LAD-TRS Series Mobile Ladder Stands with Straddle Base Instruction Manual

Rev..3.08 LAD-TRS, MANUAL Vestil Manufacturing Corp. 999 North Wayne Street, P.O. Box 507, Angola, IN 6703 Telephone: (60) 665-7586 -or- Toll Free (800) 38-0868 Fax: (60) 665-339 Web: www.vestilmfg.com Email: info@vestil.com LAD-TRS Series Mobile Ladder Stands with Straddle Base Instruction Manual Receiving instructions: After delivery, remove the packaging from the product. Inspect the product closely to determine whether it sustained damage during transport. If damage is discovered, record a complete description of it on the bill of lading. If the product is undamaged, discard the packaging. NOTE: The end-user is solely responsible for confirming that product design, installation, use, and maintenance comply with laws, regulations, codes, and mandatory standards applied where the product is used. Table of Contents Specifications...... Signal Words.... 3 Hazards of Improper Use.. 3 Exploded Parts Diagrams and Bills of Materials..... 7 Assembly Instructions...8 0 Using the Ladder... Inspections & Maintenance... Labeling Diagram...... Limited Warranty... Copyright 08 Vestil Manufacturing Co. Page of

Rev..3.08 LAD-TRS, MANUAL Specifications: Dimensions and other specifications for each standard LAD-TRS series ladder stands appear in the following diagrams and table. Model Number of steps A: Overall height B: Usable length C: Overall length D: Platform height Step angle Capacity Net Weight LAD-TRS-50--P 50 33 3 / 6 0 50 350 lb. 9 lb. LAD-TRS-50--G 50 33 3 / 6 0 50 350 lb. 93 lb. LAD-TRS-50-3-P 3 60 3 5 / 6 5 9 / 6 30 50 350 lb. 08 lb. LAD-TRS-50-3-G 3 60 3 5 / 6 5 9 / 6 30 50 350 lb. 0 lb. LAD-TRS-50--P 70 5 3 / 60 5 / 6 0 50 350 lb. 7 lb. LAD-TRS-50--G 70 5 3 / 60 5 / 6 0 50 350 lb. 8 lb. LAD-TRS-50-5-P 5 80 55 3 / 6 69 3 / 8 50 50 350 lb. 7 lb. LAD-TRS-50-5-G 5 80 50 55 / 50 50 350 lb. 9 lb. LAD-TRS-50-6-P 6 90 7 / 77 / 8 60 50 350 lb. 6 lb. LAD-TRS-50-6-G 6 90 7 / 77 / 8 60 50 350 lb. 66 lb. LAD-TRS-60--P 50 7 5 / 8 3 / 6 0 58 350 lb. 9 lb. LAD-TRS-60--G 50 7 5 / 8 3 / 6 0 58 350 lb. 93 lb. LAD-TRS-60-3-P 3 60 33 7 / 8 50 7 / 6 30 58 350 lb. 07 lb. LAD-TRS-60-3-G 3 60 33 7 / 8 50 7 / 6 30 58 350 lb. 09 lb. LAD-TRS-60--P 70 0 / 8 55 3 / 0 58 350 lb. 9 lb. LAD-TRS-60--G 70 0 / 8 55 3 / 0 58 350 lb. 30 lb. LAD-TRS-60-5-P 5 80 6 3 / 8 6 50 58 350 lb. 5 lb. LAD-TRS-60-5-G 5 80 6 3 / 8 6 50 58 350 lb. 7 lb. LAD-TRS-60-6-P 6 90 5 5 / 8 68 / 60 58 350 lb. 6 lb. LAD-TRS-60-6-G 6 90 5 5 / 8 68 / 60 58 350 lb. 6 lb. Copyright 08 Vestil Manufacturing Co. Page of

Rev..3.08 LAD-TRS, MANUAL Signal Words: This manual classifies personal injury risks and situations that could lead to property damage with SIGNAL WORDS. These signal words announce an associated safety message. The reader must understand that the signal word chosen indicates the seriousness of the described hazard. Identifies a hazardous situation which, if not avoided, WILL result in DEATH or SERIOUS INJURY. Use of this signal word is limited to the most extreme situations. Identifies a hazardous situation which, if not avoided, COULD result in DEATH or SERIOUS INJURY. Indicates a hazardous situation which, if not avoided, COULD result in MINOR or MODERATE injury. Identifies practices likely to result in product/property damage, such as operation that might damage the crane. Hazards of Improper Use: Vestil strives to identify all foreseeable hazards associated with the use of its ladders. However, no manual can address every possible risk. The most effective means for avoiding injury is to apply sound judgment whenever using this ladder. Read all of the instructions prior to using the ladder to familiarize yourself with assembly, use and maintenance practices. If this product is used improperly or carelessly, the user and/or bystanders might sustain serious personal injuries or could even be killed. ALWAYS use the product properly: Read and understand the entire manual before assembling, using or servicing the ladder. DO NOT exceed the rated load of the ladder. The total weight applied to the ladder (weight of the user plus tools, etc.) must not be greater than the rated load. DO NOT use the ladder on uneven or unstable surfaces. ONLY use the ladder on level, even surfaces Make sure that you will not contact overhead objects with either your body or with the ladder during use. Always unload the ladder before leaving it unattended. Remove foreign matter, like mud or grease, from your shoes before walking on the ladder. ALWAYS face the stairs and use the handrails while ascending and descending the ladder. DO NOT increase the height of the platform or of a step by standing on other objects placed on the ladder. Inspect the ladder as described in Inspections & Maintenance on p.. DO NOT use the ladder unless it is in normal condition. ONLY use manufacturer-approved replacement parts if repairs are necessary. DO NOT use the ladder if the caps on the legs are severely worn (see exploded parts diagrams on p. -7). Caps should prevent the ladder from sliding. If any of the caps is too worn to function properly, replace it before using the ladder again. ONLY use the ladder to access objects that you cannot otherwise reach. DO NOT use the ladder for any other purpose. For instance, DO NOT use the ladder as a storage rack or as a way to move people or material. Always unload the ladder before leaving it unattended. DO NOT lean or reach over the sides of the ladder. Position the ladder as close to the work as possible. DO NOT attempt to move the ladder while someone is using it. DO NOT use the ladder to transport people or objects. DO NOT remove or obscure any label. Each label must be readable, undamaged, and present in the appropriate location (see Labeling diagram on p. ). DO NOT modify this ladder! Unauthorized modifications automatically void the limited warranty (see p. ) and might make the ladder unsafe to use. This product must be properly maintained to function properly. (See Inspections & Maintenance, p. ). Keep the ladder clean & dry. Periodically check the ladder frame. The ladder should be solid, square, and free of rust and corrosion. Lubricate the wheel bolts whenever necessary for the wheels to rotate freely. The ladder stand is designed for both indoor and outdoor use. However, it should be stored indoors when not in use. Copyright 08 Vestil Manufacturing Co. Page 3 of

Rev..3.08 LAD-TRS, MANUAL Exploded Parts Diagram and Bill of Materials: LAD-TRS-50--P & LAD-TRS-50--G LAD-TRS-50-3-P & LAD-TRS-50-3-G LAD-TRS-50--P & LAD-TRS-50--G *NOTE: Diagram shows LAD-TRS-50--G. Item Part no. Description Qty. Item Part no. Description Qty. Weldment, step frame: 0 99-0-07 Square cap, x Duro. -67-0 LAD-TRS-50--P 99-0-08 Square cap, / x / -67-097 LAD-TRS-50--G 99-05-05 plastic plug (black) -67-03 LAD-TRS-50-3-P -67-098 LAD-TRS-50-3-G -67-0 LAD-TRS-50--P 3 055 Hex bolt, HHCS, 5 / 6-8UNC x -67-099 LAD-TRS-50--G -5-99 -5-300 -5-30 Weldment, back leg, 6 step: -step: LAD-TRS--P & -G 3-step: LAD-TRS-3-P & -G -step: LAD-TRS--P & -G 3-5-33 Weldment, frame, caster tilter -5-3 Weldment, frame, back platform 5-5-7-5- -5-3 Weldment, handrail, 50 6 step -step: LAD-TRS--P & -G 3-step: LAD-TRS-3-P & -G -step: LAD-TRS--P & -G 6 6-3-009 Wheel, PP-/.5-W 060 5 06 Hex bolt, gr. A, zinc plated, 5 / 6-8UNC x 3 / Hex bolt, #,HHCS, zinc plated, 5 / 6-8UNC x / Hex bolt, gr. A, zinc finish, 3 / 6 07 8-6x / 7 3 Hex bolt, gr. A, 3 / 8-6x / 8 33006 9 33008 0 336 7-0-06 Square cap, x, 60 Duro. 370 8-0-95-0-9-0-93 Frame, straddle support: LAD-TRS-50--P & -G LAD-TRS-50-3-P & -G LAD-TRS-50--P & -G 9-0-87 Frame, tube, back leg 370 Flat washer, zinc plated, USS, 5 / 6 Flat washer, low carbon, USS zinc plated, 3 / 8 Split lock washer, carbon steel, medium zinc finish, 3 / 8 Nylon insert lock nut, gr., zinc finish, 5 / 6-8 Nylon insert lock nut, gr., zinc finish, 3 / 8-6 3-00-06 Frame, tube, back leg Copyright 08 Vestil Manufacturing Co. Page of

Rev..3.08 LAD-TRS, MANUAL Exploded Parts Diagram & Bill of Materials: LAD-TRS-50-5-P & LAD-TRS-50-5-G LAD-TRS-50-6-P & LAD-TRS-50-6-G *NOTE: Diagram shows LAD-TRS-50-5-G. Item Part no. Description Qty. Item Part no. Description Qty. -67-05 -67-00 -67-06 -67-0 -5-30 -5-303 Weldment, step frame, 50 : LAD-TRS-50-5-P LAD-TRS-50-5-G LAD-TRS-50-6-P LAD-TRS-50-6-G Weldment, back leg, 6 step: 5-step: LAD-TRS-5-P & -G 6-step: LAD-TRS-6-P & -G 3-5-33 Weldment, frame, caster tilter -5-3 Weldment, frame, back platform 5-5- -5-5 Weldment, handrail, 50 6 step 5-step: LAD-TRS--P & -G 6-step: LAD-TRS-3-P & -G 6 6-3-009 Wheel, PP-/.5-W 7-0-06 Square cap, x, 60 Duro. Base support: 8-0-9 LAD-TRS-50-5-P & -G -0-38 LAD-TRS-50-6-P & -G 0 99-0-07 Square cap, x Duro. 99-0-08 Square cap, / x / 99-05-05 plastic plug (black) 3 055 Hex bolt, HHCS, 5 / 6-8UNCx 060 5 06 Hex bolt, gr. A, zinc plated, 5 / 6-8UNC x 3 / 8 Hex bolt, #,HHCS, zinc plated, 5 / 6-8UNC x / Hex bolt, gr. A, zinc finish, 3 / 6 07 8-6x / 7 3 Hex bolt, gr. A, 3 / 8-6x / 8 33006 9 33008 0 336 370 9-0-87 Frame, tube, back leg 370 Flat washer, zinc plated, USS, 5 / 6 Flat washer, low carbon, USS zinc plated, 3 / 8 Split lock washer, carbon steel, medium zinc finish, 3 / 8 Nylon insert lock nut, gr., zinc finish, 5 / 6-8 Nylon insert lock nut, gr., zinc finish, 3 / 8-6 3-00-06 Ladder tool tray, 3 9 / 6 6 Copyright 08 Vestil Manufacturing Co. Page 5 of

Rev..3.08 LAD-TRS, MANUAL Exploded Parts Diagram and Bill of Materials: LAD-TRS-60--P & LAD-TRS-60--G LAD-TRS-60-3-P & LAD-TRS-60-3-G *NOTE: Diagram shows LAD-TRS-60--G. Item Part no. Description Qty. Item Part no. Description Qty. -67-053 -67-05 -67-05 -67-05 -5-99 -5-300 Weldment, step frame: LAD-TRS-60--P LAD-TRS-60--G LAD-TRS-60-3-P LAD-TRS-60-3-G Weldment, back leg, 6 step: -step: LAD-TRS-60--P & -G 3-step: LAD-TRS-60-3-P & -G 3-5-33 Weldment, frame, caster tilter -5-3 Weldment, frame, back platform 0 99-0-07 Square cap, x Duro. 99-0-08 Square cap, / x / 99-05-05 plastic plug (black) 3 055 Hex bolt, HHCS, 5 / 6-8UNC x 060 5 06 Hex bolt, gr. A, zinc plated, 5 / 6-8UNC x 3 / Hex bolt, #,HHCS, zinc plated, 5 / 6-8UNC x / 6 07 Hex bolt, gr. A, zinc finish, 3 / 8-6x / 7 3 Hex bolt, gr. A, 3 / 8-6x / 8 33006 Flat washer, zinc plated, USS, 5 / 6 5-5-059-5-038 Weldment, handrail, 58 6 step -step: LAD-TRS-60--P & -G 3-step: LAD-TRS-60-3-P & -G 6 6-3-009 Wheel, PP-/.5-W 7-0-06 Square cap, x, 60 Duro. 9 33008 0 336 Flat washer, low carbon, USS zinc plated, 3 / 8 Split lock washer, carbon steel, medium zinc finish, 3 / 8 8-0-95-0-9 Base support: LAD-TRS-60--P & -G LAD-TRS-60-3-P & -G 370 Nylon insert lock nut, gr., zinc finish, 5 / 6-8 9-0-87 Frame, tube, back leg 370 Nylon insert lock nut, gr., zinc finish, 3 / 8-6 3-00-06 Ladder tool tray, 3 9 / 6 Copyright 08 Vestil Manufacturing Co. Page 6 of

Exploded Parts Diagram & Bill of Materials: LAD-TRS-60--P & LAD-TRS-60--G LAD-TRS-60-5-P & LAD-TRS-60-5-G LAD-TRS-60-6-P & LAD-TRS-60-6-G *NOTE: Diagram shows LAD-TRS-60-5-G. Rev..3.08 LAD-TRS, MANUAL Item Part no. Description Qty. Item Part no. Description Qty. Weldment, step frame, 58 : 0 99-0-07 Square cap, x Duro. -67-08 LAD-TRN-60--P 99-0-08 Square cap, / x / -67-08 LAD-TRN-60--G 99-05-05 plastic plug (black) -67-083 LAD-TRN-60-5-P -67-08 LAD-TRN-60-5-G -67-085 LAD-TRN-60-6-P 3 055 Hex bolt, HHCS, 5 / 6-8UNCx -67-086 LAD-TRN-60-6-G -5-30 -5-30 -5-303 Weldment, back leg, 6 step: -step: LAD-TRN-60--P & -G 5-step: LAD-TRN-60-5-P & -G 6-step: LAD-TRN-60-6-P & -G 3-5-33 Weldment, frame, caster tilter -5-3 Weldment, frame, back platform 5-5-0-5-0-5-03 Weldment, handrail, 58 6 step -step: LAD-TRN-60--P & -G 5-step: LAD-TRN-60-5-P & -G 6-step: LAD-TRN-60-6-P & -G 6 6-3-009 Wheel, PP-/.5-W 7-0-06 Square cap, x, 60 Duro. 8-0-33-0-33-0-30 Base support: LAD-TRN-60--P & -G LAD-TRN-60-5-P & -G LAD-TRN-60-6-P & -G 9-0-87 Frame, tube, back leg 060 5 06 Hex bolt, gr. A, zinc plated, 5 / 6-8UNC x 3 / Hex bolt, #,HHCS, zinc plated, 5 / 6-8UNC x / Hex bolt, gr. A, zinc finish, 3 / 6 07 8-6x / 7 3 Hex bolt, gr. A, 3 / 8-6x / 8 33006 9 33008 0 336 370 370 8 Flat washer, zinc plated, USS, 5 / 6 Flat washer, low carbon, USS zinc plated, 3 / 8 Split lock washer, carbon steel, medium zinc finish, 3 / 8 Nylon insert lock nut, gr., zinc finish, 5 / 6-8 Nylon insert lock nut, gr., zinc finish, 3 / 8-6 6 Copyright 08 Vestil Manufacturing Co. Page 7 of

Rev..3.08 LAD-TRS, MANUAL Assembly Instructions: Improper assembly might make the ladder unsafe to use. Visually inspect all ladder components prior to assembly. Look at each part of the ladder immediately after you receive the package from the shipper. Look for damage that might have occurred during shipping. DO NOT assemble or use the ladder stand if you notice any damage to one or more of the steps or to any other structural element (step weldment, back leg weldment, base supports, and handrails) of the ladder. Using the ladder stand despite weakness of a frame member could result in serious personal injuries. DO NOT assemble the ladder by yourself. At least people are needed for assembly. Read the entire instruction manual before assembling this ladder. DO NOT use the ladder if a wheel is damaged. Damaged wheels might cause the ladder to wobble or tip when used. The following tools are necessary to assemble the ladder:. crescent wrenches ( 5 / 6 and 3 / 8 ). Rubber mallet NOTE: Numbers in the diagrams and in parentheses () correspond to part numbers in the exploded views on pages -7. Step : Fasten the back leg tubes (-0-87) to the back leg weldment with bolts (06) and lock nuts (370). Then, attach the back leg weldment to the stair frame weldment with 5 / 6 in. hardware. Be sure to orient the back leg weldment as shown below (support tabs should face inwards). Wall Back leg weldment Brace tab Stair frame weldment 370 Back leg tube 06 370 060 Step : Fasten the vertical braces to the brace tabs. Brace tabs are located on the underside of the platform and on the back leg weldment. Fasten braces to the tabs with 5 / 6 8 hardware as shown. First slide a flat washer (33006) onto a bolt (055) and insert the bolt through the tab and the bolt hole in the brace. Secure bolts with lock nuts (370). Finger-tighten the connections. Ladder assembly Vertical brace 370 055 Brace tab 33006 Cross brace Brace tab 370 Copyright 08 Vestil Manufacturing Co. Page 8 of

Rev..3.08 LAD-TRS, MANUAL Step 3: Install the plugs, caps, and wheels. a) Install the plastic plugs and square caps in the leg tubes. First, press the in. plastic plug into the leg tubes. Then, press the square caps over the plugs and onto the ends of the legs. If necessary, use a rubber mallet to gently tap the plugs and caps into place. b) Press a plug into each end of the cross brace. Step : Fasten the wheel brackets (-5-33; caster tilter frames in exploded views) to the ladder assembly with 5 / 6-8 x 3 / bolts (060) and lock nuts (370). Attach the wheels (6-3-009) to the wheel bracket as indicated in the diagrams below. Ladder assembly Cross brace Insert plug 99-05-05.5 black plastic plug -0-06 060 & 370 6-3-009 x square cap 99-0-07 black plastic plug 99-05-05.5 x.5 square cap 99-0-08-5-33 3 + 370 Step 5: Attach the handrails to the side rails of the ladder assembly with 5 / 6 8 x 3 / bolts (060) and 5 / 6 8 lock nuts (370). 060 Handrail 370 Copyright 08 Vestil Manufacturing Co. Page 9 of

Rev..3.08 LAD-TRS, MANUAL Step 6: Attach the platform bar to the bar tabs using the hardware shown in the diagram. Bar tab Platform bar -5-3 Bolt 07 Lock washer 336 Flat washer 33008 Side rail Step 7: Attach the tool tray to the handrails using brackets (-06-096), 5 / 6 8 x 3 / bolts (060) and corresponding 5 / 6 lock washers (336), flat washers (33006), and lock nuts (370). First, install the tray brackets as shown in diagram 7a. Next, align the bolt holes in the sides of the tray with the bolts and insert the bolts. Slide a flat washer (33006) followed by a lock washer (3360) onto each bolt. Secure each bolt with a lock nut (360). 7a: Attach tray brackets to handrails [NOTE: Insert bolts A and B on opposite sides of the bar tabs.] B A A B Tray bracket Flat washer 7b: Attach tray Secure each bolt on the inside of the tray with a flat washer, lock washer, and lock nut Copyright 08 Vestil Manufacturing Co. Page 0 of

Rev..3.08 LAD-TRS, MANUAL Using the ladder: Before climbing the ladder, stand on the bottom step and confirm that the caps solidly contact the ground. The rubber caps on the bottoms of the legs should prevent movement. Face the ladder and grasp the handrails while ascending and descending the steps. Do not lean against the handrails or the platform chain. To move the ladder, stand in front of the ladder, grasp the handrails, and rotate the ladder towards you until both wheels contact the ground and are able to roll. Push the ladder to the necessary location. Ladders with more steps are heavier and therefore require more effort to manipulate. Inspections & Maintenance: Inspect the entire structure before putting the ladder into service. Make a written record that describes the condition and appearance of the steps, handrails, wheels, (leg) caps, braces, back leg weldment, platform bar, and fasteners (bolts, nuts, etc.). Include the locations of labels (see Labeling diagram below).this record establishes normal condition of the ladder. Compare your observations from future inspections to the written record to determine whether the ladder is in normal condition. Do not use the ladder unless it is in normal condition. Regular inspections at least once per month inspect the following items. Replace all parts that are damaged before using the ladder again. DO NOT continue to use the ladder if damage cannot be repaired. Handrails and platform bar: Inspect both handrails. Confirm that they are solidly fastened to the steps. Each handrail should be rigid and undamaged. Examine the platform and platform bar. Confirm that the bar is securely fastened to the handrails. Tighten nuts and bolts, if necessary. Back leg weldment, wheel brackets (caster tilter frames in exploded parts diagrams, pages -7) and wheels: Make sure that the back leg weldment is not bent, twisted, etc. Wheels must not be severely worn otherwise they will not roll smoothly. Examine the wheel brackets and hardware for damage. Tighten nuts and bolts. Frame members (step weldment, back leg weldment, braces, handrails) and all fasteners (bolts, nuts, pins): Inspect each frame member for damage like excessive wear, bends, and cracks. All frame pieces should be square, rigid, and free of rust and corrosion. Remove rust with steel wool or a metal bristle brush and apply touch-up paint to the affected area. Check the areas where frame members are bolted together. Check the areas around bolt holes for cracks, elongated bolt holes, etc. Square (rubber) caps: Check the caps for cracks and excessive or uneven wear. If a cap requires replacement, install replacement caps before returning the ladder to service. Maintenance: Clean the ladder to remove dirt and grime, especially from step surfaces. Lubricate bolts when necessary for the wheels to rotate freely. Apply touchup paint wherever the finish is damaged. A B C Labeling diagram: The ladder should be labeled with labels A-D. Replace any label that is damaged, missing, or not easily readable (e.g. faded). DO NOT use the ladder unless all labels are in place and in normal condition. A: Label 70 (on nosing of a step or platform) B: Label 79A (on nosing of a step) D C: Label 87 (on nosing of a step) D: Label 8 (on nosing of a step) NOTE: Label locations vary from the diagram for ladders with fewer steps. Include label locations in your written record (see Inspections & Maintenance above.) Copyright 08 Vestil Manufacturing Co. Page of

Rev..3.08 LAD-TRS, MANUAL LIMITED WARRANTY Vestil Manufacturing Corporation ( Vestil ) warrants this Semi-Automatic Strapping Machine, model S-00 to be free of defects in material and workmanship during the warranty period. Our warranty obligation is to provide a replacement for a defective original part if the part is covered by the warranty, after we receive a proper request from the warrantee (you) for warranty service. Who may request service? Only a warrantee may request service. You are a warrantee if you purchased the product from Vestil or from an authorized distributor AND Vestil has been fully paid. What is an original part? An original part is a part used to make the product as shipped to the warrantee. What is a proper request? A request for warranty service is proper if Vestil receives: ) a photocopy of the Customer Invoice that displays the shipping date; AND ) a written request for warranty service including your name and phone number. Send requests by any of the following methods: Mail Fax Email Vestil Manufacturing Corporation (60) 665-339 info@vestil.com 999 North Wayne Street, PO Box 507 Phone Angola, IN 6703 (60) 665-7586 In the written request, list the parts believed to be defective and include the address where replacements should be delivered. What is covered under the warranty? After Vestil receives your request for warranty service, an authorized representative will contact you to determine whether your claim is covered by the warranty. Before providing warranty service, Vestil may require you to send the entire product, or just the defective part or parts, to its facility in Angola, IN. The warranty covers defects in the following original dynamic components: motors, hydraulic pumps, electronic controllers, switches and cylinders. It also covers defects in original parts that wear under normal usage conditions ( wearing parts ), such as bearings, hoses, wheels, seals, brushes, and batteries. How long is the warranty period? The warranty period for original dynamic components is 90 days. For wearing parts, the warranty period is 90 days. The warranty periods begin on the date when Vestil ships the product to the warrantee. If the product was purchased from an authorized distributor, the periods begin when the distributor ships the product. Vestil may, at its sole discretion, extend the warranty periods for products shipped from authorized distributors by up to 30 days to account for shipping time. If a defective part is covered by the warranty, what will Vestil do to correct the problem? Vestil will provide an appropriate replacement for any covered part. An authorized representative of Vestil will contact you to discuss your claim. What is not covered by the warranty?. Labor;. Freight; 3. Occurrence of any of the following, which automatically voids the warranty: Product misuse; Negligent operation or repair; Corrosion or use in corrosive conditions; Inadequate or improper maintenance; Damage sustained during shipping; Accidents involving the product; Unauthorized modifications: DO NOT modify the product IN ANY WAY without first receiving written authorization from Vestil. Modification(s) might make the product unsafe to use or might cause excessive and/or abnormal wear. Do any other warranties apply to the product? Vestil Manufacturing Corp. makes no other express warranties. All implied warranties are disclaimed to the extent allowed by law. Any implied warranty not disclaimed is limited in scope to t Copyright 08 Vestil Manufacturing Co. Page of