EcoSystem 5-Series LED Driver W to 75 W 369823d 1 11.17.14 EcoSystem 5-Series LED drivers provide a high performance solution for any space, in any application, while providing smooth, continuous dimming down to 5% of full output current. Features Continuous, flicker-free dimming from 100% to 5% 1. Guaranteed dimming performance when used with Lutron controls. Guaranteed compatibility with Energi Savr NodeTM units with EcoSystem, GRAFIK Eye QS with EcoSystem, PowPak dimming module with EcoSystem, and Quantum systems, allowing for integration into a planned or existing EcoSystem lighting control solution. Protected from miswires of input power to EcoSystem control inputs up to 277 V~. A rated lifetime of 50,000 hours at 75 C (167 F) calibration point (t c ). Type TL Rated. FCC Part compliant for commercial applications at 1 277 V ~. 100% performance tested at factory. RoHS compliant. Non-volatile memory restores all settings after power failure. For more information please visit: www.lutron.com/ecosystem5series EcoSystem LED Driver, case type M 1.18 in (30 mm) W x in ( mm) H x 14.13 in (359 mm) L EcoSystem Features Simpler to wire and more reliable than 0-10 V-. Guarantees compatibility between Lutron controls, drivers, and sensors. Accommodates zone changing without rewiring. Link to Lutron Quantum Total Light Management System to monitor lighting power consumption. 1 Light output at 5% depends on the efficacy of the light engine used with the driver.
Specifications 369823d 2 11.17.14 Regulatory Approvals Lutron Quality Systems registered to ISO 9001.08 Manufacturing facilities employ ESD reduction practices that comply with the requirements of ANSI / ESD S. Meets ANSI C62.41 category A surge protection standards up to and including 4 kv FCC Part compliant for commercial applications at 1 277 V~ Meets UL 8750, Light Emitting Diode (LED) Equipment for use in Lighting Products Type TL rated Class 2 output Meets LED driver requirements for Energy Star version 1.2 Performance Dimming Range: 100% to 5% 1 Operating : 1 277 V~ at 50 / 60 Hz Lifetime: 50,000 hours when calibration point (t c ) at 75 C (167 F) 2 For rated warranty, t c not to exceed 75 C (167 F) (maximum rated temperature) 2 Patented thermal foldback protection LED lighting turns on to any dimmed level without flashing to full brightness Non-volatile memory restores all driver settings after power failure Typical standby power consumption: 0.2 W at 1 V~ and 0.3 W at 277 V~ Open-circuit protected output Short-circuit and overload-protected output Device turn-on time: < 100 ms from electronic off and < 500 ms from power off Class 2 output designed to withstand hot swap Inrush current less than NEMA 410-11 limit Dimming method: constant-current reduction, refer to Lutron Application Note #360 for details Environmental Sound rated: Class A inaudible in 24 dba ambient Relative Humidity: maximum 90% non-condensing Minimum Operating Ambient Temperature: t a = 0 C (32 F) 3 Indoor use only Rated for dry and damp locations Driver Wiring and Mounting Driver is grounded by a mounting screw to the grounded fixture Terminal blocks on the driver accept one solid wire per terminal from 18 AWG to 16 AWG (0.75 mm 2 to 1.5 mm 2 ) Fixture must be grounded in accordance with local and national electrical codes Maximum driver-to-led light engine wire length for: Wire Gauge 0 ma to 700 ma Maximum Lead Length 710 ma to 1.50 A 1.51 A to 2.10 A 18 AWG (0.75 mm 2 ) 30 ft (9 m) ft (4.5 m) 10 ft (3 m) 16 AWG (1.5 mm 2 ) 35 ft (10.5 m) ft (7.5 m) ft (4.5 m) 14 AWG (2.5 mm 2 ) 50 ft ( m) 40 ft (12 m) ft (7.5 m) 12 AWG (4.0 mm 2 ) 100 ft (30 m) 60 ft (18 m) 40 ft (12 m) * To use wire gauges larger than the terminal blocks rated gauge of 18 to 16 AWG (0.75 mm 2 to 1.5 mm 2 ), refer to Terminal Wiring Gauges diagram. The 18 to 16 AWG (0.75 mm 2 to 1.5 mm 2 ) wires connected to the driver should be less than 3 ft (0.9 m). 1 Light output at 5% depends on the efficacy of the light engine used with the driver. 2 To maintain warranty, installer is responsible for ensuring that the driver calibration point does not exceed 75 ºC (167 ºF). 3 Where t a is the temperature of the air directly surrounding the driver.
369823d 3 11.17.14 How to Build a Model Number: EcoSystem 5-Series (up to 75 W) LED Driver LDE5_U1UMN-_ A Example: LDE53U1UMN-BA070 0.70 A, W to 28 W, 21.5 40 V- ** LED driver For further assistance selecting your model number, contact our LED Center of Excellence at LEDs@lutron.com LED Load Range Class 2 Constant Current B = 0.50 A to 1. A, 40 V- *, W to 35 W C = 0.88 A to 1.75 A, 40 V- *, W to 50 W D = 1. A to 2.10 A, 40 V- *, 35 W to 75 W T = 0.40 A to 0.83 A, 30 50 V- *, W to 35 W U = 0.70 A to 1.33 A, 30 50 V- *, W to 50 W V = A to 1.88 A, 30 50 V- *, 40 W to 75 W LED Load Power Range 3 = Use when LED Load Range is B or T 5 = Use when LED Load Range is C or U 7 = Use when LED Load Range is D or V Current Level (for Constant Current): 040 = 0.40 A:... 210 = 2.10 A Attention: Model numbers may appear similar to Lutron Hi-lume A-Series drivers, but EcoSystem 5-Series drivers are not a direct model-for-model replacement for Hi-lume A-Series drivers. Please note the driver s output rating and the load ratings to select the correct product for your fixture. * voltage range changes with output current and according to power limits. Check driver specifications on following pages carefully to understand output voltage range of a particular SKU. Purchaser is responsible for electrical compatibility between LED driver and LED load. ** Minimum voltage of LDE53U1UMN-BA070 limited by W minimum power.
B Range 369823d 4 11.17.14 Driver Type Dimming Method Current Power Standards Recognition Maximum Rated Temp. @ t c for Warranty Constant Current Driver (Class 2) Constant Current Reduction (CCR) 40 V- 0.50 1. A 35 W Type TL 84 º / 65 ºC 75 ºC Typical Performance Specifications: Parameter Value Test Conditions Input Current 0. A V i = 277 V, t a = C, I o = 0.88 A, V o = 40 V, Power Factor 0.96 Maximum Light THD % LDE53U1UMN-BA088 Driver Efficiency 85% 45 Load Compatibility & DLC Compliance 90 Efficiency vs Current 40 (V) 35 30 W 17.5 W 35 W DLC compliance region.50 0.35 0.70 1.05 1.40 1.75 0.00 0.35 0.50 0.70 1.05 1. 1.40 1.75 Current (A) Efficiency @ Pmax (%) 85 80 75 0.5 0.75 1. Current (A) THD vs Power Power Factor vs Power THD (%) 10 5 Power Factor 0.95 0.90 0 30 35 Power (W) 0.85 30 35 Power (W)
C Range 369823d 5 11.17.14 Driver Type Dimming Method Current Power Standards Recognition Maximum Rated Temp. @ t c for Warranty Constant Current Driver (Class 2) Constant Current Reduction (CCR) 40 V- 0.88 1.75 A 50 W Type TL 80 º / 76 ºC 75 ºC Typical Performance Specifications: Parameter Value Test Conditions Input Current 0.21 A V i = 277 V, t a = C, I o = 1. A, V o = 40 V, Power Factor 0.97 Maximum Light THD 13% LDE55U1UMN-CA1 Driver Efficiency 88% 45 Load Compatibility & DLC Compliance 90 Efficiency vs Current 40 (V) 35 30 W 50 W DLC compliance region.50 0.70 0.90 1.10 1.30 1.50 0.00 0.70 0.88 1.05 1.40 1.75 2.10 Current (A) Efficiency @ Pmax (%) 85 80 75 0.85 1. 1.45 1.75 Current (A) THD vs Power Power Factor vs Power THD (%) 10 5 Power Factor 0.95 0.90 0 30 35 40 45 50 Power (W) 0.85 30 35 40 45 50 Power (W)
D Range 369823d 6 11.17.14 Driver Type Dimming Method Current Power Standards Recognition Maximum Rated Temp. @ t c for Warranty Constant Current Driver (Class 2) Constant Current Reduction (CCR) 40 V- 1. 2.10 A 35 75 W Type TL 82 º / 82 ºC 75 ºC Typical Performance Specifications: Parameter Value Test Conditions Input Current 0.31 A V i = 277 V, t a = C, I o = 1.88 A, V o = 40 V, Power Factor 0.95 Maximum Light THD 13% LDE57U1UMN-DA188 Driver Efficiency 89% 45 Load Compatibility & DLC Compliance 90 Efficiency vs Current (V) 40 35 30 See C Range for DLC compliant options in this region 35 W 37.5 W 75 W DLC compliance region.70 1.05 1.40 1.75 2.10 2.45 0.70 1.05 1. 1.40 1.75 2.10 2.45 Current (A) Efficiency @ Pmax (%) 85 80 75 1. 1.50 1.75 2.00 2.10 Current (A) THD vs Power Power Factor vs Power THD (%) 10 5 Power Factor 0.95 0.90 0 35 40 45 50 55 60 65 70 75 Power (W) 0.85 35 40 45 50 55 60 65 70 75 Power (W)
T Range 369823d 7 11.17.14 Driver Type Constant Current Driver (Class 2) Dimming Method Constant Current Reduction (CCR) Current Power Standards Recognition 30 50 V- 0.40 0.83 A 35 W Type TL pending 75 ºC Maximum Rated Temp. @ t c for Warranty Typical Performance Specifications: Parameter Value Test Conditions Input Current 0. A V i = 277 V, t a = C, I o = 0.70 A, V o = 50 V, Power Factor 0.97 Maximum Light THD % LDE53U1UMN-TA070 Driver Efficiency 86% 55 Load Compatibility & DLC Compliance 90 Efficiency vs. Current 50 (V) 45 40 35 30 DLC compliance region.00 0.00 0. 0.50 0.50 0.75 0.75 1. 1. Current (A) Efficiency at Pmax (%) 85 80 75 0.40 0.53 0.67 0.80 0.83 Current (A) THD vs. Power Power Factor vs. Power THD (%) 10 Power Factor 0.95 0.90 5 0 17.5 22.5 27.5 30 32.5 35 Power (W) 0.85 17.5 22.5 27.5 30 32.5 35 Power (W)
U Range 369823d 8 11.17.14 Driver Type Constant Current Driver (Class 2) Dimming Method Constant Current Reduction (CCR) Current Power Standards Recognition 30 50 V- 0.70 1.33 A 50 W Type TL pending 75 ºC Maximum Rated Temp. @ t c for Warranty Typical Performance Specifications: Parameter Value Test Conditions Input Current 0.21 A V i = 277 V, t a = C, I o = 1.0 A, V o = 50 V, Power Factor 0.97 Maximum Light THD 11% LDE55U1UMN-UA100 Driver Efficiency 86% 55 Load Compatibility & DLC Compliance 90 Efficiency vs. Current 50 (V) 45 40 35 30 DLC compliance region. 0. 0.50 0.75 0.75 1. 1. 1.50 1.50 Current (A) Efficiency at Pmax (%) 85 80 75 0.70 0.90 1.10 1.30 1.33 Current (A) THD vs. Power Power Factor vs. Power THD (%) 10 Power Factor 0.95 0.90 5 0 28.1 31. 34.4 37.5 40.6 43.75 46.9 50 Power (W) 0.85 28.1 31. 34.4 37.5 40.6 43.75 46.9 50 Power (W)
V Range 369823d 9 11.17.14 Driver Type Constant Current Driver (Class 2) Dimming Method Constant Current Reduction (CCR) Current Power Standards Recognition 30 50 V- 1.88 A 40 75 W Type TL pending 75 ºC Maximum Rated Temp. @ t c for Warranty Typical Performance Specifications: Parameter Value Test Conditions Input Current 0.32 A V i = 277 V, t a = C, I o = 1.5 A, V o = 50 V, Power Factor 0.98 Maximum Light THD 13% LDE57U1UMN-VA0 Driver Efficiency 88% 55 Load Compatibility & DLC Compliance 90 Efficiency vs. Current 50 (V) 45 40 35 30 DLC compliance region.75 0.75 1. 1. 1.50 1.50 1.75 1.75 2.00 2.00 Current (A) Efficiency at Pmax (%) 85 80 75 1.50 1.75 1.75 1.88 Current (A) THD vs. Power Power Factor vs. Power THD (%) 10 Power Factor 0.95 0.90 5 0 40 44.4 48.75 53.1 57.5 61.9 66. 70.6 75 Power (W) 0.85 40 44.4 48.75 53.1 57.5 61.9 66. 70.6 75 Power (W)
M Case: Case Dimensions C 369823d 10 11.17.14 D B A A B C D 14.13 in (359 mm) 13.66 in (347 mm) (mounting center) 1.18 in (30 mm) in ( mm)
Terminal Wiring Gauges 369823d 11 11.17.14 N L Mains E1 E2 Digital Link Ground 1 18 AWG to 16 AWG (0.75 mm 2 to 1.5 mm 2 ) 18 AWG to 16 AWG (0.75 mm 2 to 1.5 mm 2 ) 18 AWG to 16 AWG (0.75 mm 2 to 1.5 mm 2 ) 18 AWG to 12 AWG (0.75 mm 2 to 4.0 mm 2 ) 18 AWG to 12 AWG (0.75 mm 2 to 4.0 mm 2 ) 18 AWG to 12 AWG (0.75 mm 2 to 4.0 mm 2 ) Wiring Diagram for EcoSystem Digital Control To Line Hot (Black) Neutral (White) EcoSystem 5-Series Ground 1 +V (Red) 2 V (Black) 2 LED Light Engine To EcoSystem Digital Link E1 (Purple) E2 (Purple-White) Note: Colors shown correspond to terminal blocks on driver. 1 Fixture and driver case must be grounded in accordance with local and national electrical codes; ground connection to driver must be accomplished through grounding the case. 2 For maximum driver-to-led light engine wire length, see charts in the Driver Wiring and Mounting section.
EcoSystem Wiring Diagrams EcoSystem Digital Link Overview The EcoSystem Digital Link wiring (E1 and E2) connects the digital ballasts and drivers together to form a lighting control system. Sensors do not connect directly to EcoSystem 5-Series LED drivers. Sensors are integrated through the EcoSystem controller. E1 and E2 (EcoSystem digital link wires) are polarity insensitive and can be wired in any topology. Power is supplied to the EcoSystem Digital Link from the control system. Driver Terminals N L E1 E2 Mains Digital Link 369823d 12 11.17.14 EcoSystem Digital Link Wiring EcoSystem Digital Link terminals accept only one 18 AWG to 16 AWG (0.75 mm 2 to 1.5 mm 2 ) solid copper wire per terminal. Make sure that the supply breaker to the drivers and EcoSystem Digital Link Supply is OFF when wiring. Connect the two conductors to the two driver terminals E1 and E2 as shown. Using two different colors for E1 and E2 will reduce confusion when wiring several drivers together. The EcoSystem Digital Link may be wired Class 1 or Class 2. Consult applicable electrical codes for proper wiring practices. For emergency wiring, please refer to Lutron Application Note #106. Notes Driver Terminals To the EcoSystem Digital Link Supply and additional drivers and/or ballasts The EcoSystem Digital Link Supply does not have to be located at the end of the Digital Link. EcoSystem Digital Link length is limited by the wire gauge used for E1 and E2 as follows: N L E1 E2 Mains Digital Link Wire Gauge Digital Link Length (max) 12 AWG* 20 ft 14 AWG* 1400 ft 16 AWG 900 ft 18 AWG 550 ft Wire Size Digital Link Length (max) 4.0 mm 2 * 828 m 2.5 mm 2 * 517 m 1.5 mm 2 310 m 1.0 mm 2 7 m 0.75 mm 2 5 m * To use wire gauges larger than the terminal blocks rated gauge of 18 AWG to 16 AWG (0.75 mm 2 to 1.5 mm 2 ), refer to Terminal Wiring Gauges diagram. The 18 AWG to 16 AWG (0.75 mm 2 to 1.5 mm 2 ) wires connected to the driver should be less than 3 ft (0.9 m).
Service 369823d 13 11.17.14 Warranty For warranty information, please visit www.lutron.com/ballastdriverwarranty Replacement Parts When ordering Lutron replacement parts, please provide the full model number. Consult Lutron if you have any questions. Further Information For further information, please visit us at www.lutron.com/ecosystem5series or contact our LED Control Center of Excellence at 1.877.346.5338 or LEDs@lutron.com