Assembly Instructions ITEM#:L-GZ076PST-1A-4 Vineyard Gazebo IMPORTANT: Please read and follow all safety statements, warnings, assembly instructions, use & care directions, before attempting to assemble IMPORTANT: 1. When installing and assembling your gazebo, it is recommended that 4 or more adults are involved. 2. Do not use the unit during an electrical storm, as there is a remote chance of getting struck by lightning. 3. Do not climb on top of the gazebo. Falling off the gazebo can result in serious injury, possibly even death. 4. Do not leave the gazebo assembled when there is a risk of high wind, as possible damage will occur to the structure. 5. Never barbecue under this gazebo or use lanterns that contain open flames. 6. This package contains small items and plastic bags that should be kept away from children. 7. Ensure that all connectors & poles are firmly secured fully in position. It is important to do so before use so as to avoid collapsing or damage to the item, which could result in injury. 1
Hardware Pack AA M5 15 mm Screw 56 PCS BB M5 Flat Washer 56 PCS CC M6 Nut 6 PCS DD M6 30 mm Screw 8 PCS EE M6 Flat washer 22 PCS FF Plastic Washer 4 PCS W Stake 8 PCS GG Plastic Tie 48 PCS HH M 6 45 mm Screw 8 PCS WW M6 Wrench 1 PC Spare Hardware AA M5 15 mm Screw 4 PCS BB M5 Flat Washer 4 PCS CC M6 Nut 2 PCS DD M6 30 mm Screw 2 PCS EE M6 Flat Washer 2 PCS GG Plastic Tie 4 PCS HH M6 45 mm Screw 2 PCS 2
Parts List Pole 1 A1 2 Pole 2 A2 1 Pole 3 A3 1 Pole 4 A4 1 Pole 5 A5 1 Fence B 4 Screen C 6 Corner connector D 6 Top pole E 6 Center fitting with hook F 1 Glass side bar top G 1 Side bar top support (preassembled on the side bar top G) H 2 Peg fitting 1 I 2 Peg fitting 2 J 2 Peg fitting 3 K 2 Canopy S 1 Top canopy S1 1 Bug netting S2 1 3
Step.1: Insert Fence (B) into Pole (A4 or A2,A1,A3,A5), then fix Fence (B) by pulling it down (Fig.1A). Assemble Fence (B) and pole with.screw (HH) and Flat washer (EE) (Fig.1B). Step.2: Use Screw (AA) and Flat washer (BB) to connect Peg fitting (K) to Fence (B) and Pole (A4 or A2) (Fig.2). Assemble Peg fitting (J) to Fence (B) and Pole (A1) in the same way. Step.3: Use Screw (AA) and Flat washer (BB) to assemble Peg Fitting (I) and Fence (B) and Pole (A3 or A5) (Fig.3). 4
Step.4: Use Screw (AA) and Flat washer (BB) to fix the Corner connector (D) to the poles (Fig4-1). Use Screw (AA) and Flat washer (BB) to assemble the Screen (C) and pole (Fig4-2). Use Screw (AA) and Flat washer (BB) to fix the Corner connector (D) and the Screen (C) (Fig4-3) Step.5: Use Screw (DD), Flat washer Fig.5-2 E D (EE) and Nut (CC) to joint Top pole (E) and Center connector (F) (Fig 5-1). And then lift the assembled top frame to insert the other end of the Top pole (E) into the Corner Fig.5-1 connector (D) (Fig.5-2) *After steps above, use screwdriver and wrench to tighten all the hardware, but not too tight. Fig.6-1 Fig.6-2 S1 S Fig.6-3 Step.6: Assemble the canopy (S) on top frame (do not tighten) (Fig6-1). Fully assemble top canopy (S1) on small top frame, (Fig.6-2). Tie the bug netting around the top canopy to canopy and then fully stretch canopy (S) and fix it to the end of corner connectors (D) (Fig 6-3) 5
Step. 7: Use Screw (DD), Flat washer (EE) and Plastic washer (FF) to fix the Glass side bar top (G) to Pole (A3 and A4) and then use Wrench (WW) to tighten the screw, but not too tight so that the glass bar top can flip smoothly. Insert the pin on the pole into the hole at the end of the bar top support (H) and then put the dowel attached to the little chain into the pin on the pole to set up the side bar top (Fig 7). When not in use, the side bar top support (H) can go separately with the poles and the top can stand vertically. Fig.8-1 Step 8:Use stake (W) to fix the gazebo on ground (Fig. 8-1). Lastly use the Plastic ties (GG) to fix the Bug netting (S2) to the screen (Fig. 8-2), and tie the bug netting to the poles. Fig.8-2 Now the gazebo is ready for use. USE & CARE: 1. This Gazebo is not a permanent structure and should be disassembled & stored away after use. 2. Do not repack your gazebo until completely dry. 3. This Gazebo must be assembled by Four adults or more. 4. This Gazebo must not be left erect in windy conditions. 5. Loading limit of the hook is 45 lbs 6. Loading limit of the ring is 25 lbs 7. Loading limit of the glass side bar top is 33 lbs. 6
WARNINGS: 1. Assembly Instructions must be followed. 2. Pegs supplied must be used to hold this gazebo in place when upright. 3. Warranty does not cover damage due to extreme weather conditions. 4. Do not use candles, matches or open flames of any kind in or near a tent. 5. Do not cook inside the tent. 6. Build campfires downwind and several meters away from a tent and be sure to fully extinguish campfires before leaving a campsite or before retiring for the night. 7. Exercise extreme caution when using fuel-powered lanterns or heaters inside a tent and use battery-operated lanterns whenever possible. 8. Do not refuel lamps, heaters or stoves inside a tent. 9. Extinguish or turn off all lanterns before going to sleep. 10.Do not smoke in a tent. 11.Do not store flammable liquids inside a tent 12. KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS TENT FABRIC. This tent is made of flame-resistant fabric. It is not fireproof. The fabric will burn if left in continuous contact with a flame source. 7