NOTE: CONTACT VEEM IF GYRO UNIT INTENDED TO BE LOCATED MORE THAN m ABOVE DWL OR MORE THEN 70% OF LWL FORWARD OF TRANSOM. GYRO UNIT MAY BE INSTALLED WITH FRONT PANEL FACING FORWARD OR AFT. FRONT PANEL MUST NOT BE ALIGNED ATHWARTSHIPS. 8.5 070 80.3 040 REAR PANEL SIDE 8.7 00 LEFT PANEL SIDE RIGHT PANEL SIDE FORE OR AFT ISOMETRIC VIEW FRONT PANEL SIDE TOP VIEW UPDATED MODEL MT MA PS. DESCRIPTION DRN INITL DATE ENG CHK INITL DATE ISIONS MAN APP INITL DATE CAST APP INITL DATE MACH APP INITL DATE 3. COPYRIGHT 05 ALL RIGHTS RESERVED BY VEEM LTD. THIS DRAWING HAS BEEN ANY MANNER WITHOUT PRIOR WRITTEN APPROVAL OF VEEM LTD www.veem.com.au TEL: +6 8 9455 9355 FAX: +6 8 9455 9333 INSTALLATION DRAWING 060DT000.0 0 OF 0 :5
NOTE: 4 x M30 COLLARED EYEBOLTS TO BE USED FOR LIFTING. COLLARED EYEBOLTS MIN WLL 4.00t EACH, (AS 37 OR EQUIVALENT) MAXIMUM SLING ANGLE 60. SPREADER BAR 780mm LONG TO BE USED 780mm SPREADER BAR 70 MINIMUM 60 MAX 70 MINIMUM 70. 780 REAR PANEL SIDE 4 x LIFTING POINTS FOR INSTALLATION SEE NOTE 6.8 68 SIDE VIEW LEFT PANEL SIDE RIGHT PANEL SIDE 8.3 70 7.5 699 FORE OR AFT ISOMETRIC VIEW REMOVE TOP PANELS FRONT PANEL SIDE TOP VIEW REMOVE TOP PANELS COPYRIGHT 04 05 ALL RIGHTS RESERVED BY VEEM LTD. THIS DRAWING HAS BEEN ANY MANNER WITHOUT PRIOR WRITTEN APPROVAL OF VEEM LTD www.veem.com.au TEL: +6 8 9455 9355 FAX: +6 8 9455 9333 DRAFTING TO DESCRIPTION 3. 0 OF 0 :5 LIFTING INSTALLATION DRAWING 060DT000.0
.88 37 57.8 468 47.05 95 4.7 0 FRONT PANEL VIEW SEA WATER OUT FEMALE BSPP " SEA WATER IN FEMALE BSPP " 60L/MIN REAR PANEL VIEW POWER SUPPLY AC: 380/480V, 50/60Hz, 80A DC: 4V DC, 50A ELECTRICAL & DATA CABLES TERMINATED THROUGH GLANDS IN CABINET SEA WATER TEMP [ C] REQUIRED FLOW [L/min] SEAWATER EXIT TEMP [ C] 35 60 65 30 47 65 5 40 65 0 35 65 COPYRIGHT 04 ALL RIGHTS RESERVED BY VEEM LTD. THIS DRAWING HAS BEEN ANY MANNER WITHOUT PRIOR WRITTEN APPROVAL OF VEEM LTD www.veem.com.au TEL: +6 894559355 FAX: +6 894559333 3. EXTERNAL CONNECTIONS 060DT000.03 03 OF 0 :5
NOTE: THIS MODEL REPRESENTS THE ACTUAL SIZE ENVELOPE OF THE GYRO STABILISER A MINIMUM CLEARANCE OF 40mm ON THE HATCHED AREA IS REQUIRED FOR SAFE OPERATION. 3.9 35 39.4 000 6.9 48 7.3 87 5.0 6 A 5.6 95 A 59. 500.4 36.5. 88 96 85 9. 740 49.0 45 SPACE REQUIREMENT BELOW MOUNTING LEVEL 3.9 35 39.4 6.9 000 48 70. 780 5. 38 SECTION AA COPYRIGHT 04 ALL RIGHTS RESERVED BY VEEM LTD. THIS DRAWING HAS BEEN ANY MANNER WITHOUT PRIOR WRITTEN APPROVAL OF VEEM LTD www.veem.com.au TEL: +6 894559355 FAX: +6 894559333 3. 060DT000.04 04 OF 0 :0 SPACE REQUIREMENTS UNDER STABILISER
Y FORCES ON MOUNT MAX MIN X 30.kN 30.kN Y 06kN 30kN Z 33.3kN 33.3kN 5. 30 70.08 780 5. 30 FORCES ON MOUNT MAX MIN X 30.kN 30.kN Y 06kN 30kN Z 33.3kN 33.3kN 59. 500 4.7 373 X Z FORE OR AFT ISOMETRIC VIEW TRANSVERSE X 8.9 7 FORCES ON MOUNT MAX MIN X 30.kN 30.kN Y 06kN 30kN Z 33.3kN 33.3kN Z FORCES ON MOUNT MAX MIN X 30.kN 30.kN Y 06kN 30kN Z 33.3kN 33.3kN NOTE: FY (VERTICAL) LOADS SHALL BE CONSIDERED TO FULLY ERSE AT THE VESSELS NATURAL ROLLING PERIOD. FX AND FZ (HORIZONTAL) LOADS SHALL BE CONSIDERED TO FULLY ERSE AT HALF THE VESSELS NATURAL ROLLING PERIOD. EACH LOAD SHALL BE CONSIDERED TO BE INDEPENDENT. ONEROUS LOAD COMBINATIONS SHALL BE CONSIDERED. FOR MORE INFORMATION CONSULT TECHNICAL NOTE 404. COPYRIGHT 04 ALL RIGHTS RESERVED BY VEEM LTD. THIS DRAWING HAS BEEN ANY MANNER WITHOUT PRIOR WRITTEN APPROVAL OF VEEM LTD www.veem.com.au TEL: +6 894559355 FAX: +6 894559333 3. FORCES ON MOUNTS 060DT000.05 05 OF 0 :0
NOTE: MIN PRELOAD 47kN ON MOUNT BOLTS, M4 GRADE 8.8 OR EQUIVALENT RECOMMENDED.0 6 7.7 96 8.7 0.4 90 HEX BOLT INTERFACE TO SHIP STRUCTURE M4 VIEW OF VIBRATION MOUNT WASHER WASHER HEX NUT 8.7 0.4 90 BOTTOM VIEW BOTTOM VIEW COPYRIGHT 04 ALL RIGHTS RESERVED BY VEEM LTD. THIS DRAWING HAS BEEN ANY MANNER WITHOUT PRIOR WRITTEN APPROVAL OF VEEM LTD www.veem.com.au TEL: +6 8 9455 9355 FAX: +6 8 9455 9333 DRAFTING TO DESCRIPTION MOUNTING INTERFACE 060DT000.06 3. 06 OF 0 :
TOP VIEW 8.7 099 80.3 040 47.0 95 57.8 468 LEFT PANEL VIEW FRONT PANEL VIEW 70.5 790 RIGHT PANEL VIEW 8.5 070 REAR PANEL VIEW 0.7 73 COPYRIGHT 04 ALL RIGHTS RESERVED BY VEEM LTD. THIS DRAWING HAS BEEN ANY MANNER WITHOUT PRIOR WRITTEN APPROVAL OF VEEM LTD www.veem.com.au TEL: +6 894559355 FAX: +6 894559333 3. INSTALLATION DRAWING 060DT000.07 07 OF 0 :0
TOP VIEW 8.6 097 8.5 070 46. 75 LEFT PANEL VIEW FRONT PANEL VIEW RIGHT PANEL VIEW 0.7 73 REAR PANEL VIEW COPYRIGHT 04 ALL RIGHTS RESERVED BY VEEM LTD. THIS DRAWING HAS BEEN ANY MANNER WITHOUT PRIOR WRITTEN APPROVAL OF VEEM LTD www.veem.com.au TEL: +6 894559355 FAX: +6 894559333 3. INSTALLATION DRAWING 060DT000.08 08 OF 0 :0
9.7 500 RECOMMENDED OPERATING AND MAINTENANCE SPACE REQUIREMENTS 9.7 500 9.7 500. 305. 305 RECOMMENDED RECOMMENDED 9.7 500. 3075 84.9 57 RECOMMENDED 3.6 600 9.7 500 4. 360 SIDE VIEW REFER TO SECTION AA 4 4. 360 NOTE: ACCESS TO NUTS UNDER VIBRATION MOUNTS IS REQUIRED EXCEPT WHERE BONDED SADDLE IS USED, REFER TO S 4 & 6 3.3 85 COPYRIGHT 04 ALL RIGHTS RESERVED BY VEEM LTD. THIS DRAWING HAS BEEN ANY MANNER WITHOUT PRIOR WRITTEN APPROVAL OF VEEM LTD www.veem.com.au TEL: +6 894559355 FAX: +6 894559333 3. INSTALLATION DRAWING 060DT000.09 09 OF 0 :0
7.3 440 MINIMUM REQUIREMENTS 5.7 400 OPERATING AND MAINTENANCE SPACE REQUIREMENTS.8 300 0. 798 0.4 805 MINIMUM MINIMUM 8.3 0 6.9 597 MINIMUM 5.7 400 5.7 400.8 300.3 33 SIDE VIEW REFER TO SECTION AA 4 NOTE: 7.3 440.6 40 ACCESS TO NUTS UNDER VIBRATION MOUNTS IS REQUIRED EXCEPT WHERE BONDED SADDLE IS USED, REFER TO S 4 & 6 8.3 0 COPYRIGHT 04 ALL RIGHTS RESERVED BY VEEM LTD. THIS DRAWING HAS BEEN ANY MANNER WITHOUT PRIOR WRITTEN APPROVAL OF VEEM LTD www.veem.com.au TEL: +6 894559355 FAX: +6 894559333 3. INSTALLATION DRAWING 060DT000.0 0 OF 0 :0