SARGENT 1331 DOOR CLOSER INSTALLATION INSTRUCTIONS WITH JUH (HOLD OPEN) ARMS Strength Adjustable From Size 1 Thru 6 CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE. FOR ASSISTANCE, CALL SARGENT AT 1800727477 or www.sargentlock.com Choose From 1 of the 3 Applications Below JH Standard Arm JPH9 Parallel Arm JH Top Jamb Arm Use Standard & Parallel Full Size Templates Provided OR Predrill 3/32 holes for self tapping screws or #16 drill for #1224 tap for machine screws NOTE: With swing clear hinges, use data sheets provided. * 1/4" Variance allowed for retrofit of existing closers With fasteners provided, secure closer body to door with power adjustment away from hinge. Using optional mortise nuts when throughbolting Frame Door stop Mortisenut nut Power Adjustment D f Drill 1/4" dia. hole for Dia. screws hole Drill 3/8" Dia dia. hole for formortise nut body nut body Unreinforced door door Copyright 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited. 1
1331 STANDARD APPLICATION JH HOLD OPEN ARM INSTRUCTIONS 1 Determine maximum degree of door opening required. Use a #16 drill. Drill and tap door and frame for 1224 machine screws. When using the included self tapping screw, predrill with a 3/32" drill. *Provides maximum power for heavy or drafty doors *(120 12 ) 180 101/8" 2 1/2" 1" *(120 612") 180 4/8" 3/4" 13/8" 12" 2 Right hand shown, left hand similar. With provided fasteners, install foot to frame and secure closer body to door with power adjustment away from hinge Nut faces up Frame Frame Right hand door shown Nut faces down Left hand door shown Power adjustment 3 On both right and left hand doors, secure main arm to top spindle with screw and washer provided. Align flat mark as shown Flat mark 4 Open door and insert foot into main arm. Close door fully, and while pushing arm as shown in picture, tighten arm bolt See page for closer adjustment and cover installation. Arm Bolt 90 2 Copyright 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
1 1331 JPH9 PARALLEL HOLD OPEN INSTRUCTIONS Determine maximum degree of door opening required. Use a #16 drill. Drill and tap door and frame for 1224 machine screws. When using the included self tapping screws, predrill with a 3/32" drill. *Provides maximum power for heavy or drafty doors 31/2" Center line of hinge 3/4" 12" 2 3 Right hand shown, left hand opposite. With fasteners provided, install foot to frame with nut as shown and closer body to door with power adjustment toward hinge Center line of hinge IMPORTANT Nut faces down for left hand and faces up for right hand door Frame Door Cover Use 1331D Drop bracket if door rail is too narrow 1/2" 21/2" *(120 33/4") 180 13/8" *(120 91/2") 180 71/8" /8" 11/4" 17/8" Center line of hinge 4 Left Hand Door Flat mark Right Hand Door With wrench on bottom spindle, preload/index by turning spindle as shown and secure main arm to top spindle with flat mark as indicated at left with screw and washer Open door and insert foot into main arm. Close door fully, while holding elbow 11/4" from door. Tighten arm bolt 11/4" Arm bolt See page for adjustment and cover installation Drop Plate 21/2" Min. 1331D Drop plate used when top rail is less than 2 1/2" Accessory Information 811 Blade Stop Spacer Kit Metal spacer for use on 1/2" blade stops on aluminum store fronts Copyright 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited. 3
1331 JH TOP JAMB PARALLEL HOLD OPEN INSTRUCTIONS 1 Determine maximum degree of door opening required. Use a #16 drill. Drill and tap door and frame for 1224 machine screws. When using provided self tapping screws, predrill with a 3/32" drill. *Provides maximum power for heavy or drafty doors Center line of hinge *(120 63/4") 3/4" 12" 180 4/8" 1/2" 21/2" 21/4" Right hand door shown, left hand door similar 2 *(120 123/8") 180 101/8" With provided fasteners, install foot to door as shown and closer body to frame with power adjustment away from hinge Hinge edge Nut faces up 3 Power Adjustment Left hand door shown Nut faces down Right hand door shown On both right and left hand doors, secure main arm to spindle with screw and washer provided. Align flat mark as shown Flat mark 4 Open door and insert foot into main arm. Close door fully, and while pushing arm as shown in picture, tighten arm bolt Accessories Arm Bolt 90 4 See page for adjustment and cover installation Copyright 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
CLOSER ADJUSTMENT AND COVER INSTALLATION THE 1331 IS FACTORY ADJUSTED FOR MOST APPLICATIONS, HOWEVER, ADDITIONAL ADJUSTMENT MAY BE REQUIRED DUE TO ACTUAL CONDITIONS MINIMUM RECOMMENDED DOOR CLOSING TIME FOR DOORS OPENED TO 90 IS 6 SECONDS. Use 1/8" hex (Allen) wrench to adjust valves as needed. SWEEP AND LATCHING SPEEDS: Turn valves clockwise to slow down or counterclockwise to speed up door movement BACKCHECK: To regulate the intensity of backcheck action, turn valve clockwise to increase or counterclockwise to decrease checking CAUTION: SET VALVE FOR SLIGHT CUSHIONING EFFECT. CLOSER CAN BE DAMAGED IF THE CHECKING ACTION IS TOO ABRUPT. NEVER USE THE BACKCHECK AS A DOOR STOP. ALWAYS USE A DOOR STOP TO STOP THE DOOR IF ADJUSTMENTS ARE INEFFECTIVE, CHECK INDEXING AS SHOWN IN STEP 3 AND CHECK FOR CORRECT TEMPLATING Speed up Slow down Spring power adjustment 1/8" 1/8" HEX wrench Latching speed range Sweep (Closing) speed range Backcheck range CLOSING POWER: Sweep Certain applications may require closing power adjustment: If the door will not latch properly, increase power by turning the power adjustment clockwise in full turn increments. If the door is hard to open, reduce power by turning the power adjustment counterclockwise in full turn increments. Backcheck Latch 6 COVER INSTALLATION Move insert if needed. Install cover with two #6 32 X /16" machine screws as shown. Insert 7 ADJUSTMENT HOLD OPEN ARM Slight tightening or loosening of hold open nut changes holding position of door. NOTE: To protect wall, trim and closer, use a door stop located beyond hold open positions, but not beyond the max. door opening shown on instructions. Hold open nut Use 1/16" wrench to adjust nut Copyright 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
6 Copyright 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
Copyright 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited. 7
8 Copyright 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.