MICROOPTO Overview Short-circuit-proof switching amplifier for inductive loads up to 10 Powerful, compact solid-state relay with error signalling contact The MICROOPTO family offers the customer high-quality optos and solid-state relays for application-oriented problem solutions. ll products are designed in the space-saving 6 terminal size. The new solid-state relay can be connected in the output circuits of control systems and feedback control modules for selective activation of inductive loads up to 4 V DC / 10, such as solenoid valves, contactors etc. The error controlled output monitors short-circuts and, if necessary, switched off; a potential-free signalling contact provides feedback to the control system the system can be shut down in a controlled manner for error rectification. The powerful output of the MICROOPTO SOLENOID switches 10 at 55 C. The product can be used worldwide thanks to international approvals: CE, culus and GL. larm function Clear condition display through status and error LEDs in the output. Space-saving Space-saving 6 modular width..5 147050000 013/014
MICROOPTO Overview Not sensitive Protected by suppressor circuit on input and output circuits. Tough and sturdy With a short-circuit-proof output. uxiliary contact n auxiliary contact issues alerts in event of short circuits. 147050000 013/014.53
For switching valves up to 4 V DC 10 Width only 6 Plug-in cross-connector For mounting on TS 35 Status display and error signaling contact with an error in the output 4 V DC / 5-33 V DC 10 13 The MICROOPTO SOLENOID solid-state relay is used specifically as a switching amplifier for actuators up to 4 V DC and 10 with inductive loads such as solenoid valves and contactors. potential-free signalling contact transmits errors, such as short circuits, to the controller. The MICROOPTO SOLENOID solid-state relay is short-circuit-proof and protected against power-related transients and voltage peaks by extensive protective circuits. The closed housing also offers a high level of protection against contact. 1 14 1 MICROOPTO 10 10 4 3 4 V DC ±0 % 400 mw > 18 V < 13 V 50 Hz Error LED red; Status LED green POWER MOS-FET 5...33 V DC 10 approx. 100 mv < 1 m Resistance / Current sensor, Varistor, integrated free-wheel diode Load current [] 8 6 4 0 0 10 0 30 40 50 60 70 80 90 mbient temperature [ C] Switching frequency 50 Hz Switching frequency 1 Hz e.g. pneumatic valve bar Valve larm contact mbient temperature (operational) pprovals typical. 50 µs / typical. 700 µs LC 5...48 V DC / 0.1-5 C...+60 C -40 C...+60 C 40 C / 93 % rel. humidity, no condensation CE; culus; GL; GOSTME5 30 4 kv (1./50 µs) > 3 III Power supply 4 1 13 ERROR 10 14 3.5 / 0.5 / 4 Suppressor circuitry for inductive loads, 10 cm installation clearance to inductive switching devices. MOS 4VDC/5-33VDC 10 1 8937940000 uxiliary contact for error messages ccessories ccessories and dimensioned drawings: refer to the MICROOPTO ccessories.54 147050000 013/014
For DC loads up to 30 DC and 1 Only 6 modular width Plug-in cross-connection Power Boost: 0 / 0 ms, 5 / 1 sec 1...30 DC 1 4 V DC ±0 % 0.36 W > 18.8 V < 14.7 V 50...60 Hz Green LED POWER MOS-FET 1...30 DC 1 0.4 V < 1 µ No / Varistor, integrated free-wheel diode larm contact mbient temperature (operational) pprovals < 18 µs / < 1 ms 7 (10 ms) LC -0 C... C -40 C...+80 C 5 95% rel. humidity, T u = 55 C, no condensation CE; culus; GL; GOSTME5 30.5 kv (1./50 µs) > 3 II.5 / 0.5 / 4 MOS 4VDC/1-300VDC 1 1 8937830000 ccessories ccessories and dimensioned drawings: refer to the MICROOPTO ccessories 147050000 013/014.55
For direct connection of actuators up to 4 V DC, Only 6 modular width Plug-in cross-connection PE connection direct to mounting rail Status display when error in output 8...3 DC The solid-state relay MICROOPTO CTOR has been specifically designed as a switching amplifier for actuators up to 4 V DC and with inductive loads such as solenoid valves and contactors. 3-wire actuators can be connected directly to the module. This is short-circuit proof and protected against application-related transients and spikes by extensive protective circuitry. +4 V DC 6 5 MICROOPTO 4 V DC ±0 % 170 mw > 13.8 V < 13.6 V 15 Hz Error indication LED red; status LED green Intelligent POWER MOS-FET 8...3 DC 50 mv < 10 µ Yes (thermal cut-out) / Varistor, integrated free-wheel diode Load current [] 4 3 1 0 0 10 0 30 40 50 60 70 80 90 mbient temperature [ C] Switching frequency 100 Hz Switching frequency 1 Hz Example: pneumatic valve bar Valve PE larm contact mbient temperature (operational) pprovals 0.1 ms / < 0.5 ms LC -0 C... C -40 C...+80 C 5 95% rel. humidity, T u = 55 C, no condensation CE; culus; GL; GOSTME5 3 50 (1,/50 µ) 35 eff / 1 min. 35 eff / 1 min. II.5 / 0.5 / 4 1 +4 V DC Power supply 100 C ERROR 14 TS 35 PE PE MOS 4VDC/8-30VDC 1 8937970000 PE ccessories ccessories and dimensioned drawings: refer to the MICROOPTO ccessories.56 147050000 013/014
For direct connection of actuators up to 4 V DC Width only 6 Plug-in cross-connector Status display when error in output 4 V DC / 8-3 DC E The solid-state relay MICROOPTO CTOR has been specifically designed as a switching amplifier for actuators up to 4 V DC and with inductive loads such as solenoid valves and contactors. 3-wire actuators can be connected directly to the module. This is short-circuit proof and protected against application-related transients and spikes by extensive protective circuitry. +4 V DC 4 V DC ±0 % 170 mw > 13.8 V < 13.6 V < 10 Hz Error indication LED red; status LED green Intelligent POWER MOS-FET 8...3 DC 50 mv < 10 µ Yes (thermal cut-out) / Varistor, integrated free-wheel diode Example: pneumatic valve bar Valve larm contact mbient temperature (operational) pprovals 0.1 ms / < 0.5 ms LC -0 C...+60 C -40 C...+80 C 5 95% rel. humidity, T u = 55 C, no condensation 3 50 (1,/50 µ) 35 eff / 1 min. 35 eff / 1 min. II.5 / 0.5 / 4 1 +4Vdc Power supply 100 C ERROR 0V 14 MOS 4VDC/8-30VDC E 10 18330000 PE ccessories ccessories and dimensional drawings: refer to the MICROOPTO ccessories page 147050000 013/014.57
For electronically switching or inverting signals 4 V DC / 5-48 V DC 0.5 4 V DC ±0 % 160 mw > 18.8 V 1 khz Green status LED Transistor 5...48 V DC 500 m Max. 1 V < 1.5 m No / Integrated free-wheel diode larm contact mbient temperature (operational) pprovals < 30 µs / < 50 µs LC -5 C...+60 C -40 C...+60 C 40 C / 93 % rel. humidity, no condensation CE; culus; GL; GOSTME5 30 4 kv (1./50 µs) > 3 III.5 / 0.5 / 4 MOS 4VDC/5-48VDC 0,5 1 8937980000 ccessories ccessories and dimensioned drawings: refer to the MICROOPTO ccessories.58 147050000 013/014
For high switching frequency up to 100kHz Width only 6 Plug-in cross-connector For mounting on TS 35 1...8 V DC 100 khz +4 V DC special interior circuit in the opto module MICROOPTO 100 khz ensures that rapidly transmitted signals are isolated from one another and that they can be transferred practically without delay. This allows switching frequencies up to 100 khz to be achieved. Comprehensive suppressor circuits safeguard the module against conducted transients and voltage spikes. Max. switching frequency is dependent on the duty cycle deviation MOS 1-8 V DC 100 khz (switching current 50 m, ohmic load) 600 1 V DC...8 V DC 80 mw > 5.6 V 15 V DC 100 khz Green LED Transistor 19.6...8.8 V max. 50 m V < 1 µ No / Max. switching frequency [khz] 500 400 300 00 100 0 0 4 6 8 10 1 14 16 18 0 Duty-cycle deviation [%] For example rotational speed measurement Sensor larm contact mbient temperature (operational) pprovals < 00 ns / < 400 ns 0.6 (0 ms) LC -0 C...+60 C -40 C...+80 C 5 95% rel. humidity, T u = 55 C, no condensation CE; culus; GL; GOSTME5 3 50 (1,/50 µ) 35 eff / 1 min. 35 eff / 1 min. II Power supply +4 V DC.5 / 0.5 / 4 MOS 1-8VDC 100kHz 1 8937990000 ccessories ccessories and dimensioned drawings: refer to the MICROOPTO ccessories 147050000 013/014.59
For adjusting TTL signals 5 V TTL / 4 V DC 0.1 To adjust sensitive TTL signals to the typical voltage level of 4 V DC used in industrial automation applications, the MICROOPTO TTL modules are used. For the protection of the electronics, the sensitive TTL signals require electrical isolation from the 4 V world. To control the optical coupler circuit via the 5 V TTL signal, an additional auxiliary voltage is fed in. +4 V DC TTL 14 +5 V DC 5 V TTL < 0.5 mw approx. V ca. 1 V 100 khz Green status LED TTL 4 VDC ±0% 100 m < 1 V < 0 µ No / Integrated free-wheel diode e.g. printer interface TTL larm contact mbient temperature (operational) pprovals < 1.3 µ / < 1 µs LC -5 C...+60 C -40 C...+60 C 40 C / 93 % rel. humidity, no condensation CE; culus; GOSTME5 30 4 kv (1./50 µs) > 3 III +5 V DC +4 V DC TTL 14 TTL 4 V DC +5 V DC.5 / 0.5 / 4 MOS 5VTTL/4VDC 0,1 1 893790000 1 SVTTL 1-8 V DC TTL ccessories ccessories and dimensioned drawings: refer to the MICROOPTO ccessories.60 147050000 013/014
For adjusting TTL signals 1-8 V DC / 5 V TTL To adjust sensitive TTL signals to the typical voltage level of 4 V DC used in industrial automation applications, the MICROOPTO TTL modules are used. For the protection of the electronics, the sensitive TTL signals require electrical isolation from the 4 V world. To control the optical coupler circuit via the 5 V TTL signal, an additional auxiliary voltage is fed in. +5 V 1 OUT 5 VTTL 1 V DC...8 V DC 150 mw > 10.7 V < 10.6 V 100 khz Green status LED TTL 5 V TTL max. 50 m 90 mv < 1 µ No / Varistor e.g. printer interface TTL larm contact mbient temperature (operational) pprovals typical. < 1 µs / typical. < 4 µs LC -5 C...+60 C -40 C...+60 C 40 C / 93 % rel. humidity, no condensation CE; culus; GOSTME5 30 4 kv (1./50 µs) > 3 III +5 V DC +4 V DC TTL 14 TTL 4 V DC +5 V DC.5 / 0.5 / 4 MOS 1-8VDC/5VTTL 1 8937930000 1 SVTTL 1-8 V DC TTL ccessories ccessories and dimensioned drawings: refer to the MICROOPTO ccessories 147050000 013/014.61
MICROOPTO ccessories ccessories MICROOPTO Plug-in cross-connection Type No. of poles Qty. Order No. yellow ZQV 4N / GE 60 175850000 ZQV 4N / 3 GE 3 60 176630000 ZQV 4N / 4 GE 4 60 17660000 ZQV 4N / 10 GE 10 0 175860000 ZQV 4N / 0 GE 0 0 190900000 red ZQV 4N / RT 60 1793950000 ZQV 4N / 3 RT 3 60 1793980000 ZQV 4N / 4 RT 4 60 1794010000 ZQV 4N / 10 RT 10 0 1794040000 ZQV 4N / 0 RT 0 0 1909150000 blue ZQV 4N / BL 60 1793960000 ZQV 4N / 3 BL 3 60 1793990000 ZQV 4N / 4 BL 4 60 179400000 ZQV 4N / 10 BL 10 0 1794050000 ZQV 4N / 0 BL 0 0 1909100000 black ZQV 4N / SW 60 1793970000 ZQV 4N / 3 SW 3 60 1794000000 ZQV 4N / 4 SW 4 60 1794030000 ZQV 4N / 10 SW 10 0 1794060000 ZQV 4N / 0 SW 0 0 190910000 Screw- Conductor connection Solid H07V-U 0.5 4.0 Stranded H07V-K 0.5.5 f with wire end ferrules to DIN 468-1 0.5 1.5 f with wire end ferrules with plastic collar 0.5 1.5 Max. clamping range 0.13 4.0 Plug gauge to IEC 60947-1 Size 3 General technical data Nominal torque Nm 0.6 for -pole cross-connection 10 for multi-pole cross-connection 10 Stripping length 7 Ingress protection class IP 0 Housing material Wemid Nominal current 6 Nominal voltage V 50 Other accessories Supply terminals MOS SUPPLY 1 8973460000 MOS FEED THROUGH 1 8973450000 Markers WS 1/6 1 x 6 600 1609900000 Labels, Lasermark LM MT 300 15/6 ge 484 labels / sheet 10 1686360000 Screwdriver SD 0.6 x 3.5 x 100 10 9008330000 Cross-connector for plugging into the clamping point QB 75/6./15 10 053500000 Coloured insulating profile for QB ISPF QB75 black 10 056700000 ISPF QB75 blue 10 056780000 ISPF QB75 red 10 056760000 End bracket WEW 35/ 100 106110000 Drawings: Supply terminals 8973460000 MOS SUPPLY 8973450000 MOS FEED THROUGH 3 5 1 6 3 4 4 97.8 88 90 5 1 6 6.1.6 147050000 013/014