MATERIAL AND EQUIPMENT STANDARD FOR METRIC TYPE FASTENERS (SCREWS, BOLTS, STUDS, NUTS AND WASHERS) ORIGINAL EDITION DEC. 1997 This Standard is the property of Iranian Ministry of Petroleum. All rights are reserved to the owner. Neither whole nor any part of this document may be disclosed to any third party, reproduced, stored in any retrieval system or transmitted in any form or by any means without the prior written consent of the Iranian Ministry of Petroleum.
CONTENTS : PAGE No. 1. SCOPE.... REFERENCES.... DEFINITIONS AND TERMINOLOGY... 6. UNITS... 10. SPECIFIC REQUIREMENTS... 10.1 General Requirements... 10. Metallurgical and Requirements... 1. Specific Requirements of s... 1. Specific Requirements for Screws.... Specific Requirements for Bolts... 7.6 Specific Requirements for Studs....7 Specific Requirements for Nuts... 6.8 Specific Requirements for Washers... 60 6. MARKING... 71 7. DOCUMENTS... 77 8. TESTS... 77 9. CONFLICTING REQUIREMENTS... 78 10. PACKAGING... 78 11. SHIPMENT... 78 APPENDICES APPENDIX A DATA SHEET FOR FASTENERS... 79 1
1. SCOPE This Standard gives the minimum requirements of metric fasteners (screw threads, screws, bolts, nuts and washers) which are used in oil industries and their dimensions are in SI.. REFERENCES Throughout this Standard, the following standards and codes are referred to. The editions of these standards that are in effect at the time of publication of this Standard shall, to be extent specified herein, form a part of this Standard, the applicability of changes in standards and codes that occur after the date of this Standard shall be mutually agreed upon by the Company and the Vendor. ISO (INTERNATIONAL ORGANIZATION FOR STANDARDIZATION) ISO 68, 197 "ISO General Purpose Screw s-basic Profile" ISO, 198 "Fasteners-Bolts, Screws, Studs and Nuts Symbols and Designations of Dimensions" ISO 61, 197 "ISO General Purpose Metric Screw s-general Plan" ISO 6, 197 "ISO General Purpose Metric Screw s-selected Sizes for Screws, Bolts and Nuts" ISO 88, 1988 "ISO System of Limits and Fits" Parts 1, ISO 7, 1978 "ISO Metric Screw s-basic Dimensions" ISO 89, " Properties of Fasteners" Parts 1,, and 6 ISO 96 "ISO General Purpose Metric Screw s- " Parts 1, and ISO 107, 198 "Slotted Cheese Head Screws-Product Grade A" ISO 16, 1988 "Metallic Coatings-Electrodeposited Coatings of Nickel Plus Chromium and of Copper Plus Nickel Plus Chromium" ISO 18, 1988 "Metallic Coatings-Electrodeposited Coatings of Nickel" ISO 178, 198 "Tapping Screws s" ISO 179, 198 "Hexagon Head Tapping Screws" ISO 181, 198 "Slotted Pan Head Tapping Screws" ISO 18, 198 "Slotted Countersunk (Flat) Head Tapping Screws (Common Head Style)" ISO 18, 198 "Slotted Raised Countersunk (Oval) Head Tapping Screws (Common Head Style)" ISO/R 101, 1970 "ISO Miniature Screw s" ISO 10, 1978 "ISO General Purpose Metric Screw s-gauging" ISO 180, 198 "Slotted Pan Head Screws-Product Grade A" ISO 1891, 1979 "Bolts, Screws, Nuts and Accessories-Terminology and Nomenclature" ISO 009, 198 "Slotted Countersunk Head Screws (Common Head Style)- Product Grade A" ISO 010, 198 "Slotted Raised Countersunk Head Screws (Common Head Style) Product Grade A"
ISO 081, 1986 "Metallic Coatings-Electroplated Coatings of Zinc on Iron or Steel" ISO 70, 197 "Head Treated Steel Tapping Screws- Properties" ISO 901, 1977 "ISO Metric Trapezoidal Screw s-basic Profile and Maximum Material Profiles" ISO 90, 1977 "ISO Metric Trapezoidal Screw -General Plan" ISO 90, 1977 "ISO Metric Trapezoidal Screw s " ISO 90, 1977 "ISO Metric Trapezoidal Screw s-basic Dimensions" ISO 69, 1988 "Fasteners-Acceptance Inspection" ISO 06, 1979 "Corrosion-Resistant Stainless Steel Fasteners-Specifications" ISO 01, 1988 "Hexagon Head Bolts-Product Grade A and B" ISO 01, 1979 "Hexagon Head Bolts-Product Grade B-Reduced Shank (Shank Diameter=Pitch Diameter)" ISO 016, 1988 "Hexagon Head Bolts-Product Grade C" ISO 017, 1988 "Hexagon Head Screws-Product Grade A and B" ISO 018, 1988 "Hexagon Head Screws- Product Grade C" ISO 06, 1977 "Hexagon Socket Set Screws With Flat Point" ISO 07, 1977 "Hexagon Socket Set Screws With Cone Point" ISO 08, 1977 "Hexagon Socket Set Screws with Dog Point" ISO 09, 1977 "Hexagon Socket Set Screws With Cup Point" ISO 0, 1986 "Hexagon Nuts, Style 1-Product Grades A and B" ISO 0, 1979 "Hexagon Nuts, Style -Product Grades A and B" ISO 0, 1986 "Hexagon Nuts-Product Grade C" ISO 0, 1986 "Hexagon Thin Nuts (Chamfered) - Product Grades A and B" ISO 06, 1979 "Hexagon Thin Nuts - Product Grade B (Unchamfered)" ISO 0, 1989 "ed Components-Electroplated Coatings" ISO 161, 198 "Hexagon Nuts With Flange-Product Grade A" ISO 166, 1979 "Hexagon Nuts for Fine Mechanics Product Grade F" ISO 79/1, 1978 " for Fasteners-Part 1-Bolts, Screws and Nuts With Diameters Between 1.6 mm (Inclusive) and 10 mm (Inclusive) and Product Grade A, B and C" ISO 79/, 1979 " for Fasteners - Part Bolts, Screws and Nuts with Diameter From 1 up to mm (Inclusive) and Product Grade F for Fine Mechanics" ISO 76, 1977 "Hexagon Socket Head Cap Screws-Product Grade A" ISO 766, 198 "Slotted Set Screws With Flat Point" ISO 08, 198 "Cylindrical Screw s-vocabulary" ISO 617-1, 1988 "Fasteners-Surface Discontinuities- Part 1: Bolts, Screws and Studs for General Requirements" ISO 617-, 1988 "Fasteners-Surface Discontinuities- Part : Bolts, Screws and Studs for Special Requirements" ISO 700, 198 "Prevailing Torque Type Hexagon Nuts (With Non-Metallic Insert) Style 1 - Property Classes,8 and 10" ISO 701, 198 "Prevailing Torque Type Hexagon Nuts (With Non-Metallic Insert),
Style - Property Classes 9 and 1" ISO 70, 198 "Prevailing Torque Type All-Metal Hexagon Nuts, Style Property Classes,8,10 and 1" ISO 70, 198 "Prevailing Torque Type Hexagon Nuts (With Non-Metallic Insert)" ISO 70, 198 "Prevailing Torque Type All-Metal Hexagon Nuts With Flange" ISO 70, 198 "Cross Recessed Pan Head Screws-Product Grade A" ISO 706, 198 "Cross Recessed Countersunk Flat Head Screws (Common Head Style) Product Grade A and Property Class.8 Only" ISO 709, 198 "Cross Recessed Pan Head Tapping Screws" ISO 700, 198 "Cross Recessed Countersunk (Flat) Head Tapping Screws (Common Head Style)" ISO 7089, 198 "Plain Washers - Normal Series - Product Grade A" ISO 7090, 198 "Plain Washers, Chamfered - Normal Series-Product Grade A" ISO 7091, 198 "Plain Washers-Normal Series Product Grade C" ISO 709, 198 "Plain Washers-Small Series Product Grade A" ISO 778, 198 "Fasteners-Bolts, Screws and Studs-Split Pin Holes and Wire Holes" ISO 779, 198 "Hexagon Socket Head Shoulder Screws" ISO 780, 198 "Hexagon Socket Button Head Screws-Metric Series" ISO 711, 198 "Hexagon Bolts for High-Strength Structural Bolting With Large Width Across Flats ( Lengths According to ISO 888)- Product Grade C Property Classes 8.8 and 10.9" ISO 71, 198 ISO 71, 198 ISO 71, 198 ISO 717, 198 ISO 7, 198 ISO 7, 198 ISO 76, 198 ISO 7719, 198 ISO 867, 1988 ISO 867, 1988 ISO 87, 1988 ISO 8676, 1988 "Hexagon Bolts for High-Strength Structural Bolting With Large Width Across Flats (Short Length) - Product Grade C- Property Class 8.8 and 10.9" "Hexagon Nuts for Structural Boltings, Style 1 Hot-Dip Galvanized (Over Size Tapped) - Product Grades A and B- Property Classes, 6 and 8" "Hexagon Nuts for Structural Bolting With Large Width Across Flats, Style 1- Product Grade B- Property Class 10" "Hexagon Nuts for Structural Bolting-Style, Hot-Dip Galvanized (Oversize Tapped)-Product Grade A- Property Class 9" "Slotted Set Screws With Cone Point" "Slotted Set Screws With Long Dog Point" "Slotted Set screws With Cup Point" "Prevailing Torque Type All-Metal Hexagon Nuts, Style 1- Property Class, 8 and 10" "Hexagon Nuts, Style 1, With Metric Fine Pitch - Product Grades A and B" "Hexagon Nuts - Style, With Metric Fine Pitch - Product Grades A and B" "Hexagon Thin Nuts With Metric Fine Pitch - Product Grades A and B" "Hexagon Head Screws With Metric Fine Pitch - Product Grades A and B"
ISO 8677, 1986 "Cup Head Square Neck Bolts With Large Head- Product Grade C" DIN (DEUTSCHES INSTITUTE FUR NORMUNG) DIN 9 197 "Tab Washers With Long Tab" DIN 18 1987 "Curved and Wave Spring Lock Washers" DIN 17 1987 "Curved and Wave Spring Washers" DIN 67-197 "Round Screw with Clearance and Steep Flank with Pitch 7 mm, Limiting Dimensions of Screw s and Allowances Permissible Deviations and Permissible Wear of Screw Gage" DIN 67-10 1988 "Fasteners; Technical Delivery Conditions, Hot Dip Galvanized Parts" DIN 198 "External Tab Washers (Locking Tab Washers)" DIN 6 "Tab Washers With Long and Short Tab at Right Angles" DIN 78 198 "Square Head Bolts With Collar" DIN 79 198 "Square Head Bolts With Short Dog Point" DIN 80 198 "Square Head Bolts With Collar and Oval Half Dog Point" DIN 6 1986 "Slotted Round Nuts" DIN 8 1986 "Round Nuts With Set Pin Holes in Side" DIN 7 198 "Square Nuts; Product Grade C" DIN 61 198 "Hexagon Head Set Screws With Small Hexagon and Full Dog Point" DIN 6 1987 "Square Thin Nuts; Product Grade B" DIN 6 198 "Hexagon Head Set Screws With Small Hexagon and Coned Half Dog Point" DIN 609 198 "Hexagon Fit Bolts With Long ed Dog Point" DIN 610 198 "Hexagon Fit Bolts With Short ed Dog Point" DIN 98 198 "Square Weld Nuts" DIN 99 1987 "Hexagon Weld Nuts" DIN 9 1987 "Hexagon Slotted Nuts and Castle Nuts With Part 1 Metric Coarse and Fine Pitch ; Product Grades A and B" DIN 9 1987 "Hexagon Slotted Nuts With Metric Coarse Part Pitch ; Product Grade C" DIN 6796 1987 "Conical Spring Washers for Bolted Connections" DIN 6797 1971 "Toothed Lock Washers" DIN 6798 1971 "Serrated Lock Washers" DIN 690 197 "Curved Spring Washers for Screw Assemblies" DIN 690 197 "Spring Washers for Screw Assemblies" DIN 6906 197 "Lock Washers for Screw Assemblies" DIN 691 198 "Hexagon Socket Thin Head Cap Screws with Pilot Recess for Wrench" DIN 691 1987 "Spring Lock Washers With Safety Ring" DIN 691 1979 "Hexagon Bolts With Large Width Across"
DIN 6916 1979 DIN 6917 1979 DIN 798 198 "Washers for High-Tensile Bolting in Steel Structures" "Washers, Square, for High-Tensile Bolting of I Sections in Steel" "Hexagon Socket Thin Head Cap Screws". DEFINITIONS AND TERMINOLOGY Terms and definitions given below apply to this Standard..1 Terms and definitions cited in ISO 08 and ISO 1891. 6
. Terms and Nomenclatures as Hereunder..1 Shape of heads 7
.. Driving features.. Form of shank 8
.. Nomenclature of nuts 9
.. Nomenclature of washers. UNITS This Standard is based on International System of Units (SI), except where otherwise specified.. SPECIFIC REQUIREMENTS.1 General Requirements.1.1 Products shall have intact surfaces and edges and shall be free of any burr which influences 10
the performance of the product or would be a safety hazard when handled. Unless otherwise specified limits for surface discontinuities of bolts, screws and studs shall conform with ISO 617-1. Trimming burrs beyond the bearing face of bolts, screws, nut, studs and washers is not permissible. Center holes for bolts and screws are permissible, unless otherwise specified. The finish (surface) of the products shall be; - As processed for steel products not quenched and tempered; - In general, black oxide for quenched and tempered steel products; - Plain for products made of stainless steel or nonferrous metal. Bolts, screws, studs and nuts shall be delivered in a clean condition and lightly oiled..1. General dimensions of ends of metric threads for external threaded products are given in Table 1. Fig. 1 gives an illustration of different forms and symbols of different parts of these forms. 11
ENDS OF PARTS WITH EXTERNAL METRIC THREADS Fig. 1 Note: 1) The angle applies only to the portion of the point below the root diameter of the thread. 1
TABLE 1 - GENERAL DIMENSIONS OF ENDS OF METRIC THREADS FOR EXTERNAL THREADED PRODUCTS THREAD DIAMETER d 1 1. 1. 1.6 1.8... 1. 6 7 8 10 1 1 16 18 0 7 0 6 9 8 dp h 1 0. 0.6 0.7 0.8 0.9 1 1. 1..... 7 8. 10 1 1 1 17 18 1 6 8 0 8 d t 1) h 16 0.1 0.1 0.1 0.16 0.18 0. 0. 0. 0. 0. 0. 0. 0. 1.. 6 6 8 8 10 10 1 1 1 1 16 d z h 1 --- -- 0.7 0.8 0.9 1 1.1 1. 1. 1.7.. 6 7 8. 10 11 1 1 16 -- -- -- -- -- -- -- -- -- z 1 + IT 1 0 --- --- 0. 0. 0. 0. 0. 0.6 0.7 0.88 1 1.1 1. 1. 1.7.... 6 6.7 7. 8. 9 9.7 10. 11. 1 1 z + IT 1 0 --- --- 0.7 0.8 0.9 1 1.1 1. 1. 1.7... 6 7 8 9 10 11 1 1. 1 16. 18 19. 1. 6 1) M no flat part on the cone required; the point may be slightly rounded. Notes: 1) For tolerance values see ISO 79. ) For indicated notations see Fig 1..1. Dimensions of split pin holes and wire holes of external threaded products "if any" shall conform with ISO 778.. Metallurgical and Requirements..1 Metallurgical and mechanical properties and chemical composition limits of fasteners made of carbon steel and alloy steel "according to their property class" if not otherwise specified in datasheet and or pertinent workpiece requirement, shall comply with ISO 898... Composition range of corrosion resistant stainless steel fasteners for different grades of austenitic, martensitic and ferritic groups shall comply with Table of ISO 06... properties of corrosion resistant stainless steel fasteners like as tensile strength, stress, hardness and extension for bolts, screws and studs and proof load stress for nuts up to and including M9 shall comply with Tables and of ISO 06... Breaking torque of corrosion resistant stainless steel screws of M and smaller shall comply 1
with Table of ISO 06... properties of fasteners of non-ferrous metal shall conform with ISO 889...6 properties of Heat-treated steel tapping screws shall comply with ISO 70...7 Electroplated coating properties of threaded components shall comply with ISO 0...8 Compliance of properties shall be verified by the procedures denoted in the above mentioned standards.. Specific Requirements of s..1 Specification for general purpose metric screw threads..1.1 Basic profile The basic profile shall be as Fig.. D d D d D 1 d 1 H p BASIC PROFILE OF GENERAL PURPOSE METRIC SCREW THREADS Fig. = basic major diameter of internal thread (nominal diameter) = basic major diameter of external thread (nominal diameter) = basic pitch diameter of internal thread = basic pitch diameter of external thread = basic minor diameter of internal thread = basic minor diameter of external thread = height of fundamental triangle = pitch 1
The values of D, d, D 1 and d 1 have been calculated from the following formulas and rounded, in the next coming tables, to the third decimal place: D =D H=D 0.69 P 8 d =d H = D 0.69 P 8 D 1 = D- H =D-1.08 P 8 d 1 = d H = D 1.08 P 8..1. Dimensions Dimensions of different parts shall conform with Table, additionally the height of the fundamental triangle of thread shall comply with the below equation: H = / P = 0.866 0P TABLE - DIMENSIONS OF GENERAL PURPOSE METRIC SCREW THREADS NOMINAL DIAMETER = MAJOR DIAMETER D, d 1. 1.6 1.8..... 6 PITCH p 0. 0. 0. 0. 0. 0. 0. 0. 0. 0. 0. 0. 0. 0. 0.6 0. 0.7 0. 0.7 0. 0.8 0. 0. 1 0.7 PITCH DIAMETER D, d 1.0 1.70 1.7 1.70 1.7 1.670 1.70 1.88 1.907.08.07.7.67.77.110.7..67.01.17.80.67.17.0.1 MINOR DIAMETER D 1, d 1 1.07 1.18 1.1 1.8 1.1 1.8 1.67 1.79 1.71 1.99.01.11.9.61.80.11..9.688.99.1.9.99.917.188 APPLICATION CLASS Coarse Fine Coarse Fine Coarse Fine Coarse Fine Coarse Fine Coarse Fine Coarse Fine Coarse Fine Coarse Fine Coarse Fine Coarse Fine Fine Coarse Fine (to be continued) 1
NOMINAL DIAMETER = MAJOR DIAMETER D, d 7 8 9 10 1 1 16 18 0 6 7 0 6 9 8 6 60 6 68 PITCH P 1 0.7 1. 1 1. 1 1. 1. 1.7 1. 1. 1.. 1.. 1.. 1. 1....... 6 6 TABLE (continued) PITCH DIAMETER D, d 6.0 6.1 7.188 7.0 8.188 8.0 9.06 9.188 10.86 11.188 1.701 1.06 1.701 1.06 16.76 17.06 18.76 19.06 0.76 1.06.01.701.06.01.701 7.77 8.701 0.77 1.701.0.701 6.0 7.701 9.077.077.7 8.7.8 6.8 60.10 6.10 MINOR DIAMETER D 1, d 1.917 6.188 6.67 6.917 7.67 7.917 8.76 8.67 10.106 10.67 11.8 1.76 1.8 1.76 1.9 16.76 17.9 18.76 19.9 0.76 0.7 1.8.76.7.8 6.11 7.8 9.11 0.8 1.670.8.670 6.8 7.19 0.19.87 7.87 0.06.06 7.0 61.0 APPLICATION CLASS Coarse Fine Coarse Fine Coarse Fine Coarse Fine Coarse Fine Coarse Fine Coarse Fine Coarse Fine Coarse Fine Coarse Fine Coarse Fine Fine Coarse Fine Coarse Fine Coarse Fine Coarse Fine Coarse Fine Coarse Coarse Coarse Coarse Coarse Coarse Coarse Coarse Note: Dimensions other than those mentioned in Table "if required" will be selected from ISO 7...1...1..1 Tolerance grades For each of the two main elements, pitch diameter and crest diameter, a number of tolerance grades have been established. Related values for each grades are given in Tables,, and 6. In most cases the tolerance grade and tolerance position for two main element are the same which in such cases only one of them will be mentioned. As a general grade 6 shall be used for tolerance quality medium and normal length of thread engagement. The grades below 6 are intended for tolerance quality fine and/or short length of engagement. The grades above 6 are intended for tolerance quality of coarse thread and/or long length of thread engagement. Length of thread engagements are given in Table 8...1.. Tolerance positions for required workpieces shall be as below: - For nuts shall be either G with positive fundamental deviation or H with zero fundamental deviation. (see Table 7); Valves shall be in accordance with ISO 96/1. - for bolts shall be either e, f or g with negative fundamental deviation or h with zero fundamental deviation (see Table 7). Valves shall be in accordance with ISO 96/1. Note: Deviations for constructional threads in respect to different tolerance grades shall be in 16
accordance with ISO 96/ and more over for nut threads as well as bolt threads, the actual root contours shall not in any point transgress the basic profile. TABLE - MINOR DIAMETER TOLERANCES OF NUT THREAD (T D1 ) (CREST TOLERANCE OF NUT) PITCH P Mm μm 0. 6 0. 80 0. 90 0. 100 0. 11 0.6 1 0.7 10 0.7 10 0.8 160 1 190 1. 1 1. 6 1.7 6 00. 00. 0 7. 0 60. 600 6 60 TOLERANCE GRADES 6 μm --- 100 11 1 10 160 180 190 00 6 6 00 7 0 00 60 600 670 710 70 800 TABLE - MAJOR DIAMETER TOLERANCE OF BOLT THREAD (T d ) (CREST TOLERANCE OF BOLT) PITCH P Mm 0. 0. 0. 0. 0. 0.6 0.7 0.7 0.8 1 1. 1. 1.7.... 6 TOLERANCE GRADE (6) μm 67 8 9 100 106 1 10 10 10 180 1 6 6 80 7 7 00 0 60 600 17
TABLE - PITCH DIAMETER TOLERANCE OF NUT THREAD (T D ) BASIC MAJOR DIAMETER d PITCH TOLERANCE Over Up to and incl. P GRADE () mm mm mm μm 1..8.6 11...8.6 11.. 90 0. 0. 0. 0. 0. 0. 0. 0.6 0.7 0.7 0.8 0.7 1 1. 1. 1 1. 1. 1.7. 1 1... 1.. 6 --- 60 67 71 7 71 80 90 9 9 100 106 118 1 10 1 10 10 160 170 180 1 160 180 1 6 0 170 190 0 6 80 00 18
TABLE 6 - PITCH DIAMETER TOLERANCE OF BOLT THREAD (T d ) BASIC MAJOR DIAMETER d PITCH TOLERANCE Over Up to and incl. P GRADE () mm mm mm μm 1..8.6 11...8.6 11.. 90 0. 0. 0. 0. 0. 0. 0. 0.6 0.7 0.7 0.8 0.7 1 1. 1. 1 1. 1. 1.7. 1 1... 1.. 6 0 6 6 67 71 67 7 8 90 90 9 100 11 118 1 118 1 10 10 160 170 1 10 170 00 1 6 160 180 1 6 0 6 80 TABLE 7 - FUNDAMENTAL DEVIATIONS FOR NUT THREADS AND BOLT THREADS PITCH FUNDAMENTAL DEVIATION P NUT THREAD D, D 1 BOLT THREAD d, d G El e es f es g es mm μm μm μm μm 0. 0. 0. 0. 0. 0. 0. 0.6 0.7 0.7 0.8 1 1. 1. 1.7.... 6 +17 +18 +18 +19 +19 +0 +0 +1 + + + +6 +8 + + +8 + +8 + +60 +6 +71 +7 +80-0 - -6-6 -60-60 -6-67 -71-71 -80-8 -90-9 -100-106 -11-118 - - - -6-6 -8-8 -8-0 - - -8 - -8-6 -70-7 -80-8 -90-9 -17-18 -18-19 -19-0 -0-1 - - - -6-8 - - -8 - -8 - -60-6 -71-7 -80 19
TABLE 8 - LENGTHS OF THREAD ENGAGEMENT BASIC MAJOR DIAMETER d Over Up to and incl. 1..8.6 11.. 90 180.8.6 11.. 90 180 PITCH P 0. 0. 0. 0. 0. 0. 0. 0.6 0.7 0.7 0.8 0.7 1 1. 1. 1 1. 1. 1.7. 1 1... 1.. 6 6 6 LENGTH OF THREAD ENGAGEMENT S N L Up to and Over Up to and Over incl. incl. 0. 0. 1. 1. 0.6 0.6 1.9 1.9 0.8 0.8.6.6 1 1 1. 1..8.8 1 1 1. 1... 1.7 1.7 6 6.. 6.7 6.7.. 7. 7... 7.1 7.1 9 9 1 1 1 1.8.8 11 11.. 1 1.6.6 16 16 6 6 18 18 8 8 10 10 0 0 1 1 6. 6. 19 19 8. 8. 1 1 6 6 1 1 18 18 1 1 6 6 7. 7. 9. 9. 8 8 1 1 19 19 6 6 71 71 8 8 8 8 9 9 1 1 6 6 18 18 71 71 6 6 106 106 0 0 60 60 6 6 80 80 0 0 118 118 Note: The length of thread engagement is classified into one of three groups. S, N, L, in accordance with table 7. S : for short engagement N : for normal engagement L : for long engagement 0
TABLE 9 - MINIMUM ROOT RADII OF BOLTS PITCH P mm 0. 0. 0. 0. 0. 0. 0. 0.6 0.7 0.7 0.8 1 1. 1. 1.7.... 6 R min μm 1 8 0 6 6 7 88 9 100 1 16 188 19 0 1 7 8 00 6 6 688 70..1. Compliance The supplier/manufacturer shall not deliver any workpiece that the actual thread size (for example the pitch diameter) of which lies outside the specified limits. Compliance with specified limits shall be verified according to ISO 10...1. Designation General purpose metric screw threads are designated in accordance with ISO 96/1... Specification of nuts and/or bolts with miniature screw thread If nuts and/or bolts with miniature screw thread required, the requirements shall conform, to ISO/R 101... Specification of nuts and/or bolts with metric trapezoidal screw threads...1 Basic profile The basic profile of metric trapezoidal screw threads "if required" shall conform to ISO 901.... Basic dimensions The basic dimensions of nuts and/or bolts with trapezoidal screw threads shall conform to ISO 90.... es...1 es for single start threads The tolerance class of required workpiece shall be the denoted class in data-sheet and/or the 1
relevant workpiece specification which may be selected from Table 10 for nut threads and Table 11 for bolt threads; TABLE 10 - TOLERANCE CLASSES FOR NUT THREADS TOLERANCE QUALITY Medium Coarse TOLERANCES FOR THE PITCH DIAMETER 7H 8H Note: In Table 10 Figs 7 and 8 denote to the tolerance classes and H denotes to the fundamental deviation. TABLE 11 - TOLERANCE CLASSES FOR BOLT THREADS TOLERANCE QUALITY Medium Coarse TOLERANCES FOR THE PITCH DIAMETER 7e 8c Note: In Table 11 Figs 7 and 8 denote to the tolerance classes and e and c denote to the fundamental deviation. The numerical values of each class shall be selected accordingly from Tables,,, 6 and 7 of ISO 90.... for multiple-start threads of multiple-start threads shall comply with ISO 90.... Designation Metric trapezoidal threads shall be designated in accordance with ISO 90 and ISO 90... Specification for tapping screw threads...1 profile The profile of tapping screw threads shall be in accordance with Fig..
THREAD PROFILE Fig.... Dimensions Dimensions of tapping screws thread referred to Fig. and Fig. and Fig. shall comply with Table 1. Fig. TYPE C CONE AND TYPE F FLAT END (PREVIOUSLY TYPE AB) (PREVIOUSLY TYPE B) THREAD ENDS Fig.
TABLE 1 - DIMENSIONS Dimensions in mm THREAD ST ST ST ST ST ST ST ST ST ST ST ST ST ST SIZE 1. 1.9..6.9...9..8. 6. 8 9. P 0. 0.6 0.8 0.9 1.1 1. 1. 1. 1. 1.6 1.8 1.8.1.1 d 1 max. 1. 1.90..7.9...91..8.6 6. 8 9.6 min. 1.8 1.76.1..76.1..7.0.6.8 6.0 7.78 9. d max. 0.91 1. 1.6 1.90.18.9.6.9.10.8.17.88 6.0 7.8 min. 0.8 1.17 1. 1.80.08.9.1.77.96..99.70.99 7.9 d max. 0.79 1.1 1.7 1.7.01.1.1.67.8.0.86..8 7. min. 0.69 1.0 1.7 1.60 1.88.08.6.1.69.1.68..6 7. c max. 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 y Type C 1. 1.6..6...7. 6 7. 8 Type F 1.1 1. 1.6 1.8.1...7.8..6.6..... Designation Tapping screw threads shall be designated with "ST" followed by the nominal value of the thread diameter. For example ST..... Compliance The supplier/manufacturer shall not deliver any workpiece that the actual thread size of which liese outside the specified values.. Specific Requirements for Screws..1 Slotted and/or cross recessed screws..1.1 Specification for raised countersunk (oval) head tapping screws which may be ordered with thread size of either ST.,ST., ST., ST.8, ST., ST 6., ST 8 and ST 9. shall be as given in Table 1 and the dimensions of required screws "as data sheet" shall comply with ISO 18 "if screws are slotted" and with ISO 701 "if the screws are cross recessed type". TABLE 1 - SPECIFICATION FOR RAISED COUNTERSUNK (OVAL) HEAD TAPPING SCREWS MATERIAL, ACCORDING TO ISO 70 According to Clause.. properties According to ISO 70 1) A ISO 79/1 Plain Requirements for electroplating are covered in ISO 0 Acceptability Acceptance procedure shall be in accordance with ISO 69 1) As denoted in ISO 79/1 the product grades refer to the quality of the product and to the size of the tolerances, where grade A is the most precise and grade C is the less precise...1. Specification for countersunk (flat) head tapping screws which may be ordered with thread size of either ST., ST., ST., ST.8, ST., ST 6., ST 8, and ST 9. shall be as given in Table 1 and the dimensions of required screws "as data sheet" shall comply with ISO 18 "if the screws are slotted and with ISO 700" if the screw are cross recessed type.
TABLE 1 - SPECIFICATION FOR COUNTERSUNK (FLAT) HEAD TAPPING SCREWS MATERIAL According to Clause.. properties According to ISO 70 1) A ISO 79/1 Plain Requirements for electroplating are covered in ISO 0 Acceptability Acceptance procedure shall be in accordance with ISO 69..1. Specification for countersunk flat head screws (common head style) which may be ordered with thread size of either M1.6, M, M, M, M, M6, M8 and M10, shall be as given in Table 1 and dimensions of required screws "as data sheet" shall comply with ISO 009 "if the screw is slotted" and with ISO 706 "if the screw is cross recessed type". Note: Cross recessed screws may be of Z or H type "as denoted in data sheet". TABLE 1 - SPECIFICATION FOR COUNTERSUNK HEAD SCREWS MATERIAL STAINLESS 6g According to Clauses..1. and..1. NON-FERROUS METAL.8 1) A-70, A-0 1) and ).8 properties Property class (According to data sheet) ISO 898/1 (According to data sheet) ISO 06 In accordance with ISO 889 A ISO 79/1 Plain Requirements for electroplating are covered in ISO 0 Acceptability Acceptance procedure shall be in accordance with ISO 69 1) Max. hardness HV permissible. ) This property class is for slotted type only and not for cross recessed types...1. Specification for raised countersunk head screw (common head style) which may be ordered with thread size of either M1.6, M, M, M, M, M6, M8 or M10 shall be as given in Table 16 and dimensions of required screws "as data sheet" shall comply with ISO 010 "if the screw is slotted type" and with ISO 707 "if the screw is cross recessed type". Note: Cross recessed screws may be of H or Z type as denoted in data sheet.
TABLE 16 - SPECIFICATION FOR RAISED COUNTERSUNK HEAD SCREWS MATERIAL STAINLESS 6g According to Clauses..1. and..1. NON-FERROUS METAL.8 1) A-70, A-0 1) and ).8 properties Property class (According to data sheet) ISO 898/1 (According to data sheet) ISO 06 In accordance with ISO 889 A ISO 79/1 Plain Requirements for electroplating are covered in ISO 0 Acceptability Acceptance procedure shall be in accordance with ISO 69 1) Max. hardness HV permissible. ) This property class is for slotted types and not for cross recessed types...1. Specification for pan head screws (slotted or cross recessed type) which may be ordered with thread size of either M1.6,M, M., M, M, M, M6, M8 and M10 shall be as given in Table 17 and dimensions of required screws "as data sheet" shall comply with ISO 180 "if the screw is slotted pan head type" and with ISO 70 "if the screw is cross recessed pan head type". Note: Cross recessed screws may be of Z type or H type as denoted in data sheet". 6
TABLE 17 - SPECIFICATION FOR PAN HEAD SCREWS MATERIAL STAINLESS 6g According to Clauses..1. and..1. NON-FERROUS METAL.8 1) A-70, A-0 1) and ).8 properties Property class (According to data sheet) ISO 898/1 (According to data sheet) ISO 06 In accordance with ISO 889 A ISO 79/1 Plain Requirements for electroplating are covered in ISO 0 Acceptability Acceptance procedure shall be in accordance with ISO 69 1) Max. hardness HV permissible. ) This property class is applicable only for slotted pan head and shall not be applied for cross recessed pan head screws...1.6 Specification for slotted cheese head screws which may be ordered with thread size either M, M, M6, M8 and shall be as given in Table 18 and dimensions of required screws "as data sheet" shall comply with ISO 107. TABLE 18 - SPECIFICATIONS FOR SLOTTED CHEESE HEAD SCREWS MATERIAL STAINLESS 6g According to Clauses..1. and..1. NON-FERROUS METAL.8 1) A-70, A-0 1) and ).8 Properties Property class (According to data sheet) ISO 898/1 (According to data sheet) ISO 06 In accordance with ISO 889 A ISO 79/1 Plain Requirements for electroplating are covered in ISO 0 Acceptability Acceptance procedure shall be in accordance with ISO 69 1) Max. hardness HV permissible...1.7 Specification for pan head tapping screws which may be ordered with thread size of either ST., ST.9, ST., ST., ST.8, ST., ST6., ST8 and ST9. shall be as given in Table 19 and dimensions of required screws "as data sheet" shall comply with ISO 181 "if the screw is slotted" 7
and with ISO 709 "if the screw is cross recessed type". TABLE 19 - SPECIFICATION FOR SLOTTED PAN HEAD TAPPING SCREWS MATERIAL, ACCORDING TO ISO 70 According to Clause.. properties According to ISO 70 A ISO 79/1 Plain Requirements for electroplating are covered in ISO 0 Acceptability Acceptance procedure shall be in accordance with ISO 69..1.8 Specification for slotted set screws with cone point which may be ordered with thread size of either M1., M1.6, M, M., M, M, M, M6, M8, M10 and M1 shall be as given in Table 0 and dimensions of required screw "as data sheet" shall comply with ISO 7. TABLE 0 - SPECIFICATION FOR SLOTTED SET SCREWS WITH CONE POINT MATERIAL STAINLESS 6g According to Clauses..1. and..1. NON-FERROUS METAL 1 H, H A1-0 Properties Property class (According to data sheet) ISO 898/ ISO 06 In accordance with ISO 889 A ISO 79/1 Plain Requirements for electroplating are covered in ISO 0 Acceptability Acceptance procedure shall be in accordance with ISO 69..1.9 Specification for slotted set screws with long dog point which may be ordered with thread size of either M1.6, M, M., M, M, M, M6, M8, M10, and M1 shall be as given in Table 1 and dimensions of required screws "as data sheet" shall comply with ISO 7. 8
TABLE 1 - SPECIFICATIONS FOR SLOTTED SET SCREWS WITH LONG DOG POINT MATERIAL STAINLESS 6g According to Clauses..1. and..1. NON-FERROUS METAL 1 H, H A1-0 Properties Property class (According to data sheet) ISO 898/ ISO 06 In accordance with ISO 889 A ISO 79/1 Plain Requirements for electroplating are covered in ISO 0 Acceptability Acceptance procedure shall be in accordance with ISO 69..1.10 Specification for slotted set screws with flat point which may be ordered with thread size of either M1., M1.6, M, M., M, M, M, M6, M8, M10, and M1 shall be as given in Table and dimensions of required screws "as data sheet" shall comply with ISO 766. TABLE - SPECIFICATIONS FOR SLOTTED SET SCREWS WITH FLAT POINT MATERIAL STAINLESS 6g According to Clauses..1. and..1. NON-FERROUS METAL 1 H, H A1-0 Properties Property class (According to data sheet) ISO 898/ ISO 06 In accordance with ISO 889 A ISO 79/1 Plain Requirements for electroplating are covered in ISO 0 Acceptability Acceptance procedure shall be in accordance with ISO 69..1.11 Specification for slotted set screws with cup point which may be ordered with thread size of either M1.6, M, M., M, M, M, M6, M8, M10, or M1 shall be as given in Table and dimensions of required screws "as data sheet" shall comply with ISO 766. 9
TABLE - SPECIFICATIONS FOR SLOTTED SET SCREWS WITH CUP POINT MATERIAL STAINLESS 6g According to Clauses..1. and..1. NON-FERROUS METAL 1 H, H A1-0 Properties Property class (According to data sheet) ISO 898/ ISO 06 In accordance with ISO 889 A ISO 79/1 Plain Requirements for electroplating are covered in ISO 0 Acceptability Acceptance procedure shall be in accordance with ISO 69.. Hexagon screws...1 Specification for hexagon head screws-grades A and B...1.1 Hexagon head screws with thread size of either M1.6, M, M., M, M, M, M6, M8, M10, M1, M16, M0 and M and/or nominal lengths up to and including 10d or 10 mm "whichever is shorter" shall be grade A and with thread size of either M0, M6, M, M8, M6 or M6 and /or nominal length over 10d or 10 mm "which ever is shorter" shall be Grade B....1. Dimensions of required screws "as indicated in data sheet" shall comply with ISO 017....1. If fine pitch thread are required, dimensions shall conform with ISO 8676....1. Other requirement shall comply with Table. 0
TABLE - SPECIFICATION FOR HEXAGON HEAD SCREWS-GRADES A AND B MATERIAL STAINLESS 6g According to Clauses..1. and..1. NON-FERROUS METAL d < mm: as agreed or denoted in data sheet mm d 9 mm:.6, 8.8, 10.9 (in accordance with data sheet) d > 9 mm: as agreed or denoted d 0 mm: A -70 0 mm < d 9 mm: A-0 d > 9 mm: as agreed Properties Property class in data sheet d 9mm : ISO898 _1d mm and d > 9 mm: as agreed or denoted in data sheet or denoted in data sheet d 9 mm : ISO 06 d > 9 mm: as agreed ISO 889 1) For d mm and l 10 d or 10 mm : A For d mm or l >10 d or 10 mm : B ISO 79/1 As processed Plain Plain Requirements for electroplating are covered in ISO 0 Limits for surface discontinuities are covered in ISO 617-1 and ISO 617- Acceptability Acceptance procedure shall be in accordance with ISO 69 1) Whichever is shorter.... Specification for hexagon head screws-grade C shall be as given in Table and dimensions of required screws "as data sheet" shall comply with ISO 018. Note: Grade C hexagon head screws shall only be supplied with threads size of either M, M6, M8, M10, M16, M0, M, M0, M6, M, M8, M6, and M6 and unless otherwise specified in data sheet. Non-Preferred s which are mentioned in ISO 018 shall not be supplied. Properties TABLE - SPECIFICATION FOR HEXAGON HEAD SCREWS - GRADE C MATERIAL Property class 8g According to Clauses..1. and..1. d 9 mm:.6,.6,.8 d > 9 mm :as agreed or denoted in data sheet d 9 mm : ISO 898-1 C ISO 79/1 As processed Requirements for electroplating are covered in ISO 0 Acceptability Acceptance procedure shall be in accordance with ISO 69... Specification for Hexagon socket set screws with flat point which may be ordered with thread size of either M1.6, M, M., M, M, M, M6, M8, M10, M1, M16, M0 and M, shall be as given in Table 6 and dimensions of required screws "as data sheet" shall comply with ISO 06. 1
TABLE 6 - SPECIFICATIONS FOR HEXAGON SOCKET SET SCREWS WITH FLAT POINT MATERIAL STAINLESS 6g According to Clauses..1. and..1. NON-FERROUS METAL Property class.h Properties ISO 898/V A ISO 79/1 AI 0 ISO 06 In accordance with ISO 889 Black oxide Plain Plain (Thermal or chemical) Requirements for electroplating are covered in ISO 0 Acceptability Acceptance procedure shall be in accordance with ISO 69... Specification for Hexagon socket set screws with cone point which may be ordered with thread size of either M1.6, M, M., M, M, M, M6, M8, M10, M1, M16, M0 and M, shall be as given in Table 7 and dimensions of required screws "according to data sheet" shall conform with ISO 07. TABLE 7 - SPECIFICATIONS FOR HEXAGON SOCKET SET SCREWS WITH CONE POINT MATERIAL STAINLESS 6g According to Clauses..1. and..1. NON-FERROUS METAL Property class.h Properties ISO 898/V A ISO 79/1 AI 0 ISO 06 In accordance with ISO 889 Black oxide Plain Plain (Thermal or chemical) Requirements for electroplating are covered in ISO 0 Acceptability Acceptance procedure shall be in accordance with ISO 69... Specification for Hexagon socket set screws with dog point which may be ordered with thread size of either M1.6, M, M., M, M, M, M6, M8, M10, M1, M16, M0 and M, shall be as given in Table 8 and dimensions of required screws "according to data sheet" shall comply with ISO 08.
TABLE 8 - SPECIFICATIONS FOR HEXAGON SOCKET SET SCREWS WITH DOG POINT MATERIAL STAINLESS 6g According to Clauses..1. and..1. NON-FERROUS METAL Property class.h Properties ISO 898/V A ISO 79/1 AI 0 ISO 06 In accordance with ISO 889 Black oxide Plain Plain (Thermal or chemical) Requirements for electroplating are covered in ISO 0 Acceptability Acceptance procedure shall be in accordance with ISO 69...6 Specification for Hexagon socket set screws with cup point which may be ordered with thread size of either M1.6, M, M., M, M, M, M6, M8, M10, M1, M16, M0 and M, shall be as given in Table 9 and dimensions of required screws "according to data sheet" shall comply with ISO 09. TABLE 9 - SPECIFICATIONS FOR HEXAGON SOCKET SET SCREWS WITH CUP POINT MATERIAL STAINLESS 6g According to Clauses..1. and..1. NON-FERROUS METAL Property class.h Properties ISO 898/V A ISO 79/1 AI 0 ISO 06 In accordance with ISO 889 Black oxide Plain Plain (Thermal or chemical) Requirements for electroplating are covered in ISO 0 Acceptability Acceptance procedure shall be in accordance with ISO 69...7 Specification for Hexagon socket head cap screws-product grade A which may be ordered with thread size ofeither M1.6, M, M., M, M, M, M6, M8, M10, M1, M16, M0, M, M0 or M6, shall be as given in Table 0 and dimensions of required screws "according to data sheet" shall comply with ISO 76.
TABLE 0 - SPECIFICATIONS FOR HEXAGON SOCKET HEAD CAP SCREWS-PRODUCT GRADE A MATERIAL 1) STAINLESS 6g According to Clauses..1. and..1. NON-FERROUS METAL Properties Property class 8.8, 1.9 as specified in data sheet ISO 898-1 ) d 0 mm: - A - 70 d > 0 mm :- A - 0 ISO 06 In accordance with ISO 889 A ISO 79/1 Black oxide Plain Plain (Thermal or chemical) Requirements for electroplating are covered in ISO 0 Acceptability Acceptance procedure shall be in accordance with ISO 69 1) Alloy steel is mandatory as the material for screws of property class 1.9. ) For screws unsuitable for tensile testing, the hardness requirements shall be complied with, throughout the section of the screw....8 Specification for hexagon socket head shoulder screws which may be ordered with shoulder diameters of either 6., 8, 10, 1, 16, 0 and shall be as given in Table 1 and dimensions of required screws "according to data sheet" shall comply with ISO 779. Properties TABLE 1 - SPECIFICATION FOR HEXAGON SOCKET HEAD SHOULDER SCREWS MATERIAL Property class Shoulder Other features 6g According to Clauses..1. and..1. 1) 1.9 ISO 898-1 A ISO 79/1 To surface roughness of Ra value = 0.8 mm in accordance with ISO10. only apply before electroplating Black oxide (Thermal or chemical) Requirements for electroplating are covered in ISO 0 Acceptability Acceptance procedure shall be in accordance with ISO 69 1) Because of their configuration these screws cannot be subjected to tensile testing. They are nevertheless required to meet allthe other material and property requirements for property class 1.9....9 Specification for hexagon socket button head Screws which may be ordered with thread size of either M, M, M, M6, M8, M10, M1 and M16 shall be as given in Table and dimensions of required screws "according to data sheet" shall comply with ISO 780.
TABLE - SPECIFICATION FOR HEXAGON SOCKET BUTTON HEAD SCREWS Properties MATERIAL Property class 6g According to Clauses..1. and..1. 1) 1.9 ISO 898-1 A ISO 79/1 Black oxide (Thermal or chemical) Requirements for electroplating are covered in ISO 0 Acceptability Acceptance procedure shall be in accordance with ISO 69 1) Because of their head configurations, these screws may not meet the minimum ultimate tensile load for property Class 1.9, specified in ISO 898/1, Table 6, when tested in accordance with test program B. They are nevertheless required to meet the other material and property requirements for property Class 1.9 in ISO 898/1. In addition, when normally loaded with the head supported on a parallel collar using the type of testing fixture illustrated in ISO 898/1, Fig., they shall withstand the following loads without fracture: THREAD SIZE d M M M M 6 M 8 M 10 M 1 M 16 Test load, kn. 9.1 1.8 0.9 8.1 60. 87.7 6 If tested to failure, the fracture may occur in the threaded section, the head or at the headshank junction....10 Specification for hexagon head tapping screws which may be ordered with thread size of either ST., ST.9, ST., ST., ST.8, ST., ST6., ST8 and ST9. shall be as given in Table and dimensions of required screws "according to data sheet" shall comply with ISO 179. TABLE - SPECIFICATION FOR HEXAGON HEAD TAPPING SCREWS MATERIAL, ACCORDING TO ISO 70 According to Table 17 A ISO 79/1 Plain Requirements for electroplating are covered in ISO 0 Acceptability Acceptance procedure shall be in accordance with ISO 69...11 Specification for hexagon set screws with small hexagon and full dog point which may be ordered with thread sizes of either M6, M8, M10, M1, M0, M, M0, M6, M, M8 and M6 shall comply with Table and dimensions of required screw according to data sheet shall be in accordance with DIN 61.
TABLE - SPECIFICATION FOR HEXAGON SET SCREWS WITH SMALL HEXAGON AND FULL DOG POINT Properties Acceptability MATERIAL Property class 6g According to Clauses..1. and..1..6.88.8 In accordance with data sheet ISO 898 Part 1 A ISO 79/1Part As processed Property class 8.8 screws: (thermally or chemically) blackened. DIN 67 part shall apply with regard to surface roughness. ISO 617-1 shall apply with regard to permissible surface discontinuities. ISO 0 shall apply with regard to electroplating. DIN 67 part 10 shall apply with regard to hot dip galvanizing. ISO 69 shall apply with regard to the acceptance inspection. 1...1 Specification for hexagon head set screws with small hexagon and coned half dog point which may be ordered with thread sizes of either M6, M8, M1, M16, M0, M, M0, or M6, shall comply with Table and dimensions of required screw as denoted in data sheet shall be in accordance with DIN 61. TABLE - SPECIFICATION FOR HEXAGON HEAD SET SCREWS WITH SMALL HEXAGON AND CONED HALF DOG POINT Properties Acceptability MATERIAL Property class 6g According to Clauses..1. and..1..6.88.8 In accordance with data sheet ISO 898 Part 1 A ISO 79/1Part As processed Property class 8.8 screws: (thermally or chemically) blackened. DIN 67 part shall apply with regard to surface roughness. ISO 617-1 shall apply with regard to permissible surface discontinuities. ISO 0 shall apply with regard to electroplating. DIN 67 part 10 shall apply with regard to hot dip galvanizing. ISO 69 shall apply with regard to the acceptance inspection. 1...1 Specification of hexagon socket thin head cap screws with pilot recess for wrench key which may be ordered with thread sizes of either M, M, M6, M8, M10, M1, M16, M0, M, M0 and M6 shall comply with Table 6 and dimensions of required size "as denoted in data sheet" shall be in accordance with DIN 691. If hexagon socket thin head cap screws without pilot recess for wrench are required, the dimensions of required size may be either M, M, M, M6, M8, M10, M1, M16, M0 or M, shall comply with DIN 798. Other specifications shall be in accordance with above mentioned table. 6
TABLE 6 - SPECIFICATION OF HEXAGON SOCKET THIN HEAD CAP SCREWS WITH PILOT RECESS FOR WRENCH KEY MATERIAL STAINLESS 6g According to Clauses..1. and..1. NON-FERROUS METAL Properties Property class 8.8 ISO 898 1) Part 1 M0 : - A - 70 > M0:- A - 0 ISO 06 ) CuZn = copper - zinc alloy ISO 889 A ISO 79/1 (Thermally or chemically) Bright Bright blackened DIN 67 part shall apply with regard to surface roughness. ISO 617-1 shall apply with regard to permissible surface discontinuities. ISO 0 shall apply with regard to electroplating. Acceptability Acceptance procedure shall be in accordance with ISO 69 1) The acceptance inspection shall include hardness testing of property class 8.8 screws, with hardness values of HV 0 to 0 for sizes up to and including M:6 and HV to for sizes greater than M16. ) Preferably CU or CU, at the manufacturer s discretion. Specific Requirements for Bolts The thread lengths shown in Table 8 apply to bolts of metric sizes. Table 7 contains the formulas on which the calculation of the thread lengths indicated in Table 8 was based. For dimensioning of thread lengths, see ISO. TABLE 7 - FORMULAS FOR CALCULATION OF THREAD LENGTH Mm NOMINAL LENGTH FORMULAE FOR Over To THREAD LENGTHS --- 1 d + 6 1 00 d + 1 00 --- d + 7
TABLE 8 - ALLOCATION OF THE THREAD LENGTHS TO THE BOLT DIAMETERS DIMENSIONS IN MILLIMETERS THREAD DIAMETER d 1.6. 6 7 8 10 1 1 16 18 0 l 1 9 10 11 1 1 16 18 0 6 0 8 6 length 1 < l 00 --- --- --- --- --- --- --- --- 8 6 0 8 b l > 00 --- --- --- --- --- --- --- --- --- --- --- --- 7 61 6 THREAD DIAMETER d 7 0 6 9 8 6 l 1 0 60 66 7 78 8 90 96 10 --- --- --- --- --- length 1 < l 00 6 60 66 7 78 8 90 96 10 108 116 1 1 10 18 b l > 00 69 7 79 8 91 97 10 109 11 11 19 17 1 1 16 Note: b: denotes to the thread length and, l: denotes to the nominal length. For more information see ISO...1 Specification of hexagon head bolts-grades A & B..1.1 Hexagonal head bolts of grades A or B with threads of either M1.6, M, M., M, M, M, M6, M8, M10, M1, M16, M0 or M and nominal length up to and including 10 d or 10 mm "whichever is shorter" shall be grade A and with threads of either M0, M6, M, M8, M6, M6 and nominal length over 10d or 10 mm (whichever is shorter) shall be Grade B...1. Dimensions of required bolts "as indicated in data sheet" shall comply with ISO 01 and non-preferred threads in the mentioned standard shall not be supplied...1. Other requirements shall conform with Table 9. Note: If reduced shank diameter is required, dimensions and other requirements shall comply with ISO 01. 8
TABLE 9 - SPECIFICATION FOR HEXAGON HEAD BOLTS-GRADES A AND B MATERIAL STAINLESS 6g According to Clauses..1. and..1. NON- FERROUS METAL Properties Property class d < mm: as agreed or specified in data sheet mm d 9 mm:.6 1), 8.8 ), 10.9 ) (see data sheet) d > 9 mm: as agreed or denoted in data sheet mm d 9 mm :ISO 8998-1 d < mm and d > 9 mm as agreed d 0 mm: A-70 0 mm < d 9 mm: A-0 d > 9 mm: as agreed or denoted in data sheet d 9 mm : ISO 06 d > 9 mm: as agreed ISO 889 ) For d mm and l 10 d or 10 mm : A For d > mm or l >10 d or 10 mm ISO 79/1 As processed Plain Plain Requirements for electroplating are covered in ISO 0 Limits for surface discontinuities are covered in ISO 617-1 and ISO 617- ) : B Acceptability Acceptance procedure shall be in accordance with ISO 69 1) For bolts with property class of.6 with all diameter range, the mating nuts with nominal height range of 0.8D shall have the property class of at least. ) Property class of mating nuts with nominal height range of 0.8D shall be 8. ) Property class of mating nuts with nominal height range of 0.8D shall be at least 10. ) Whichever is shorter... Specification for hexagon head bolts-grade C shall be as given in Table 0 and dimensions of required bolts "as denoted in data sheet" shall comply with ISO 016. Notes: 1) Grade C hexagon head bolts are not in prime consider and shall only be supplied if ordered in special cases otherwise bolts mentioned in..1 shall be supplied. ) Grade C hexagon head bolts shall only be supplied with threads of either M, M6, M8, M10, M1, M16, M0, M, M0, M6, M, M8, M6 and M6. ) Unless otherwise specified in data sheet, non-preferred threads given in ISO 016 shall not be supplied. ) If metric hexagon bolts for high-strength structural bolting with large width across flats are required the requirements shall comply with ISO 711. ) If metric hexagon bolts for high-strength structural bolting with large width across flats but with short thread length is required "shorter than those mentioned in ISO 016 the requirements shall comply with ISO 71. 9
TABLE 0 - SPECIFICATION FOR HEXAGON HEAD BOLTS-GRADE C Properties MATERIAL Property class 8g According to Clauses..1. and..1. d 9 mm:.6 1),.6 1),.8 1) according with data sheet d > 9 mm :as agreed or denoted in data sheet d 9 mm : ISO 898-1 d > 9 mm: as agreed C ISO 79/1 As processed Requirements for electroplating are covered in ISO 0 Acceptability. For acceptance procedure, see ISO 69 1) Property class of mating nut with nominal height of Ý 0.8D "if required" shall be at least if the diameter range of bolts are more than 16 mm and shall be at least if the diameter range of bolts are equal to M16 and/or less than that... Specification for cup head square neck bolts with large head-grade C shall be as given in Table 1 and dimensions of required bolts "as denoted in data sheet" which may be ordered with thread size of either M, M6, M8, M10, M1, M16 and M0 shall comply with ISO 8677. TABLE 1 - SPECIFICATION FOR CUP HEAD SQUARE NECK BOLTS WITH LARGE HEAD- GRADE C Properties MATERIAL Property class 6g According to Clauses..1. and..1. 8.8 ) (In accordance with data sheet) ISO 898/1 C ISO 79-1 As processed Black oxide (thermic or chemical) for product class 8.8 Requirements for electroplating are covered in ISO 0. For hot dip galvanizing, see ISO 161. Acceptability. For acceptance procedure, see ISO 69. 1) Property class of mating nut with nominal height of 0.8D "if required" shall be at least if the diameter range of bolts are more than 16 mm and shall be at least if the diameter range of bolts are equal to M16 and or less than that. ) Property class of mating nut with nominal height of 0.8D shall be 8... Specification for cup head square neck bolts with small head and short neck-grade B....1 This bolts may be ordered with thread size of either M6, M8, M10, M1, M16 and M0.... Dimensions of this kind of bolts shall comply with ISO 8678 and other specifications shall be in accordance with Table. 0
TABLE - SPECIFICATIONS FOR CUP HEAD SQUARE NECK BOLTS WITH SMALL HEAD AND SHORT NECK-GRADE B Properties MATERIAL Property class 6g According to Clauses..1. and..1. 1) ) ), 8, 8.8,10.9 ISO 898-1 B ISO 79-1 As processed Black oxide (thermic or chemical) for product class 8.8 Requirements for electroplating are covered in ISO 0. For hot dip galvanizing, see ISO 161. Acceptability. For acceptance procedure, see ISO 69. 1) For bolts with diameter range of > M 16 the property class of mating nut with the nominal height of 0.8D shall be at least and for bolts with diameter range of 16M the property class of mating nut with the nominal height of 0.8D shall be at least. ) The mating nut with the nominal height of 0.8D shall have the property class of at least 8. ) The mating nut with the nominal height of 0.8D shall have the property class of at least 10... Specification for hexagon flange bolts-small series, which may be ordered with threads of either M, M6, M8, M10, M1 and M16 with property classes of either 8.8 to 10.9 "according to ISO 898-1 or A-70" according to ISO 06 shall be as given in Table. Dimensions of required bolts "according to data sheet" shall comply with ISO 16. TABLE - SPECIFICATION FOR HEXAGON FLANGE BOLTS-SMALL SERIES Properties MATERIAL Property class 6g According to Clauses..1. and..1. 8.8 1), 9.8 ), 10.9 ) in accordance with data sheet ISO 898-1 A ISO 79-1 A - 70 ISO 06 Black oxide (Thermic or chemical) Plain Requirements for electroplating are covered in ISO 0. Limits for surface discontinuities are covered in ISO 617-1 and ISO 617-. Acceptability. Acceptance procedure, shall be in accordance with ISO 69. 1) Property class of mating nuts with nominal heights of 0.8D shall be at least 8. ) Property class of mating nuts with nominal heights of 0.8D shall be at least 9. ) Property class of mating nuts with nominal heights of 0.8D shall be at least 10. 1
..6 Specification for hexagon head bolts with metric fine pitch thread-grades A and B...6.1 This kind of bolts may be ordered with nominal thread diameter,d, from 8 to 6 mm. Product grade A may have nominal thread diameter,d, of either 8, 10, 1, 16, 0 and mm and nominal length,l, up to and including 10d or 10 mm, whichever is shorter. B may have nominal thread diameters of either 0, 6,, 8, 6 and 6 mm and nominal length over 10d or 10 mm, whichever is shorter...6. Dimensions of required bolts "according to data sheet" shall comply with ISO 876. Unless otherwise specified in data sheet, non preferred threads in the above mentioned standard shall not be supplied...6. Other specifications shall be as given in Table. TABLE - SPECIFICATION FOR HEXAGON HEAD BOLTS WITH METRIC FINE PITCH THREAD-GRADES A AND B MATERIAL STAINLESS 6g According to Clauses..1. and..1. NON- FERROUS METAL Properties Property class d < 9 mm:.6 1), 8.8 ), 10.9 ) as specified in data sheet d > 9 mm: as agreed or denoted in data sheet d 9 mm : ISO 8998-1 d 0 mm: A-70 0 mm < d 9 mm: A-0 d > 9 mm: as agreed or denoted in data sheet d 9 mm : ISO 06 d > 9 mm: as agreed ISO 889 d > 9 mm as agreed For d mm and l 10 d or 10 mm: A For d > mm or l >10 d or 10 mm : B ISO 79/1 As processed Plain Plain Requirements for electroplating are covered in ISO 0 If different electroplating requirements are desired or if requirements are needed for other finishes, they should be agreed between company and supplier. Limits for surface discontinuities are covered in ISO 617-1 and ISO 617- Acceptability Acceptance procedure shall be in accordance with ISO 69 1) The property class of mating nuts with nominal heights of 0.8D shall be at least. ) The property class of mating nuts with nominal heights of 0.8D shall be at least 8. ) The property class of mating nuts with nominal heights of 0.8D shall be at least 10...7 Specification for hexagon fit bolts with short threaded dog point which may be ordered with thread size of either M8, M10, M1, M16, M0, M, M0, M6, M and M8 shall comply with Table and dimensions of required bolt "as denoted in data sheet" shall be in accordance with DIN 610.
TABLE - SPECIFICATION FOR HEXAGON FIT BOLTS WITH SHORT THREADED DOG POINT MATERIAL STAINLESS 6g According to Clauses..1. and..1. NON-FERROUS METAL Properties 1) Property class M9 : 8.8 ) > M9 : subject to agreement if not denoted in data sheet ISO898 Part 1 M0 : A-70; M0 < M9 : A-0; > M9 : subject to agreement if not denoted in data sheet ISO 06 e.g.cu, CU ISO889 ) M10 : A > M1: B ISO 79/1 Blackened ) Bright Bright (Thermally or chemically) Fit shank: bright DIN 67 part shall apply with regard to surface roughness. ISO 617-1 shall apply with regard to permissible surface discontinuities. ISO 0 shall apply with regard to electroplating. DIN 67 part 10 shall apply with regard to hot-dip galvanizing. Acceptability Acceptance procedure shall be in accordance with ISO 69 1) Where, for special purposes, the bolts are to meet requirements differing from those specified, e.g., in respect of property class or material, the specifications of the relevant standards shall be complied with. ) Property class of mating nuts with nominal height of > 0.8D shall be at least 8 or any higher classes. ) If product grade A is required for sizes from M1 upwards, this shall be incorporated in the designation, e.g.: Fit bolt DIN 610 - M0 100-8.8 - A in this case, the appropriate tolerances as specified in ISO 79 Part 1 shall apply. This does not apply however to the diameter of the fit shank. ) Different surfaces are the standard for different property classes or materials, as appropriate, e.g., "as rolled", i.e. without additional surface treatment, for property class.6...8 Specification of hexagon fit bolts with long threaded dog point which may be ordered with thread sizes of either M8, M10, M1, M16, M0, M, M0, M6, M and M8 shall comply with Table 6 and dimensions of required size as denoted in data sheet shall be in accordance with DIN 609.
TABLE 6 - SPECIFICATION OF HEXAGON FIT BOLTS WITH LONG THREADED DOG POINT MATERIAL STAINLESS 6g According to Clauses..1. and..1. NON-FERROUS METAL M9 : 8.8 ) Properties 1) Property class > M9 : subject to agreement if not denoted in data sheet ISO898 Part 1 M0 : A-70; M0 < M9 : A-0; > M9 : subject to agreement if not denoted in data sheet ISO 889 or DIN 67 part 18 e.g. CU, CU ISO 889 or DIN 67 part 18 ) M10 : A M1: B ISO 79/1 Blackened ) Bright Bright (Thermally or chemically) Fit shank: bright DIN 67 part shall apply with regard to surface roughness. ISO 617-1 shall apply with regard to permissible surface discontinuities. ISO 0 shall apply with regard to electroplating. DIN 67 part 10 shall apply with regard to hot-dip galvanizing. Acceptability Acceptance procedure shall be in accordance with ISO 69 1) Where, for special purposes, the bolts are to meet requirements differing from those specified, e.g., in respect of property class or material, the specifications of the relevant standards shall be complied with. ) Property class of mating nuts with nominal height of 0.8D shall be at least 8. ) If product grade A is required for sizes from M 1 upwards, this shall be incorporated in the designation, e.g.: Fit bolt DIN 609 - M0 100-8.8 - A in this case, the appropriate tolerances as specified in ISO 79 Part 1 shall apply. This does not apply however to the diameter of the fit shank. ) Different surfaces are the standard for different property classes or materials, as appropriate, e.g.,"as rolled", i.e. without additional surface treatment, for property class.6. ) The supply of electroplated fit bolts with bright shank is permitted...9 Specification of hexagon bolt with large width across flat..9.1 Dimensions of these bolts which are intended for use in high-tensile bolting in steel structure may be ordered with thread sizes of either M1, M16, M0, M, M, M7, M0 or M6...9. Dimensions of required size shall conform with DIN 691...9. General requirements shall be as given in sub-clause..1 and technical conditions of delivery shall comply with the above-mentioned standard if nuts and washers are required to be
supplied for use with these bolts, the nuts shall comply with DIN 691 and washers with DIN 6916 and DIN 6917...10 Specification of high strength hexagon fit bolts with large width across flats These bolts which are intended for use in structural steel bolting may be ordered with thread sizes of either M1, M16, M0, M, M, M7 or M0...10.1 Dimensions of required size shall conform with DIN 7999 and general requirements of these bolts shall comply with sub-clause..1 and technical conditions of delivery shall be in accordance with the above mentioned standard. In the case that nuts and washers are required to be supplied for use with these bolts, the nuts shall comply with requirements of DIN 691 and the washers shall comply with DIN 6916 and DIN 6917...11 Specification of square head bolts shall comply with Table 7..11.1 Dimensions of square head bolts with collar which may be ordered with thread size of either M, M6, M8, M10, M1, M16, M0 and M (in accordance with data-sheet) shall conform with DIN 78...11. Dimensions of square head bolts with short dog point which may be ordered with thread size of either M, M6, M8, M10, M1, M16, M0, or M (according to data-sheet) shall comply with DIN 79...11. Dimensions of square head bolts with collar and oval half dog point which may be ordered with thread size of either M8, M10, M1, M16, M0 and M (in accordance with data-sheet) shall conform with DIN 80. TABLE 7 - SPECIFICATION FOR SQUARE HEAD BOLTS MATERIAL 6g According to Clauses..1. and..1. Properties Acceptability Property class.6 1),.8 1), 8.8 ) ISO 898 part 1 A ISO 79 part 1 As processed Property class 8.8 bolts: (thermally or chemically) blackened. DIN 67 part shall apply with regard to surface roughness. ISO 617-1 and ISO 617- shall apply with regard to permissible surface discontinuities. ISO 0 shall apply with regard to electroplating. DIN 67 part 10 shall apply with regard to hot-dip galvanizing. ISO 69 shall apply with regard to the acceptance inspection. 1) Property class of mating nuts with nominal height of 0.8D shall be at least. ) Property class of mating nuts with nominal height of 0.8D shall be at least 8..6 Specific Requirements for Studs.6.1 Specification for various purpose stud bolts.6.1.1 Various purpose stud bolts which may be ordered either with as-rolled ends (type A) or with chamfered ends (type B)" shall be supplied with tolerance class of 6g "see figure in below".
TYPE A, WITH AS-ROLLED END TYPE B, WITH DIN 78-K THREAD ENDS (CHAMFERED ENDS) These studs may be required with thread sizes of either M, M., M, M, M, M6, M8, M10, M1, M16, M0, M, M0, M6, M, M8, M6 and M6. Length of stud bolts shall conform with datasheet which will be selected from DIN 976. Specifications of these studs shall comply with Table 8. TABLE 8 - SPECIFICATION OF VARIOUS PURPOSE STUD BOLTS MATERIAL STAINLESS 6g According to Clauses..1. and..1. NON-FERROUS METAL Properties 1) Property class.6,.6,.8 1) according to data sheet ISO 898 Part 1 A: A ISO 06 CuZn = copper-zinc alloy ) ISO 889 ) A ISO 79 Part 1 Acceptability As processed DIN 67 part shall apply with regard to surface roughness. ISO 617 shall apply with regard to permissible surface discontinuities. ISO 0 shall apply with regard to electroplating. DIN 67 part 10 shall apply with regard to hot-dip galvanizing. ISO 69 shall apply with regard to acceptance inspection. 1) The property class of mating nuts with nominal height of > 0.8D shall be at least. ) CuZn=CU or CU (as specified in DIN 67 part 18), at the manufacturer s discretion..7 Specific Requirements for Nuts Geometrical and mechanical properties of nuts are designed to provide for a high degree of resistance to stripping, so that the nut of an assembly shall have the capability of being tightened to the bolt proof load without thread stripping occurring. However, should tightening beyond bolt proof load take place, the nut design is intended to ensure 6
at least 10% of the over-tightened assemblies fail through bolt breakage in order to warn the user that his installation practice is not appropriate. Nuts shall be made of steel conforming to the chemical composition limits specified in Table 9. TABLE 9 - LIMITS OF CHEMICAL COMPOSITION PROPERTY CLASS CHEMICAL COMPOSITION LIMITS (CHECK ANALYSIS), % C Max. Mn min. P max. S max. 1) 1) 6 1) --- 0.0 --- 0.110 0.10 8 9 0 1) 0.8 0. 0.060 0.10 10 ) 0 ) 0.8 0.0 0.08 0.08 1 ) --- 0.8 0. 0.08 0.08 1) Nuts of these property classes may be manufactured from free-cutting steel unless otherwise specified in data-sheet. In such cases the following maximum sulphur, phosphorus and lead contents are permissible: Sulphur 0.% phosphorus 0.1%; lead 0.% ) Alloying elements may be added if necessary to develop the mechanical properties of the nuts. Nuts of property classes 0.8 (style 1> M16), 10 and 1 shall be hardened and tempered. properties of nuts with coarse threads shall at least comply with Table 0 when tested in accordance with Clause 8 of ISO 898/. 7
NORMAL SIZE (thread diameter) mm Proof stress S p TABLE 0 - MECHANICAL PROPERTIES (COARSE THREAD) PROPERTY CLASS 0 PROPERTY CLASS 0 PROPPERTY CLASS Vickers hardness HV Rockwell Hardness HRC Proof stress S p Vickers hardness HV Rockwell Hardness HRC Proof stress S p Vickers hardness HV Rockwell Hardness HRC over To N/mm min max min max N/mm min max min max N/mm min max min max - 7 7 10 80 00 188 0-0 10 16 16 9 6 100 - - 7 7.8 6 - - - - 10-117 0-0 NORMAL SIZE (thread diameter) mm Proof stress S p PROPERTY CLASS 0 PROPERTY CLASS 6 PROPPERTY CLASS 8 Vickers hardness HV Rockwell Hardness HRC Proof stress S p Vickers hardness HV Rockwell Hardness HRC Proof stress S p Vickers hardness HV Rockwell Hardness HRC over To N/mm min max min max N/mm min max min max N/mm min max min max - 0 600 800 170-7 80 670 810 10-10 - 0 7 10 90 680 80 188-0 0 0 0 10 16 610 700 80 16 9 60 16-70 1701-80 - 9 100-18 - - - - 07-0 8 NORMAL SIZE (thread diameter) mm Proof stress S p PROPERTY CLASS 9 PROPERTY CLASS 10 PROPPERTY CLASS 1 Vickers hardness HV Rockwell Hardness HRC Proof stress S p Vickers hardness HV Rockwell Hardness HRC Proof stress S p Vickers hardness HV Rockwell Hardness HRC over To N/mm min max min max N/mm min max min max N/mm min max min max - 900 170-100 110 7 91 100 110 9 n 1 7 10 90 0 0 100 1160 7 188-7 8 8 10 16 90 100 1190 8 8 16 9 90 1060 100 - - 9 100 - - - - - - - - - - - - - Note: Minimum hardness is mandatory only for heat-treated nuts and nuts too large to be proofload tested. For all other nuts, minimum hardness is provided for guidance only. Hardness values for nominal sixes (thread diameters) over 9 up to and including 100 mm are to be used for information and guidance only. If prevailing torque type steel hexagon nuts 1) are required, mechanical properties of such nuts "which may be ordered with thread sizes M to M9 inclusive" shall comply with Table 1. 8
THREAD SIZE mm Proof Stres s s p N/mm TABLE 1 - MECHANICAL PROPERTIES OF PREVAILING TORQUE TYPE HEXAGON NUTS PROPERTY CLASS PROPERTY CLASS 8 PROPERTY CLASS 9 Proof Proof Stres Stres Vickers Vickers Vickers Rockwell s Rockwell s Hardness Hardness Hardness Hadness s HV p Hadness s HV p HV HRC N/mm HRC N/mm Rockwell Hadness HRC ove mi Ma mi ma mi ma mi ma mi ma mi to min min min r n x n x n x n x n x n -- 0 800 170 -- 900 170 --- 7 8 0 810 91 1 10 -- 0 0 7 90 80 18 90 0 0 0 0 -- 188 1 10 610 80 90 6 --- 16 9 60 16 -- 90 6 90 Ma x 0 THREAD PROPERTY CLASS 10 PROPERTY CLASS 1 SIZE Proof Vickers Rockwell Proof Vickers Rockwell mm Stress s p N/mm Hardness HV Hadness HRC Stress s p N/mm Hardness HV Hadness HRC over to min min max min max min min max min max -- 100 7 8 6 110 9 9 6 7 100 110 7 10 100 1160 10 16 100 1190 16 9 1060 100 -- -- -- -- 1) Prevailing torque type nut: A nut which is frictionally resistant to rotation due to a selfcontained prevailing torque feature, and not because of a compressive load developed against the bearing surface of the nut..7.1 Specific requirements for hexagon nuts style 1- Grade A and B shall be as given in Table and dimensions of required nuts "as denoted in data sheet" shall comply with ISO 0. These nuts will be ordered with thread size of either M1.6, M, M., M, M, M, M6, M8, M10, M1, M16, M0, M, M0, M6, M, M8, M6 and M6. If fine pitch thread is required, the dimensions shall comply with ISO 867 which will be ordered with thread size of either M8, M10, M1, M16, M0, M, M0, M6, M, M8, M6 and M6. Unless otherwise specified in data sheet style 1 hexagon nuts are not in prime consider and nonpreferred sizes given in the above mentioned standards shall not be supplied. It is better to consider that style 1 hexagon nuts are thinner than style hexagon nuts for the same thread sizes. 9
TABLE - SPECIFICATION FOR HEXAGON NUTS STYLE 1 GRADES A AND B MATERIAL STAINLESS NON-FERROUS METAL 6g According to Clauses..1. and..1.and for fine pitch threads ISO 61and ISO 96 - Properties Property class d < M as agreed or denoted in data sheet M d M9: 6 1), 8 ), 10 ) d > M9 as agreed for fine-pitch threads d M9: 0, 0 d < M9 as agreed or denoted in data sheet M d M9 see.6 d < M and d > M9 as agreed or denoted in data sheet and for fine-pitch threads d M9: ISO 898-6 d > M9: as agreed or denoted in data sheet d M0: A-70 ) M0 < d M9: A-0 d > M9: as agreed or denoted in data sheet d M9 : ISO 06 d > M9: as agreed or denoted in data sheet ISO 889 d M16: A d > M16 : B ISO 79 part 1 As processed Plain Plain Requirements for electroplating are covered in ISO 0 Acceptability Acceptance procedure shall be in accordance with ISO 69 1) The property class of mating bolt shall be 6.8 or any other class that the assembly have the capability of being tightened to the bolt proof load without thread stripping occurring. ) The property class of mating bolt shall be 8.8 or any other class that the assembly have the capability of being tightened to the bolt proof load without thread stripping occurring. ) The property class of mating bolt shall be 10.9 or any other class that the assembly have the capability of being tightened to the bolt proof load without thread stripping occurring. ) Mating bolts shall have the same property class of nuts..7. Specification for hexagon nuts, style, Grades A and B shall be as given in Table and dimensions of required nuts "as specified in data sheet" shall comply with ISO 0. These nuts will be ordered with thread size of either M, M6, M8, M10, M1, M16, M0, M, M0 and M6. Dimensions of fine pitch thread, which may be ordered with thread size of either M8, M10, M1, M16, M0, M, M0 and M6, shall comply with ISO 867. Style 1 hexagon nuts are not in prime consider and shall only be supplied if ordered in special cases otherwise hexagon nuts of style shall be supplied. Non-preferred sizes given in the above mentioned standards shall not be supplied unless otherwise specified in data sheet. 0
TABLE - SPECIFICATION OF HEXAGON NUTS, STYLE GRADES A AND B MATERIAL 6g According to Clauses..1.and..1.and for fine pitch threads ISO 61, ISO 96 - Properties Acceptability Property class.6 1),.8 1), 8.8 ) ISO 898 part 1 A ISO 79 part 1 As processed Property class 8.8 bolts: (thermally or chemically) blackened. DIN 67 part shall apply with regard to surface roughness. ISO 617-1 and ISO 617- shall apply with regard to permissible surface discontinuities. ISO 0 shall apply with regard to electroplating. DIN 67 part 10 shall apply with regard to hot-dip galvanizing. ISO 69 shall apply with regard to the acceptance inspection. 1) The property class of mating bolt shall be 8.8 or any other class that the assembly have the capability of being tightened to the bolt proof load without thread stripping occurring. ) The property class of mating bolt shall be 1.9 or any other class that the assembly have the capability of being tightened to the bolt proof load without thread stripping occurring. ) The property class of mating bolt shall be 10.9 or any other class that the assembly have the capability of being tightened to the bolt proof load without thread stripping occurring. ) The property class of mating bolt shall be 1.9 or any other class that the assembly have the capability of being tightened to the bolt proof load without thread stripping occurring..7. Specification for hexagon nuts-grade C shall be as given in Table and dimensions of required nuts "as denoted in data-sheet" which may either be M, M6, M8, M10, M1, M16, M0, M, M0, M6, M, M8, M6 and M6 shall comply with ISO 0. Unless otherwise specified in data sheet the non-preferred thread size with related dimensions shall not be supplied. TABLE - SPECIFICATION FOR HEXAGON NUTS-GRADE C Properties MATERIAL Property class 7H According to Clauses..1. and..1. d M16: 1) M16 < d M9: 1), (in accordance with data sheet) d > M9 :as agreed or as denoted in data sheet d M9 :see subclause.7 d > M9: as agreed C ISO 769/1 As processed Requirements for electroplating are covered in ISO 0. Acceptability Acceptance procedure, shall be in accordance with ISO 69. 1) The property class of mating bolt shall be.6 or any other class that the assembly have the capability of being tightened to the bolt proof load without thread stripping occurring.7. Hexagon nuts with flange - Grade A Specification for these nuts which may be ordered with thread size of either M, M6, M8, M10, M1, M16 and M0 shall comply with Table and dimensions of required nuts "as denoted in data sheet" shall be as given in ISO 161. 1
Properties TABLE - SPECIFICATION FOR HEXAGON NUTS WITH FLANGE-GRADE A MATERIAL STAINLESS Property class 6H According to Clauses..1. and..1. 8, 9, 10 and 1 1) A - 70 In accordance to data sheet ISO 06 See..1and.7 A ISO 769-1 As processed Plain Requirements for electroplating are covered in ISO 0. Acceptability Acceptance procedure, shall be in accordance with ISO 69. 1) For nuts with property classes of 8 or 9 the mating bolt shall have the property class of 8.8. For nuts with property class of 10 the mating bolt shall have the property class of 10.9. For nuts with property class of 1 the mating bolt shall have the property class of 1.9. Instead of above mentioned property classes any bolts with any property class may be supplied " if required" but the assembly shall have the capability of being tightened to the bolt proof load without thread stripping occurring..7. Hexagon thin nuts (chamfered) - Grades A and B Specification for these nuts which may be ordered with thread size of either M1.6, M, M., M, M, M, M6, M8, M10, M1, M16, M0, M, M0, M6, M, M8, M6, M6 shall be as given in Table 6 and the dimensions of required nuts "denoted in data sheet" shall comply with ISO 0. Non preferred sizes which are given in the above mentioned standard shall not be supplied "unless otherwise stated in data sheet".
TABLE 6 - SPECIFICATIONS OF HEXAGON THIN NUTS-GRADES A AND B MATERIAL STAINLESS NON-FERROUS METAL 6H In Accordance with..1. and..1.. Properties Property class d < M: 1H M d M9: 0 1), 0 1) d > M9 as agreed or denoted in data sheet d < M:ISO 898/ M d M9: ISO 898/ d > M9: as agreed or denoted in data sheet d M0: A-70 ) M0 < d M9: A-0 d > M9: as agreed or denoted in data sheet d M9 : ISO 06 d > M9: as agreed or denoted in data sheet ISO 889 d M16: A d > M16 : B ISO 79 /1 As processed Plain Plain Requirements for electroplating are covered in ISO 0 Acceptability Acceptance procedure shall be in accordance with ISO 69 1) The property class of mating bolts shall be 6.8 but however the assembly of bolts and nuts shall have the capability of being tightened to mating bolt proof load without thread stripping occurring. ) Mating bolts shall have the same property class of nuts..7.6 Hexagon nuts for fine mechanics - Grade F Specification for these nuts "which may be ordered with thread diameters of either M1, M1., and M1. shall be as given in Table 7 and dimensions of required nuts "denoted in data sheet" shall comply with ISO 166. Properties TABLE 7 - SPECIFICATION FOR HEXAGON NUTS - GRADE F MATERIAL STAINLESS H Property class According to Clauses..1. and..1. or ISO 61and ISO 96 11 H 1 H (Steel min.110 HV) (Steel min.10 HV) ISO 898/ F ISO 769-1 Plain Requirements for electroplating are covered in ISO 0. Acceptability Acceptance procedure, shall be in accordance with ISO 69. A1 A (In accordance with data sheet) ISO 06.7.7 Hexagon nuts for structural bolting - Property Classes, 6 & 8 Specifications of these nuts "which may be ordered with thread size of either M10, M1, M16, M0, M, M0 and M6 shall be as given in Table 8 and dimensions of required nuts "denoted in data sheet" shall comply with ISO 71.
TABLE 8 - SPECIFICATIONS OF HEXAGON NUTS FOR STRUCTURAL BOLTING WITH PROPERTY CLASSES AND 8 MATERIAL 6AX 1) ISO 61and annex of ISO 71 Properties Surface finish Property class Type ) - 8 In accordance with data sheet See..1and.7 Grade A up to M16, Grade B over M16 ISO 79/1 Hot - dip galvanized ISO161 Acceptability Acceptance procedure, shall be in accordance with ISO 69. 1) Proof load and proof stress values of these nuts shall comply with the clause of ISO 71. ) For nuts with property class of the mating bolts shall have the property class of.6. For nuts of 8 the mating bolts shall have the property class of 8.8 and/or any bolts with any property class which the assemblies have capability of being tightened to the bolt proof load without thread stripping occurring..7.8 Hexagon nuts for structural bolting - Grad A property Class 9 Specifications for these nuts "which may be ordered with thread diameters of either M10, M1 and M16 shall comply with Table 9 and dimensions of required nuts "as denoted in data sheet" shall be in accordance with ISO 717. TABLE 9 - SPECIFICATION OF HEXAGON NUTS FOR STRUCTURAL BOLTING GRADE A AND PROPERTY CLASS 9 Properties Surface finish MATERIAL Property class Type 6AX 1) ISO 61and annex of ISO 71 9 ) See..1and.7 A ISO 79/1 Hot - dip galvanized ISO161 Acceptability Acceptance procedure, shall be in accordance with ISO 69. 1) Proof load stress shall in accordance with Clause of ISO 717. ) The property class of mating bolts shall be 8.8 or any bolt which the assembly shall have the capability of being tightened to the bolt proof load without thread stripping occurring..7.9 Hexagon nuts for high-strength structural bolting with large width across flats Grade B property classes 8 and 10 Specifications for these nuts which may be ordered with thread sizes of either M16, M0, M, M0 and M6 shall comply with Table 60 and dimensions of required nuts "as denoted in data sheet" shall be in accordance with ISO 77. Nuts with thread sizes of M1, M, M7 with related dimensions are not preferred but shall be supplied if required.
TABLE 60 - SPECIFICATIONS OF HEXAGON NUTS FOR HIGH STRENGTH STRUCTURAL BOLTING WITH LARGE WIDTH ACROSS FLATS MATERIAL 6H or 6AX According to..1. and..1.and Annex A of ISO 77 Property class 1) ) 8 or 101, Properties According to..1and.7 Surface finish Normal Optional (In accordance with data sheet) ) Black oxide Zinc electroplated, ) Cadmium electroplated ) Hot-dip galvanized to ISO 161 B except nut height m and c ) ISO 79/1 Acceptability For acceptance procedure, see ISO 69 Acceptability ISO 711 or ISO 71 Acceptability ISO 71 or ISO 716 1) For proof load values, see clause 6 of ISO 77. For nuts of 8, mating bolts shall have the property class of 8.8 and for nuts of 10, mating bolts shall have the property class of 10.9 but however any bolt with any property class may be mated provided that the assembly shall have the capability of being tightened to the bolt proof load without thread stripping occurring. ) Precautions to avoid hydrogen embrittlement may be necessary for property class 10. ) Black oxide means the normal finish resulting from manufacture with a light coating of oil. ) Except tolerance on perpendicularity of bearing face. ) For fasteners with zinc electroplated or hot-dip galvanized coatings the manufacturer shall apply a suitable lubricant coating on the nuts or on the mating bolts to ensure that seizure shall not take place in assembly. Information on a suitable test for the effectiveness of the lubricant coating given in annex B of ISO 77..7.10 Hexagon nuts for structural bolting with large width across flats Grade B - property Class 10 Specifications for these nut "which may be ordered with thread sizes of either M16, M0, M, M0 and M6 shall comply with Table 61 and dimensions of required nuts "as denoted in data sheet" shall be in accordance with ISO 71. Nuts with thread sizes of M1, M and/or M7 with related dimensions are not preferred but shall be supplied if required.
TABLE 61 - SPECIFICATION OF HEXAGON NUTS FOR STRUCTURAL BOLTING WITH LARGE WIDTH ACROSS FLATS - GRADE B Properties Surface finish MATERIAL Property class Normal Optional 6H or 6AX According to..1. and..1.and Annex A of ISO 71 10 1) See..1and.7 ) Black oxide Zinc electroplated ) Cadmium electroplated ) Hot-dip galvanized to ISO 161 B ISO 79/1 Acceptability For acceptance procedure, see ISO 69 Acceptability ISO 711 or ISO 71 Acceptability ISO 71 or ISO 716 ) Notes: 1) For proof load values, see clause 6 of ISO 71. The property class of mating bolts shall be 10.9 or bolts with any property class which the assembly shall have the capability of being tightened to the bolt proof load without thread stripping occurring. ) Black oxide means the normal finish resulting from manufacture with a light coating of oil. ) Precautions to avoid hydrogen embrittlement may be necessary for property Class 10. ) Except tolerance of perpendicularity of bearing surface..7.11 Specification for prevailing torque type all-metal hexagon nuts Style 1 of these nuts may be ordered with property class of either,8 or 10 (in accordance with data sheet). Dimensions of style 1 nuts which may be ordered with thread size of either M, M6, M8, M10, M1, M16, M0, M, M0 and M6 shall comply with ISO 7719. Style of these nuts shall be of property class 9 and Dimensions of Style nuts which may be ordered with thread size of either M, M6, M8, M10, M1, M16, M0, M, M0 and M6 shall comply with ISO 770, normal friction Type (NF) 1) or low friction Type (LF) ) of nuts may be required in both styles. Other specifications of prevailing torque type hexagon nuts shall be as given in Table 6. Notes: 1) Normal friction nuts usually have zinc electroplated finish plus a chromate or phosphate conversion coating with or without supplementary lubricants to meet the torque tension requirements. ) Low friction nuts usually have a finish which is either cadmium electroplated with a supplementary EP (Extreme Pressure) lubricant, or phosphate coated (zinc or manganese) with a rust preventive oil containing an EP lubricant to meet the torque tension requirements. 6
TABLE 6 - SPECIFICATION FOR PREVAILING TORQUE TYPE MATERIAL Property class ALL METAL HEXAGON NUTS Properties Torque and other reference requirements See sub-clause.7 6H According to..1. and..1. 1), 8, 9,10 (In accordance with data sheet) See Table 1 For d M16 : A - For d > M16 : B ISO 79/1 As processed Requirements for electroplated coating are covered in ISO 0 Acceptability Acceptance procedure shall be in accordance with ISO 69 1) Property class of mating bolts for nuts of shall be.6, for nuts of 8 and 9 shall be 8.8 and for nuts of 10 shall be 10.9 but however the assembly shall have the capability of being tightened to the proof load without thread stripping occurring..7.1 Specification for prevailing torque type all-metal hexagon nuts with flange which may be ordered with thread size of either M, M6, M8, M10, M1, M16 and M0 shall comply with Table 6. Dimensions of these nuts shall be in accordance with ISO 70. TABLE 6 - SPECIFICATION FOR PREVAILING TORQUE TYPE ALL-METAL HEXAGON NUTS WITH FLANGE Nuts Types Reference NF (Normal Friction) and LF (Low Friction) See..11 Material According to Relevant Requirements on..1 and.6 6H According to..1. and..1. 1) M16) Property class 8, 9,10,1 ( Properties See Table 0 See sub-clause.7 Torque and other reference requirements 1) A ISO 79/1 As processed Requirements for electroplated coating are covered in ISO 0 Acceptability Acceptance procedure shall be in accordance with ISO 69 Note: 1) Property class of mating bolts shall be such that the failure of assembly due to over tightening occur as bolt shank fracture rather than thread stripping..7.1 Specification for prevailing torque type nuts with non- metallic insert Style 1 of these nuts may be ordered with thread size of either M, M, M, M6, M8, M1, M16, M0, M, M0 and M6. Property class of either or 8 or 10 in accordance with data sheet. Dimensions of style 1 nuts shall comply with ISO 700. Style of these nuts may be ordered with 7
thread size of M, M6, M8, M10, M1, M16, M0, M, M0 or M6 and property class of either 9 or 1 and Dimensions of style nuts shall comply with ISO 701. Normal friction type (NF) or low friction type (LF) of nuts may be required in both styles. Other specifications of prevailing torque type nuts with non-metallic insert shall be as given in Table 6. Nuts Material TABLE 6 - SPECIFICATION FOR PREVILING TORQUE TYPE NUTS Types Reference Nut body Reference Insert Reference WITH NON-METALLIC INSERT NF (Normal Friction) and LF (Low Friction) (According to data sheet) See.6.11 Steel See.7 and Tables 0 and 1 Polyamid"Unless otherwise specified" ISO 0 6H According to..1. and..1. 1) 8, 9,10 (According to data sheet) See Table Property class Properties 1 See.7 Torque and other reference requirements A ISO 79/1 As processed Requirements for electroplated coating are covered in ISO 0 Acceptability Acceptance procedure shall be in accordance with ISO 69 1) Property class of mating bolts shall be such that the failure of assembly to overtightening occur as bolt shank fracture rather than thread stripping..7.1 Specification for prevailing torque type hexagon nuts with flange (with non-metallic insert) Dimensions of these nuts which may be ordered with thread size of either M, M6, M8, M10, M1, M16 and M0 shall be in accordance with ISO 70 and the other specifications shall comply with Table 6. 8
Nuts TABLE 6 - SPECIFICATION FOR PREVAILING TORQUE TYPE HEXAGON NUTS WITH FLANGE (WITH NON-METALLIC INSERT) Material Types Reference Nut body Reference Insert international standard NF (Normal Friction) and LF (Low Friction) (According to data sheet) See.6.11 Steel See.7 and Tables 0 and 1 Polyamid"Unless otherwise specified" ISO 0 6H According to..1. and..1. 1) 8, 9,10 (According to data sheet) See Table international standard Property class Properties 1 See.7 Torque and other reference requirements A ISO 79/1 As processed Requirements for electroplated coating are covered in ISO 0 Acceptability Acceptance procedure shall be in accordance with ISO 69 1) Property class of mating bolts shall be such that the failure of assembly due to overtightening occur as bolt shank fracture rather than thread stripping..7.1 Square nuts of grade C which may be ordered with thread size of either M, M6, M8, M10, M1, M16 and M0 shall comply with DIN 7..7.16 Square thin nuts of grade B which may be ordered with thread size of either M1.6, M, M., M, M, M, M8 or M10 shall comply with DIN 6..7.17 Square weld nuts which may be ordered with thread size of either M, M, M6, M8, M10, M1, M1, or M16 shall comply with DIN 98..7.18 Hexagon slotted nuts and castle nuts with metric coarse and fine pitch thread of grades A and B which may be ordered with thread size of either M, M, M6, M8, M10, M1, M16, M0, M, M0, M6, M, M8, M6, M6, M80, M90 and M100 shall comply with DIN 9 Part 1..7.19 Hexagon slotted nuts with metric coarse pitch thread of grade C which may be ordered with thread size of either M1, M16, M0, M, and M0 shall comply with DIN 9 Part..7.0 Hexagon weld nuts which may be ordered with thread size of either M, M, M, M6, M7, M8, M10, M1, M1 and M16 shall comply with DIN 99..7.1 Wing nuts which may be ordered with thread size of either M, M, M6, M8, M10, M1, M16, M0 and M shall comply with DIN 1..7. Slotted round nuts which may be ordered with thread size of either M1, M1., M1., M1.6, M, M., M, M, M, M6, M8, M10, M1, M16 and M0 shall comply with DIN 6..7. Round nuts with drilled holes in one face which may be ordered with thread size of either M, M., M, M, M, M6, M8 and M10 shall comply with DIN 7..7. Round nuts with set pin holes in side which may be ordered with threads sizes of M, M., M, M, M, M6, M8 and M10 shall comply with DIN 8..7. Self locking counter nuts which may be ordered with thread size of either M, M, M6, M8, M10, M1, M1, M16, M18, M0, M, M, M, M7, M0, M, M6, M9, M, M, M8 and 9
M shall comply with DIN 7967..8 Specific Requirements for Washers.8.1 Requirements for non percised washers. Non percised washers at least shall have the following specifications..8.1.1 The clearance holes of washers for specified bolts, screws and studs "if required" shall conform with the following Table and if desired sery is not mentioned the values given in medium sery shall be applicable. THREAD DIAMETER D 1.6 1.8.0..0..0..0 6.0 7.0 8.0 10.0 1.0 1.0 16.0 18.0 0.0.0.0 7.0 0.0.0 6.0 9.0.0.0 8.0.0 6.0 60.0 6.0 68.0 CLEARANCE d n 1.8.1..9..9..0. 6.6 7.6 9.0 11.0 1. 1. 17. 0.0.0.0 6.0 0.0.0 6.0 9.0.0.0 8.0.0 6.0 6.0 66.0 70.0 7.0.8.1. The outside diameter of washers shall comply with data-sheet which is selected from the following series in mm;.6,,.6,,.,, 6, 7, 8, 9, 10, 11, 1, 1, 1, 16, 18, 0,,, 8, 0,, 7, 9,, 0, 6, 60, 66, 7, 78, 80, 8, 9 and 98..8.1. The thicknesses of washers shall comply with data-sheet which is selected from the following series in mm; 0., 0., 0.8, 1, 1., 1.6,,.,,,, 6, 8, 10, 1, 1, 16, 18..8.1. for washers shall be in accordance with Table 66. 60
TABLE 66 - TOLERANCES FOR WASHERS Clearence holes FEUTURE TOLERANCES A D mm 1 C D 1 mm Tol. H 1 H 1 H 1 H 1 Mm mm mm mm 0.s min 0.s max 0.s min 0.s max Mm D Tol. D Tol. mm 0. 0. 1 B1 1) B1 Tol. mm ± 0.0 ± 0.1 mm B16 Tol. Mm 1.. 6 6 10 10 0 ± 0. ± 0. ± 0.6 ± 1 ± 1. 1 1.. 6 6 10 10 0 ± 0. ± 0. ± 0.6 ± 1 ± 1. ± 1.6 Chamfer a 0 to o emin =0.s emax =0.s 1) See ISO 86 61
Table 66 (continued) Tolerences for form and position Parallelism FEUTURE Note : The tolerence for parallelism is valid if the washeris In first position. A mm 0. 0. 1 1.. 6 6 10 10 0 0. 0.0 0.1 0.1 0. 0. 0. TOLERANCES C mm mm 1 1.. 6 6 10 10 0 0. 0. 0. 0. 0.6 1 mm Concentricity (coasiality) D 1 mm 0 0 b D mm 1T 1 1) 1 T 1 1) 0 0 B 1 T 1 1 T 16 Note : Tolerece based on dimension d Flatness Note : Tolerence C alwaysindipendent of thickness Tolerence for s. S mm 0. 0. 1 1.. 6 6 10 10 0 0.1 0.1 0. 0. 0. 0.6 1 C ) S mm 1 1.. 6 6 10 10 0 C ) 0. 0. 0.8 1. 1.8 1) See ISO 86 ) For washers made from stainless steel the maximum permissible unflatness is Zc..8. Specification for normal series of plain washers - product Grade A Dimensions shall conform with Table 67 and other properties shall comply with Table 68. Washers with nominal size of and over may be chamfered "if required". Dimensions and other 6
properties of chamfered washers shall comply with Tables 67 and 68. (CHAMFERED WASHERS) TABLE 67 - DIMENSIONS OF PLAIN WASHERS - NORMAL SERIES - GRADE A NOMINAL SIZE (thread size, d) 1.6.. 6 8 10 1 1 16 0 0 6 CLEARANCE HOLE d 1 OUTSIDE DIAMETER d THICKNESS h nom.(max.) max. nom.(max.) min. nom. max. min. 1.7 1.8.7 0. 0. 0....7 0. 0. 0..7.8 6.7 0. 0. 0...8 7 6.6 0. 0. 0..7.88 8 7.6 0. 0. 0...8 9 8.6 0.8 0.9 0.7..8 10 9.6 1 1.1 0.9 6. 6.6 1 11.7 1.6 1.8 1. 8. 8.6 16 1.7 1.6 1.8 1. 10. 10.77 0 19.18. 1.8 1 1.7.8..7. 1 1.7 8 7.8..7. 17 17.7 0 9.8..7 1 1. 7 6.8..7..8..7 1 1.9 6.6..7 7 7.6 66 6.8.6. properties TABLE 68 - PROPERTIES OF PLAIN WASHERS - NORMAL SERIES - GRADE A MATERIAL AUSTENITIC STAINLESS A 10 A 00 A 0 Classes 10 HV 00 HV 00 HV Reference In accordance with data sheet Hardness HV 1) 10 min. 00-00 00-00 A According to Table 66 Surface finish Plain, debarred Requirements for electroplating are given in ISO 16, ISO 17, ISO 18, and ISO 081 Acceptability The acceptance procedure, shall be in accordance with ISO 69 1) Vickers hardness..8. Specification for normal series of plain washers - product Grade C 10 min. 00 00 00 00 Dimensions shall comply with Table 69 and other properties shall be in accordance with Table 70. 6
TABLE 69 - DIMENSIONS OF PLAIN WASHERS - NORMAL SERIES - GRADE C NOMINAL SIZE (thread size, d) 6 8 10 1 1 16 0 0 6 CLEARANCE HOLE d 1 OUTSIDE DIAMETER d THICKNESS h nom.(max.) max. nom.(max.) min. nom. max. min. 6.6 6.8 10 9.1 1 1. 0.8 6.8 6.98 1 10.9 1.6 1.9 1. 9 9.6 18 1.9 1.6 1.9 1. 11 11. 0 18.7. 1.7 1.6 1.9.7..8. 16.6 16.9 8 6.7..8. 17.6 17.9 0 8.7.6..6 7 6..6. 8 8.6..6..6 6.1.6. 9 0 66 6.1 6 Properties TABLE 70 - PROPERTIES OF PLAIN WASHERS - NORMAL SERIES - GRADE C MATERIAL Class Hardness HV 100 HV 100 min C According to Table 66 Surface finish Plain Requirements for electroplating are given in ISO 16, ISO 17, ISO 18, and ISO 081 Hot dip galvanizing shall be in accordance with ISO 161 Acceptability The acceptance procedure, shall be in accordance with ISO 69.8. Specification for small series of plain washers product Grade A Dimensions shall comply with Table 71 and other properties shall comply with Table 7. 6
TABLE 71 - DIMENSIONS OF PLAIN WASHER - SMALL SERIES - PRODUCT GRADE A NOMINAL SIZE (thread size, d) 1.6.. 6 8 10 1 1 16 0 0 6 CLEARANCE HOLE d 1 OUTSIDE DIAMETER d THICKNESS h nom.(max.) max. nom.(max.) min. nom. max. min. 1.7 1.8.. 0. 0. 0..... 0. 0. 0..7.8.7 0. 0. 0...8 6.7 0. 0. 0..7.88 7 6.6 0. 0. 0...8 8 7.6 0. 0. 0...8 9 8.6 1 1.1 0.9 6. 6.6 11 10.7 1.6 1.8 1. 8. 8.6 1 1.7 1.6 1.8 1. 10. 10.77 18 17.7 1.6 1.8 1. 1 1.7 0 19.8. 1.8 1 1.7.8..7. 17 17.7 8 7.8..7. 1 1..8..7. 9 8.8..7 1 1. 0 9.8..7 7 7.6 60 8.8.6. 6
properties TABLE 7 - PROPERTIES OF PLAIN WASHERS - SMALL SERIES - PRODUCT GRADE A MATERIAL AUSTENITIC STAINLESS A 10 A 00 A 0 Classes 10 HV 00 HV 00 HV Reference In accordance with data sheet Hardness HV 10 min. 00-00 00-00 A According to Table 66 Surface finish Plain, debarred Requirements for electroplating are given in ISO 16, ISO 17, ISO 18, and ISO 081 Acceptability The acceptance procedure, shall be in accordance with ISO 69 10 min. 00 00 00 00.8. Specification for large series plain washers product grades A and C. The outside diameter of these washers shall be about times of their nominal size. Dimensions shall comply with Table 7. Other properties shall comply with Table 7. TABLE 7 - DIMENSIONS OF PLAIN WASHERS - LARGE SERIES PRODUCT GRADES A AND C NOMINAL SIZE (thread size, d). 6 8 10 1 1 16 0 0 6 CLEARANCE HOLE d 1 OUTSIDE DIAMETER d THICKNESS h nom.(max.) max. nom.(max.) min. nom. max. min...8 9 8.6 0.8 0.9 0.7.7.88 11 10.7 0.8 0.9 0.7..8 1 11.7 1 1.1 0.9..8 1 1.7 1. 1. 1 6. 6.6 18 17.7 1.6 1.8 1. 8. 8.6.8. 1.8 10. 10.77 0 9.8..7. 1 1.7 7 6.8..7 1 1.7.8..7 17 17.7 0 9.8..7 7. 60 8.1.6. 6 6.8 7 70.1 6 9 89.8 6 7 9 0 110 107.8 8 9. 6.8 66
TABLE 7 - PROPERTIES OF PLAIN WASHERS - LARGE SERIES PRODUCT GRADES A AND C MATERIAL AUSTENITIC STAINLESS A 10 Classes properties Hardness HV Grade A: 10 HV Grade C: 100 HV Grade A: 10 min. Grade C: 100 min. A for nominal sizes 16 C for nominal sizes >16 According to Table 66 10 min. A According to Table 66 Surface finish Plain Requirements for electroplating are given in ISO 16, ISO 17, ISO 18, and ISO 081 Acceptability The acceptance procedure, is given in ISO 69.8.6 Specification for extra large series plain washers - product Grade C Dimensions of extra large plain washers shall comply with Table 7 and other properties shall comply with Table 76. TABLE 7 - DIMENSIONS OF EXTRA LARGE PLAIN WASHERS NOMINAL SIZE (thread size, d) 6 8 10 1 1 16 0 0 6 CLEARANCE HOLE d 1 OUTSIDE DIAMETER d THICKNESS h nom.(max.) max. nom.(max.) min. nom. max. min.. 6.8 18 16.9. 1.7 6.6 6.96 0.7. 1.7 9 9.6 8 6.7.6. 11 11...6. 1. 1.9..6. 1. 1.9 0 8..6. 17. 18. 6.1 6.8 7 70.1 6 7 6 6.8 8 8.8 6 7 10 10.8 6 7 9 0 1 1. 8 9. 6.8 67
Properties TABLE 76 - PROPERTIES OF EXTRA LARGE PLAIN WASHERS MATERIAL Class Hardness HV 100 HV 100 min C According to Table 66 Surface finish Plain Requirements for electroplating are given in ISO 16, ISO 17, ISO 18, and ISO 081 Hot dip galvanizing shall be in accordance with ISO 161 Acceptability The acceptance procedure, shall be in accordance with ISO 69.8.7 Specifications for hardened and tempered plain washers for high-strength structural bolting This sery is supplied for assembly with large series hexagon high-strength structural bolts and nuts of M1 to M6 inclusive. Dimensions of these washers shall comply with Table 77 and the other properties shall comply with Table 78, these washers shall be marked or shaped in such a manner so as to differentiate them from other similar products. TABLE 77 - DIMENSIONS OF PLAIN WASHERS FOR HIGH-STRENGTH STRUCTURAL BOLTING THREAD SIZE, d, OF ASSOCIATED BOLT d 1 min. max. D min. max. h min. max. M1 M16 M0 M M0 M6 1 1..7 7.1.6 18 18...1.6. 0..1.6 6 6. 8. 0..6.6 8.1 60..6 9 9.6 70.1 7..6 68
TABLE 78 - PROPERTIES OF PLAIN WASHERS FOR HIGH STRENGTH STRUCTURAL BOLTING MATERIAL Hardness, Properties range (HRC) 1) d 1 : A : h : IT 16 when d M0 d : C : h : IT 17 when d > M0 Shall be in accordance with Table 66 Surface finish Black oxide ) or zinc electroplated ) cadmium electroplated ) hot dip galvanized ) "as data sheet, if not specified the surface finish shall be black oxide. Acceptability Nuts mentioned in.7.9 1) Minimum hardness for hot dip galvanized washers may be 6 HRC. ) Black oxide means the normal finish resulting from heat treatment with a residual coating of light oil. ) Precautions to avoid hydrogen embrittlement is necessary..8.8 Specification for hardened and tempered chamfered plain washers for high-strength structural bolting This sery like as the washers mentioned in sub-subclause.8.7 is supplied to be assembled with large hexagon highstrength structural bolts and nuts of M1 to M6 inclusive. Dimensions of these washers shall comply with Table 79 and the other properties shall be in accordance with Table 80. 69
TABLE 79 - DIMENSIONS OF CHAMFERED PLAIN WASHERS FOR HIGH-STRENGTH STRUCTURAL BOLTING THREAD SIZE, d, OF ASSOCIATED BOLT M1 M16 M0 M M0 M6 d 1 min. max. 1 1. 17 17.7 1 1.. 1 1.6 7 7.6 D min. max..7 1. 8. 0. 7.1 6 6.1 66 h min. max...6..6..6..6..6..6 E 0. 1 1 1 1 1 c min. max 1. 1.6 1. 1.6 1.6.0 1.6.0.0.6..8 TABLE 80 - PROPERTIES OF CHAMFERED PLAIN WASHERS FOR HIGH-STRENGTH STRUCTURAL BOLTING MATERIAL Hardness, Properties range (HRC) 1) d1 : d : C : h : Shall be in accordance with Table 66 IT 17 1) Surface finish Normal Optional Black oxide ) or Zinc electroplated ) or cadmium electroplated ) or hot dip galvanized ) "as data sheet" and if not specified in data sheet the surface finish shall be black oxide Associated bolts "if required" See... / ISO 711 and ISO 71 Associated nuts "if required" Nuts mentioned in.7.9 and.7.10 or ISO 77 and ISO 71 1) Minimum hardness for hot-dip galvanized washers may be 6 HRC. ) Black oxide means the normal finish resulting from heat treatment with a light coating of oil. ) Precautions to avoid hydrogen embrittlement may be necessary. - See ISO 86 70
.8.9 Tab washers with long tap shall comply with DIN 9..8.10 Curved and wave spring lock washers shall conform with DIN 18..8.11 Curved and wave spring washers shall comply with DIN 17..8.1 External tab washers (locking tab washers) shall comply with DIN..8.1 Tab washers with long and short tap at right angles shall conform with DIN 6..8.1 Conical spring washers which are used for bolt/nut assemblies shall conform with DIN 6796..8.1 Toothed lock washers shall comply with DIN 6797..8.16 Serrated lock washers shall comply with DIN 6798..8.17 Spring lock washers with safety ring shall comply with DIN 691..8.18 Curved spring washers shall comply with DIN 690..8.19 Spring washers shall comply with DIN 690..8.0 Lock washers shall comply with DIN 6906. 6. MARKING Marking shall be as below. Marking other than that mentioned in this Standard, is applicable by written permission of the Company. 6.1 Marking of bolts, screws and studs made of carbon steel or alloy steel with the exception of set screws and similar threaded fasteners not under tensile stresses. 6.1.1 Hexagon bolts and screws Hexagon bolts and screws shall be marked with the designation symbol of the property class. The marking is obligatory for all property classes, preferably on the top of the head by indenting or embossing or on the side of the head by indenting. Examples of marking on hexagon bolts and screws shown below: Marking is required for hexagon bolts and screws with nominal diameters d mm where the shape of the product allows it, preferably on the head. 6.1. Hexagon socket head cap screws Hexagon socket head cap screws shall be marked with the designation symbol of the property class. The marking is obligatory for all property classes preferably on the side of the head by indenting or on the top of the head by indenting or embossing. Examples of marking on hexagon socket head cap screws shown below: Marking is required for hexagon socket head cap screws with nominal diameters d mm where 71
the shape of the product allows it, preferably on the head. 6.1. Studs Studs shall be marked with the designation symbol of the property class. The marking is obligatory for property classes equal to or higher than 8.8, preferably on the extreme end of the threaded portion by indenting (see figure below). For studs with interference fit, the marking shall be at the nut end. Marking is required for studs with nominal diameters equal to or greater than mm. MARKING OF STUD The symbols in the below table are permissible as an non-preferred alternative identification method. IDENTIFICATION MARKS FOR STUDS 6.1. Marking of left - hand thread Bolts and screws with left-hand thread shall be marked with the symbol shown below, either on the top of the head or the point. LEFT-HAND THREAD MARKING Fig. 10 Marking is required for bolts and screws with nominal thread diameters d mm. Alternative marking for left-hand thread may be used for hexagon bolts and screws as shown below: 7
1) s is the width across flats. ) k is the height of the head. 6. Marking of Set Screws and Similar fasteners not under tensile stresses made of carbon steel or alloy steel. Unless otherwise specified marking of set screws are not obligatory. 6. Marking of Nuts with Specified Proof Load Values Made of Carbon Steel or Alloy Steel 6..1 Nuts shall be marked with: a) The property class indenting on the side or bearing surface, or by embossing on the chamfer. See figures below. Embossed marks shall not protrude beyond the bearing surface of the nut. b) The trade (identification) marking of the manufacturer is mandatory on all products covered by the obligatory marking requirements for property classes, provided this is possible for technical reasons. Packages, however, must be marked in any case. EXAMPLES OF MARKING WITH DESIGNATION SYMBOL EXAMPLES OF MARKING WITH CODE SYMBOL (CLOCK - FACE SYSTEM) 7
6.. Marking symbols for different property classes are shown in tables below: MARKING SYMBOLS FOR NUTS 6.. Marking of left - hand thread Nuts with left-hand thread shall be marked as shown below on one bearing surface of the nut by indenting. LEFT - HAND THREAD MARKING Marking is required for nuts with thread diameters 6 mm. Alternative marking for left-hand thread might be used as shown in figure below: ALTERNATIVE LEFT - HAND THREAD MARKING 6. Marking of Nuts with Specified Proof Load with Fine Pitch Made of Carbon Steel or Alloy Steel Nuts of M and larger shall be marked legibly to identify property class and manufacturer trade. Manufacturer s identification shall be at his option. Marking may be raised or indented at the 7