GmbH Mathildenstr. 10A 82319 Starnberg Germany SM 10/4/2014 1/12 GmbH www.freltec.com
SM SPECIFICATION 603 1SM5927x SMx E03 Type Type Package Packing 603: ZENER DIODE 1SM5913x 1SM5914x 1SM5915x 1SM5916x 1SM5917x 1SM5918x 1SM5919x 1SM5920x 1SM5921x 1SM5922x 1SM5923x 1SM5924x 1SM5925x 1SM5926x 1SM5927x 1SM5928x 1SM5929x 1SM5930x 1SM5931x 1SM5932x 1SM5933x 1SM5934x 1SM5935x 1SM5936x 1SM5937x 1SM5938x 1SM5939x 1SM5940x 1SM5941x 1SM5942x 1SM5943x 1SM5944x 1SM5945x 1SM5946x 1SM5947x 1SM5948x 1SM5949x 1SM5950x 1SM5951x 1SM5952x 1SM5953x 1SM5954x 1SM5955x 1SM5956x SMx E03: Tape and reel for 3k pc 10/4/2014 2/12
SM 1SM5927 PACKAGE OUTLINE DIMENSIONS Dim Min(mm) Max(mm) A 3,30 3,94 4,06 4,7 C 1,91 2,11 D 0,15 0,31 E 5,08 5,59 G 0,05 0,2 H 0,76 1,52 J 2,13 2,44 10/4/2014 3/12
SM Limiting Values (Absolute Maximum Rating) Parameter Symbols Value Unit Power Dissipation @ TL =75 C Type Thermal Resistance (Note 1) IF=200mA Forward Voltage Operating Junction and Storage Temperature Range PD 3000 mw RθJA 226 C /W VFM 1,5 V TJ,TSTG -55 --- +150 C Electrical Characteristics (Ta=25 C Unless otherwise specified) Part No. 1SM5913 1SM5914 1SM5915 1SM5916 1SM5917 1SM5918 1SM5919 1SM5920 1SM5921 1SM5922 1SM5923 1SM5924 1SM5925 1SM5926 1SM5927 1SM5928 1SM5929 Nominal Zener Voltage Nom.(V ) Maximum Zener Impedance Maximum Reverse Leakage Current Maximum DC Zener Current VZ @ IZT ZZT@ IZT ZZK IR(uA) IZM Max. @IZK(mA IZT(mA) Max.(Ω) Max.(uA) @VR(V) ma (Ω) ) 3,3 113,6 10 500 1 100 1 454 3,6 104,2 9 500 1 75 1 416 3,9 96,1 7,5 500 1 25 1 384 4,3 87,2 6 500 1 5 1 348 4,7 79,8 5 500 1 5 1,5 319 5,1 73,5 4 500 1 5 2 294 5,6 66,9 2 250 1 5 3 267 6,2 60,5 2 200 1 5 4 241 6,8 55,1 2,5 200 1 50 5,2 220 7,5 50 3 400 0,5 50 6 200 8,2 45,7 3,5 400 0,5 50 6,5 182 9,1 41,2 4 500 0,5 50 7 164 10 37,5 4,5 500 0,25 50 8 150 11 34,1 5,5 550 0,25 50 8,4 136 12 31,2 6,5 550 0,25 1 9,1 125 13 28,8 7 550 0,25 1 9,9 115 15 25 9 600 0,25 1 11,4 100 10/4/2014 4/12
SM 1SM5930 1SM5931 1SM5932 1SM5933 1SM5934 1SM5935 1SM5936 1SM5937 1SM5938 1SM5939 1SM5940 1SM5941 1SM5942 1SM5943 1SM5944 1SM5945 1SM5946 1SM5947 1SM5948 1SM5949 1SM5950 1SM5951 1SM5952 1SM5953 1SM5954 1SM5955 1SM5956 16 23,4 10 600 0,25 1 12,2 93 18 20,8 12 650 0,25 1 13,7 83 20 18,7 14 650 0,25 1 15,2 75 22 17 17,5 650 0,25 1 16,7 68 24 15,6 19 700 0,25 1 18,2 62 27 13,9 23 700 0,25 1 20,6 55 30 12,5 26 750 0,25 1 22,8 50 33 11,4 33 800 0,25 1 25,1 45 36 10,4 38 850 0,25 1 27,4 41 39 9,6 45 900 0,25 1 29,7 38 43 8,7 53 950 0,25 1 32,7 34 47 8 67 1000 0,25 1 35,8 31 51 7,3 70 1100 0,25 1 38,8 29 56 6,7 86 1300 0,25 1 42,6 26 62 6 100 1500 0,25 1 47,1 24 68 5,5 120 1700 0,25 1 51,7 22 75 5 140 2000 0,25 1 56 20 82 4,6 160 2500 0,25 1 62,2 18 91 4,1 200 3000 0,25 1 69,2 16 100 3,7 250 3100 0,25 1 76 15 110 3,4 300 4000 0,25 1 83,6 13 120 3,1 380 4500 0,25 1 91,2 12 130 2,9 450 5000 0,25 1 98,8 11 150 2,5 600 6000 0,25 1 114 10 160 2,3 700 6500 0,25 1 121,6 9 180 2,1 900 7000 0,25 1 136,8 8 200 1,9 1200 8000 0,25 1 152 7 10/4/2014 5/12
SM Characteristics(Typical) 10/4/2014 6/12
SM SPECIFICATION Tape And Reel Package P0 E P2 D W F D1 P1 A Type A W E F P 0 P 1 P 2 ΦD ΦD 1 T1 4,30 ±0,1 8,20 MAX 12,00±0,30 1,75±0,05 5,5 ±0,05 4,00±0,10 4,00±0,10 2,00±0,05 1,55±0,03 1,5 2,77 MAX 10/4/2014 7/12
SM Cover Tape Peel off Strength Specifications: peel force of top cover tape shall be between 8 to 40g The peel speed shall be about 300mm/min±5% Type Packaging M A C D W T Embossed 178,0±1,0 2±0,5 13,5±0,7 21±0,5 60,0+1,0 13,5±1,0 15,5±1,0 Stock period The performance of these products, including the solderability, is guaranteed for 12 month, provided that they remain packed as they were when delivered and stored at a temperature of 25 C ± 3 C and a relative humidity less than 80%RH 10/4/2014 8/12
Lead Free Reflow Soldering Profile Recommended Land Pattern Design : Dimensions Value (in mm) Z 6,8 G 1,8 X 2,3 Y 2,5 C 4,3 10/4/2014 9/12 GmbH www.freltec.com
SM Item Requirement Test Method Tol. 0,05% Tol. > 0,05% Temperature Coefficient of Resistance (T.C.R.) As Spec. MIL-STD-202F Method 304 +25/-55/+25/+125/+25 C Short Time Overload Insulation Resistance Endurance Damp Heat with Load ΔR±0,05% ΔR±0,2% JIS-C-5201-1 5.5 RCWV*2,5 or Max. overload voltage for 5 seconds ΔR±0,2% for high power rating >1000 MΩ ΔR±0,05% >7kΩ ΔR±0,5% ΔR±0,2% ΔR±0,5% for high power rating ending Strength ΔR±0,05% ΔR±0,2% Solderability MIL-STD-202F Method 302 Apply 100V DC for 1 minute MIL-STD-202F Method 108A 70 2 C, Max. working voltage for 1000 hrs with 1,5 hrs ON and 0,5 hrs OFF ΔR±0,05% ΔR±0,3% MIL-STD-202F Method 103 40 2 C, 90~95% R.H. Max. working voltage for 1000 ΔR±0.5% for high power rating hrs with 1,5 hrs ON and 0,5 hrs OFF 95% min. coverage Resistance to Soldering Heat ΔR±0,05% ΔR±0,2% Dielectric Withstand Voltage y Type Thermal Shock ΔR±0,05% ΔR±0,25% JIS-C-5201-1 6.1.4 ending amplitude 3 mm for 10 seconds MIL-STD-202F Method 208H 245 5 C for 3 seconds MIL-STD-202F Method 210E 260±5 C for 10 seconds MIL-STD-202F Method 301 Max. overload voltage for 1 minute MIL-STD-202F Method 107G -55 C ~150 C, 100 cycles Low Temperature Operation ΔR±0,05% ΔR±0,2% JIS-C-5201-1 7.1 1 hour, -65 C, followed by 45 minutes of RCWV ΔR±0,5% for high power rating 10/4/2014 10/12
SM For this part: It does not use the materials that include the substances specified in RoHS, the detail refer to the part of prohibition or exclusion items in RoHS (2011/65/EU), Cadmium and cadmium compounds (permissive content<100 ppm) Lead and lead compounds (permissive content<1000 ppm) Exceptions specified: Lead contained in the glass of cathode ray tubes, electronic components and fluorescent tubes, The glass material used in the electronic components, which includes resistor elements, conductive pastes (silver or copper ones), adhesives, glass frit and sealing materials, Mercury and its mercury compounds (permissive content<1000 ppm) Hexavalent chromium compounds (permissive content<1000 ppm) Polybrominated biphenyls (P) (permissive content<1000 ppm) Polybrominated diphenylethers (PDE) (permissive content<1000 ppm) 10/4/2014 11/12
SM Published by GmbH Mathildenstr. 10A; 82319 Starnberg; Germany 2014 GmbH. All Rights Reserved. The following applies to all products named in this publication: 1. The information describes the type of component and shall not be considered as assured characteristics. 2. Terms of delivery and rights to change design reserved. 3. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. Nevertheless, we explicitly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether a product with the properties described in the product specification is suitable for use in a particular customer application. 4. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 5. The warnings, cautions and product-specific notes must be observed. 6. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous ). Useful information on this will be found in our Material Data Sheets. Should you have any more detailed questions, please contact our sales offices. 7. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true for the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. 8. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the General conditions for the supply of products and services of the electrical and electronics industry published by the German Electrical and Electronics Industry Association (ZVEI), available at www.freltec.com. 9. As far as patents or other rights of third parties are concerned, liability is only assumed for components per se, not for applications, processes and circuits implemented within components or assemblies. 10. The trade name is a trademark registered or pending in Europe and in other countries. 10/4/2014 12/12