PROUCT SUBMITTAL / SUBSTITUTION REQUEST TO: PROJECT: SPECIFIE ITEM: Section Page Paragraph escription PROUCT SUBMITTAL / SUBSTITUTION REQUESTE: The attached submittal package includes the product description, specifications, drawings, and performance data for use in the evaluation of the request. SUBMITTE BY: Name: Signature: Company: Address: ate: Telephone: Fax: FOR USE BY THE ARCHITECT AN/OR ENGINEER Approved Approved as Noted Not Approved (If not approved, please briefly explain why the product was not accepted.) By: ate: Remarks:
Selection Guides PROUCT INFORMATION Legend Suitable Maybe Suitable POWER ACTUATE FASTENING SELECTION GUIES Pin imensions Base Material Load Power Level Power Tools Other Tools Pin Category Product Page Shank Length Shank iameter Concrete Lightweight Concrete Grout-filled Concrete Masonry Steel Gray-Power Level Brown-Power Level 2 Green-Power Level 3 Yellow-Power Level 4 Red-Power Level 5 Purple/Black-Power Level 6 P3600 PA35 P380 P3500 / PA3500 P35s P720 P220 P7000 P60 Sniper Tool Hammer rive Tool 72 M70 LA(L600) 45 60 / 60L M380 SA270 Cobra Viper X E37 X E72 X400 X600N X35 X350 / X35 X36M X450 X45 XA40 XA4 X00 X200 X460 4 0.300 Head rive Pin /2 -/2-3 0.300 Head rive Pin 0.300 Head rive Pin with Top Hat 4 5 5 5 4 7 7 7 7 7 8 9 9 20 8 /2 -/2 0.300 Head rive Pin with Washers 2 3 0.300 Head Step Shank rive Pins 5/8 -/2 8mm Head rive Pin -5/8 2-7/8 8mm Head rive Pin 8mm Head rive Pin with Top Hat 5/8 0.45 / 0.45 0.45.30 8mm Head rive Pin with Washers -/2 2 2-7/8 8mm Head Spiral CSI rive Pin 5/8-5/8 Threaded Studs /4-20 Threaded Stud /2 -/4 3/8-6 Threaded Stud -/4 0.57 0.45 0.205 Heavy uty Pins 3/8 Head rive Pin 3-/8.72 /.26 /.88 0mm Head rive Pin 3-/4 0.77 www.powers.com Canada: (905) 673-7295 or (54) 63-426 Powers USA: (800) 524-3244 or (94) 235-6300
PROUCT INFORMATION Selection Guides Legend Suitable Maybe Suitable POWER ACTUATE FASTENING SELECTION GUIES (Continued) Pin imensions Base Material Load Power Level Power Tools Other Tools Pin Category Product Page Shank Length Shank iameter Concrete Lightweight Concrete Grout-filled Concrete Masonry Steel Gray-Power Level Brown-Power Level 2 Green-Power Level 3 Yellow-Power Level 4 Red-Power Level 5 Purple/Black-Power Level 6 P3600 PA35 P380 P3500 / PA3500 P35s P720 P220 P000 P60 Hammer rive Tool 72 M70 LA(L600) 45 60 / 60L M380 SA270 Cobra Viper X E37 X E72 X400 X600N X35 X350 / X35 X36M X450 X45 XA40 XA4 X00 X200 X460 Ballistic Point Pin Ballistic Point Pin 9 /2 7/8 Ballistic Point Step Shank Pin 9 9 22 20 2 2 2 22 34 34 34 34 34 34 35 35 35 35 -/4-7/8 0.50 0.8 /0.50 Specialty Fasteners Forming Pin - 2-/2 Hammer rive Pin -/4 0.45 / 0.30 0.45 Ceiling Clip Assemblies (.300 & 8mm) -/4 0.45 Clips and Accessories Ceiling Clip Assemblies CSI & Ballistic Point 7/8 -/4 0.57 & 0.50 0.45 0.45 Powers USA: (800) 524-3244 or (94) 235-6300 Canada: (905) 673-7295 or (54) 63-426 www.powers.com 2 BX-EMT Conduit Clip Assemblies (.300 &8mm) -/4 Rebar Basket Clip Assemblies (8mm) -5/8 2-7/8 22 Caliber A Single Load 22 Caliber A Single Loads Load Tool (L600) 25 Caliber isk Load Powder Actuated Loads 25 Caliber isk Loads (Red) 25 Caliber Single Load 27 Caliber Single Loads 27 Caliber Single Long Loads 25 Caliber 0 Load Strip 27 Caliber 0 Load Strip (Purple/Black) 27 Caliber Safety Strip
Powder Actuated PROUCT INFORMATION Powder Actuated Fastening INTROUCTION Powder actuated fastening systems provide a cost effective method of attaching fixtures for light duty, static load conditions. Powers' systems consist of specially designed fasteners, installation ols, and powder loads which are designed function in combination provide optimum performance. These systems provide the contracr with the ability fasten directly in concrete, masonry, and structural steel without pre-drilling holes. GENERAL APPLICATIONS AN USES Attaching Steel Concrete, Block or Steel Attaching Wood members Concrete, Block or Steel Attaching accessories Concrete, Block or Steel Attaching ceiling clips and threaded rod Concrete or Steel APPROVALS AN LISTINGS Tested in accordance ASTM E 488 and E 90 International Code Council, Evaluation Service (ICC-ES), ESR-2024 (Formerly ER-5330) International Code Council, Evaluation Service (ICC-ES), ESR-995 City of Los Angeles (COLA) Research Report LARR-25304 FM Global (Facry Mutual) - File No. J.I. 3002070 (Threaded Studs) SECTION CONTENTS Page No. Functioning Principles... 3 Powder Loads... 4 Fastener Types... 4 Functioning in Concrete... 5 Functioning in Steel... 5 Fastener Behavior... 6 Base Material Suitability... 7 Applied Loads... 7 esign Reference Guide for Concrete... 7 esign Reference Guide for Steel... 9 Performance ata... 0 FUNCTIONING PRINCIPLES Operating Principle Powder actuated systems, often described as forced entry systems, require special installation ols which are critical components of a successful fastening. Two types of ols have been used in the market which operate on different driving principles, direct acting and indirect acting. The basic design of the ols are similar in that each has a breech which holds the powder load and a barrel or guide mechanism hold the fastener. However, the installation and safety characteristics of the ols are very different. irect Acting Principle As the powder load is ignited in a direct acting ol, the expanding gases of the load act directly on the fastener drive it down the barrel of the ol and in the base material. In a ol of this type, 00% of the energy developed by the powder load is transferred the fastener. Penetration of the fastener in the base material is controlled primarily by the density of the base material and the load level selected. While the direct acting principle may allow fastenings be made in very dense concrete and thick steel base materials, safety concerns have made the indirect principle the technology of choice. Powder actuated ols using this principle are no longer commercially available. Indirect Acting Principle In a ol which operates using the indirect acting principle, the expanding gases of the ignited powder load act directly on a captive pisn which is housed within the barrel of the ol. The pisn drives the fastener in the base material providing better control over the penetration of the fastener. In a ol of this type, most of the energy developed by the powder load is retained by the pisn. Penetration of the fastener in the base material is controlled by the design of the pisn, the load level selected, and the density of the base material. All Powers' powder actuated ols operate using the indirect acting principle and are classified as low velocity ols. Tool Classification Powder actuated ols can be classified as low, medium, or high velocity. This classification system can apply either direct or indirect acting ols and is based on a ballistic test. Using the strongest powder load and the lightest fastener commercially available from the manufacturer for a specific ol, the velocity of the ol is determined by measuring the average velocity of the fastener for ten individual tests. The velocity classifications based on ANSI A0.3 are as follows:. Low Velocity Tool A ol in which the average test velocity does not exceed 328 feet per second (00 meters per second). 2. Medium Velocity Tool A ol in which the average test velocity exceeds 328 feet per second (00 meters per second) but is less than 492 feet per second (50 meters per second). Medium velocity ols are no longer commercially available. 3. High Velocity Tool A ol in which the average test velocity exceeds 492 feet per second (50 meters per second). High velocity ols are no longer commercially available. Tool Safety Powder actuated fasteners must be installed by properly trained and licensed operars as described in ANSI Standard A 0.3. Authorized Powers distriburs offer complete training programs for end users. Contact your local Powers branch office or distribur for complete details. While the powder actuated ols are summarized in this section of the manual, only trained and licensed operars are allowed use the ols. These summaries are for general information only. 3 www.powers.com Canada: (905) 673-7295 or (54) 63-426 Powers USA: (800) 524-3244 or (94) 235-6300
PROUCT INFORMATION Powder Actuated POWER LOAS The energy source used drive a powder actuated fastener in the base material is a self contained unit called a powder load. Specific load types are designed for each unique powder actuated ol. Powers ols use cased powder loads in which the propellant is housed in a crimped metal case. Powder Load Identification In the commercial market, cased powder loads are available in sizes ranging from.22.27 calibers. The power level or strength of a cased powder load is identified using a 2 level system in which a combination of six color codes and two case types are used. Power level /gray is the lowest with power level 2/purple being the highest. Only six color codes are used because there are not twelve easily distinguished colors available. The following table shows this identification system. Power Level Color Identification Case Color Load Color Brass Gray 2 Brass Brown 3 Brass Green 4 Brass Yellow 4.5 Brass Blue 5 Brass Red 6 Brass Purple 7 Nickel Gray 8 Nickel Brown 9 Nickel Green 0 Nickel Yellow Nickel Red 2 Nickel Purple Powder loads are available as single units for single shot ols and collated in groups of 0 in plastic strips or metal discs for semi-aumatic ols. Powers ols use.22 caliber A,.25 caliber, and.27 caliber crimped, rim fire powder loads having power FASTENER TYPES Several fastener types are available including drive pins and threaded studs along with application-specific assemblies. According ANSI A 0.3, only those types of fasteners and powder loads as recommended by the ol manufacturer for a particular ol, or those providing the same level of safety and performance, shall be used. Typical rive Pins.300" Head Ballistic Point.300" Head 8mm Head 0mm Head 3/8" Head rive pins are one of the most commonly specified type of powder actuated fastener. They are used fasten a fixture levels ranging from - 6. Powder loads for other commercially available ols are also available such as.22 caliber Ladd and.27 caliber long. Consult the individual ol instructions for details on the caliber, range, and type of load. The crimped tip on the load retains the powder in the casing. Wadded loads which have a plug in the front of the casing should never be used in ols designed for use with crimped loads such as low velocity, pisn ols. The wadding material can cause the ol clog or jam. Rim fire refers the method of actuation. In a rim fire powder load, the primer is contained in the rim of the casing. When the ol is fired, the firing pin strikes the rim causing the primer ignite which in turn ignites the powder contained in the main portion of the load. The power level of Powers powder loads is marked on each box. As the number increases, the power level also increases. Power level is also indicated by the color of the box, label, and the color on each individual powder load. Powder Load Selection Use of the proper power level is critical the success of a powder actuated fastening. Prior selecting the proper power level, conduct a center punch test as described in the upcoming section on base material suitability. To select the proper power level be used with a specific fastener, always perform a test firing using the lowest power level recommended for the ol being used. On ols which have a variable power control, use the lowest possible setting. If the lowest power level does not fully drive the fastener, try a powder load having the next higher power level. Continue this procedure until the proper fastener penetration is obtained. directly the base material in one operation for permanent applications. Pins are available in several head configurations. Each of the head configurations has a corresponding shank diameter and a variety of lengths. Some drive pins designed for use in steel have a knurled shank provide increase load capacities. Other drive pins have a narrow shank diameter close its point and a wider shank diameter comprising the upper portion. This design is known as step shank and is used penetrate denser base materials more consistently. Threaded Studs /4"-20 3/8"-6 For applications where adjustment or removability may be required, threaded studs are available with both a /4" or 3/8" thread diameter. Each thread size has a corresponding shank diameter and is available in a variety of shank and thread lengths. Powers USA: (800) 524-3244 or (94) 235-6300 Canada: (905) 673-7295 or (54) 63-426 www.powers.com 4
Powder Actuated PROUCT INFORMATION FASTENER GUIANCE AN MATERIAL SPECIFICATIONS Fastener Guidance Both types of fastener have pre-mounted plastic fluting or washers which hold the fastener centered in the ol guide prior driving. uring the driving process, the fluting or washers provide point Head Guidance Point Guidance guidance for the fastener. Generally, head guidance is provided by the diameter of the fastener head or threads. /4"-20 threaded studs also have a plastic cap protect the threads of the fastener during the driving process providing head guidance. Fastener Material Specifications Mechanical Properties Powder actuated fasteners are subjected extremely high stresses as they are driven in the base material. A key aspect of their design is manufacture them from a material that is ugh enough prevent deformation of the fastener during the driving process with ductility prevent shattering. Powers fasteners are specially manufactured using a proprietary process meet these requirements. The fasteners are manufactured from ASTM A 50 SAE 060 steel and austempered a nominal core hardness of RC 5 55. Corrosion Resistance Powder actuated fasteners are designed be used in a noncorrosive atmosphere unless application specific corrosion testing has been performed. To reduce the possibility of the embrittlement of a heat treated part, the standard finish for all Powers fasteners is mechanically applied zinc meeting the requirements of ASTM B 695, Class 5, Type providing an average minimum thickness of 5 microns (0.0002") with no supplementary coating. FUNCTIONING OF POWER ACTUATE FASTENERS Functioning in Concrete The load capacity of a powder actuated fastener when installed in concrete or masonry base materials is based on the following facrs:. Strength of the base material 2. Hardness and concentration of the aggregate 3. Shank diameter of the fastener 4. epth of embedment in the base material 5. Fastener spacing and edge distance In addition these facrs, installation ol accessories such as a sp spall guard adapter which reduces the tendency of the concrete surface spall during the driving action can increase the performance of the fastener. When a powder actuated fastener is driven in concrete, it displaces the volume of concrete around the embedded area of the fastener shank. As this occurs, the concrete directly surrounding the fastener is compressed and in turn presses back against the shank of the fastener. Additionally, the driving action generates heat which causes particles within the concrete fuse the shank of the fastener. This combination of compression and fusion holds the fastener in the concrete base material. A similar action occurs when fastening in block masonry. Generally, the performance of the fastener in a given concrete strength will increase with greater embedment depths in a certain range. epending on the fastener style and base material strength, embedment depths range from 5/8" -/2". For depths greater than this range, there is the possibility of fastener bending or fishhooking which may decrease expected load capacities. For typical embedment depths achieved, refer the upcoming section on performance data andload capacities. Washer Sp Spall uring the driving action, some localized surface spalling of the concrete may occur. Normally, this is a surface effect which does not affect the performance of the fastener. However, it may pose an aesthetic problem for exposed applications where a fixture is not used. In cases such as this, two methods can be used improve the appearance of the fastening. A sp spall adapter mounted on the powder actuated ol can help reduce surface spalling. Another method used is drive the fastener through a steel washer improve the appearance of the application. Functioning in Steel The load capacity of a powder actuated fastener when installed in steel base materials is based on the following facrs:. Thickness of the steel 2. Tensile strength of the steel 3. Shank diameter of the fastener 4. epth of point penetration through the steel 5. Fastener spacing and edge distance. 5 www.powers.com Canada: (905) 673-7295 or (54) 63-426 Powers USA: (800) 524-3244 or (94) 235-6300
PROUCT INFORMATION Powder Actuated Functioning in Steel (Continued) When a powder actuated fastener is driven in steel, it displaces the steel laterally 360 degrees around the shank of the fastener. Since steel is an elastic material, it presses back against the shank of the fastener hold it in place. As the diameter of the fastener shank is increased, the load capacity obtained will generally increase provided the steel thickness is sufficient accept the fastener. To further increase fastener performance in steel, some fasteners have a knurled shank which allows the steel form a key lock in the grooves provide higher capacities than those obtained with a smooth shank. For typical performance, the fastener point should completely penetrate the steel. Normally, a minimum of /4" is allowed for the point length. An increase in performance can normally be expected until the fastener no longer completely penetrates through the steel. At this point, the elastic properties of the steel may cause a compression force be developed at an angle against the fastener point which can reduce load capacity. However, this can be subject the fastener type and in thicker steel base materials, adequate load capacities may be obtained for applications in which the point of the fastener does not fully penetrate the steel. Job site performance tests are recommended. Fasteners should not be used in areas that have been welded or cut with a rch as these procedures may have caused local hardening of the steel. Over driving of the fastener should be avoided as the rebound created may reduce the load capacity or cause damage both the fastener and the ol. When fastening in unsupported long steel members, it may be necessary provide support in the area of the fastening prevent spring action which can cause inconsistent penetration and a reduction in load capacity. FASTENER BEHAVIOR An understanding of the performance characteristics of a powder actuated fastener is an important aspect of the selection process. At ultimate failure, the following modes of failure can be expected. Bearing Failure The fixture or material fastened tears as a lateral load is applied and is pulled over the head of the fastener. Base Material Failure Fastener Pullout The fastener pulls out of the base material when subjected a tension load. In concrete, a typical cone type failure can be expected while in steel the fastener pulls out cleanly. Pullover Failure The fixture or material fastened pulls over the head of the fastener. This is a common occurrence when fastening lumber or thin metal materials. To help improve pullover resistance for applications such as this, Powers powder actuated fasteners are available with pre-mounted steel washers. Tightening Failure On threaded studs, the tightening rque applied must be limited prevent over tightening of the connection. This will prevent the development of a clamping force greater than the tension or pullout load resistance of the fastener. Shank Failure The shank of the fastener is broken due an applied lateral load such as shear. This can also happen when a bending load is created. Powers USA: (800) 524-3244 or (94) 235-6300 Canada: (905) 673-7295 or (54) 63-426 www.powers.com 6
Powder Actuated PROUCT INFORMATION BASE MATERIAL SUITABILITY While powder actuated fasteners can be used successfully in concrete, certain masonry materials, A36 and A572 steel, some materials are completely unsuitable. Fasteners should never be fired in hard or brittle materials such as cast iron, tile, glass, or rock. These materials can shatter easily resulting in a potential safety hazard. In addition, soft base materials such as wallboard, plaster, or wood are not appropriate as the fastener could pass completely through these materials. The user should never guess when fastening in any base material. A Center Punch Test should always be performed help determine the suitability of the base material for a powder actuated fastening. This test is relatively simple and can help ensure a safe, successful fastening. Be sure wear the appropriate eye protection when performing this test. To begin, select the fastener be used for the job. Then place the point of the fastener against the proposed base material. Strike the fastener with a single hammer blow and then examine the point. If the point of the fastener is not blunted and the base material has a clear point indentation, it is acceptable proceed with the first test installation. Use of a powder actuated system is not recommended if the following occurs during the Center Punch Test: Point Flattens No Indent. The fastener point has been blunted. This indicates that the base material is o hard. Surface Shatters Material Cracks 2. The base material cracks or shatters. This indicates that the base material is o brittle. Fastener Sinks in with Average Hammer Blow 3. When using an average hammer blow, the fastener penetrates the base material easily. This indicates that the base material is o soft. APPLIE LOAS The type of load and the manner in which it is applied by the fixture or other attachment is a primary consideration in the selection of a powder actuated fastener. Powder actuated fastening systems provide a cost effective method of attaching fixtures for light duty, static load conditions. The load capacities for powder actuated fasteners published in this manual represent the results of laborary testing conducted according ASTM Standards E 488 and E 90. As always, the suitability of a fastener for a specific application should be determined by a qualified design professional responsible for the product installation. Load A tension load is applied directly in line with the axis of the fastener. Load A shear load is applied perpendicular the fastener directly along the surface of the base material. Bending Loads The effect of bending resulting from the application of static shear load should be considered. This can occur in softer material such as lumber used for sill plates or when shims or spacers are placed between the fixture and the base material. In situations such as this, the load is applied at a distance from the surface of the base material creating a lever type action on the fastener. When a bending load is applied a fastener, it is often the physical strength of the fastener material, not the tension or shear load capacities, that limit the strength of the connection. For sill plate applications, Powers publishes test data based on the use of 2x lumber develop the capacities. The allowable bending load should be calculated by a design professional based on the material from which the fastener is manufactured. For threaded powder actuated fasteners and step shank pins, it is important remember that the point of maximum stress is at the interface of the shank and the base material. For example, when calculating the bending load for a fastener such as a /4"-20 threaded stud, it is important use the shank diameter of 0.45" in calculations, not the 0.2" root diameter of the threads. ESIGN REFERENCE GUIE FOR CONCRETE Allowable Load Capacities The allowable load capacity which may be applied a powder actuated fastener is based on applying a safety facr the average ultimate load capacity obtained from testing according ASTM Standards E 488 and E 90. One purpose of the safety facr is allow for field variations which may differ from the testing conditions in the laborary. An example is the type and strength of the base material. For proper performance, powder actuated fasteners must be installed by properly trained and licensed operars. In concrete and masonry materials, the values for allowable loads are based on applying a minimum safety facr of 5: or greater the ultimate loads. Loads are based on testing fasteners installed in base materials having the designated strength at the time of installation. Values are for the fastener only, connected parts must be investigated separately. ue the variability of powder actuated fasteners installed in concrete or masonry materials, use of multiple fasteners is recommended increase reliability. The design data listed in the tables are suggested allowable load capacities based on the noted safety facrs. These safety facrs are based on industry experience and may need be increased based on the application requirements or local codes as determined by the design professional responsible for the product installation. Proper spacing and edge distance guidelines must be followed. 7 www.powers.com Canada: (905) 673-7295 or (54) 63-426 Powers USA: (800) 524-3244 or (94) 235-6300
PROUCT INFORMATION Powder Actuated ESIGN REFERENCE GUIE FOR CONCRETE (Continued) Base Material Strength Spacing As discussed earlier in this manual, the strength of concrete and masonry base materials can vary widely. For installations in concrete, load capacities are published for powder actuated fasteners in normal-weight concrete in various compressive strength ranges. Linear interpolation of the data calculate load capacities for fasteners installed in intermediate concrete strengths is permitted. Normally, the load capacities can be expected increase as the compressive strength of the concrete base material increases. However, some types of high compressive strength concrete or concrete with a very hard aggregate may not be suitable for powder actuated fastenings. Job site installation tests are recommended determine fastener suitability. For structural lightweight concrete, values are published for minimum 3000 psi concrete with and without steel deck. For masonry base materials, the published load capacities are based on testing in a wall constructed from ASTM C 90, Grade N, lightweight block. Since the consistency of masonry block can vary widely, especially within the mortar used, these values should be used solely as a guide. Job site tests are recommended determine actual load capacities when used in masonry walls. Base Material Thickness Setting fasteners o close gether in concrete or masonry can cause cracking. The recommended minimum distance between fasteners is 3" center center. Unless specific fastener testing has been conducted qualify the condition and location. Length Selection For permanent applications using pins in concrete, first determine the thickness of the fixture be fastened. To this, add the required embedment or penetration in the base material. This will be the fastener shank length required. For applications in the face shell of masonry block, select a fastener length which will not exceed the thickness of the face shell. Fixture Embedment Threaded Length Embedment Concrete base material should be at least three (3) times as thick as the fastener embedment penetration Unless specific fastener testing has been conducted qualify the condition and location. If the concrete is o thin, the compressive forces forming at the fasteners point can cause the free face of the concrete break away. This can create a dangerous condition from flying concrete and/or the fastener and also results in a reduction of fastener holding power. For applications in the face shell of concrete masonry block, select a fastener length which will not exceed the thickness of the face shell. Edge istance Penetration 3x Penetration For removable applications with threaded studs, the shank length required is equal the embedment depth required. To determine the minimum threaded length, add the thickness of the fixture and the nut / washer thickness. The nut and washer thickness is equal the nominal thread diameter. For applications where 3/8" threaded studs are used at an embedment depth of -3/8", the fasteners were driven up the threaded portion of the part. o not over tighten threaded parts. Maximum tightening rque values are listed in the table below. Use of a nut setter is recommended reduce the possibility of over tightening the fasteners. For critical applications, perform a job site test. Maximum Torque Maximum Torque for /4" Stud (ft.-) for 3/8" Stud (ft.-) 2 4 o not fasten closer than 3" from the edge of concrete. If the concrete cracks, the fastener may not hold. Closer edge distances for applications such as sill plates may be permitted if specific fastener testing has been conducted qualify the location. Powers USA: (800) 524-3244 or (94) 235-6300 Canada: (905) 673-7295 or (54) 63-426 www.powers.com 8
Powder Actuated PROUCT INFORMATION ESIGN REFERENCE GUIE FOR STEEL Allowable Load Capacities The allowable load capacity which may be applied a powder actuated fastener is based on applying a safety facr the average ultimate load capacity obtained from testing according ASTM Standards E 488 and E 90. One purpose of the safety facr is allow for field variations which may differ from the testing conditions in the laborary. An example is the type and strength of the base material. For proper performance, powder actuated fasteners must be installed by properly trained and licensed operars. In steel materials, the values listed are based on a safety facr of 5: or greater the ultimate loads. Values are for the fastener only, connected parts must be investigated separately. Use of multiple fasteners is recommended increase reliability. The design data listed in the tables are suggested allowable load capacities based on the safety facrs noted below each table. This safety facr is based on industry experience and may need be increased based on the application or local code requirements as determined by the design professional responsible for the product installation. Proper spacing and edge distance guidelines must be followed. Base Material Strength The published allowable load capacities are based on testing conducted in ASTM A 36 structural steel with the fastener point fully penetrating the steel member. For use in higher strength steel, applications where the point of the fastener will not penetrate a thickness of steel greater than those listed in the tables, job site tests are recommended determine the suitability of the application and the actual load capacities. Base Material Thickness Steel base materials should be a minimum of /8 in thickness. Edge istance Length Selection For permanent applications when using pins in steel, first determine the thickness of the fixture be fastened. To this, add the thickness of the steel base material plus a minimum of /4" allow for point penetration. This will be the minimum fastener shank length required. o not select a fastener length longer than that required for the application. An excessively long shank can burnish or polish the hole created in the steel resulting in a reduction in load capacity. Fixture Steel Thickness /4" Threaded Length Steel Thickness For removable applications with threaded studs, the shank length required is equal the thickness of the steel base material plus a minimum of /4" allow for point penetration. This will be the minimum fastener shank length required. o not select a shank length longer than that required for the application. An excessively long shank can burnish or polish the hole created in the steel resulting in a reduction in load capacity. To determine the minimum threaded length, add the thickness of the fixture and the nut / washer thickness. The nut and washer thickness is equal the nominal thread diameter. o not over tighten threaded studs, the maximum tightening rque is listed in the table below. Use of a nut setter is recommended reduce the possibility of over tightening the fasteners. For critical applications, perform a job site test. Base Material Maximum Torque Maximum Torque Thickness (in.) for /4" Stud (ft.-) for 3/8" Stud (ft.-) /8" 2 4 3/6" 4 6 /4" 6 0 3/8" 8 2 Note: For steel base material thicknesses /2 and greater where point penetration is not possible, see the performance data for specific pins or perform a job site test determine the suitability of the application and actual load capacities. /4" For installations in steel, /2" is the recommended minimum edge distance. Spacing The recommended minimum distance between fastenings is -/2" center center for installations in steel. 9 www.powers.com Canada: (905) 673-7295 or (54) 63-426 Powers USA: (800) 524-3244 or (94) 235-6300
PROUCT INFORMATION Performance ata PERFORMANCE ATA Ultimate Load Capacities for Powder Actuated Fasteners in Normal-Weight Concrete,2,3,4,5 Pin escription Ballistic Point Pin (0.50" Shank) Ballistic Point Pin (0.8"/0.50" Shank) 0.300" Head rive Pin 8mm Head rive Pin /4"-20Threaded Stud (0.45" Shank) 8mm head Spiral CSI Pin (0.57" Shank) 0mm Head rive Pin (0.77" Shank) 3/8"-6 Threaded Stud (0.205" Shank) 3/8" Head rive Pin (0.72" Shank) Ceiling Clips - Spiral CSI Pin (0.57" Shank) Ceiling Clips w/ 0.300" Head Pin (0.45" Shank) Economy Ceiling Clips w/ 0.300" Head Pin (0.45" Shank) Ballistic Point Ceiling Clip (0.8"/0.50" Shank) Ceiling Clips - LA Pin (0.52" Shank) Rod Hanger Ceiling Clip (0.45" Shank) Minimum Embedment epth hv in. (mm) 5/8 (5.9) (9.) /4 (3.8) /2 (38.) 5/8 (5.9) (9.) /4 (3.8) /2 (38.) (9.) /4 (3.8) (9.) /4 (3.8) /4 (3.8) /2 (38.) /4 (3.8) /2 (38.) (9.) (9.) (9.) (9.) /8 (28.6) Minimum Concrete Compressive Strength (f'c) 2,000psi 2,500psi 3,000psi 4,000psi 4,500psi 5,000psi 370 (.6) 590 (2.6) 60 80 (3.6) 60 800 (3.6) 590 (2.6) 780 (3.5) 480 770 660 940 680 980 700,020 (2.) (3.4) (2.9) (4.2) (3) (4.4) (3.) (4.5) 690,30 770,200 820,350 870,500 (3.) (5) (3.4) (5.3) (3.6) (6) (3.9) (6.7) 80,460,30,490,380,680 7,620,890 (3.6) (6.5) (5) (6.6) (6.) (7.5) (33.9) (8.4) 920,780,490,780,930 2,020 2,370 2,250 (4.) (7.9) (6.6) (7.9) (8.6) (9) (0) 300 475 300 475 300 475 300 475 (.3) (2.) (.3) (2.) (.3) (2.) (.3) (2.) 300 475 475 625 475 625 500 625 (.3) (2.) (2.) (2.8) (2.) (2.8) (2.2) (2.8) 500 700 650 775 775 775 870,000 (2.2) (3.) (2.9) (3.4) (3.4) (3.4) (3.9) (4.4) 550 775 775 825 975 825,75,000 (2.4) (3.4) (3.4) (3.7) (4.3) (3.7) (5.2) (4.4) 575 875 900 875,75,75,450,000 (2.6) (3.9) (4) (3.9) (5.2) (5.2) (6.4) (4.4) 750 850 670 960 670 960 670 960 (3.3) (3.8) (3) (4.3) (3) (4.3) (3) (4.3),70 2,00,70 2,00,70 2,00 (7.6) (9.3) (7.6) (9.3) (7.6) (9.3),550,925 (6.9) (8.6) 350 475 525 725 540 740 350 500 550 750 (.6) (2.) (2.3) (3.2) (2.4) (3.3) (.6) (2.2) (2.4) (3.3) 875 925 890 940 900 950 (3.9) (4.) (4) (4.2) (4) (4.2),075,050,225,25,225,25 800 850,225,25 (4.8) (4.7) (5.4) (5) (5.4) (5) (3.6) (3.8) (5.4) (5) 475 675 475 675 800 675 800 675 (2.) (3) (2.) (3) (3.6) (3) (3.6) (3) 850,00 850,00,000,600,000,600 (3.8) (4.9) (3.8) (4.9) (4.4) (7.) (4.4) (7.),50,375,375,625,475,975,475,975 (5.) (6.) (6.) (7.2) (6.6) (8.8) (6.6) (8.8) 930,780,60 2,20,30 2,20,600 2,20 (4.) (7.9) (5.2) (9.4) (5.8) (9.4) (7.) (9.4),470 2,540 2,040 2,540 2,040 2,540 2,040 2,540 (6.5) (.3) (9.) (.3) (9.) (.3) (9.) (.3) 700,000 700,000 (3.) (4.4) (3.) (4.4) 300 475 325 525 350 725 350 725 (.3) (2.) (.4) (2.3) (.6) (3.2) (.6) (3.2) 300 550 475 600 500 800 500 800 (.3) (2.4) (2.) (2.2) (3.6) (2.2) (3.6) 250 475 300 525 350 725 350 725 (.) (2.) (.3) (2.3) (.6) (3.2) (.6) (3.2) 250 600 300 600 500 750 500 750 (.) (.3) (2.2) (3.3) (2.2) (3.3) 500,020 (2.2) (4.5) 250 250 250 650 675 800 675 800 (.) (.) (.) (2.9) (3) (3.6) (3) (3.6) 900-900 - (4) (4). Fasteners must not be driven until the concrete has reached the minimum designated compressive strength. 2. Concrete thickness must be a minimum of three times the embedment depth. 3. The ultimate tension and shear values are for fasteners only. Steel or wood members connected the substrate must be investigated for compliance with the applicable code. 4. The values listed above are ultimate load capacities which should be reduced by a facr of safety determine the allowable working load. For allowable load capacities, see the allowable load tables. 5. Multiple fasteners are recommended for any attachment for increased reliability. Powers USA: (800) 524-3244 or (94) 235-6300 Canada: (905) 673-7295 or (54) 63-426 www.powers.com 0
Performance ata PROUCT INFORMATION PERFORMANCE ATA Allowable Load Capacities for Powder Actuated Fasteners in Normal-Weight Concrete,2,3,4,5 Pin escription Ballistic Point Pin(0.50" Shank) Ballistic Point Pin (0.8"/0.50" Shank) 0.300" Head rive Pin 8mm Head rive Pin /4"-20Threaded Stud (0.45" Shank) 8mm head Spiral CSI Pin (0.57" Shank) 0mm Head rive Pin (0.77" Shank) 3/8"-6 Threaded Stud (0.205" Shank) 3/8" Head rive Pin (0.72" Shank) Ceiling Clips - Spiral CSI Pin (0.57" Shank) Ceiling Clips w/ 0.300" Head Pin (0.45" Shank) Economy Ceiling Clips w/ 0.300" Head Pin (0.45" Shank) Ballistic Point Ceiling Clip (0.8"/0.50" Shank) Ceiling Clips - LA Pin (0.52" Shank) Rod Hanger Ceiling Clip (0.45" Shank) Minimum Embedment epth hv in. (mm) 5/8 (5.9) (9.) /4 (3.8) /2 (38.) 5/8 (5.9) (9.) /4 (3.8) /2 (38.) (9.) /4 (3.8) (9.) /4 (3.8) /4 (3.8) /2 (38.) /4 (3.8) /2 (38.) (9.) (9.) (9.) (9.) /8 (28.6) 45 60 85 00 5 25 (0.) 60 00 0 5 Minimum Concrete Compressive Strength (f'c) 2,000psi 2,500psi 3,000psi 4,000psi 4,500psi 5,000psi 75 95 40 85 225 () 45 95 40 55 75 20 75 85 95 40 85 60 95 30 55 80 70 34 342 (.5) 30 (.4) 70 385 (.7) 95 00 20 50 85 225 () 95 25 55 65 75 92 420 (.9) 75 85 05 75 240 (.) 45 95 55 95 235 () 34 342 (.5) 00 25 70 20 255 (.) 95 25 55 65 75 92 420 (.9) 75 90 0 205 295 (.3) 25 (0.) 00 80 235 () 290 (.3) 34 342 (.5) 05 75 25 () 95 70 230 () 35 85 35 220 () 275 (.2) 225 () 280 (.2) 20 245 (.) 80 65 275 (.2) 45 230 () 40 40 40 40 40 65 0 75 20 65 95 40 40 00 50 50 50 80 45 85 225 () 35 220 () 325 (.4) 240 (.) 305 (.4) 200 05 20 75 50 204 30 08 78 245 (.) 60 200 295 (.3) 200 230 () 40 70 00 70 00 48 88 225 () 0 320 (.4) 395 (.8) 260 (.2) 305 (.4) 200 45 60 45 50 70 00 0 80 60 70 245 (.) 60 200 295 (.3) 200 230 () 00 30 90 240 (.) 280 (.2) 95 25 200 200 200 92 420 (.9) 50 90 225 () 0 320 (.4) 395 (.8) 260 (.2) 305 (.4) 70 90 70 05 45 60 45 50 35-80 60 35 60 -. Fasteners must not be driven until the concrete has reached the minimum designated compressive strength. 2. Concrete thickness must be a minimum of three times the embedment depth. 3. The allowable tension and shear values are for fasteners only. Steel or wood members connected the substrate must be investigated for compliance with the applicable code. 4. The values listed above are allowable load capacities. The values are based on minimum required facrs of safety. Consideration of additional safety facrs may be necessary depending on the application, such as life safety or overhead. 5. Multiple fasteners are recommended for any attachment for increased reliability. www.powers.com Canada: (905) 673-7295 or (54) 63-426 Powers USA: (800) 524-3244 or (94) 235-6300
PROUCT INFORMATION Performance ata PERFORMANCE ATA Ultimate Load Capacities for Powder Actuated Fasteners in Lightweight Concrete,2,3,4,6 Pin escription Ballistic Point Pin (0.50" Shank) Ballistic Point Pin (0.8"/0.50" Shank) 0.300" Head rive Pin 8mm Head rive Pin (0.45" Shank) /4"-20 Threaded Stud (0.45" Shank) 3/8" Head rive Pin (0.72" Shank) 0mm Head rive Pin 5 (0.77" Shank) 3/8"-6 Threaded Stud (0.205" Shank) Minimum Embedment epth h v in. (mm) (9.) -/4 (3.8) -/2 (38.) (9.) -/4 (3.8) -/2 (38.) -/4 (3.8) -/4 (3.8) -/2 (38.) -/4 (3.8) 3/8 (34.9) -/2 (38.) -5/8 (4.3) /4 (3.8) 3,000psi Lightweight Concrete Minimum Concrete Compressive Strength (f' c ) 3,000psi Lightweight Concrete, Over 20 Gage eck Lower Flute Upper Flute Top of Slab Ultimate Load Capacities for Powder Actuated Fastener Ceiling Clips in Lightweight Concrete,2,3,4,6 Pin escription Ceiling Clips - w/ 0.300" Head Pin (0.45" Shank) Economy Ceiling Clips w/ 0.300" Head Pin (0.45" Shank) Ballistic Point Ceiling Clip (0.8"/0.50" Shank) Ceiling Clips - LA Pin (0.52" Shank) Minimum Embedment epth h v in. (mm) (9.) /8 (28.6) (9.) (9.) /8 (28.6) 560 (2.5) 600 350 (.6),30 (5.8) 350 (.6),30 (5.8) 570,000 550,350 550,350 (2.5) (4.4) (2.4) (6) (2.4) (6) 80,220 700,380 700,380 (3.6) (5.4) (3.) (6.) (3.) (6.),040,440 840,400 840,400 (4.6) (6.4) (3.7) (6.2) (3.7) (6.2) 445 465 (2) (2.) 350 625 600,450 880,450,000,075 (.6) (2.8) (6.4) (3.9) (6.4) (4.4) (4.8) 650 900 960,695,45,695,250,525 (2.9) (4) (4.3) (7.5) (6.3) (7.5) (5.6) (6.8) 650 900,90,895,90,895,700,875 (2.9) (4) (5.3) (8.4) (5.3) (8.4) (7.6) (8.3) 350 625 350 850 350 850 (.6) (2.8) (.6) (3.8) (.6) (3.8) 650 900 525 875 525 875 (2.9) (4) (2.3) (3.9) (2.3) (3.9) 650,540 620,830,45,830 (2.9) (6.9) (2.8) (8.) (6.3) (8.),20,620 860,930 860,930 (5.4) (7.2) (3.8) (8.6) (3.8) (8.6),50,200 875,475,45,865 (5.) (5.3) (3.9) (6.6) (6.3) (8.3),575,575,025,575,025,575 (7) (7) (4.6) (7) (4.6) (7),850,850,75,700,75,700 (8.2) (8.2) (5.2) (7.6) (5.2) (7.6) 2,400 2,325,325,800 2,330 3,30 (5.9) (8) (3.9) 350-650 350-825 350 825 (.6) (2.9) (.6) (3.7) (.6) (3.7) 850 -,325 425 -,25 425,25 (3.8) (5.9) (.9) (5) (.9) (5) 250 (.) 300 (.3) 300 (.3) 250 (.) 300 (.3) 3,000psi Lightweight Concrete 45 200 200 200 225 () 450 (2) Minimum Concrete Compressive Strength (f' c ) 400 (.8) 400 (.8) 400 (.8) 400 (.8) 400 (.8) 200 225 () 605 200 225 () - 300 (.3) 475 (2.) 525 (2.3) 725 (3.2) 440 (2) 3,000psi Lightweight Concrete, Over 20 Gage eck Lower Flute Upper Flute 45 200 350 (.6) 350 (.6) 200 225 () 600 600 600 600 600 -,300 (5.8) 400 (.8) 625 (2.8) 200 225 () 680 (3) 200 225 () 300 (.3) 440 (2) 600 600 600 600 600,300 (5.8) 625 (2.8). Fasteners must not be driven until the concrete has reached the minimum designated compressive strength. 2. Concrete thickness must be a minimum of three times the embedment depth. 3. The ultimate tension and shear values are for fasteners only. Steel or wood members connected the substrate must be investigated for compliance with the applicable code. 4. The values listed above are ultimate load capacities which should be reduced by a facr of safety determine the allowable working load. For allowable load capacities, see the allowable load tables. 5. The shear load listed is perpendicular the flute. The shear value parallel the flute is 2,025 lbs (9. kn). 6. Multiple fasteners are recommended for any attachment for increased reliability. Powers USA: (800) 524-3244 or (94) 235-6300 Canada: (905) 673-7295 or (54) 63-426 www.powers.com 2
Performance ata PROUCT INFORMATION PERFORMANCE ATA Allowable Load Capacities for Powder Actuated Fasteners in Lightweight Concrete,2,3,4,6 Pin escription Ballistic Point Pin (0.50" Shank) Ballistic Point Pin (0.8"/0.50" Shank) 0.300" Head rive Pin 8mm Head rive Pin (0.45" Shank) /4"-20Threaded Stud (0.45" Shank) 3/8" Head rive Pin (0.72" Shank) 0mm Head rive Pin 5 (0.77" Shank) 3/8"-6Threaded Stud (0.205" Shank) Pin escription Ceiling Clips - w/ 0.300" Head Pin (0.45" Shank) Economy Ceiling Clips - w/ 0.300" Head Pin (0.45" Shank) Ballistic Point Ceiling Clip (0.8"/0.50" Shank) Ceiling Clips - LA Pin (0.52" Shank) Minimum Embedment epth h v in. (mm) (9.) /4 (3.8) /2 (38.) (9.) /4 (3.8) /2 (38.) /4 (3.8) /4 (3.8) /2 (38.) /4 (3.8) 3/8 (34.9) /2 (38.) 5/8 (4.3) /4 (3.8) Minimum Embedment epth h v in. (mm) (9.) /8 (28.6) (9.) (9.) /8 (28.6) 3,000psi Lightweight Concrete Minimum Concrete Compressive Strength (f' c ) 3,000psi Lightweight Concrete, Over 20 Gage eck Lower Flute Upper Flute Top of Slab 60 75 45 60 45 60 70 25 70 65 70 65 00 55 85 70 85 70 30 80 05 75 05 75 70 70 70 25 20 290 75 290 200 25 (.3) (.3) () 30 80 90 340 280 340 250 305 (.5) (.2) (.5) (.) (.4) 30 80 235 380 235 380 340 375 () (.7) () (.7) (.5) (.7) 70 35 35 60 35 60 70 25 65 70 65 70 65 95 35 225 35 225 () () 55 205 05 240 05 240 (.) (.) 95 205 75 295 285 425 (.3) (.3) (.9) 35 35 205 35 205 35 (.4) (.4) (.4) (.4) 370 370 235 340 235 340 (.6) (.6) () (.5) () (.5) 40 395 265 360 35 485 (.8) (.8) (.2) (.6) (.4) (2.2) 70 30 45 65 45 65 70 265 85 225 85 225 (.2) () () Allowable Load Capacities for Powder Actuated Fastener Ceiling Clips in Lightweight Concrete,2,3,4,6 3,000psi Lightweight Concrete 45 Minimum Concrete Compressive Strength (f' c ) 50 40 25 (0.) 35 60 40 80 45 60 40 80 20 35 45 30 30 (0.) (0.) 55 90 5 55-60 95 05 45 55 3,000psi Lightweight Concrete, Over 20 Gage eck Lower Flute Upper Flute 45 40 20 70 20 70 20 40 35 45 35-260 (.2) 80 25. Fasteners must not be driven until the concrete has reached the minimum designated compressive strength. 2. Concrete thickness must be a minimum of three times the embedment depth. 3. The tension and shear values are for fasteners only. Steel or wood members connected the substrate must be investigated for compliance with the applicable code. 4. The values listed above are allowable load capacities. The values are based on minimum required facrs of safety. Consideration of additional safety facrs may be necessary depending on the application, such as life safety or overhead. 5. The shear load listed is perpendicular the flute. The shear value parallel the flute is 35 lbs (.4 kn). 6. Multiple fasteners are recommended for any attachment for increased reliability. 35 45 35 30 (0.) 55 60 55 20 20 20 35 35 260 (.2) 25 3 www.powers.com Canada: (905) 673-7295 or (54) 63-426 Powers USA: (800) 524-3244 or (94) 235-6300
PROUCT INFORMATION Performance ata PERFORMANCE ATA Ultimate Load Capacities for Powder Actuated Fasteners used Install Sill Plates on Normal-Weight Concrete,2 Pin escription Ballistic Point Pin 0.300" / 8mm Head rive Pin or /4"-20 Threaded Stud (0.45" Shank) 3/8" Head rive Pin (0.72" Shank) Minimum Embedment epth h v in. (mm) /2 (38.) /2 (38.) /2 (38.) Minimum Concrete Compressive Strength (f'c) f'c 2,000 psi (3.8 (MPa) Perpendicular Concrete,060 (4.7) 900 (4.0) 960 (4.3) Parallel Concrete,200 (5.3),50 (5.),50 (5.). The values listed above are ultimate load capacities which should be reduced by a minimum facr of safety of 5.0 or greater determine the allowable working load. Consideration of safety facrs of 0 or higher may be necessary depending on the application, such as life safety or overhead. 2. Multiple fasteners are recommended for any attachment for increased reliability. 920 (4.) 600 900 (4.0) Ultimate Load Capacities for Powder Actuated Fasteners in ASTM A36 Steel,2,3,5 Pin escription Ballistic Point Pin (0.50" Shank) 0.300" Head rive Pin 8mm Head rive Pin (0.45" Shank) 8mm head CSI Pin (0.57" Shank) /4"-20 Threaded Stud (0.45" Shank) 3/8" Head rive Pin (0.72" Shank) 0mm Head rive Pin (0.77" Shank) 3/8"-6 Threaded Stud (0.205" Shank) Ceiling Clips w/ 0.300" Head Pin (0.45" Shank) Economy Ceiling Clips w/ 0.300" Head Pin (0.45" Shank) Ceiling Clips - LA Pin (0.52" Shank) Shank Type Smooth Knurled Smooth Spiral Knurled Knurled Smooth Smooth Knurled Smooth Smooth Smooth 590 (2.6),00 (4.9) 865 (3.8) Nominal Steel Thickness /8" 3/6" /4" 3/8" /2" 4 2,090 (9.3) 990 (4.4),325 (5.9) 90 (4.0),705 (7.6),775 (7.9) 3,030 (3.5) 3,050 (3.6) 2,825 (2.6),560 (6.9) 2,240 (0.0) 2,050 (9.) 4,80 (2.4),00 (4.9) 950 (4.2) 2,230 (9.9) 2,700 (2.0),630 (7.3),490 (6.6) 850 (3.8),20 (5.0),030 (4.6) 950 (4.2),80 (5.2) 2,770 (2.3),90 (5.3),290 (5.7),200 (5.3) 2,700 (2.0),090 (4.8),090 (4.8),80 (5.2) 2,770 (2.3) 3,700 (6.5) 4,50 (8.5) 5,460 (24.3),90 (5.3),290 (5.7),200 (5.3) 2,60 (9.6),820 (8.),300 (5.8) 3,730 (6.6),090 (4.8),090 (4.8),80 (5.2) 2,730 (2.) 2,800 (2.5) 2,800 (2.5) 3,99 (4.2) 3,300 (4.7) 3,890 (7.3) 4,50 (8.5) 8,090 (36.0),90 (5.3),290 (5.7),200 (5.3) 2,250 (0.0) 2,600 (.6) 2,40 3,390 (5.) 2,560 (.4) 3,020 (3.4),900 (8.5) 2,625 (.7) 3,025 (3.5) 2,620 (.7) 2,925 (3.0) 3,760 (6.7) 4,230 (8.8) 4,400 (9.6) 2,650 (.8),970 (8.8) 2,675 (.9) 2,875 (2.8) 2,600 (.6) 2,825 (2.6) 3,675 (6.3) 4,075 (8.),090 (4.8),090 (4.8),80 (5.2),90 (5.3),290 (5.7),200 (5.3). The ultimate tension and shear values are for fasteners only. Steel or wood members connected the substrate must be investigated for compliance with the applicable code. 2. The values listed above are ultimate load capacities which should be reduced by a facr of safety determine the allowable working load. For allowable load capacities, see the allowable load tables. 3. Fasteners must be driven obtain an embedment equivalent the nominal steel thickness with the point of the fastener penetrating through the steel base material. 4. Fasteners must be driven obtain a minumum embedment of /2". The point of the fastener does not need penetrate through the steel base material. 5. Multiple fasteners are recommended for any attachment for increased reliability. Powers USA: (800) 524-3244 or (94) 235-6300 Canada: (905) 673-7295 or (54) 63-426 www.powers.com 4
Performance ata PROUCT INFORMATION PERFORMANCE ATA Allowable Load Capacities for Powder Actuated Fasteners in ASTM A36 Steel,2,3,5 Pin escription Ballistic Point Pin (0.50" Shank) 0.300" Head rive Pin 8mm Head rive Pin (0.45" Shank) 8mm head Spiral CSI Pin (0.57" Shank) /4"-20 Threaded Stud (0.45" Shank) 3/8" Head rive Pin (0.72" Shank) 0mm Head rive Pin (0.77" Shank) 3/8"-6 Threaded Stud (0.205" Shank) Ceiling Clips - w/ 0.300" Head Pin (0.45" Shank) Economy Ceiling Clips w/ 0.300" Head Pin (0.45" Shank) Ceiling Clips - LA Pin (0.52" Shank) Shank Type Smooth Knurled Smooth Spiral Knurled Knurled Smooth Smooth Knurled Smooth Smooth Smooth 20 220 (.0) 70 280 (.2) 220 (.0) 90 Nominal Steel Thickness /8" 3/6" /4" 3/8" /2" 4 420 (.9) 200 265 (.2) 540 (2.4) 445 (2.0) 540 (2.4) 80 340 (.5) 355 (.6) 55 (2.3) 325 (.4) 300 (.3) 95 225 555 540 (.0) (2.5) (2.4) 205 240 220 (.) (.0) 90 260 20 (.2) 235 (.0) 240 (.) 240 (.). The allowable tension and shear values are for fasteners only. Steel or wood members connected the substrate must be investigated for compliance with the applicable code. 2. The values listed above are allowable load capacities. The values are based on minimum required facrs of safety. Consideration of additional safety facrs may be necessary depending on the application, such as life safety or overhead. 3. Fasteners must be driven obtain an embedment equivalent the nominal steel thickness with the point of the fastener penetrating through the steel base material. 4. Fasteners must be driven obtain a minumum embedment of /2". The point of the fastener does not need penetrate through the steel base material.5. Multiple fasteners are recommended for any attachment for increased reliability. 5. Multiple fasteners are recommended for any attachment for increased reliability. 605 60 565 (2.5) 585 (2.6) 555 (2.5) 740 (3.3) 545 (2.4),090 (4.8) 240 (.) 260 (.2) 240 (.) 30 (.4) 445 (2.0) 40 (.8) 735 (3.3) 430 (.9) 365 (.6) 50 745 (3.3) 220 (.0) 20 235 (.0) 545 (2.4) 560 (2.5) 560 (2.5) 535 (2.4) 660 (2.9) 780 (3.5) 545 (2.4) 620 (2.8) 240 (.) 260 (.2) 240 (.) 450 (2.0) 520 (2.3) 465 (2.) 65 50 (2.3) 605 245 (.) 525 (2.3) 605 390 (.7) 495 (2.2) 750 (3.3) 845 (3.8) 755 (3.4) 490 (2.2) 390 (.7) 535 (2.4) 575 (2.6) 520 (2.3) 565 (2.5) 640 (2.8) 600 220 (.0) 20 235 (.0) 240 (.) 260 (.2) 240 (.) 5 www.powers.com Canada: (905) 673-7295 or (54) 63-426 Powers USA: (800) 524-3244 or (94) 235-6300
PROUCT INFORMATION Performance ata PERFORMANCE ATA Ultimate Load Capacities for Powder Actuated Fasteners in ASTM A572 Steel,2,3,5 Pin escription 0mm Head rive Pin (0.77" Shank) 8mm head CSI Pin (0.57" Shank) Shank Type Smooth Spiral Knurled,275 (5.7),625 (7.2) Nominal Steel Thickness /8" 3/6" /4" 3/8" /2" 4 3,850 (7.) 2,550 (.3),075 (4.8) 2,750 (2.2) 3,250 (4.5) 3,50 (4.0). The ultimate tension and shear values are for fasteners only. Steel or wood members connected the substrate must be investigated for compliance with the applicable code. 2. The values listed above are ultimate load capacities which should be reduced by a facr of safety determine the allowable working load. For allowable load capacities, see the allowable load tables. 3. Fasteners must be driven obtain an embedment equivalent the nominal steel thickness with the point of the fastener penetrating throug the steel base material. 4. 8mm head CSI pin and 0mm head drive pin fasteners must be driven obtain a minumum embedment of /2". The point of the fastener does not need penetrate through the steel base material. 5. Multiple fasteners are recommended for any attachment for increased reliability.,800 (8.0) 3,975 (7.7) 3,900 (7.3) 2,900 (2.9) 2,275 (0.) 3,300 (4.7) 4,250 (8.9) 2,675 (.9) 2,900 (2.9) 3,050 (3.6) Allowable Load Capacities for Powder Actuated Fasteners in ASTM A572 Steel,2,3,5 Pin escription 0mm Head rive Pin (0.77" Shank) 8mm head CSI Pin (0.57" Shank) Shank Type Smooth Spiral Knurled 255 (.) 325 (.4) Nominal Steel Thickness /8" 3/6" /4" 3/8" /2" 4 770 (3.4) 50 (2.2) 25 (.0) 550 (2.4). The allowable tension and shear values are for fasteners only. Steel or wood members connected the substrate must be investigated for compliance with the applicable code. 2. The values listed above are allowable load capacities. The values are based on minimum required facrs of safety. Consideration of additional safety facrs may be necessary depending on the application, such as life safety or overhead. 3. Fasteners must be driven obtain an embedment equivalent the nominal steel thickness with the point of the fastener penetrating throug the steel base material. 4. 8mm head CSI pin and 0mm head drive pin fasteners must be driven obtain a minumum embedment of /2". The point of the fastener does not need penetrate through the steel base material. 5. Multiple fasteners are recommended for any attachment for increased reliability. 650 (2.9) 630 (2.8) 295 (.3) 795 (3.5) 735 (3.3) 580 (2.6) 355 (.6) 660 (2.9) 785 (3.5) 535 (2.4) 580 (2.6) 60 Ultimate Load Capacities for Powder Actuated Fasteners in Masonry (f m,500),2,3,4 Pin escription Ballistic Point Pin (0.8"/0.50" Shank).300"/8mm Head rive Pin or /4"-20 Threaded Stud (0.45"Shank) 3/8" Head rive Pin (0.72" Shank) 3/8"- 6 Threaded Stud (0.205" Shank) Minimum Embed. epth hv in. (mm) Hollow CMU Grout-filled Concrete Masonry Face Face Mortar Joint 320 (.4) 740 (3.3) 570 (2.6) 900 (4.) 50 (2.3) 960 (4.3) 320 (.4) 740 (3.3) 570 (2.6) 900 (4.) 50 (2.3) 960 (4.3) 740 (3.3) 850 (3.8) 60 670 (3.0) 860 (3.9),460 (6.6),060 (4.8),030 (4.6). Successful fastening the face shell of Hollow CMU is typically done with the lightest powder load level. 2. The values listed above are ultimate load capacities which should be reduced by a facr of safety determine the allowable working load. For allowable load capacities, see the allowable load tables. 3. Multiple fasteners are recommended for any attachment for increased reliability. 4. Concrete masonry units are typical 8 x 8 x 6 inch units meeting the requirements of ASTM C90, Grade N, lightweight block. Powers USA: (800) 524-3244 or (94) 235-6300 Canada: (905) 673-7295 or (54) 63-426 www.powers.com 6
Performance ata PROUCT INFORMATION PERFORMANCE ATA Allowable Load Capacities for Powder Actuated Fasteners in Masonry (f m,500),2,3,4 Pin escription 0.300" / 8mm Head rive Pin or /4"-20 Threaded Stud (0.45" Shank) 3.8" Head rive Pin (0.72" Shank) 3/8"-6 Threaded Stud (0.205" Shank) Pin escription Head/Shank iameter 8mm Top Hat Pin 0.35"/0.45" Minimum Embedment epth hv in. (mm). Successful fastening the face shell of Hollow CMU is typically done with the lightest powder load level. 2. The values listed above are allowable load capacities. The values are based on minimum required facrs of safety. Consideration of additional safety facrs may be necessary depending on the application, such as life safety or overhead. 3. Multiple fasteners are recommended for any attachment for increased reliability. 4. Concrete masonry units are typical 8 x 8 x 6 inch units meeting the requirements of ASTM C90, Grade N, lightweight block. Ultimate and Allowable Tensile Pullover Capacities for Light Steel Framing with Powder-Actuated Fasteners,2,3 35 Hollow CMU Grout-Filled Concrete Masonry Cell Cell Mortar Joint Minimum Thickness of Sheet Steel or Framing Member 6 Gage 8 Gage 20 Gage 22 Gage 25 Gage Ultimate Allowable Ultimate Allowable Ultimate Allowable Ultimate Allowable Ultimate Allowable 2,650 530 2,470 495,20 240 895 80 580 5 (.9) (2.4) (.) (2.2) (5.4) (.) (4.0) (2.6) 8mm Pin 0.35"/0.45",470 295,050 20 730 45 45 85 without Washer 0.35"/0.57" (6.6) (.3) (4.7) (3.3) (.9) 8mm Pin with 0.35"/0.45",575 30,85 235 990 200 795 60 " Washer (7.) (.4) (5.3) (.) (4.5) (3.6).300" Pin with 0.300"/0.45" 790 60 645 30 500 00 7/8" washer (3.6) (2.9) (2.3) 0mm Pin 2,330 465,750 350,85 235 890 80 590 20 without Washer 0.390"/0.77" (2.) (7.9) (.6) (5.3) (.) (4.0). Tabulated allowable pullover load values were tested in accordance with ICC-ES AC70 and are based on an applied safety facr of 5.0. 2. Allowable pullover capacities of sheet steel or framing member should be compared the fastener tensile load capacities in concrete, steel and masonry determine the controlling resistance load. 3. For pins with washer assemblies, the washer thickness is 4 gage minimum. 95 20 (0.) 85 65 95 0 5 05 85 55 20 35 30 7 www.powers.com Canada: (905) 673-7295 or (54) 63-426 Powers USA: (800) 524-3244 or (94) 235-6300
PROUCT INFORMATION Fasteners.300" Head rive Pins PROUCT ESCRIPTION rive pins with a.300" head are designed for permanently fastening a fixture concrete, some types of concrete block, and A36 or A572 structural steel. The pins are formed with a 0.45" diameter shank in various lengths, and a specially designed point allow proper penetration in typical base materials. Knurled shank designs are available increase performance in steel base materials. A plastic flute is mounted over the point retain the drive pin in the fastener guide of the ol providing guidance during the driving operation. Blue Magic TM pins offer a hard plastic flute for improved centering in the ol and tip protection. FASTENERS SIZES.300" Head rive Pins Cat. No. Shank Length Shank iameter Standard Box Standard Carn Wt./00 5002 /2" (K) 0.45" 00 5,000 0.4 5006 5/8" (K) 0.45" 00 5,000 0.5 50022 " 0.45" 00 5,000 0.5 50026 " 0.45" 00 5,000 0.7 50032 /4" 0.45" 00,000 0.8 50034 /2" 0.45" 00,000.0 50038 2" 0.45" 00,000.2 50040 2 /4" 0.45" 00,000.3 50044 2 /2" 0.45" 00,000.5 50048 3" 0.45" 00,000.8 (K) = knurled.300" Head rive Pins Master Pack Cat. No. Shank Length Shank iameter Standard Box Standard Carn Wt./00 50980 /2" (K) 0.45",000 5,000 0.4 53300 5/8" (K) 0.45",000 5,000 0.5 5040 " 0.45",000 5,000 0.5 500 " 0.45",000 5,000 0.7 560 /4" 0.45",000 5,000 0.8 5340 /2" (K) TopHat 0.45",000 5,000 0.6 5400 " Top Hat 0.45",000 5,000 0.7 (K) = knurled.300" Head Step Shank rive Pins Cat. No. Shank Length Shank iameter Standard Box Standard Carn Wt./00 5058* " Step Shank 0.45/0.30" 00 5,000 0.5 5059* " Step Shank 0.45/0.30" 00 5,000 0.6 * iscontinued item once current sck exhausted..300" Head Blue Magic TM rive Pins Cat. No. Shank Length Shank iameter Standard Box Standard Carn Wt./00 56000* /2" 0.45" 00 5,000 0.9 5602* /2" 0.45" 00 5,000 0.9 * iscontinued item once current sck exhausted. Powers USA: (800) 524-3244 or (94) 235-6300 Canada: (905) 673-7295 or (54) 63-426 www.powers.com 8
Fasteners PROUCT INFORMATION.300" Head rive Pins with Top Hat PROUCT ESCRIPTION These pins are used primarily for applications fastening drywall track concrete or steel. Pins are assembled with a metal p hat provide faster insertion in the driving ol with reduced possibility of pricking a finger during load and provide extra bearing surface against the drywall track. FASTENERS SIZES Cat. No. Shank Length Shank iameter Standard Box Standard Carn Wt./00 5036 /2" (K) 0.45" 00 5,000 0.6 5038 5/8" (K) 0.45" 00 5,000 0.7 5040 " 0.45" 00 5,000 0.7 5044 " 0.45" 00 5,000 0.8 (K) = knurled.300" Head rive Pins with Washers PROUCT ESCRIPTION To provide resistance pullover, these pins are available with preassembled 4 gage (0.075") metal washers in various diameters. Resistance pullover is increased by the additional bearing surface provided by the washer. The insulation washer has a thickness of 0.035". FASTENERS SIZES.300" Head rive Pins with " Washer Cat. No. Shank Length Shank iameter Standard Box Standard Carn Wt./00 50070 " 0.45" 00,000.5 50080 2 /2" 0.45" 00,000 2.5.300" Head rive Pins with 7/8" Washer Cat. No. Shank Length Shank iameter Standard Box Standard Carn Wt./00 50090 " 0.45" 00,000 2.0 50092 /4" 0.45" 00,000 2. 50094 /2" 0.45" 00,000 2.2 50096 2" 0.45" 00,000 2.5 50098 2 /2" 0.45" 00,000 2.7 5000 3" 0.45" 00,000 3.3.300" Head rive Pins with " Washer Cat. No. Shank Length Shank iameter Standard Box Standard Carn Wt./00 5008 /4" 0.45" 00,000 2.5 500 /2" 0.45" 00,000 2.6 502 2" 0.45" 00,000 2.9 504 2 /2" 0.45" 00,000 3.3 506 3" 0.45" 00,000 3.6.300" Head rive Pins with 7/6" Insulation Washer Cat. No. Shank Length Shank iameter Standard Box Standard Carn Wt./00 5022 /2" 0.45" 00,000 2.5 5026 2 /2" 0.45" 50 500 3.2 9 www.powers.com Canada: (905) 673-7295 or (54) 63-426 Powers USA: (800) 524-3244 or (94) 235-6300
PROUCT INFORMATION Fasteners Mechanically Galvanized (MG) rive Pins for Pressure Treated Lumber PROUCT ESCRIPTION The Powers MG powder actuated fasteners are designed with mechanically galvanized coating in accordance with ASTM B695, Class 55 for fastening through pressure treated lumber in concrete and grout-filled concrete masonry. These drive pins provide an equivalent solution for code compliant wood concrete fastening applications and are available with a round washer for increased pullover resistance. FASTENERS SIZES.300" Head MG Pin (No Washer) Cat. No. Shank Length Shank iameter Standard Box Standard Carn Wt./00 50034MG /2" 0.45" 00,000.0 50038MG 2" 0.45" 00,000.2 50045MG 2 /2" 0.45" 00,000.5 50047MG 3" 0.45" 00,000.6.300" Head MG Pin with " Round Washer Cat. No. Shank Length Shank iameter Standard Box Standard Carn Wt./00 500MG /2" 0.45" 00,000 2.3 502MG 2" 0.45" 00,000 2.6 503MG 2 /2" 0.45" 00,000 3.0 505MG 3" 0.45" 00,000 3.3 Powers USA: (800) 524-3244 or (94) 235-6300 Canada: (905) 673-7295 or (54) 63-426 www.powers.com 20
Fasteners PROUCT INFORMATION 8mm Head rive Pins PROUCT ESCRIPTION rive Pins with a 8mm head are designed for permanently fastening a fixture concrete, some types of masonry, and A36 or A572 structural steel. The pins are manufactured with a 0.45" diameter shank in various lengths. Knurled shank designs are available increase performance in steel base materials. A 8mm plastic washer is mounted over the point retain the drive pin in the fastener guide of the ol providing centered guidance during the driving operation. FASTENERS SIZES 8mm Head rive Pins Cat. No. Shank Length Shank iameter Standard Box Standard Carn Wt./00 5080 6mm (K)-5/8" 0.45" 00 5,000 0.4 5082 9mm (K)-" 0.45" 00 5,000 0.5 5084 22mm-7/8" 0.45" 00 5,000 0.6 5086 27mm-" 0.45" 00 5,000 0.7 5088 32mm- /4" 0.45" 00,000 0.8 5090 37mm- /2" 0.45" 00,000 0.9 5092 42mm- 5/8" 0.45" 00,000.0 5094 47mm- 7/8 0.45" 00,000. 5096 52mm-2" 0.45" 00,000.3 5098 57mm-2 /4" 0.45" 00,000.4 50200 62mm-2 /2" 0.45" 00,000.5 50202 72mm-2 7/8" 0.45" 00,000.6 (K) = knurled 8mm Head rive Pins with Top Hat These pins are used primarily for applications fastening drywall track concrete or steel. They are assembled with a metal p hat provide faster insertion in the driving ol with reduced possibility of pricking a finger during loading and provide extra bearing surface against the drywall track. Cat. No. Shank Length Shank iameter Standard Box Standard Carn Wt./00 5020 6mm (K)-5/8" 0.45" 00 5,000 0.6 5024 22mm-7/8" 0.45" 00 5,000 0.7 5026 27mm-" 0.45" 00 5,000 0.8 (K) = knurled 8mm Head iameter rive Pins with Top Hat Master Pack Cat. No. Shank Length Shank iameter Standard Box Std. Carn Wt./00 5700 6mm (K)-5/8"TH 0.45",000 5,000 0.6 5750 22mm 7/8 TH 0.45",000 5,000 0.7 8mm Head rive Pins with Washers FASTENERS SIZES 8mm Head rive Pins with " Washer To provide resistance pullover, these pins are available with preassembled 4 gage (0.075") metal washers in various diameters. Resistance pullover is increased by the additional bearing surface provided by the washer. Cat. No. Shank Length Shank iameter Standard Box Standard Carn Wt./00 50220 27mm-" 0.45" 00,000 2.5 50222 32mm- /4" 0.45" 00,000 2.5 50224 37mm- /2" 0.45" 00,000 2.6 50226 52mm-2" 0.45" 00,000 2.9 50228 62mm-2 /2" 0.45" 00,000 3. 50230 72mm-2 7/8" 0.45" 00,000 3.3 2 www.powers.com Canada: (905) 673-7295 or (54) 63-426 Powers USA: (800) 524-3244 or (94) 235-6300
FASTENERS SIZES 8mm Head Collated rive Pins PROUCT INFORMATION Cat. No. Shank Length Shank iameter Standard Box Standard Carn 50240N 6mm- 5/8" (K) 0.45" 500 2,500 50242N 9mm- " (K) 0.45" 500 2,500 50244N 9mm- " 0.45" 500 2,500 50248N 27mm-" 0.45" 500 2,500 50250N 32mm- /4" 0.45" 500 2,500 50252N 37mm- /2" 0.45" 500 2,500 50254N 42mm- 5/8" 0.45" 500 2,500 50256N 47mm- 7/8" 0.45" 500 2,500 50258N 52mm-2" 0.45" 500 2,500 50260N 57mm-2 /4" 0.45" 500 2,500 50262N 62mm-2 /2" 0.45" 500 2,500 50264N 72mm-2 7/8" 0.45" 500 2,500 (K) = knurled - Use with PA35, X350, X460. The PA35 and X350 have a maximum pin length capacity of 42mm (-5/8). Longer length pins are suitable for the X460. Fasteners 8mm Head Spiral CSI Pins FASTENERS SIZES 8mm Head Spiral CSI Pins The pins were designed provide premium performance in concrete and steel base materials. The pins are manufactured with a 0.57 diameter shank in various lengths and with a spiral knurling for consistent optimized performance in concrete and steel (including I-Beams). Cat. No. Shank Length Shank iameter Standard Box Standard Carn 5020 5/8 (K) 0.57 00 000 50203 (K) 0.57 00 000 50204 7/8 (K) 0.57 00 000 50205 (K) 0.57 00 000 50207 -/2 (K) 0.57 00 000 5027-5/8 (K) 0.57 00 000 50208 -/4 (K) 0.57 00 000 50209 2 (K) 0.57 00 000 502 2-7/8 (K) 0.57 00 000 (K)- Knurled 8mm Head Spiral CSI Collated Pins Cat. No. Shank Length Shank iameter Standard Box Standard Carn 50450 50452 50454 50456 50458 50460 5046 50462 50464 (K)- Knurled 5/8 (K) (K) 7/8 (K) (K) -/4 (K) -/2 (K) -5/8 (K) 2 (K) 2-7/8 (K) 0.57 0.57 0.57 0.57 0.57 0.57 0.57 0.57 0.57 500 500 500 500 500 500 500 500 500 8mm Head Collated rive Pins PROUCT ESCRIPTION 8mm head collated drive pins are designed for production fastening in concrete and steel. The pins are collated in plastic strips of ten fasteners each which provide a semi-aumatic feed and centering guidance during the driving operation. Each pin has a 0.45" diameter shank available in various lengths. A knurled shank design is standard on shorter lengths increase performance in steel base materials. 2,500 2,500 2,500 2,500 2,500 2,500 2,500 2,500 2,500 Powers USA: (800) 524-3244 or (94) 235-6300 Canada: (905) 673-7295 or (54) 63-426 www.powers.com 22
Fasteners PROUCT INFORMATION 0mm Head rive Pins PROUCT ESCRIPTION rive Pins with a 0mm head are designed for permanently fastening a fixture concrete, some types of masonry, and A36 or A572 structural steel. The pins are manufactured with a 0.77 diameter shank in various lengths. A 0 mm plastic washer is mounted over the point retain the drive pin in the fastener guide of the ol providing centered guidance during the driving operation. FASTENERS SIZES 0mm Head rive Pins Cat. No. Shank Length Shank iameter Standard Box Standard Carn 50846 9mm-" 0.77" 00,000 50848 22mm-7/8" 0.77" 00,000 50850 27mm-" 0.77" 00,000 50852 32mm- /4" 0.77" 00,000 50854 42mm- 5/8" 0.77" 00,000 50856 52mm-2" 0.77" 00,000 50858 62mm-2 /2" 0.77" 00,000 50860 72mm-2 7/8" 0.77" 00,000 50862 82mm-3 /4" 0.77" 00,000 TM Ballistic Point rive Pins PROUCT ESCRIPTION Premium drive pins with a 0.300" head have a specially designed point allow more consistent penetration in harder base materials and will reduce failures in dense concrete and steel. rive Pins are manufactured with 0.50" diameter shank and a 0.8" step shank in various lengths. A plastic flute is mounted over the point retain the drive pin in the fastener guide of the ol providing guidance during the driving operation. Ballistic Point rive Pins are ideal for fastening steel and hard concrete. Standard powder actuated pins fasten inconsistently in steel and harder concrete base materials. Ballistic Point rive Pins have a unique pointed tip for more consistent performance. Pin penetration in difficult base materials is improved due a rolled manufacturing process and a black coating applied the pin. FASTENERS SIZES Ballistic Point TM rive Pins (Black) Cat. No. Shank Length Shank iameter Standard Box Standard Carn Wt./00 50052 /2" 0.50" 00,000 0.5 50054 " 0.50" 00,000 0.6 Ballistic Point TM Step Shank rive Pins (Black) Cat. No. Shank Length Shank iameter Standard Box Standard Carn Wt./00 50056 /4" 0.8/0.50" 00 5,000 0.6 50057 7/8" 0.8/0.50" 00,000.5 23 www.powers.com Canada: (905) 673-7295 or (54) 63-426 Powers USA: (800) 524-3244 or (94) 235-6300
PROUCT INFORMATION Fasteners Threaded Studs PROUCT ESCRIPTION Threaded studs are available in /4"- 20 and 3/8"-6 thread diameters with a variety of thread and shank lengths for use in concrete, some types of concrete block, and A36 or A572 structural steel. They are used for applications where it may be desirable remove the fixture, where shimming may be required or for suspending sprinkler systems. The 3/8"-6 threaded studs have FM approval. The shank diameter for the threaded studs is 0.45" for the /4"- 20 diameter and 0.205" for the 3/8"- 6 diameter. Both sizes have a specially designed point allow proper penetration in the base material. Knurled shank designs are available increase performance in steel base materials. A plastic flute is mounted over the point retain the drive pin in the fasteners guide of the ol providing guidance during the driving operation. On the /4"- 20 threaded studs a plaster cap is also provided protect the threads of the fastener during the driving process as well as providing guidance during installation. FASTENERS SIZES /4"- 20 Threaded Studs Cat. No. Thread Length Shank Length Shank ia. Standard Box Std. Carn Wt./00 50322 " /2" (K) 0.45" 00,000. 50326 " " 0.45" 00,000.2 50328 /2" " 0.45" 00,000.2 50330 " " 0.45" 00,000.4 50336 " /4" 0.45" 00,000.5 (K) = knurled 3/8"- 6 Threaded Studs Cat. No. Thread Length Shank Length Shank ia. Standard Box Std. Carn Wt./00 50340 /4" " (K) 0.205" 00,000 3.6 50342 /4" " 0.205" 00,000 3.8 50344 /4" /4" 0.205" 00,000 3.8 (K) = knurled 3/8" Head rive Pins PROUCT ESCRIPTION rive pins with a 3/8" head are designed for permanently fastening a fixture concrete, some types of concrete block, and A36 or A572 structural steel. The pins are formed with a 0.72" diameter shank in various lengths and a specially designed point allow proper penetration in the base material. A plastic flute is mounted over the point retain the drive pin in the fasteners guide of the ol providing guidance during the driving operation. FASTENERS SIZES 3/8" Head rive Pins Cat. No. Shank Length Shank iameter Standard Box Standard Carn Wt./00 5074* 3" 0.72" 00,000 2.5 5076 * 3 /8" (w/ step shank) 0.26/0.88" 00,000 3.4 * iscontinued item once current sck exhausted. Hammer rive Pins PROUCT ESCRIPTION Hammer rive pins are designed for permanently fastening a fixture concrete and some types of concrete block. This fastener is designed for use in a standard hand ol and should not be used in a powder actuated ol. The pins are formed with /4" diameter head on one end, a 0.40" diameter shank in various lengths, and a specially designed point allow proper penetration in the base material. A 3/8" diameter steel washer is mounted over the point retain the drive pin in the fastener guide of the ol and provide guidance during the driving operation. This fastener is recommended for light duty static load applications where holding power is not a critical facr. It should not be used overhead. FASTENERS SIZES /4" Head Hammer rive Pins Cat. No. Shank Length Shank ia. Standard Box Std. Carn Wt./00 50294 " 0.40 00,000 0.6 50296 " 0.40 00,000 0.7 50298 /4" 0.40 00,000 0.8 Hammer rive Setting Tool Cat. No. escription Standard Box Std. Carn 5030 Hammer rive Tool Standard Powers USA: (800) 524-3244 or (94) 235-6300 Canada: (905) 673-7295 or (54) 63-426 www.powers.com 24
Assemblies & Accessories PROUCT INFORMATION Ceiling Clip Assemblies PROUCT ESCRIPTION For acoustical applications and suspended ceiling systems or light fixtures. Several styles of angled clips are pre-mounted on pins..300" Head rive Pins with Ceiling Clips Catalog Shank Shank Wire Standard Standard Number Length iameter Hole Box Carn Wt./00 50364 " 0.45" 0.278" 00,000 3.5 50368* /8" 0.45" 0.278" 00,000 3.0 50370 /4" 0.45" 0.278" 00,000 3.7 50374* /4" 0.45" 0.278" 00,000 3.2 Economy Clip * Economy Clip 8mm Head rive Pins with Ceiling Clips Catalog Shank Shank Wire Standard Standard Number Length iameter Hole Box Carn Wt./00 50272 27mm (") 0.45" 0.278" 00,000 3.5 50274 32mm(-/4") 0.45" 0.278" 00,000 3.7 Catalog Shank Shank Head Wire Standard Standard Number Length iameter iameter Hole Box Carn Wt./00 50206 32mm (-/4 ).77 8mm 0.278 00,000 4.8 8mm Head Spiral CSI rive Pin with Ceiling Clip Cat. No. escription Head ia. Shank ia. Wire Hole Std. Box Std. Ctn. 5022 7/8" CSI with Ceiling Clip 0.300" 0.57" 0.278" 00,000 5023 " CSI with Ceiling Clip 0.300" 0.57" 0.278" 00,000 Ballistic Point rive Pin with Ceiling Clip (45 o ) Cat. No. escription Head ia. Shank ia. Wire Hole Std. Box Std. Ctn. 50366 7/8" with Ceiling Clip 0.300" 0.8"/0.50" 0.278" 00,000 50058 /4" with Ceiling Clip 0.300" 0.8"/0.50" 0.278" 00,000 Pre-Assembled Pin and Clip for LA Tool (45 o ) Catalog Shank Shank Head Wire Standard Standard Number Length iameter iameter Hole Box Carn Wt./00 50438 Pre-assembled Pin & Clip (LA) 0.55" 0.30" 0.278" 00,000 4.5 The assembly is designed for use in a LA type ol. BX and Conduit Clip Assemblies PROUCT ESCRIPTION For the electrical trade, BX and conduit clips are provided in various sizes for attaching conduit base materials where easy removal is not a requirement..300" Head rive Pins with BX Cable Straps Cat. No. Shank Length Shank ia. Standard Box Std. Carn Wt./00 5050 " 0.45" 00,000 3.5.300" Head Pins with Conduit Clips Cat. No. Shank Length Shank ia. Standard Box Std. Carn Wt./00 50382 /2" EMT " Pin 0.45" 00,000 3.3 50384 " EMT /4" 0.45" 00 500 4.6 50385* " EMT " Pin 0.45" 00 500 5.3 50386 " EMT -/8" Pin 0.45" 00 500 4.7 50388* " EMT " Pin 0.45" 25 250 7.2 * With Top Hat 8mm Head rive Pins with Conduit Clips Cat. No. Shank Length Shank ia. Std. Box Std. Carn Wt./00 50276 27mm w/ /2" EMT 0.45" 00,000 3.2 50278 27mm w/ " EMT 0.45" 00 500 3.3 50280 27mm w/ " EMT 0.45" 25 250 6.2 25 www.powers.com Canada: (905) 673-7295 or (54) 63-426 Powers USA: (800) 524-3244 or (94) 235-6300
PROUCT INFORMATION Assemblies & Accessories Rod Hanging PROUCT ESCRIPTION 8mm Head rive Pins with Rod Hanger Clip Catalog Shank Standard Standard Number escription iameter Box Carn 5025 32mm ( /4") CSI Pin with /4"- 20 Rod Hanger 0.57" 00,000 5029 32mm ( /4") Pin with /4"- 20 Rod Hanger 0.45" 00,000 5022 32mm ( /4") Pin with 3/8"- 6 Rod Hanger 0.45" 00,000.300 Head rive Pins with Ceiling & Post Nut Catalog Shank Standard Standard Number escription iameter Box Carn 50376 /8" (29mm) Head Pin with omed Right Angle 0.45" 00,000 Ceiling Clip & Post Nut 50378 /4" (32mm) Head Pin with omed Right Angle 0.45" 00,000 Ceiling Clip & Post Nut Rebar Basket Assemblies PROUCT ESCRIPTION Rebar basket clips are typically used in highway construction and paving applications hold the support baskets for the reinforcing bars in place while the concrete is being poured. 8mm Head rive Pins with Rebar Basket Clip Catalog Shank Standard Standard Number Shank Length iameter Box Carn Wt./00 50702 32mm w/ basket clip 0.45" 00 00 4 50704 37mm w/ basket clip 0.45" 00 00 4. 5072 52mm w/ basket clip 0.45" 00 00 4.4 5076 62mm w/ basket clip 0.45" 00 00 4.6 5078 72mm w/ basket clip 0.45" 00 00 4.8 Forming Pin PROUCT ESCRIPTION For concrete forming applications,the 2 /2" (62mm) forming pin is designed for fastening wood members up /2" in thickness. Each pin has a break off groove " from the point allow the wood forming members be easily removed. Fastener Accessories Catalog Shank Head Standard Standard Number Shank Length iameter iameter Box Carn Wt./00 50789 44mm - " 0.45" 0.205" 00,000.4 50790 62mm - 2 /2" 0.45" 0.205" 00,000.4 Fastener Accessories PROUCT ESCRIPTION In addition the assemblies, the following accessories are available for use with drive pins as indicated below. Fastener Accessories Catalog Standard Standard Number escription Box Carn 50400 Ceiling Clip (no pin) 9/32" and 5/6" holes 00,000 5042 7/8" Insulation Washer 00,000 Powers USA: (800) 524-3244 or (94) 235-6300 Canada: (905) 673-7295 or (54) 63-426 www.powers.com 26
P000 PROUCT INFORMATION P000 Powder-actuated Single Shot Tool TOOL ESCRIPTION The P000 is a Hammer actuated, do-it-yourself (IY) powder actuated ol. Engineered for high reliability, low maintenance and speed. This ol uses four levels of power: gray through yellow load (levels -4) and.300" Head rive Pins, 8mm Head Fasteners with lengths of /2" through 3" and /4"-20 studs. TECHNICAL ATA Tool Body Tool Length 3" Tool Weight Pin Length Precision Moulded Rubber and Precision Cast Aluminum 3 lbs /2" 3" Total Length Load Type.22 Caliber A Load Power Level Gray (), Brown (2), Green (3), Yellow (4) GENERAL APPLICATIONS AN USES Remodeling Electrical Fixtures Maintenance Applications Telecommunications P000 PINS Ballistic Point rive Pin.300"Head rive 8mm Head rive Pin /4"- 20 Threaded Stud PIN SIZE RANGE (TYP.) /2" 3" SUITABLE BASE MATERIALS Normal-Weight Concrete Concrete Masonry Steel ORERING INFORMATION Catalog Number escription Standard Box 5203 P000 Tool (Blister Pack) 20 Powers Fasteners, Inc. All Rights Reserved. For current information visit www.powers.com 27 www.powers.com Canada: (905) 673-7295 or (54) 63-426 Powers USA: (800) 524-3244 or (94) 235-6300
PROUCT INFORMATION P220 P220 Powder-actuated Single Shot Tool TOOL ESCRIPTION The P220 is a low velocity, single shot,.22 caliber ol which can be used install.300" head drive pins, 8mm head drive pins and /4"- 20 threaded studs, up 3" in tal length. The P220 is designed for maintenance or residential contracrs. TECHNICAL ATA Tool Body Engineered Plastic and Precision Cast Aluminum Tool Length 2 /2" Tool Weight 4.3 lbs Pin Length /2" 3" Total Length Load Type.22 Caliber "A" Load Power Level Gray (), Brown (2), Green (3), Yellow (4) GENERAL APPLICATIONS AN USES Conduit Clip Concrete Electrical Fixture Steel and Concrete Track Floor Wood Concrete Residential Construction Wood Steel P220 PINS Ballistic Point rive Pin.300" Head rive Pin 8mm Head rive Pin /4"- 20 Threaded Stud PIN SIZE RANGE (TYP.) /2" 3" SUITABLE BASE MATERIALS Normal-weight Concrete Concrete Masonry Steel ORERING INFORMATION Catalog Number escription Standard Box P220 Tool (eluxe Kit): Safety Glasses, isposable Ear Plugs Allen Wrenches, Wire Brushes, Tool Lubricant Spall Guard 52006 Pin Starter Kit:.300" Headed Pins: (50) /2", (50) ", (30) 3" with 7/8" washer Case 52007 P220 (Blister Pack) 52522 Pisn for the P220 5250 Nose Piece for the P220 5252 Pisn Reset Pin for the P220 20 Powers Fasteners, Inc. All Rights Reserved. For current information visit www.powers.com Powers USA: (800) 524-3244 or (94) 235-6300 Canada: (905) 673-7295 or (54) 63-426 www.powers.com 28
P35s PROUCT INFORMATION P35s Powder-actuated Load Strip Tool TOOL ESCRIPTION The P35s TM is specially designed for acoustical and drywall contracrs. It is a low velocity, semi-aumatic, ol which can be used install.300" head drive pins, 8mm head drive pins and /4"-20 threaded studs up /2" in tal length. The P35s TM is designed for high speed and repetitive volume applications. The standard version of the ol is supplied with a flat end pisn and a full size baseplate/guide. A limited access baseplate/guide assembly is also available. TECHNICAL ATA Tool Body Tool Length -/4" Tool Weight Pin Length Precision Cast Aluminum 4.25 /2" -/2" Total Length Load Type.25 Caliber 0 Load Strip Power Level Green (3), Yellow (4), Red (5) GENERAL APPLICATIONS AN USES Conduit Clip Concrete Electrical Fixture Steel Track Floor Wood Concrete Electrical Fixture Concrete Wood Steel Commercial Construction Reliable and Compact for Short Pin Applications P35s PINS Ballistic Point rive Pin.300" Head rive Pin 8mm Head rive Pin /4"- 20 Threaded Stud PIN SIZE RANGE (TYP.) /2" -/2" Total Length SUITABLE BASE MATERIALS Normal-weight Concrete Structural Lightweight Concrete Concrete Masonry Steel ORERING INFORMATION Catalog Number escription Standard Box 52002 P35s Tool (eluxe Kit): Safety Glasses, isposable Ear Plugs Allen Wrenches, Wire Brushes, Tool Lubricant Spall Guard Pin Starter Kit:.300 Headed Pins: (50) /2", (50) ", (00) -/4" Case 52023 P35s Tool (Blister pack) 52200 Pisn Standard 2/SF for the P35s 52204 Guide 2/F3- for the P35s 52206 Baseplate 2/S for the P35s Pole Tools for Overhead Attachments Catalog Number escription Standard Box 50065 6' i-electric Pole Tool 50066 8' i-electric Pole Tool 20 Powers Fasteners, Inc. All Rights Reserved. For current information visit www.powers.com 29 www.powers.com Canada: (905) 673-7295 or (54) 63-426 Powers USA: (800) 524-3244 or (94) 235-6300
PROUCT INFORMATION P720 P720 Powder-actuated Single Shot Tool TOOL ESCRIPTION The P720 is a low velocity, single shot.22 caliber ol which can be used install.300" head drive pins, 8mm head drive pins and /4"-20 threaded studs up /2" in tal length. The P720 is commonly used in the finishing trades. TECHNICAL ATA Tool Body Precision Cast Aluminum Tool Length 3-/2" Tool Weight 4.3 Pin Length /2" -/2" Total Length Load Type.22 Caliber "A" Load Power Level Gray (), Brown (2), Green (3), Yellow (4) GENERAL APPLICATIONS AN USES Conduit Clip Concrete Electrical Fixture Steel Track Floor Wood Concrete Electrical Fixture Concrete Wood Steel ORERING INFORMATION P720 PINS Ballistic Point rive Pin.300" Head rive Pin 8mm Head rive Pin /4"- 20 Threaded Stud PIN SIZE RANGE (TYP.) /2" -/2" Total Length SUITABLE BASE MATERIALS Normal-weight Concrete Structural Lightweight Concrete Concrete Masonry Steel Catalog Number escription Standard Box P720 Tool (eluxe Kit): Safety Glasses, isposable Ear Plugs Allen Wrenches, Wire Brushes, Tool Lubricant Spall Guard 52004 Pin Starter Kit:.300 Headed Pins: (50) /2", (50) ", (50) " Case 52005 P720 Tool (Blister pack) 52300 Pisn with Ring for the P720 52306 Nose Piece for the P720 52308 Pisn Reset Pin for the P720 Pole Tools for Overhead Attachments Catalog Number escription Standard Box 50060 6' i-electric Pole Tool 20 Powers Fasteners, Inc. All Rights Reserved. For current information visit www.powers.com Powers USA: (800) 524-3244 or (94) 235-6300 Canada: (905) 673-7295 or (54) 63-426 www.powers.com 30
P3500 PROUCT INFORMATION P3500 Powder-actuated Semi-aumatic Tool TOOL ESCRIPTION The P3500 is a low velocity, semi-aumatic.27 caliber ol which can be used install.300" head drive pins, 8mm head drive pins and /4"- 20 threaded studs, up 3" in tal length. The P3500 is designed for high speed, durability and repetitive volume applications. TECHNICAL ATA Tool Body Precision Cast Aluminum Tool Length 3-5/8" Tool Weight 5 Pin Length /2" 3" Total Length Load Type.27 Caliber 0 Load Strip and.27 Caliber Safety Strip Power Level Brown (2), Green (3), Yellow (4), Red (5) GENERAL APPLICATIONS AN USES Conduit Clip Concrete Electrical Fixture Steel Wood Concrete Concrete Forming Wood Steel Commercial and Residential Construction Electrical Fixture Concrete ORERING INFORMATION P3500 PINS Ballistic Point rive Pin.300" Head rive Pin 8mm Head rive Pin /4"- 20 Threaded Stud PIN SIZE RANGE (TYP.) /2" 3" Total Length SUITABLE BASE MATERIALS Normal-weight Concrete Structural Lightweight Concrete Concrete Masonry Steel Catalog Number escription Standard Box P3500 Tool (eluxe Kit): Safety Glasses, isposable Ear Plugs Allen Wrenches, Wire Brushes, Tool Lubricant Spall Guard, Spare Parts 52000 Pin Starter Kit:.300 Headed Pins: (50) /2", (50) ", (30) 3" with 7/8" washer Case 5200 P3500 Tool (Blister pack) 5206 Pisn Ring for the P3500 5208 Guide 2/F-3 for the P3500 520 Base Plate 2/S-3 for the P3500/PA3500 5220 Clip for the P35s/P3500/PA3500 522 Pisn Sp for the P3500/PA3500 5222 Steel Annular Ball for the P35s/P3500/PA3500 Pisn for Installing 8mm Head rive Pins Catalog Number escription Standard Box 5200 Pisn 2/N- (for 8mm Head rive Pins) for the P3500 Limited Access Baseplates Catalog Number escription Standard Box 524 Guide 2/F-4 Limited Access for the P3500 526 Baseplate 2/F-4- Limited Access for the P3500 Pole Tools for Overhead Attachments Catalog Number escription Standard Box 50065 6' i-electric Pole Tool 50066 8' i-electric Pole Tool 20 Powers Fasteners, Inc. All Rights Reserved. For current information visit www.powers.com 3 www.powers.com Canada: (905) 673-7295 or (54) 63-426 Powers USA: (800) 524-3244 or (94) 235-6300
PROUCT INFORMATION Powder Actuated PA3500 Powder-actuated Semi-aumatic Tool TOOL ESCRIPTION The PA3500 is a modified version of the P3500 that includes a power adjuster, allowing the operar effectively decrease the power level of the load being used by up two (2) levels. For example, a red load can be adjusted down the level of a green load. TECHNICAL ATA Tool Body Precision Cast Aluminum Tool Length 3-5/8" Tool Weight 5 Pin Length /2" 3" Total Length Load Type.27 Caliber 0 Load Strip and.27 Caliber Safety Strip Power Level Brown (2), Green (3), Yellow (4), Red (5) GENERAL APPLICATIONS AN USES Conduit Clip Concrete Electrical Fixture Steel Wood Concrete Concrete Forming Wood Steel Commercial and Residential Construction Electrical Fixture Concrete ORERING INFORMATION PA3500 PINS Ballistic Point rive Pin.300" Head rive Pin 8mm Head rive Pin /4"- 20 Threaded Stud PIN SIZE RANGE (TYP.) /2" 3" Total Length (Power adjuster must be set 6 for 3 pin fit in ol) SUITABLE BASE MATERIALS Normal-weight Concrete Structural Lightweight Concrete Concrete Masonry Steel Catalog Number escription Standard Box PA3500 Tool (eluxe Kit): Safety Glasses, isposable Ear Plugs Allen Wrenches, Wire Brushes, Tool Lubricant Spall Guard, Spare Parts 5209 Pin Starter Kit:.300 Headed Pins: (50) /2", (50) ", (30) 3" with 7/8" washer Case 52025 PA3500 Tool (Blister pack) 5203 PA Pisn Flat End with Ring for the PA3500 5208 Guide 2/F-3 for the P3500/PA3500 520 Base Plate 2/S-3 for the P3500/PA3500 522 Pisn Sp for the P3500/PA3500 5220 Clip for the P35s/P3500/PA3500 5222 Steel Annular Ball for the P35s/P3500/PA3500 Limited Access Baseplates Catalog Number escription Standard Box 524 Guide 2/F-4 Limited Access for the P3500/PA3500 526 Baseplate 2/F-4- Limited Access for the P3500/PA3500 Pole Tools for Overhead Attachments Catalog Number escription Standard Box 50065 6' i-electric Pole Tool 50066 8' i-electric Pole Tool 20 Powers Fasteners, Inc. All Rights Reserved. For current information visit www.powers.com Powers USA: (800) 524-3244 or (94) 235-6300 Canada: (905) 673-7295 or (54) 63-426 www.powers.com 32
P380 PROUCT INFORMATION P380 Powder-actuated Single Shot Tool TOOL ESCRIPTION Powerful and reliable heavy-duty powder actuated ol, for installing 3/8" threaded studs in concrete and steel. This ol features an easy load ejecr and has a low re-coil for greater operar comfort. The P380 is independent of any external power source saving you time and money. The ol can be converted shoot /4 threaded studs. TECHNICAL ATA Tool Body Precision Cast Aluminum Tool Length 4" Tool Weight 7 Pin Length /2" 3" Total Length Load Type.27 Caliber Single Short and Long Power Level Red (5), Purple (6) GENERAL APPLICATIONS AN USES Hanging Sprinkler Pipe Electrical Fixtures Hard Concrete Heavy-duty Applications for Steel and Concrete P380 PINS /4" and 3/8" Threaded Studs 3/8" Head rive Pins PIN SIZE RANGE (TYP.) /2" 3" Total Length SUITABLE BASE MATERIALS Normal-weight Concrete Structural Lightweight Concrete Steel ORERING INFORMATION Catalog Number escription Standard Box P380 Tool (eluxe Kit): Safety Glasses, isposable Ear Plugs Allen Wrenches, Wire Brushes, Tool Lubricant 52008 Spall Guard, Spare Parts Pin Starter Kit: Threaded studs: (00) /4", (50) 3/8" Case 20 Powers Fasteners, Inc. All Rights Reserved. For current information visit www.powers.com 33 www.powers.com Canada: (905) 673-7295 or (54) 63-426 Powers USA: (800) 524-3244 or (94) 235-6300
PROUCT INFORMATION P3600 P3600 Powder-actuated Semi-aumatic Tool TOOL ESCRIPTION The P3600 is a powerful, heavy-duty, low velocity, semi-aumatic.27 caliber ol, which can be used install 0mm head.77 diameter shank drive pins, 3/8"- 6 threaded studs, and 3/8" headed drive pins, The P3600 is designed for applications where more power is needed, such as attaching 2x4 hard aggregate or steel. The ol utilizes a red (5) or purple (6).27 caliber strip. TECHNICAL ATA Tool Body Tool Length 3-5/8" Tool Weight Pin Length Precision Cast Aluminum 5 lbs Up 3" Total Length Load Type.27 Caliber 0 Load Strip and.27 Caliber Safety Strip Power Level Red (5), Purple (6) GENERAL APPLICATIONS AN USES Ceiling Clip assemblies Electrical Fixtures Track Floor, oor Frames uct Straps Wood Concrete Concrete Forms, Basket Clips, Forming Pins P3600 PINS 0mm Head rive Pins 3/8 Threaded Studs 3/8 Headed rive Pins PIN SIZE RANGE (TYP.) /2" 3" Total Length SUITABLE BASE MATERIALS Normal-weight Concrete Structural Lightweight Concrete Concrete Masonry Steel ORERING INFORMATION Catalog Number escription Standard Box P3600 Tool (eluxe Kit): Safety Glasses, isposable Ear Plugs Allen Wrenches, Wire Brushes, Tool Lubricant Spall Guard 5200 Pin Starter Kit: 0mm Headed Pins: (5) ", (5) 5/8", (5) 2", (5) 2-/2 Case 52579 Guide for the P3600 522 Pisn sp for the P3600 52578 Pisn for the P3600 Pole Tools for Overhead Attachments Catalog Number escription Standard Box 50065 6' i-electric Pole Tool 50066 8' i-electric Pole Tool 20 Powers Fasteners, Inc. All Rights Reserved. For current information visit www.powers.com Powers USA: (800) 524-3244 or (94) 235-6300 Canada: (905) 673-7295 or (54) 63-426 www.powers.com 34
PA35 PROUCT INFORMATION PA35 Fully Aumatic Powder-actuated Tool TOOL ESCRIPTION The PA35 is a lightweight, fully aumatic, powder-actuated ol This ol can fasten several hundred nails per hour for increased productivity. A power adjuster provides variable load level choices and the ol aumatically cycles the load. TECHNICAL ATA Tool Body Composite Tool Length 7" Tool Weight 8 Pin Length 5/8" -5/8" Total Length Load Type.27 Caliber 0 Load Strip and.27 Caliber Safety Strip Power Level Brown (2), Green (3), Yellow (4), Red (5) GENERAL APPLICATIONS AN USES Electrical Fixtures Metal Track, oor Frames Conduit Clip Assemblies Concrete Forming uct Straps Commercial and Residential Construction Sill Plates/Wood Concrete Wood Steel PA35 PINS 8mm Head rive Pin PIN SIZE RANGE (TYP.) 5/8" -5/8" Total Length SUITABLE BASE MATERIALS Normal-weight Concrete Structural Lightweight Concrete Grouted Concrete Masonry Steel ORERING INFORMATION Catalog Number escription Standard Box PA35 Tool (eluxe Kit): Safety Glasses, isposable Ear Plugs 50275 Allen Wrenches, Wire Brushes, Tool Lubricant Spall Guard, Spare Parts Case 5233 PA35 Pisn with Ring 5235 Guide 2/F-3 for the PA35 5237 Base Plate 2/S-3 for the PA35 20 Powers Fasteners, Inc. All Rights Reserved. For current information visit www.powers.com 35 www.powers.com Canada: (905) 673-7295 or (54) 63-426 Powers USA: (800) 524-3244 or (94) 235-6300
PROUCT INFORMATION P60 P60 Powder Actuated Circular isc Magazine Tool TOOL ESCRIPTION The P60 is low velocity, circular disc.25 caliber magazine ol which can be used install.300 head drive pins, 8mm head drive pins and /4-20 threaded studs, up 3 in tal length. TECHNICAL ATA Tool Body Composite Tool Length 2-/4" Tool Weight 4.8 Pin Length /2" 2-3/8" Total Length Load Type.25 Caliber 0 Shot Circular isc Load Power Level Gray (), Brown (2), Green (4), Yellow (4) GENERAL APPLICATIONS AN USES Ceiling Clip Concrete Wood Concrete Wood Steel Electrical Fixtures Steel Electrical Fixtures Concrete P60 PINS 8mm Head rive Pin.300 Head rive Pin /4-20 Threaded Stud PIN SIZE RANGE (TYP.) /2" 2-3/8" Total Length SUITABLE BASE MATERIALS Normal-weight Concrete Structural Lightweight Concrete Grouted Concrete Masonry Steel ORERING INFORMATION Catalog Number escription Standard Box P60 Tool (eluxe Kit): Safety Glasses, isposable Ear Plugs Allen Wrenches, Wire Brushes, Tool Lubricant Spall Guard, Spare Parts 52057 Pin Starter Kit: 8mm Headed Pin 0 Fastener Magazine: (50) ", (50) ", (5) -/2" Case 20 Powers Fasteners, Inc. All Rights Reserved. For current information visit www.powers.com Powers USA: (800) 524-3244 or (94) 235-6300 Canada: (905) 673-7295 or (54) 63-426 www.powers.com 36
Powder Actuated Tools PROUCT INFORMATION Sniper Semi-Aumatic Pole Tool TOOL ESCRIPTION The Sniper Pole Tool is ideal for installing overhead ceiling clips with a -/2 pin. The ol features an internal safety sequence strip loading mechanism, allowing load advancements only after the pin has been installed in the nose piece, and handle must be clicked advance the next load. TECHNICAL ATA Tool Body Tool Length 7" Tool Weight Pin Length Composite 8 -/2" Total Length Load Type.27 Caliber in a ten strip load Power Level Brown (2), Green (3), Yellow (4), Red (5) GENERAL APPLICATIONS AN USES Ceiling Clip Assemblies Metal Track oor Frames Forming Applications Electrical Fixtures Steel Electrical Fixtures Concrete Sniper PINS.300 Head rive Pin 8mm Head rive Pin PIN SIZE RANGE (TYP.) /2" -/2" Total Length SUITABLE BASE MATERIALS Normal-weight Concrete Structural Lightweight Concrete Steel ORERING INFORMATION Catalog Number escription Standard Box 5205 Sniper Tool 52053 6 ft.pole 5206 8 ft. Pole 20 Powers Fasteners, Inc. All Rights Reserved. For current information visit www.powers.com 37 www.powers.com Canada: (905) 673-7295 or (54) 63-426 Powers USA: (800) 524-3244 or (94) 235-6300