) Jigs & Fixture Contacts Discharge of Test Capacitor Air Pressure Pneumatically operated jigs through a foot switch. Phosphor Bronze Contacts Built in adjustable delay by flow control for discharging capacitor through Test Transformer. 6 bars. Machine weight : 100 Kgs.(Approx.) Floor space : 430 mmx 380mm x 199mm (W x L x H). Interface (Optional) : Digital Handler Interface is available for triggering and Binning Note: We reserve the right to modify above specifications at any time. Please confirm your specification before ordering.
MEASURING INSTRUMENT Automatic Charge Discharge Tester (5000Amps) Features Manual Loading of the Test Capacitor to the Test fixture. Capacitance Range from 1mfd to 500mfd. Adjustable Test Voltage through Salzer Switch provided on Front Panel. Adjustable Current From 100A to 10, 000A. Adjustable Charge Discharge Time through Text Panel interfaced to PLC. Monitoring of charge discharge slopes through oscilloscopes output. Voltage accuracy ±3% Current Accuracy ±10% Discharge Through Vacuum Circuit Breaker. Accessories : Standard 2 terminal test cable
Technical Specification Test Voltage Voltage Indication Current Test Capacitance Range Charge Time Discharge Time No. Of Test Cycles Digital Counter Indicators 600 to 1500 V DC. 3½ digit Digital Voltmeter. 100 to 10,000 A. 1 to 500 MFD. Adjustable 1 to 5 Sec. Adjustable 0.3 to 1Sec. Programmable On Digital Counter up to 10,000. 6 Digit Up & Down Counter. Power ON & OFF, Test Over & Alarm. Power Supply Air Supply Floor space Machine weight : 230V AC, 50Hz, 1 ph. : 6 bars, Consumption 4 cfm. : 450 x 465 x 266 mm (W x L x H). : 18Kgs.(Approx.) Note: We reserve the right to modify above specifications at any time. Please confirm your specification before ordering.
MEASURING INSTRUMENT Auto Discharge Device Tester Model AD 56 Features AD - 56, is used to test the discharging efficiency of the power factor capacitors discharging devices. Digital Voltmeter for test voltage indication. Digital programmable timer to indicate charging & discharging rate. System is totally automatic. Safety features are incorporated (Charge and discharge Current Limiting). Accept and reject indicators Short circuit and overload protection. Selectable Charging rate. Accessories : Standard 2 terminal test cable
AD 56 Technical Specification Capacitor Range Test Voltage Timer Charging Rate Switch Sorting Function Selection Switch Limit setting Knobs Indicator 1 to 25 KVAR (Can be extending upto 50KVAR) Continuously adjustable 100 to 1000 V DC. Digital timer up to 60 Sec. Charging rate up to 8x Accept & Reject. Set zero, Low limit and High Limit. Independent Set Zero, Low limit and High Limit. Self illuminating Power On switch. AC Fuse 3A. Power supply : 230 V AC, ± 10%, 50 Hz, 500 W Floor space : 435 x 400 x 285 mm. (L x W x H) Machine weight : 30 Kg. (Approximately) Note: We reserve the right to modify above specifications at any time. Please confirm your specification before ordering.
MEASURING INSTRUMENT AC/DC Break Down and IR tester Model BD 9201 Features AC/DC Breakdown tester & insulation resistance tester 240 x 64 dot matrix graphic LCD display Fast discharge and arc detection function. Programmable Charging time, measuring time and discharge time for different load Programmable DC break down voltage current judging time and waiting time. RS 232 and Handler interface. Accessories : Standard Voltage withstanding test rod Other accessories on request - Voltage withstanding test cable.
BD 9201 Technical Specification Output Voltage Current test range Output Voltage Resistance Test Range AC DC Voltage Adjustment AC DC Test Accuracy Discharge Function Break Down Voltage Test 0.05kV - 5kV ±(1% of reading + 5 digit) (50Hz, 60Hz optional) 0.05kV - 6kV ±(1% of reading + 5 digit) (1.0% + 10V) (rated power) 0.1mA - 20mA 0.01mA - 5mA ±(1% of reading + 5 digit) Discharge after test ends. Insulation Resistance Test 0.05kV - 1kV ±(1.5% of reading + 5V) 0.1MΩ - 10GΩ (Current Range within 10nA - 10mA) Resistance Test Accuracy 500V - 1000V 50V - 500V 1M Ω - 1GΩ ±(5% of reading + 5 digit) 1MΩ - 10GΩ ±(10% of reading + 5 digit) 0.1MΩ - 1GΩ ±(10% of reading + 5 digit) Discharge Function Measurement Range Voltage rise time Voltage fall time Voltage wait time Test time setting Standard AC DC Discharge after test ends. Arc Detection 1mA - 15mA 1mA - 5mA 0.1s - 999s 0.1s - 999s 0.1s - 999s(Only for DC) 0.3s - 999s Interface RS 232, Remote I/O, Scan, Handler Machine weight : 3.8Kgs.(Approx.) Note: We reserve the right to modify above specifications at any time. Please confirm your specification before ordering.
MEASURING INSTRUMENT LCR Meter Model LCRZ 2817B Features 10 Selectable typical frequencies (50Hz to 100kHz). Three different test levels (0.1Vrms, 0.3Vrms, 1.0Vrms) with continuous indication of the selected frequency, Test Voltage & Parameter. High accuracy,wide measurement range, Easy operation and Perfect functions. LCD display with white back light. Strong protection against electrical shock of charged capacitor. 2 selectable source impedance 30Ω/100Ω, easy to be compatible with other LCR meters. Key lock function. Out put impedance : 30Ω, 100Ω. Accessories - Standard 4 terminal Kelvin test cable. Other accessories on request - 4 terminal test fixture, 4 terminal Kelvin test clip leads and Gilded shorting plate (As shown below).
LCRZ 2817B Technical Specification Measurement Parameter Basic Accuracy Equivalent Circuit Range Mode Trigger Mode Measurement Speed Calibration Function Delay Time Measurement Terminal Display Mode Frequency Test Level Comparator Function Memory Output Impedance Interface Operating Voltage Operating Frequency [Z] C, L, X, B, R, G, D, Q, q (deg), q (rad) 0.1%. Series, Parallel. Auto, Hold Manual. Internal, Manual, External & BUS Fast 20,Medium 8, Slow 2 (times/sec)( 1kHZ). Open and Short Sweep Correction 0-60s, with step of 1ms. 5 Terminal. Direct, Delta & %. 50Hz,60Hz,100Hz,120Hz,1kHz,10kHz,20kHz,40kHz,50kHz,100Hz. 0.1Vrms,0.3Vrms & 1Vrms. 5 Bin sorting (3 Pass bin, 1NG bin) and 1 AUX bin. 10 sets of test parameters saved / loaded. 30Ω, 100Ω. RS-232C, Handler, GPIB (Optional). 198-242V AC. 47.5Hz - 52.5Hz Measurement Range Z, R, X Capacitance (C) Inductance (L) Tan Delta (D) Q q (DEG) q (RAD) % 0.0001Ω - 99.999MΩ. 0.001pf - 9999.9µf. 0.001µH - 99.999kH. 0.0001-9.9999. 0.0001-99999. -179.999-179.999. -3.14159-3.14159. 999.999% - 999.999%. Machine weight : 4Kgs.(Approx.) Note: We reserve the right to modify above specifications at any time. Please confirm your specification before ordering.
MEASURING INSTRUMENT LCR Meter Model LCRZ 2816B Features 37 Selectable typical frequencies (50Hz to 200kHz). Programmable single voltage level from 10mVrms to 2Vrms. High accuracy,wide measurement range, Easy operation and Perfect functions. 240 x 64 dot matrix graphics LCD display, 6 digit resolution. Strong protection against electrical shock of charged capacitor. 2 selectable source impedance 30Ω/100Ω, easy to be compatible with other LCR meters. Key lock function. Accessories - Standard 4 terminal Kelvin test cable. Other accessories on request - 4 terminal test fixture, 4 terminal Kelvin test clip leads and Gilded shorting plate (As shown below).
LCRZ 2816B Technical Specification Measurement Parameter Basic Accuracy Equivalent Circuit Range Mode Trigger Mode Measurement Speed Calibration Function Delay Time Measurement Terminal Display Mode Frequency Test Level Comparator Function Memory Output Impedance Interface Operating Voltage Operating Frequency [Z] C,L,X,B,R,G,D, Q, q (deg), q (rad) 0.1%. Series, Parallel. Auto, Hold. Internal, Manual & External. Fast 30,Medium 10, Slow 1 (Meas/sec)( 1kHZ). Open and Short 0-60s, with step of 1ms. 5 Terminal. Direct, ΔABS, Δ%, V/I(V/I Monitor), Bin No & Bin Counter 50Hz,60Hz,100Hz,120Hz,150Hz,200Hz,250Hz,300Hz,400Hz,500Hz, 600Hz,800Hz,1kHz,2kHz,2.5kHz 3kHz,4kHz,5kHz,6kHz,8kHz,10kHz, 12kHz,15kHz,20kHz,25kHz,30kHz,40kHz,50kHz,60kHz,80kHz, 100Hz,20kHz,150kHz,200kHz. 10mVrms-2Vrms,10mv steps. Comparator Function 12 Batches can be stored or recalled. 30Ω, 100Ω. RS-232C, Handler. 198-242V AC. 47.5Hz - 52.5Hz Measurement Range Z, R, X Capacitance (C) Inductance (L) Tan Delta (D) G,B Q q (DEG) q (RAD) % 0.00001Ω - 99.9999MΩ. 0.00001pf - 999.999mf. 0.00001µH - 9.99999kH. 0.00001-9.99999. 0.00001μS - 999.999S. 0.00001-99999.9. -179.999-179.999. -3.14159-3.14159. 999.999% - 999.999%. Machine weight Floor space : 4Kgs.(Approx.) : 350 (W) x 340 (L) x 110 (H) mm. Note: We reserve the right to modify above specifications at any time. Please confirm your specification before ordering.
MEASURING INSTRUMENT Portable LCR Meter Features Three selectable typical frequencies (100Hz, 120Hz & 1 KHz) Portable LCR meter with large LCD display Auto power off function Battery & external power supply Open & short correction Accessories - Standard 4-terminal Kelvin test cable
Technical Specification Measurement Parameter Basic Accuracy Equivalent Circuit Range Mode Measurement Speed Calibration Function Measurement Terminal Display Mode Frequency C-D, R-Q, L-Q, Z -Q 0.3%. Series, Parallel. Auto, Hold. ~3meas/sec Open/Short Correction. 5 Terminal. Direct 100Hz,120Hz & 1kHz Measurement Range Z, R Capacitance (C) @ 100Hz & 120Hz. Capacitance (C) @ 1kHz. Inductance (L) @ 100Hz & 120Hz Inductance (L) @ 1kHz Tan Delta (D) Q 0.0001Ω - 9.999MΩ. 1pf - 9999µf. 0.1pf - 999.9µf. 1µH - 9999H. 0.1µH - 999.9H. 0.0001-9.999. 0.0001-9999. Power supply Machine weight : Battery 1604, 9V or Adaptor 12V DC, 150mA : 400 Kg. (Approximately) Note: We reserve the right to modify above specifications at any time. Please confirm your specification before ordering.
MEASURING INSTRUMENT Capacitance Meter Model CR 2012 Features Four Selectable typical frequencies (100Hz to 10kHz). Three different test levels (0.1V, 0.3V, 1.0V) with continuous indication of the selected frequency, Test voltage & Parameter. High accuracy, Wide measurement range, Easy operation and Perfect functions. Programable 5 bin sorting facility. Strong protection against electrical shock of charged capacitor. LCD display for measurement results and test conditions. Out put impedances : 30Ω, 100Ω. Accessories - Standard 4 terminal Kelvin test cable. Other accessories on request - 4 terminal test fixture, 4 terminal Kelvin test clip leads and Gilded shorting plate (As shown below).
CR 2012 Technical Specification Primary Measurement Parameter Secondary Measurement Parameter Basic Accuracy Equivalent Circuit Range Mode Trigger Mode Measurement Speed Calibration Function Measurement Terminal Display Mode Frequency Test Level Interface Operating Frequency R & Z Capacitance (C) Tan Delta (D) Q C: Capacitance R: Resistance Z :Absolute value of impedance D: Dissipation θ: Phase anglex : Reactance ESR: Series equivalent resistance 0.1%. Series, Parallel. Auto, Hold. Internal, Manual, External, DUT & BUS. FAST : 20 meas/sec, MED : 7meas/sec, SLOW : 3 meas/sec Open/Short Sweep Correction. 4 Terminal. Measurement Range Direct, Absolute, %. 100Hz,120Hz,1kHz,10kHz. 0.1Vrms,0.3Vrms & 1Vrms. RS-232C, Handler. 47.5Hz - 63Hz. 0.1mΩ to 99.9MΩ 100Hz,120Hz - 1pF to 99999μF 1kHz - 0.1pF to 99999μF 10kHz - 0.01pF to 99999μF 0.0001 to 9.9999 0.0001 to 99999 Dimension Machine weight : 310mm(W) x 105mm (H) x 295mm (L) : 3.5 Kgs.(Approx.) Note: We reserve the right to modify above specifications at any time. Please confirm your specification before ordering.
MEASURING INSTRUMENT Precision LCR Meter Model LCR 2013 Features High precision, Wide measurement range with six digit resolution, Easy operation and Perfect functions. Can be used for incoming inspection of components, quality control and laboratory use with wide frequency from 20Hz to 200KHz. Four different parameters displayed simultaneously with flexible and comfirtable combination. Both AC & DC parameters can be measured simultaneously without any interference. Powerful list sweep function, wherein different parameters and excitation sources can be mixed sweep test and displayed. Strong protection against electrical shock of charged capacitor. Built in continuous DC biasl -5V to +5V Independent and ow noise DC source : -10V to +10V continuously adjustable with resolution 2.5mV. RS232C, GPIB, Handler interfaces and perfect command system. Accessories - Standard 4 terminal Kelvin test cable. Other accessories on request - 4 terminal test fixture, 4 terminal Kelvin test clip leads and Gilded shorting plate (As shown below).
LCR 2013 Technical Specification Measurement Parameter Basic Accuracy Equivalent Circuit Range Mode Trigger Mode Measurement Speed Calibration Function List Sweep Graphics Scanning Function Frequency Test Level Comparator Z, C, L, R, X, Y, B, G, D, Q, q, DCR 0.05%. Series, Parallel. Auto, Hold. Internal, Manual, DUT, External & BUS Fast 65, Medium 10, Slow 5 (meas/sec). Open/Short/Load, Full Frequency Correction, 64 points frequency correction. 20 points frequency, level, DC bias, DC source Frequency, Level, Bias voltage/current, DC source 20 Hz to 200KHz with resolution 1mHz. 10mV to 2V with resolution 1mV, 100mA to 100mA with resolution 1mA 10 bins, BIN0-BIN9, NG, AUX. PASS/FAIL LED display. Internal DC Bias Voltage Mode Current Mode -5V - +5V, Resolution - 1mV -50mA - 50mA, Resolution - 20mA Output DC Source Interface Operating Voltage Operating Frequency -10V - +10V, Resolution - 2.5mV RS-232C/USB HOST/Handler 99V - 242V AC. 47.5Hz - 63Hz. Measurement Range Z, R, X Y, G, B Capacitance (C) Inductance (L) Tan Delta (D) q (Deg) q (Rad) % Q DCR 0.01mΩ - 99.9999MΩ. 0.0001mS - 999.999S. 0.00001pf - 99.9999mf. 0.00001µH - 99.9999kH. 0.00001-9.99999. -179.9-179.9-3.14159-3.14159-999.99% - 999.99%. 0.01-99999.9. 1mΩ - 99.9999MΩ Dimension : 350 x 120 x 360 mm. (W x H x D) Machine weight : 3.5 Kg. (Approximately) Note: We reserve the right to modify above specifications at any time. Please confirm your specification before ordering.