Adhesive Dispensing Tools Our heavy-duty tools are designed to work with our for trouble-free dispensing. Each manual tool provides a 2: drive mechanism for easier dispensing of high-viscosity adhesive. Epoxy Adhesive Dispensing Tools CDT0S Manual Dispensing Tool for SET-XP 0 Adhesive and other Single Cartridge Adhesives The CDT0S features a steel carriage for ultimate durability and is engineered for continuous, high-volume use. The CDT0S also features double-gripping plates that help extend tool life. EDT22S Manual Dispensing Tool for 22 oz. Adhesive Cartridges The EDT22S epoxy adhesive tool features a steel carriage and is engineered for high-volume, continuous use. The tool can be easily convert from dispensing a 22 oz. : ratio cartridge to a. oz. 2: ratio cartridge. EDT22CKT Battery-Powered Dispensing Tool for 22 oz. Cartridges The EDT22CKT offers power dispensing without the need for a hose or compressor. The tool features dosage and rate control for maximum efficiency. Each battery charge dispenses approximately and recharging takes hour. Tool comes complete with two 4.4V batteries and a charger. EDTA22P Pneumatic Dispensing Tool for 22 oz. Cartridges The EDTA22P tool features an optional suitcase handle adapter for the ultimate in tool configuration and dispensing convenience. The suitcase option enables easier and time-saving ground-level doweling. The heavyduty tool comes with a custom, blow-molded plastic carrying case. EDTAP Pneumatic Dispensing Tool for oz. Cartridges The EDTAP tool features an optional suitcase handle adapter for the ultimate in tool configuration and dispensing convenience. The suitcase option enables easier and time-saving ground-level doweling. The heavyduty tool comes with a custom, blow-molded plastic carrying case. Premium tool for singletube Manual tool for 22 oz. Battery-powered tool for 22 oz. Pneumatic tool for 22 oz., 2 Pneumatic tool for oz., 2 CDT0S EDT22S EDT22CKT EDTA22P EDTAP. Air supply attachment is 4-8 NPT (male) thread. 2. Recommended operating air pressure is between 80 00 psi. CDT0S EDT22S EDT22CKT Tool and Charger EDTA22P C-SAS-202 202 Simpson Strong-Tie Company Inc. 2 Maintenance tips, troubleshooting and repair parts schematics available at www.strongtie.com. EDTAP
Acrylic Adhesive Dispensing Tools ADT8S Manual Dispensing Tool for 2. oz. Cartridges The ADT8S features a steel carriage for ultimate durability. The ADT8S also features double-gripping plates that help extend tool life. ADT0S Manual Dispensing Tool for 0 oz. Adhesive Cartridges The ADT0S features a steel carriage for ultimate durability and is engineered for continuous, high-volume use. The ADT0S also features double-gripping plates that help extend tool life. ADT0CKT Battery Powered Dispensing Tool for 0 oz. Cartridges The ADT0CKT offers power dispensing without the need for a hose or compressor. The tool features dosage and rate control for maximum efficiency. Each battery charge dispenses approximately and recharging takes hour. The tool comes complete with two 4.4V batteries and a charger. ADT8S ADT0S ADTA0P Pneumatic Dispensing Tool for 0 oz. Cartridges The ADTA0P tool features an optional suitcase handle adapter for flexible tool configuration and dispensing convenience. The suitcase option enables easier and time-saving ground-level doweling. The heavy-duty tool comes with a custom, blow-molded plastic carrying case. C-SAS-202 202 Simpson Strong-Tie Company Inc. Manual tool for 2. oz. Manual tool for 0 oz. Battery-powered tool for 0 oz. Pneumatic tool for 0 oz., 2 AD0CKT battery AD0CKT charger ADT8S ADT0S ADT0CKT ADTA0P EDT4B EDT4VCH. Air supply attachment is 4-8 NPT (male) thread. 2. Recommended operating air pressure is between 80 20 psi. ADT0CKT ADTA0P EDT4VCH Maintenance tips, troubleshooting and repair parts schematics available at www.strongtie.com.
Mixing Nozzles and Retaining Nuts Mixing nozzles are designed for the proper proportioning and mixing of the different adhesive formulations. Use only appropriate Simpson Strong-Tie mixing nozzle in accordance with Simpson Strong-Tie instructions. Modification or improper use of the mixing nozzle may impair epoxy or acrylic performance. EMN22i EMN22i An 8-element mixing nozzle for use with 22 oz. and oz. epoxy adhesives. This is a one-piece nozzle with integrated nut (separate retaining nut not required). AMNQ An -element, high-efficiency static mixing nozzle for use with all acrylic adhesive products. EMNA An 8-element, high-strength, mixing nozzle for dispensing epoxy adhesive through bulk metering equipment. Mixing nozzle for. oz. cartridge (separate retaining nut not required). 8-element nozzle for 22 oz. and epoxy adhesive. Features an integrated threaded nut for attachment to. Pkg EMN.-R 2 24 Packs (2 nozzles per pack) EMN22i 2 Nozzles Packs EMN22i-RP ( nozzles per pack) EMN22i-RP0 0 Packs (0 nozzles per pack) EMN22iB 00 EMNA 8-element nozzle for dispensing epoxy through metering equipment Hi-volume nozzle for 22 oz., and oz. (separate retaining nut not required), " long, major diameter " EMNA-RP Packs ( nozzles per pack) EMN0 0 AMNQ Five mixing nozzles for all AT products AMNQ-RP 0 Packs ( nozzles per pack) Adhesive Retaining Caps Adhesive retaining caps make overhead and horizontal installation easier by preventing the adhesive from running out of the hole. They also center the rod in the hole, making them ideal for applications where precise anchor placement is required. It may be necessary to provide support for the insert during cure time. Adhesive retaining caps are not designed to support the weight of the insert in overhead installations. MATERIAL: Plastic Epoxy Adhesive Retaining Caps For Rod Required Cap Depth Pkg * (ea) Adhesive Retaining Caps Acrylic Adhesive Retaining Caps For Rod Required Cap Depth Pkg * (ea) The X cut in the cap allows the mixing nozzle and insert to pass through, while containing the adhesive in the hole. C-SAS-202 202 Simpson Strong-Tie Company Inc. ARC-RP 200 ARCA-RP 200 ARC0-RP 200 ARC0A-RP 200 ARC2-RP 4 200 ARC2A-RP 200 ARC-RP 4 200 ARCA-RP 4 200 ARC8-RP 200 ARC8-RP 200 ARC00-RP 200 ARC00A-RP 200 ARC-RP 4 200 ARC-RP 4 200 *8 packages of. 4
Steel Adhesive-Anchoring Screen Tubes Screen tubes are used in hollow base material applications to contain adhesive around the anchor and prevent it from running into voids. Simpson Strong-Tie screen tubes are specifically designed to work with AT, SET and ET-HP adhesives in order to precisely control the amount of adhesive that passes through the mesh. This results in thorough coating and bonding of the rod to the screen tube and base material. Order screen tubes based upon rod diameter and adhesive type. The actual outside diameter of the screen tube is larger than the rod diameter. MATERIAL: Acrylic screen tubes: 0 mesh stainless steel; Epoxy screen tubes: 0 mesh carbon steel. Caution: Screen tubes are designed for a specific adhesive type. epoxy screen tubes must be used with SET or ET-HP formulations and acrylic screen tubes must be used with AT adhesive. Do not use SET.KTA with screen tubes. Epoxy Adhesive Screen Tube (Acrylic Screen Tubes Similar) Screen tubes are for use in hollow CMU, hollow brick and unreinforced masonry applications. Contact Simpson Strong-Tie for information on special order sizes. C-SAS-202 202 Simpson Strong-Tie Company Inc. Acrylic (AT) Screen Tubes Stainless Steel 4 Actual Screen O.D./Length. x ATS 0 x ATS 0 x ATS0 00 x ATS0 00 x 0 ATS00 0 x ATS2 0 x ATS2 0 x 0 ATS20 x ATS2 2 x 8 ATS8 2 x ATS 2 x ATS Epoxy (SET & ET-HP) Screen Tubes Carbon Steel 4 Note: Not for use with SET.KTA. Actual Screen O.D./Length. x ETS 0 x 0 ETS0 00 x ETS0 00 x 0 ETS00 0 x ETS2 0 x 0 ETS20 x ETS2 2 x 8 ETS8 2 x ETS 2 x ETS 2 x 2 ETS2
Opti-Mesh Adhesive-Anchoring Screen Tubes Screen tubes are vital to the performance of adhesive anchors in base materials that are hollow or contain voids, such as hollow block and brick. The Simpson Strong-Tie Opti-Mesh screen tube provides the economical advantage of a plastic screen tube while providing performance comparable to steel screen tubes and better than competitive plastic screen tubes. MATERIAL: Plastic Caution: Screen tubes are designed for a specific adhesive type. Epoxy screen tubes must be used with SET or ET-HP formulations and acrylic screen tubes must be used with AT adhesive. Do not use SET.KTA with screen tubes. Epoxy (SET and ET-HP) Screen Tubes - Plastic ³ ₈ ¹ ₂ ⁵ ₈ Acrylic Screen Tubes - Plastic ⁹ ₁₆ ³ ₄ ⁷ ₈ ³ ₄ Length ¹ ₂ 0 ¹ ₂ 0 ¹ ₂ 0 8 2 Length ETSP ETSP ETS0P ETS0P ETS0P ETS00P ETS2P ETS2P ETS20P ETS2P ETS8P ETSP ETSP ETS2P. 0 0 00 00 00 0 0 0 Load values for installations with SET are on page 0. Load values for installations with ET-HP in unreinforced masonry are on page 44. Not for use with SET.KTA.. ³ ₈ ⁹ ₁₆ ¹ ₂ ATSP ATSP 0 0 ¹ ₂ ³ ₄ 0 ¹ ₂ 0 ¹ ₂ ATS0P ATS0P ATS0P ATS00P ATS2P 00 00 00 0 0 ⁵ ₈ ⁷ ₈ ATS2P 0 0 ATS20P 8 ATS2P ATS8P ³ ₄ ATSP ATSP 2 ATS2P Load values for installations with AT adhesive are on page. Integral Cap: Serves to center and secure the rod in the screen tube, while displaying important information such as rod diameter, drill bit diameter and the Simpson Strong-Tie " " sign for easy inspection after installation. The cap also prevents adhesive from running out of the front of the screen tube. Flanges: Prevents the screen tube from slipping into over-drilled holes. Allows screen tube to function in holes that are drilled too deep. Open-Mesh Collar: This section of larger mesh allows extra adhesive to flow out of the screen tube behind the face shell of hollow block applications. The extra "collar" of adhesive increases bearing area and results in higher load capacities in hollow concrete block. Color-Coded, Formula-Specific Mesh: The screen tube mesh is sized to allow only the right amount of adhesive to flow through the screen tube to bond with the base material while the balance remains in the screen to bond the rod. The acrylic screen tube mesh is white while the expoxy screen tube mesh is black. U.S. Patent,8,08 Epoxy Screen Tube (mesh is black) Screen tubes are for use in hollow CMU, hollow brick and unreinforced masonry applications. The integral cap centers the rod and displays drill bit and rod diameter. Acrylic Screen Tube (mesh is white) The photo on the left shows the Opti-Mesh screen tube installed in a hollow CMU block. The extra collar of adhesive created by the open-mesh collar results in increased bearing area and higher load values. The typical screen tube shown on the right relies on the bond between the relatively small amount of adhesive in contact with the face shell of the block for its holding power. C-SAS-202 202 Simpson Strong-Tie Company Inc.
Cleaning Brushes Brushes are used for cleaning drilled holes prior to adhesive anchor installation. Brushes have a twisted wire handle with nylon bristles. For Anchor/Rebar For ½" dia x " brush (8" total length) ETB4 4" " " " 24 ETB 4" x 4" brush (" total length) ETB " " " 4" 24 " x 4" brush (" total length) " x 4" brush (24" total length) 4" x 4" brush (2" total length) " x " brush (4" total length ETB8 4" " " 24 ETB8L 4" " " 24 ETB0 " " " " 24 ETB2 4" " " 24 Adhesive Shear Tubes Used in conjunction with anchoring adhesive and screen tubes, adhesive shear tubes transfer anchor shear loads over a larger area, reducing localized crushing in unreinforced masonry installations. Required for thru bolt applications per ICC-ES's unreinforced masonry anchorage "Configuration C" detail. For detailed installation instructions refer to the appropriate adhesive anchor ICC-ES report. Adhesive Shear Tube MATERIAL: Steel FINISH: Zinc-plated "x"x " STEEL PLATE WIRE MESH SCREEN TUBE STEEL SLEEVE (SHEAR TUBE) For use with Simpson Screen Drill Bit Threaded Rod. HEX NUT " DIA. THREADED ROD x 8 AST800 ETS8, ATS8 C-SAS-202 202 Simpson Strong-Tie Company Inc.. Screens sold separately. Not for use with Simpson Strong-Tie screen #ETS8P or ATS8P plastic Opti-Mesh screen tubes. Retrofit Bolts RFBs are pre-cut threaded rod, supplied with nut and washer. For use with Simpson Strong-Tie adhesives. May be ordered in bulk without the nut and washer. Use with Simpson Strong-Tie adhesives to anchor into existing concrete and masonry. Offers a complete engineered anchoring system when used with Simpson Strong-Tie anchoring adhesives. Each end of the threaded rod is stamped with rod length in inches and our No-Equal symbol for easy identification after installation. MATERIAL: ASTM F4 Grade FINISH: Zinc-plated, hot-dip galvanized Length Zinc Plated Hot-Dip Galvanized Bulk Retail 2 Pack " x 4" RFB#4x4 RFB#4x4HDG 0 0 Configuration C RFB Retrofit Bolts " x " RFB#4x RFB#4xHDG 0 0 0 " x " RFB#4x RFB#4xHDG 0 0 0 " x " RFB#4x RFB#4xHDG 0 0 0 " x 8" RFB#4x8HDG 0 " x 0" RFB#4x0 RFB#4x0HDG 0 " x " RFB#x RFB#xHDG 0 0 0 " x 8" RFB#x8 RFB#x8HDG 0 0 " x 0" RFB#x0 RFB#x0HDG 0 0 " x 2" RFB#x2HDG 0 " x " RFB#x RFB#xHDG 0 4" x 0 " RFB#x0. RFB#x0.HDG. Bulk quantities do not include the nut and washer and must be ordered with a -B suffix (example: RFB#4x-B). Hot-dip galvanized RFB s not available in bulk. 2. Retail packs must be ordered with a -R suffix (example: RFB#x2HDG-R).