KEY FEATURES Temperature Stability +/-5ppm 100 V to 800 V into 50 Ω <15 ns leading edge 20 ns to 20 µs Pulse width Positive or negative pulse Adjustable rates up to 40 KHz 1ns resolution delay and Width control Double pulse mode Parameters may be controlled via front panel, GPIB and RS-232 APPLICATIONS High Voltage Test Photo Detector Photo Multiplier ATE (Automated Test Equipment) DESCRIPTION The model 6040 consist of programmable pulse & digital delay generator mainframe and a family of optional plug-in modules. The mainframe provides 0.01% timing accuracy with up to 100MHz repetition rate, 1ns step delay and pulse width resolution. The triggering jitter of 25 ps provides synchronizing capabilities usually associated with only best delay generators. The mainframe without any module provides capable positive and negative outputs. Interchangeable Plug-in modules let you select the output configuration you currently need. Capabilities of the mainframe with its module include: single pulse, double pulse, impulse, external drive, external modulation and CW. The modules themselves determine which of these capabilities are available. Modules: These interchangeable modules provides electrical signals from 5V, 180 ps rise time to 800 V, 10 ns rise time. The modules offer rep rate, and width and amplitude control. The following chart presents the Electrical Module Models. The detailed characteristics of every module are presented in the following pages. Model 310H 202H 201E Characteristics Offset Max Rate Rise Min Max Into 50 Ω time Width Width Higher Pulse 100 V to 800 V None 40 KHz 10 ns 25 ns 20 µs 1%/µs droop High Pulse 50 V to 300 V None 500 KHz 5 ns 12 ns 5 ms.005%/µs droop Fast Rise time 1 V to 5 V ± 5 V 100 MHz 180 ps 3 ns 640 seconds High rep Rate August 2017 www.bncfrance.com Page 1
MAINFRAME SPECIFICATIONS Listed below are the timing and output characteristics of the 6040 mainframe. However, modules determine specific performance limits and characteristics such as maximum pulse width and maximum rep rate. Internal Pulse Width Trig Out ECL Out External Single Cycle Double Pulse Impulse External Drive External Modulation CW Programming Dimension Weight Modules Characteristics 0.01Hz to 100 MHz, Accuracy: 0.01% of setting 3 ns to 640 S, resolution of 1 ns or 5 digits, accuracy 0.2%, jitter 25 ps or 0.005% 0 ns to 640 S, resolution of 1 ns or 5 digits, accuracy 0.2%, jitter 25 ps or 0.005% A 3 ns wide, 2V high T0 pulse into 50 ohms A positive 4V pulse into 50 ohms. 1 ns rise time An ECL level output into 50 ohms. 700 ps rise time 0 to 100 MHz, slope select and threshold adjust, 50 ohm input impedance A push button initiates a single pulse cycle A pair of identical width pulses separated by the delay for each event A sub-ns impulse is provided for each event. (optical only) An incoming waveform drives a module s output between two selected levels. Analog or digital signals modulate the output of an optical module with high bandwidths. (Optical only) Constant light level outputs. (optical only) GPIB, RS232, Local from pushbutton and LCD display 324mm W X 133 mm H x 406 mm D 7.3 kg 115/230 V, 50/60 Hz, 80 W Permanent memory: A ROM in the module determines the instrument s allowable operating condition. Store: 10 complete instrument settings can be stored. Module can be removed without loss of these settings. Recall: Stored settings can be manually recalled or bus transferred to the mainframe. Dimensions: 95 mm X 124 mm X 254 mm August 2017 www.bncfrance.com Page 2
310 H- FAST 800 V ELECTRICAL PULSE MODULE Model 310H adapts the Mainframe 6040 to amplitude requirements of up to 800V for 50 ohm loads. The operating capabilities of the 6040/310H provide outputs in the form of 1 ns resolution digital delays and gates and PRFs from.01 Hz to 100 khz (or one shots), in both single and double pulse formats. Leading edge transitions are 10 ns or less and trailing edges as low as 10 ns. Polarity is switch selectable and pulse width can range from a minimum of 25 ns up to 20 us. The 6040/310H combination retains the high timing accuracy, low jitter, nanosecond resolution, memory storage and programmability available with other installed 6040 modules. Also, the 310H self-protects against damage from operation at excessive duty factors or into a short circuit, with a light signaling overload conditions. Refer to the eight-page Model 6040 product bulletin or at this site for additional detailed information on equipment operation, a timing diagram and applications. Resolution Linearity +/- 1%. Transition Times (10% to 90%) Max. Max. Current Droop Aberrations 100 V to 800 V into 50 ohms. Fixed 0 V baseline. Polarity internally switch selectable. 5 V (to max. amplitude). Leading edge: < 10 ns. Trailing edge: between 200 V and 750 V, 10 ns. Other amplitudes, 15 ns max. 16.2 W average, 16.2 kw peak (at 800 V). 18 A peak. 1%/~s max. Connector Type N. +/- 10% of amplitude. Internal 0.01 Hz to 40 khz at 800 V. to 50 khz at 800 V, to 100 khz at 600V or less; external 0 Hz to same maximums as above. 25 ns to 20 us (see Droop). Calibrated at 500 V; at other amplitudes true witdhs vary slightly in fixed value up to 10 ns max. Duty Factor 0.1% max. at 800 V. Duty factors increase up to 9% at 100 V. 0 ns to 640 s (plus fixed delay). 500 ns (trailing to leading edges). 30 ns typical (fixed) mainframe's to module's. Jitter Module 50 ps RMS. Accessories Coaxial 50-Ohm Load Resistor Part Number 6860 Rated for 100 W continuous and 20 kw peak (800 V <20 us pulses). For terminating the 310H into high impedance loads or substitute for inadequate average or peak power-dissipating 50 ohm terminations. 7"L x 2 3/4" Sq (178 x 70 mm). August 2017 www.bncfrance.com Page 3
202 H- 300 V ELECTRICAL PULSE MODULE Fast High Voltage Pulses with and Width Control The Model 202H is a high-voltage (300V) plug-in module for BNC Model 6040 Mainframe. It offers nanosecond rise times and very low jitter. The sharp edges of the 202H are ideal for testing components, gating flash-lamps, triggering capacitor banks, or other experiments requiring high voltage pulses. The voltage is terminated into 50 Ohms. The pulse amplitude and width are adjustable via the front panel or remote programming. The Model 202H may be triggered with an internal rate generator, external trigger or external modulation. There is an ECL output, a from BNC Model 6040 Mainframe, and a High Voltage from the 202H module (BNC connector). Resolution Linearity +/- 1%. Transition Times (10% to 90%) Max. Max. Current Droop Aberrations Settling Time 20 V to 300 V into 50 ohms. Fixed 0 V baseline. Polarity internally switch selectable. 2 V (to max. amplitude). Leading edge: 3nS typical (5 ns max); Trailing edge 1O ns typical (longer with lower amplitude) 18 W average, 1.8 kw peak (at 300 V). 6 A peak. 0.005% us max. +/- 5% of amplitude (2% typical). 5 ns. Internal 0.01 Hz to 500 khz; external 0 to 500 khz. Rates to 1 MHz at lower amplitudes. 12 ns to 5mS (see Droop). Calibrated at 300 V; at lower amplitudes true witdhs increase slightly in fixed value up to 10 ns max. Duty Factor 1% max. at 300 V. Duty factors increase up to 25% at 20 V. Module 0 ns to 640seconds (plus fixed delay). 200 ns (trailing to leading edges). 55 ns typical (fixed) mainframe's to module's. Jitter 25 ps RMS. August 2017 www.bncfrance.com Page 4
201 E- 150 PS RISE TIME PULSE MODULE Fast Pulses with and Width Control The Model 201E is a plug-in module for BNC Model 6040 Mainframe. It offers 150pS rise times and very low jitter. The sharp edges of the 201E are ideal for testing components or triggering experiments. The pulse amplitude and width are adjustable via the front panel or remote programming. The 201E may be triggered with an internal rate generator, external trigger or external modulation. There is an ECL output, a from the 6040, and a Fast from the 201E module (SMA connector). Offset Rise Time 1 V to 5V into 50 Ω +/- 5 V 150 ps Internal 0.01 Hz to 100 MHz; external 0 to 100 MHz. 3 ns to 640 seconds. 1 ns available through internal adjustment or with External Drive (contact factory). Duty Factor 1% max. at 300 V. Duty factors increase up to 25% at 20 V. Module 0 ns to 640seconds (plus fixed delay). 200 ns (trailing to leading edges). 55 ns typical (fixed) mainframe's to module's. Jitter 25 ps RMS. ORDERING INFORMATION Model Model 310H Model 202H Model 210E Description Mainframe + 310H- Fast 800 V Pulse module 202H- 300V Electrical Pulse module 210E- 150 ps Rise Time module August 2017 www.bncfrance.com Page 5