Technical Information TYRISTORS T3-3P from 35A to 700A Specifications Universal 3 Phase Thyristor Unit 55-77-03-6, March 0 GENERAL ESCRIPTION TYRISTORS T3-3P is a full digital and universal Thyristor unit based on a very powerful dedicated micro configurable via serial communication port for all inputs, firing modes, control modes and loads types. Suitable to drive resistive, inductive, transformer and complex loads requiring current limit and power control mode. Frontal Key Pad standard to configure all the internal functions and parameters. Four Analog output configuirable. Six igital input. Four realay output. Universal Input signal with automatic zero/span calibration. Universal Firing modes, customer configurable via Key Pad or communication port as Burst Firing and Phase Angle. Universal Feed back modes. Soft Start can be used in addition to Burst Firing and Phase Angle. Unbalanced load and eater Break Alarm. RS 85 port. Modbus protocol. Comply with EMC and * up to 500A. IP0 Protection. * cul approval up to 500A included.
TECNICAL SPECIFICATION Operating Temperature 0+0 C over this temperature see derating curve. Voltage Power supply 80V standard, 600V or 690V on request. Auxiliary Voltage Supply 90 65V, 0VA power consumption. Fan voltage supply: 30V ±5% as a standard and 0V on request. Analog Input Main reference, 0mA, 0 0V, 0KPOT, RS85 port. Analog Input Secondary reference, 0 0V, 0KPot. Analog Input 3 External Current Limit Set, via analog input 0-0V or KPot. Analog Ouput igital Input Relay Output Universal Firing Soft Start Control Mode eater Break Alarm Unbalanced load Communication Thermal protection Four Analog output (0 0mA or 0mA) for retransmitted of, Voltage or Power and current for each Phase. Six optoisalated digital input (/Vdc), for START, STOP, ENABLE, CALIBRATION, RESET ALARM and EXTERNAL ALARM. Three configurable relay output and one critical alarm. One of these firing modes can be configured Burst Firing BF, Single Cycles SC, Soft Start + Burst Firing S+BF; Soft Start + Phase Angle S+PA; elayed Triggering T. igital adjustable ramp rate. Voltage (V), Current (I), Power (VxI) and External feedback. Circuit microprocessor based to diagnose partial or total load failure and short circuit on Thyristors. This protection allow to have Multidrive working up to 0% of unbalance on one phase. RS85 Port. Modbus communication protocol 9600 or 900 bauds. Available on forced ventilated units. 0.8 0.6 0. 0. erating curve
EATER BREAK ALARM B ON FRONT CABINET BURST FIRING BF PASE ANGLE PA ELAYE TRIGGERING T C EASY C-KP = FE MINUTES TO SET AN CALIBRATE ALL TE UNITS FIEL BUS MOULE The eather Break circuit diagnostic partial or total load failure. It reads load resistance with an internal voltage transducer and current transformer to calcolate the resitance value V/I. The eather Break circuit is compensated for voltage fluctuation,infact a voltage variation has no influence on resistance value because V/I ratio remain constant. On this unit is possible to set the nominal resistance value and the alarm sensitivity. B alarm in addition diagnostic the thyristor in short circuit. A normaly open contact gives the alarm condition and an indication of the alarm type appears on display. This firing is performed digitally within the thyristor unit at zero volts, producing no EMC interference. Analogue input is necessary for BF and the number of complete cycles must be specified for 50% power demand. This value can be between and 55 complete cycles, determining the speed of firing. hen is specified, the firing mode becomes Single Cycle (SC). PA controls the power to the load by allowing the thyristor to conduct for part of the AC supply cycle only. The morepower required, the more the conduction angle is advanced until virtually the whole cycle is conducting for 00% power. The load power can be adjusted from 0 to 00% as a function of the analogue input signal, normally determined by a temperature controller or potentiometer, PA is normally used with inductive loads. Used to switch the primary coil of transformers when coupled with normal resistive loads (not cold resistance) on the secondary, T prevents the inrush current when zero voltage (ON-OFF) is used to switch the primary. The thyristor unit switches OFF when the load voltage is negative and switches ON only when positive with a pre-set delay for the first half cycle. This is a memory support tool that can be used by mantenance personnel on shop floor. The user can copy the configuration of one unit and paste it into another. C EASY is very simple with one push button to upload the configuration (Read and another to down load the stored configuration (rite) This tool can be used with our Remote service to mail the working configuration via internet. The C-KP is designed mounted on front cabinet and to be connected with all cd automation s Thyristor units via RS85. On front unit is possible to read parameters, power, current, reference and alarms. One of these variables can be selected and retransmitted via an isolated output ( 0mA or 0 0V) On front unit is available a connector to comunicate with PC. In addition are available Local/Remote, up and down and function command. C-RS Used to convert RS3 to RS. TU-RS85-PP Used to convert RS85 Modbus to Profibus P. TU-RS85-ET Used to convert RS85 Modbus to Ethernet. For more informations see "Field Bus Module" Bulletin. POER SCALING APPLICATIONS AN FOCUS ON: It's a scaling factor of the input command signal and limit the output of Thyristor unit. This parameter can be adjusted from to 99% via RS85 or by the front of the unit If this parameter is setted at 50% and the input signal is 00% the output become 50% This feature is very useful to reduce the power when a zone has been oversized or when a temperature controller gives same reference to more unit along a furnace. Imagine 3 zones with left and right one close to the doar where in acontinuos furnace the material come into and flow out.the profile of temperature along furnace is higher in central zone because there is less dispersion but if we scale its input we can have a flat profile. Infrared lamp Autoclaves Fournaces Chemical Petrochemical Climatic chambers Pharmaceutical 3
IRING CONNECTION TYRISTORS T3-3P from 35A to 700A TYRISTORS T3-3P NOTE () The user must provide for protection external electromagnetic circuit breaker or fuse isolator. () Use an appropriate external transformer to supply of the electronic board (see the identification label). (3) The coil contactor, the relays and other inductive loads must be equipped with opportune RC filter. () Before give the Start command supply the input of auxiliary voltage. TYRISTORS LOA TYPE Three phase transformer Cold Resistance Molibdenum, Tungstenum KantalSuper Platinum, Quartz lamp infrared short waveform Silicon carbide elements IMENSION AN FIXING OLES S3 6 mm. - 0 mm. - 70 mm. - kg. 8 5A 5A S 6 mm. - 50 mm. - 70 mm. - kg.,5 300A 600A S5 00 mm. - 50 mm. - 70 mm. - kg. 3 850A S 55 mm. - 580 mm. - 35 mm. - kg. 56 000A S5 55 mm. - 780 mm. - 35 mm. - kg. 77 00A S5 55 mm. - 780 mm. - 35 mm. - kg. 77 500A S6 780 mm. - 790 mm. - 533 mm. - kg. 850A S6 780 mm. - 790 mm. - 533 mm. - kg. 000A S7 890 mm. - 790 mm. - 58 mm. - kg. 7 00A S7 890 mm. - 790 mm. - 58 mm. - kg. 7 700A
OUTPUT FEATURES (POER EVICE) Current A Voltage range (V) Ripetitive peak reverse voltage (600V) (690V) Latching current (maeff) Max peak one cycle (0msec.) Leakage current (maeff) IT value for fusing tp=0msec. Frequency range (z) Power loss I=Inom () Isolation Voltage Vac 35A 330 690V 600 800 50 000 5 750 7 70 6 500 5A 330 690V 600 800 50 000 5 80 7 70 6 500 75A 330 690V 600 800 50 000 5 80 7 70 70 500 00A 330 690V 600 800 50 50 5 Fre300eF 7 70 360 500 5A 330 690V 600 800 50 000 5 900 7 70 50 500 50A 330 690V 600 800 50 000 5 900 7 70 50 500 55A 330 690V 600 800 300 800 5 08000 7 70 80 500 300A 330 690V 600 800 300 550 5 8000 7 70 080 500 350A 330 690V 600 800 00 7800 5 300000 7 70 60 500 00A 330 690V 600 800 00 8000 5 306000 7 70 0 500 50A 330 690V 600 800 000 7800 5 07000 7 70 60 500 500A 330 690V 600 800 000 7800 5 07000 7 70 800 500 600A 330 690V 600 800 000 7800 5 07000 7 70 60 500 850A 330 690V 600 800 000 7800 5 07000 7 70 3000 500 000A 330 600V 600 N.A. 700 500 300 78000 7 70 3300 500 00A 330 690V 600 800 700 600 300 306xE3 7 70 60 700 500A 330 600V 600 N.A. 700 600 300 306xE3 7 70 565 700 850A 330 690V 600 800 700 36000 300 680xE3 7 70 605 500 000A 330 600V 800 N.A. 700 36000 300 680xE3 7 70 6600 500 00A 330 690V 800 800 700 60000 300 80000xE3 7 70 8000 500 700A 330 600V 00 N.A. 700 60000 300 80000xE3 7 70 05 500 ORERING COES 3 5 6 7 7 8 9 0 3 5 6 TYRISTORS T3-3P T 3 -, 5, 6 escription code 35A 5A 75A 00A 5A 50A 5A 300A 350A 00A 50A 500A 600A 850A 000A 00A 500A 850A 000A 00A 700A Current LEGEN IF = Internal Fixed Fuse CT = Current Transformer B = eater Break Alarm Numeric code 0 0 3 5 0 0 5 0 0 7 5 0 0 0 0 5 0 5 0 0 5 0 3 0 0 0 3 5 0 0 0 0 0 5 0 0 5 0 0 0 6 0 0 0 8 5 0 0 0 0 () 0 0 5 0 0 () 8 5 0 0 0 0 () 0 0 7 0 0 () 7 Max Voltage 80V 600V 690V 6 7 8 Aux. Voltage supply 0V 30V 9 Input SSR 3:30V dc 0:0V :0mA 0KPot RS85 Note (): After 6th digit write current and voltage of load inside brackets Ex. (90A- 00V). This is to receive the Thyristor unit already tuned from oneywell. Note (): Rating not available at 690V. Note (3): In total are available Analog output. One dedicated to control mode and the other 3 for current on phases --3. Note (): cul approval up to 500A included. S V A K R 0 Firing Zero Crossing ZC Single Cycle SC Burst Firing BF Soft Start + Burst Firing S+BF elayed Triggering + Burst Firing T+BF Phase Angle PA Soft Start + Phase Angle S+PA Z C B J P Control Mode Open Loop Voltage Feed Back V Power Feed Back VxI Current Feed Back I External Feed Back 3 Fan Voltage Fan Voltage equal to Aux. Voltage 3 E 0 U I E Option (3) :0mA Retransmission 0:0V Retransmission A V Note Approvals CE EMC For European Market 0 cul For American Market up to 500A included L () 5 Manual None Italian Manual English Manual German Manual French Manual 0 3 6 Load type/connection elta Connection Star Connection Star Connection + Neutral 7 Transformer Load/ elta Connection 3 Transformer Load/ Star Connection Transformer Load/Star Connection + Neutral 5 Open delta 6 5
SALES AN SERVICE For application assistance, current specifications, pricing, or name of the nearest Authorized istributor, contact one of the offices below. ASIA PACIFIC EMEA NORT AMERICA SOUT AMERICA hfs-tac-support@honeywell.com Australia oneywell Limited Phone: +(6) 7-386 55 Fax: +(6) 7-380 68 Toll Free: 300-36-39-36 Toll Free Fax: 300-36-0-70 China - PRC - Shanghai oneywell China Inc. Phone: (86-) 557-568 Fax: (86-) 637-86 oneywell Process Solutions Phone: + 8000655 or + (0)065583 Fax: + (0) 3 65555 Email: (Sales) sc-cp-apps-salespa6@honeywell.com or hfs-tac-support@honeywell.com oneywell Process Solutions Phone: -800-3-9883 or -800-33-08 Email: (Sales) ask-ssc@honeywell.com or hfs-tac support@honeywell.com oneywell do Brasil & Cia Phone: +(55-) 766-900 Fax: +(55-) 766-905 Email: (Sales) ask-ssc@honeywell.com or hfs-tac-support@honeywell.com Singapore oneywell Pte Ltd. Phone: +(65) 6580 378 Fax: +(65) 65-3033 South Korea oneywell Korea Co Ltd. Phone: +(8) 799 6 Fax: +(8) 79 905 Specifications are subject to change without notice. For More Information Learn more about how oneywell s TYRISTORS T3-3P and how it can help improve plant performance. Visit our website www.honeywellprocess.com/ or contact your oneywell account manager. oneywell Process Solutions 860 est Rose Garden Lane Phoenix, Arizona 8507 Phone: -800-3-9883 or -800-33-08 www.honeywellprocess.com/ 55-77-03-6 March 0 0 oneywell International Inc. 6