122 Drive Pins Standard Pins Drive pins with a.300 diameter head are designed for permanently fastening a fixture to concrete, some types of masonry and A36 structural steel. Drive pins are manufactured with a 0.143" diameter shank in various lengths. Knurled shank designs are available to increase performance in steel base materials. A plastic flute is mounted over the point to retain the drive pin in the fastener guide of the tool providing guidance during the driving operation. Drive Pin Sizes P50012 1/2" (knurled) 100 5000.300.143 P50016 5/8" (knurled) 100 5000.300.143 P50022 3/4" 100 5000.300.143 P50023 3/4" Black Pins 100 5000.300.143 P50026 1" 100 5000.300.143 P50030 1-1/8" 100 1000.300.143 P50032 1-1/4" 100 1000.300.143 P50034 1-1/2" 100 1000.300.143 P50036 1-3/4" 100 1000.300.143 P50038 2" 100 1000.300.143 P50040 2-1/4" 100 1000.300.143 P50042 2-3/8" 100 1000.300.143 P50044 2-1/2" 100 1000.300.143 P50046 2-3/4" 100 1000.300.143 P50048 3" 100 1000.300.143 With Top Hat The pins listed below are used primarily for applications fastening drywall track to concrete or steel. They are assembled with a metal top hat to provide extra bearing surface against the drywall track. P50136 1/2" knurled 100 5000.300.143 P50138 5/8" knurled 100 5000.300.143 P50140 3/4" 100 5000.300.143 P50144 1" 100 5000.300.143 - Master Pack P50980 1/2" knurled 1000 5000.300.143 P51041 3/4" Black Pins 1000 5000.300.143 P53300 5/8" knurled 1000 5000.300.143 P53400 5/8" knr. Top Hat 1000 5000.300.143 P51040 3/4" 1000 5000.300.143 P51100 1" 1000 5000.300.143 P51160 1-1/4" 1000 5000.300.143 P51340 1/2" knr. Top Hat 1000 5000.300.143 P51400 3/4" Top Hat 1000 5000.300.143 P51520 1" Top Hat 1000 5000.300.143 Washered Pins To provide resistance to pullover, these pins are available with preassembled 14 gage (0.075") metal washers in various diameters. The insulation washer has a thickness of 0.035". with 3/4" Washer P50070 3/4" 100 1000.300.143 P50080 2-1/2" 100 1000.300.143 P50082 3" 100 1000.300.143 with 7/8" Washer P50090 1" 100 1000.300.143 P50092 1-1/4" 100 1000.300.143 P50094 1-1/2" 100 1000.300.143 P50096 2" 100 1000.300.143 P50098 2-1/2" 100 1000.300.143 P50100 3" 100 1000.300.143 with 1" Washer P50108 1-1/4" 100 1000.300.143 P50110 1-1/2" 100 1000.300.143 P50112 2" 100 1000.300.143 P50114 2-1/2" 100 1000.300.143 P50116 3" 100 1000.300.143
123 Drive Pins (Cont.) 8mm Head Drive Pins (Cont.) P50184 22mm - 7/8" 100 5000 8mm.143 P50186 27mm - 1" 100 5000 8mm.143 P50188 32mm - 1-1/4" 100 1000 8mm.143 P50190 37mm - 1-1/2" 100 1000 8mm.143 P50192 42mm - 1-5/8" 100 1000 8mm.143 P50194 47mm - 1-7/8" 100 1000 8mm.143 P50196 52mm - 2" 100 1000 8mm.143 P50198 57mm - 2-1/4" 100 1000 8mm.143 P50200 62mm - 2-1/2" 100 1000 8mm.143 P50202 72mm - 2-7/8" 100 1000 8mm.143 Anchors with 1-7/16" Insulation Washer P50122 1-1/2" 100 1000.300.143 P50126 2-1/2" 50 500.300.143 P50132 3" 50 500.300.143.300 Head Step Shank Pins P51058 3/4" Step Shank 100 1000.300.143/.130 P51059 1" Step Shank 100 1000.300.143/.130 8mm Head Drive Pins X-DN Type Pins Drive pins with an 8mm diameter head are designed for permanently fastening a fixture to concrete, some types of masonry and A36 structural steel. Drive pins are manufactured with a 0.143" diameter shank in various lengths. Knurled shank designs are available to increase performance in steel base materials. An 8mm plastic washer is mounted over the point to retain the drive pin in the fastener guide of the tool providing guidance during the driving operation. 8mm Head Drive Pins P50180 16mm knrld - 5/8" 100 5000 8mm.143 P50182 19mm knrld - 3/4" 100 5000 8mm.143 8mm Diameter Head Drive Pins With Top Hat The pins listed below are used primarily for applications fastening drywall track to concrete or steel. They are assembled with a metal top hat to provide extra bearing surface against the drywall track. P50210 16mm knrld - 5/8" 100 5000 8mm.143 P50214 22mm - 7/8" 100 5000 8mm.143 P50216 27mm - 1" 100 5000 8mm.143 8mm Head Drive Pins - Master Pack P51700 16mm knr. T Hat 1000 5000 8mm.143 P51750 22mm Top Hat 1000 5000 8mm.143 Washered Pins To provide resistance to pullover, these pins are available with preassembled 14 gage (0.075") metal washers in various diameters. 8mm Head Diameter Drive Pins With 1" Washer P50220 27mm - 1" 100 1000 8mm.143 P50222 32mm - 1-1/4" 100 1000 8mm.143 P50224 37mm - 1-1/2" 100 1000 8mm.143 P50226 52mm - 2" 100 1000 8mm.143 P50228 62mm - 2-1/2" 100 1000 8mm.143 P50230 72mm - 2-7/8" 100 1000 8mm.143 Drilling, Tapping Strut Firestop Contractor
124 Drive Pins And EIFS Pins 6mm Head Drive Pins Drive pins with a 6mm diameter head are designed for permanently fastening a fixture to concrete, some types of masonry, and A36 structural steel. The pins are manufactured with a 0.143" diameter shank in various lengths. Knurled shank designs are available to increase performance in steel base materials. A 12mm metal washer is mounted over the point to retain the drive pin in the fastener guide of the tool providing guidance during the driving operation. 6mm Head Drive Pins P50750 16mm knrld. - 5/8" 100 5000 6mm.143 P50752 19mm knrld. - 3/4" 100 5000 6mm.143 P50754 22mm - 7/8" 100 5000 6mm.143 P50756 27mm - 1" 100 5000 6mm.143 P50758 32mm - 1-1/4" 100 5000 6mm.143 P50760 37mm - 1-1/2" 100 5000 6mm.143 P50762 42mm - 1-5/8" 100 1000 6mm.143 P50764 47mm - 1-7/8" 100 1000 6mm.143 P50766 52mm - 2" 100 1000 6mm.143 P50768 57mm - 2-1/4" 100 1000 6mm.143 P50770 62mm - 2-1/2" 100 1000 6mm.143 P50772 72mm - 2-7/8" 100 1000 6mm.143 3/8" Head Drive Pins Drive pins with a 3/8" diameter head are designed for permanently fastening a fixture to concrete, some types of masonry and A36 structural steel. The pins are manufactured with a 0.171" diameter shank in various lengths. A plastic flute is mounted over the point to retain the drive pin in the fastener guide of the tool providing guidance during the driving operation. P50162 1" 100 1000 3/8".171 P50164 1-1/4" 100 1000 3/8".171 P50166 1-1/2" 100 1000 3/8".171 P50170 2" 100 1000 3/8".171 P50172 2-1/2" 100 1000 3/8".171 P50174 3" 100 1000 3/8".171 P50176 3-1/8" 100 1000 3/8".216 (with step shank).188 Ballistic Point Drive Pins Power Point-Type Fasteners Premium drive pins with a.300 diameter head have a specially designed point to allow more consistent penetration into harder base materials. Will reduce failures in dense concrete and steel. Drive Pins are manufactured with a 0.150" diameter shank in various lengths. A plastic flute is mounted over the point to retain the drive pin in the fastener guide of the tool providing guidance during the driving operation. Ballistic Point Drive Pins (Black) P50052 1/2" Ballistic Pt Pin 100 1000.300.150 P50053 5/8" Ballistic Pt Pin 100 1000.300.150 P50054 3/4" Ballistic Pt Pin 100 1000.300.150 P50055 7/8" Ballistic Pt Pin 100 1000.300.150 Ballistic Point Step Shank Pins P50056 1-1/4" Ballistic Pt Pin 100 1000.300.181/.150 P50057 1-7/8" Ballistic Pt Pin 100 1000.300.181/.150 EIFS Pins EIFS is an acronym for Exterior Insulation & Finish Systems EIFS Pins with a.300 diameter read 1-1/2" length are designed for permanently fastening to concrete or concrete block, installation systems such as, waterproofing membranes, plastic sheeting, metal lathe and wire mesh for plaster and stucco systems. To provide resistance to pullover, these pins are pre-assembled onto a soft plastic diaphragm. Resistance to pullover is increased by the additional bearing surfaces that are provided by the diaphragm. No. Description Box Ctn. P50282 EIFS Fastener 1-1/2" pin & plastic washer 1000 1000
125 Threaded Studs, Assemblies And Assemblies & Assemblies are combinations of drive pins and stamped steel clips designed for special applications. The pins are held within the clip using either a dome mechanism or a metal top hat. Ceiling Clip Assemblies For applications suspending acoustical ceiling systems or light fixtures, several styles of angled clips are pre-mounted onto pins. Anchors Threaded Studs Threaded studs are available in 1/4"-20 and 3/8"-16 thread diameters with a variety of thread and shank lengths for use in concrete, some types of masonry, and A36 structural steel. They are used for applications where it may be desirable to remove the fixture, where shimming may be required. The shank diameter for the threaded studs is 0.143" for the 1/4"-20 diameter and 0.205" for the 3/8"-16 diameter. Knurled shank designs are available to increase performance in steel base materials. A plastic flute is mounted over the point to retain the drive pin in the fastener guide of the tool providing guidance during the driving operation. On the 1/4"-20 threaded studs, a plastic cap is also provided to protect the threads of the fastener during the driving process. 1/4"-20 Threaded Studs Thread Shank Thread Shank No. Length Length Box Ctn. Dia. Dia. P50320 1/2" 1/2" K 100 5000 1/4".143 P50322 3/4" 1/2" K 100 1000 1/4".143 P50326 3/4" 3/4" 100 1000 1/4".143 P50328 1/2" 1" 100 1000 1/4".143 P50330 3/4" 1" 100 1000 1/4".143 P50334 1/2" 1-1/4" 100 1000 1/4".143 P50336 3/4" 1-1/4" 100 1000 1/4".143 P50338 1-1/4" 1-1/4" 100 1000 1/4".143 K=Knurled.300 Head Pins With Ceiling Clips Wire No. Description Box Ctn. Dia. Dia. Hole P50363 1" 100 1000.300.143.278" P50364 1" 100 1000.300.143.278" P50368 1" 100 1000.300.143.278" P50370 1-1/4" 100 1000.300.143.278" P50374 1-1/4" 100 1000.300.143.278" Economy Clip Ceiling clip without dome 8mm Drive Head Pins With Ceiling Clips Wire No. Description Box Ctn. Dia. Dia. Hole P50272 27mm w/cc 100 1000 8mm.143.278" P50274 32mm w/cc 100 1000 8mm.143.278" Ballistic Point Drive Pin With Ceiling Clip P50058 1-1/4" with 100 1000.300.181/.150 ceiling clip Drilling, Tapping Strut 3/8"-16 Threaded Studs Thread Shank Thread Shank No. Length Length Box Ctn. Dia. Dia. P50340 1-1/4" 3/4" K 100 1000 3/8".205 P50342 1-1/4" 1" 100 1000 3/8".205 P50344 1-1/4" 1-1/4" 100 1000 3/8".205 K=Knurled Factory Mutual Research Corp. approved Pipe Hanger Components Pre-Assembled Pin and Clip For Ladd Tool (L1600) Wire No. Description Box Ctn. Dia. Dia. Hole P50438 Pre-assembled 100 1000.310.155.278" Pin Clip P50440 Ladd Pin & 100 1000.310.155.278" Washer Assembly Firestop Contractor
126 Assemblies & (Cont.) BX And EMT Conduit Clip Assemblies With BX Cable Clips For the electrical trade, BX and EMT conduit clips are provided in various sizes for attaching conduit to base materials. No. Description Box Ctn. Dia. Dia. P50150 1" (BX) 100 1000.300.143 P50152 1-1/4" (BX) 100 1000.300.143 With EMT Conduit Clips No. Description Box Ctn. Dia. Dia. P50380 1/2" EMT 1-1/4" 100 1000.300.143 P50381 1/2" EMT 1" pin TH 100 1000.300.143 P50382 1/2" EMT 1" pin 100 1000.300.143 P50384 3/4" EMT 1-1/4" 100 1000.300.143 P50385 3/4" EMT 1" pin TH 100 1000.300.143 P50386 3/4" EMT 1" pin 100 1000.300.143 P50388 1" EMT 1" pin TH 25 250.300.143 8mm Diameter Head Drive Pins With EMT Conduit Clips No. Description Box Ctn. Dia. Dia. P50276 27mm TH w/ 1/2" EMT 100 1000 8mm.143 P50278 27mm TH w/ 3/4" EMT 100 500 8mm.143 P50280 27 mm TH w/ 1" EMT 25 250 8mm.143 Rebar Basket Assemblies Rebar basket clips are typically used in highway construction and paving applications to hold the support baskets for the reinforcing bars in place while the concrete is being poured. 8mm Head Drive Pins With Rebar Basket Clip No. Description Box Ctn. Dia. Dia. P50702 32mm w/basket clip 100 500 8mm.143 P50704 37mm w/basket clip 100 500 8mm.143 P50710 47mm w/basket clip 100 500 8mm.143 P50712 52mm w/basket clip 100 500 8mm.143 P50716 62mm w/basket clip 100 500 8mm.143 P50718 72mm w/basket clip 100 500 8mm.143 Forming Pin For concrete forming applications, the 1-3/4" (44mm) pin is designed for fastening wood members up to 3/4" in thickness while the 2-1/2" (62mm) pin is designed for wood members up to 1-1/2" in thickness. The pin has a break off groove 1" from the point to allow the wood forming members to be easily removed. P50789 44mm - 1-3/4" 100 1000.181.143 P50790 62mm - 2-1/2" 100 1000.181.143 Fastener In addition to the assemblies, the following accessories are available for use with drive pins or threaded studs as indicated below. No. Description Box Ctn. P50400 Ceiling Clip (no pin) 9/32" & 5/16" holes 100 1000 P50404 1/4" - 20 thrd. coupling 100 1000 P50408 3/8" - 16 thrd. coupling 100 1000 P50414 1/4" - 20 eye coupling (1/4" Wire Hole) 100 1000 P50416 3/4" metal washer - 14 gage 100 1000 P50418 7/8" metal washer - 14 gage 100 1000 P50420 1" metal washer - 14 gage 100 1000 P50439 LADD Clip - No pin 100 1000 P50365 Domed Ceiling Clip - No pin 100 1000 P50375 Economy Ceiling Clip - No pin 100 1000
127 Powder Actuated Fastener Guns Drive Pins And Tools Hammer Drive Pins No Powder Loads Required Hammer Drive Pins are designed for permanently fastening a fixture to concrete and some types of masonry. This fastener is designed for use in a standard hand tool and should not be used in a powder actuated tool. The pins are formed with a 1/4" diameter head on one end and a 0.140" diameter shank in various lengths. A 3/8" diameter steel washer is mounted over the point to retain the drive pin in the fastener guide of the tool providing guidance during the driving operation. This fastener is recommended for light duty static load applications where holding power is not a critical factor. It should not be used overhead. 1/4" Head Hammer Drive Pins Shank Head Shank No. Length Box Ctn. Dia. Dia. P50294 3/4" 100 5000 1/4".140 P50296 1" 100 5000 1/4".140 P50298 1-1/4" 100 1000 1/4".140 P50300 1-1/2" 100 1000 1/4".140 P50302 2" 100 1000 1/4".140 Hammer Drive Setting Tool No. Description Box Ctn. P50310 Hammer Drive Tool - Standard 1 1 P7200 Size Range: 1/2" to 1-1/2" pin lengths,.22 caliber The P7200 is a low velocity, single shot.22 caliber tool which can be used to install.300" head drive pins, 8mm head drive pins and 1/4" - 20 threaded studs up to 1-1/2" in total length. The P7200 is commonly used in the drywall trade. P7200 Deluxe Kit Contents P7200 powder actuated tools are packaged in a deluxe kit box as listed below. P52004 P7200 Tool (Deluxe Kit) 1 P52020 1/8" Allen Wrench 1 P52024 5/32" Allen Wrench 1 P52028 3/4" Wire Brush 1 P52030 1/4" Wire Brush 1 P52336 Spall Guard 1 P52040 P7200 Tool Manual 1 For fastening ceiling clips overhead, 6' and 8' dielectric pole tools are available. Anchors Drilling, Tapping Strut Firestop P50060 6' Dielectric Pole Tool 1 P50063 8' Dielectric Pole Tool 1 Contractor
128 Powder Actuated Fastener Guns (Cont.) P2200 Size Range: 1/2" to 3" pin lengths,.22 caliber The P2200 is a low velocity, single shot,.22 caliber tool which can be used to install.300 head drive pins, 8mm head drive pins and 1/4" - 20 threaded studs, up to 3" in total length. The P2200 is designed for maintenance or residential contractors. P2200 Deluxe Kit Contents P52006 P2200 Tool (Deluxe Kit) 1 P52026 3/16" Allen Wrench 1 P52028 3/4" Wire Brush 1 P52030 1/4" Wire Brush 1 P52550 Spall Guard P2200 1 P52042 P2200 Tool Manual 1 P3500 Size Range: 1/2" to 3" pin lengths,.27 caliber The P3500 is a low velocity, semi-automatic,.27 caliber tool which can be used to install.300 head drive pins, 8mm head drive pins and 1/4" - 20 threaded studs, up to 3" in total length. The P3500 is designed for high speed and repetitive volume applications. P3500 Deluxe Kit Contents P52000 P3500 Tool (Deluxe Kit) 1 P52017 3mm Allen Wrench 1 P52018 5mm Allen Wrench 1 P52027 5/8" Wire Brush 1 P52029 1" Wire Brush 1 P52031 1-1/4" Wire Brush 1 P52166 Stabilizer P3500 1 P52120 Shear Clip (2) 1 P52122 Steel Annular Ball (2) 1 P52036 P3500 Tool Manual 1 For fastening ceiling clips overhead, 6' and 8' dielectric pole tools are available. P50065 6' Dielectric Pole Tool 1 P50066 8' Dielectric Pole Tool 1
129 Powder Actuated Fastener Guns (Cont.) For fastening ceiling clips overhead, 6' and 8' dielectric pole tools are available. P50065 6' Dielectric Pole Tool 1 P50066 8' Dielectric Pole Tool 1 Anchors P35s Size Range: 1/2" to 1-1/2" pin lengths,.25 caliber The P35s is specially designed for acoustical and drywall contractors. It is a low velocity, semi-automatic, tool which can be used to install.300 head drive pins, 8mm head drive pins and 1/4" - 20 threaded studs up to 1-1/2" in total length. The P35s is designed for high speed and repetitive volume applications. The standard version of the tool is supplied with a flat end piston and a full size baseplate/guide. A limited access baseplate/guide assembly is also available. P35s Deluxe Kit Contents FA35s Size Range: 1/2" to 1-1/2" pin lengths,.25 caliber The FA35s is a modified version of the P35s that allows the operator to install pins, 1/4-20 threaded studs and assemblies faster than ever before. The operator who uses the FA35s no longer needs to manually cycle the tool in order to advance the load strip. The spring-loaded baseplate and guide automatically advances the next live load when the tool is compressed against the work surface. All the operator needs to do is feed the next pin. FA35s Deluxe Kit Contents P52015 FA35s Tool (Deluxe Kit) 1 Drilling, Tapping P52002 P35s Standard Tool (Deluxe Kit) 1 P52003 P35s Ltd. Access (Deluxe Kit) 1 P52017 3mm Allen Wrench 1 P52018 5mm Allen Wrench 1 P52027 5/8" Wire Brush 1 P52029 1" Wire Brush 1 P52031 1-1/4" Wire Brush 1 P52222 Stabilizer P35s 1 P52120 Shear Clip (2) 1 P52122 Steel Annular Ball (2) 1 P52038 P35s Tool Manual 1 P52017 3mm Allen Wrench 1 P52018 5mm Allen Wrench 1 P52027 5/8" Wire Brush 1 P52029 1" Wire Brush 1 P52031 1-1/4" Wire Brush 1 P52222 Stabilizer P35s 1 P52120 Shear Clip (2) 1 P52122 Steel Annular Ball (2) 1 P52038 P35s Tool Manual 1 For fastening ceiling clips overhead, 6' and 8' dielectric pole tools are available. P50065 6' Dielectric Pole Tool 1 P50066 8' Dielectric Pole Tool 1 Strut Firestop Contractor
130 Powder Actuated Fastener Guns (Cont.) PA3500 Size Range: 1/2" to 3" pin lengths,.27 caliber The PA3500 is a modified version of the P3500 that includes a power adjuster, allowing the operator to effectively decrease the power level of the load being used. A red load can be toned down to the level of a green. PA3500 Deluxe Kit Contents P52019 PA3500 Tool (Deluxe Kit) 1 P52017 3mm Allen Wrench 1 P52018 5mm Allen Wrench 1 P52027 5/8" Wire Brush 1 P52029 1" Wire Brush 1 P52031 1-1/4" Wire Brush 1 P52166 Stabilizer P3500 1 P52120 Shear Clip (2) 1 P52122 Steel Annular Ball (2) 1 P52036 P3500 Tool Manual 1 For fastening ceiling clips overhead, 6' and 8' dielectric pole tools are available. P50065 6' Dielectric Pole Tool 1 P50066 8' Dielectric Pole Tool 1 Powder Loads Powers offers high quality powder loads, produced by the largest manufacturer in the United States, with unsurpassed quality and reliability. Specific load types are designed for each unique powder actuated tool. They are offered as single units for single shot tools and collated in groups of 10 into plastic strips or metal discs for semi-automatic tools..22 Caliber A Low Velocity Loads For Powers P7200, P2200, Ramset 721 and M70, Hilti DXE37 and DXE72 Master No. Description Box Ctn. Ctn. P50500 Gray,.22A 100 5000 20000 P50502 Brown,.22A 100 5000 20000 P50504 Green,.22A 100 5000 20000 P50506 Yellow,.22A 100 5000 20000.22 Caliber Loads For Ladd Ceiling Master Tool (L1600) Master No. Description Box Ctn. Ctn. P50514 Green - Ladd 100 5000 20000 P50516 Yellow - Ladd 100 5000 20000 P50518 Red - Ladd 100 5000 20000.25 Caliber Disk Loads For Ramset D45, D60, D60L Master No. Description Box Ctn. Ctn. P50530 Gray,.25 disk 100 1000 10000 P50532 Brown,.25 disk 100 1000 10000 P50534 Green,.25 disk 100 1000 10000 P50536 Yellow,.25 disk 100 1000 10000.25 Caliber Red Disk Loads For Ramset Model D45 Master No. Description Box Ctn. Ctn. P50538 Red,.25 disk 100 1000 10000 Ramset is a registered trademark of Illinois Tool Works, Inc. Hilti is a registered trademark of Hilti, Inc.
31 BRIGHTON-BEST FLAT HEAD SOCKET CAP SCREWS - COARSE THREAD 1/8 100 1,000 FSC25618 2-56 1/4 100 1,000 FSC25614 3/8 100 1,000 FSC25638 1/2 100 1,000 FSC25612 1/4 100 1,000 FSC34014 3-40 3/8 100 1,000 FSC34038 1/2 100 1,000 FSC34012 3/4 100 1,000 FSC34034 3/16 100 5,000 FSC440316 1/4 100 5,000 FSC44014 3/8 100 5,000 FSC44038 4-40 1/2 100 5,000 FSC44012 5/8 100 5,000 FSC44058 1/16 Hex 3/4 100 5,000 FSC44034 T10 TORX 1 100 5,000 FSC4401 1 1/4 100 5,000 FSC440114 1 1/2 100 5,000 FSC440112 1/4 100 5,000 FSC54014 5-40 3/8 100 5,000 FSC54038 1/2 100 5,000 FSC54012 5/64 Hex 5/8 100 5,000 FSC54058 T10 TORX 3/4 100 5,000 FSC54034 1/4 100 5,000 FSC63214 5/16 100 5,000 FSC632516 6-32 3/8 100 5,000 FSC63238 1/2 100 5,000 FSC63212 5/64 Hex 5/8 100 5,000 FSC63258 T15 TORX 3/4 100 5,000 FSC63234 1 100 5,000 FSC6321 1 1/2 100 5,000 FSC632112 2 100 5,000 FSC6322 1/4 100 5,000 FSC83214 3/8 100 5,000 FSC83238 1/2 100 5,000 FSC83212 8-32 5/8 100 5,000 FSC83258 3/4 100 5,000 FSC83234 3/32 Hex 7/8 100 5,000 FSC83278 T20 TORX 1 100 5,000 FSC8321 1 1/4 100 5,000 FSC832114 1 1/2 100 5,000 FSC832112 2 100 5,000 FSC8322 3/8 100 5,000 FSC102438 1/2 100 5,000 FSC102412 10-24 5/8 100 5,000 FSC102458 3/4 100 5,000 FSC102434 1/8 Hex 7/8 100 5,000 FSC102478 T25 TORX 1 100 5,000 FSC10241 1 1/4 100 5,000 FSC1024114 1 1/2 100 5,000 FSC1024112 1 3/4 100 5,000 FSC1024134 3/8 100 5,000 FSC142038 1/2 100 5,000 FSC142012 5/8 100 5,000 FSC142058 3/4 100 5,000 FSC142034 1/4-20 7/8 100 5,000 FSC142078 1 100 4,000 FSC14201 5/32 Hex 1 1/4 100 3,000 FSC1420114 T30 TORX 1 1/2 100 2,000 FSC1420112 1 3/4 100 2,000 FSC1420134 2 100 2,000 FSC14202 2 1/2 100 2,000 FSC1420212 3 100 2,000 FSC14203 3 1/2 100 2,000 FSC1420312 4 100 2,000 FSC14204 3/8 100 3,000 FSC5161838 1/2 100 3,000 FSC5161812 5/8 100 3,000 FSC5161858 3/4 100 3,000 FSC5161834 5/16-18 7/8 100 3,000 FSC5161878 1 100 2,000 FSC516181 3/16 Hex 1 1/4 100 2,000 FSC51618114 T40 TORX 1 1/2 100 1,500 FSC51618112 1 3/4 100 1,000 FSC51618134 2 100 1,000 FSC516182 2 1/4 100 1,000 FSC51618214 2 1/2 100 1,000 FSC51618212 3 100 1,000 FSC516183 1/2 100 2,000 FSC381612 5/8 100 2,000 FSC381658 3/4 100 1,500 FSC381634 3/8-16 7/8 100 1,500 FSC381678 1 100 1,500 FSC38161 7/32 Hex 1 1/4 100 1,000 FSC3816114 T45 TORX 1 1/2 100 1,000 FSC3816112 1 3/4 100 700 FSC3816134 2 100 700 FSC38162 2 1/4 100 700 FSC3816214 2 1/2 50 500 FSC3816212 3 50 500 FSC38163 3 1/2 50 500 FSC3816312 3/4 100 1,500 FSC7161434 7/16-14 1 100 1,000 FSC716141 1 1/4 100 1,000 FSC71614114 1/4 Hex 1 1/2 100 600 FSC71614112 T50 TORX 1 3/4 100 600 FSC71614134 2 50 600 FSC716142 2 1/2 50 600 FSC71614212 1/2 100 1,500 FSC121312 3/4 100 1,000 FSC121334 1 100 700 FSC12131 1 1/4 100 700 FSC1213114 1 1/2 100 500 FSC1213112 1/2-13 1 3/4 50 500 FSC1213134 2 50 500 FSC12132 5/16 Hex 2 1/4 50 350 FSC1213214 T50 TORX 2 1/2 50 350 FSC1213212 3 50 300 FSC12133 3 1/2 25 300 FSC1213312 4 25 300 FSC12134 4 1/2 25 300 FSC1213412 5 25 300 FSC12135 6 25 300 FSC12136 Anchors Drilling, Tapping Strut Firestop Contractor
132 Powder Load Strips (Cont.), Trak-It Fuel Cells.27 Caliber Safety Strip Loads - Master Pack No. Description Box Ctn. P50624 Green,.27 Safety Strip 1000 10000 P50628 Yellow,.27 Safety Strip 1000 10000 P50632 Red,.27 Safety Strip 1000 10000 Trak-It Fasteners Use In: Concrete, Block and A36 Steel Size Range: 1/2" to 1-1/2" Pin Lengths Anchor Material: Carbon Steel Trak-It Fasteners and the Trak-It Fuel Cell are designed to be used with the Powers Trak-It Tool* and can also be installed with the ITW Ramset TrakFast tool. Then fasteners are collated on each patented, plastic top hat-style strip. Use for light duty static applications such as drywall track to concrete, block or steel, lath to concrete or block, furring strips to concrete or block, and plywood to concrete or block base materials. The fuel cell, with its unique right angle metering valve, contains enough gas to install up to 1200 fasteners. Each package contains 1000 fasteners and 1 fuel cell. Trak-It Fasteners / Trak-It Fuel Cell No. Shank Length Box Ctn. P55020 1/2" Trak-It Pin Zinc & Fuel Cell 1000 5000 P55022 3/4" Trak-It Pins & Fuel Cell 1000 5000 P55024 1" Trak-It Pins & Fuel Cell 1000 5000 P55026 1-1/4" Trak-It Pins & Fuel Cell 1000 5000 P55028 1-1/2" Trak-It Pins & Fuel Cell 1000 5000 P55012 Trak-It Lathing Washer 1000 5000 *Powers Trak-It Tool is currently in test market. Trak-It Fuel Cell No. Shank Length Box P55010 Trak-It Fuel Cell 10 * Powers Trak-It Tool is currently in test market. Multi Purpose Case No. P0278 Ramset is a registered trademark of Illinois Tool Works, Inc. TrakFast is a trademark of Illinois Tool Works, Inc. TIP For fastener technical specifications, please visit our web site at www.warwickfasteners.com and click on technical specifications.