Limited Product Manual Section 2 Manual Version 23.0.1
Section 2.01 Product specifications 2.01.01 sheet 1 Ground Floor Framing - Product Specification 2.01.02 sheet 1 ommercial Entrance doors - Product Specification 2.01.03 sheet 1 DD and DLM - Product Specification Section 2 ontents Section 2.02 General arrangements. Flush glaze frames 2.02.01 sheet 1 SG Framing - Standard mullions & transoms 2.02.02 sheet 1 SG Framing Door mid-rail with KS7 transom 2.02.03 sheet 1 SG Framing Door mid-rail with KS4 transom 2.02.04 sheet 1 SG Framing - Standard mullions, KS corner post 2.02.0 sheet 1 SG Framing - Standard mullions, KS49 corner post 2.02.06 sheet 1 SG Framing - Standard mullions, KS70 corner post 2.02.07 sheet 1 DG Framing - Standard mullions & transoms 2.02.0 sheet 1 DG Framing - Standard transoms and door mid-rails 2.02.09 sheet 1 DG Framing - Standard mullions, KS46 corner post 2.02.10 sheet 1 DG Framing - Standard mullions, KS49 corner post 2.02.11 sheet 1 DG Framing - Standard mullions, KS40 corner post 2.02.12 sheet 1 SG/DG Framing KS2 options Section 2.03 General arrangements. ead glaze frames 2.03.01 sheet 1 SG Framing eaded 2.03.02 sheet 1 DG Framing eaded 2.03.03 sheet 1 SG Framing eaded & 4 corner post 2.03.04 sheet 1 DG Framing eaded & 4 corner post 2.03.0 sheet 1 SG/DG Framing eaded &, 6 and 7 options 2.03.06 sheet 1 SG/DG Framing KS71, 74, 7, 76 Section 2.04 General arrangements. Miscellaneous 2.04.01 sheet 1 SG Framing KS39 2.04.01 sheet 2 SG Framing KS39 on KS19 2.04.02 sheet 1 SG Framing KS64, 66, 6 Section 2.0 General arrangements. Pivot & rebate doors 2.0.01 sheet 1 Pivot doors Typical details 2.0.02 sheet 1 Pivot doors Typical details with fanlight KS93 2.0.03 sheet 1 Pivot doors Typical details with split fanlight KS93 2.0.04 sheet 1 Pivot doors Typical details with KS27, 67 2.0.04 sheet 2 Pivot doors Typical details with KS96, 27, 67 2.0.0 sheet 1 SG Rebate doors Typical details 2.0.06 sheet 1 SG Rebate doors Typical details with fanlight 2.0.07 sheet 1 DG Rebate doors Typical details 2.0.0 sheet 1 DG Rebate doors Typical details with fanlight 2.0.09 sheet 1 KS60 application double door & electric strike 2.0.10 sheet 1 KS60 application sliding door & trim strike 2.0.11 sheet 1 KS3/36 & KS90 details 2.0.11 sheet 2 KS79 Typical detail 02.01.00 Sheet 1 01.11.14
Section 2 ontents Section 2.0 General arrangements. Sliding doors 2.0.12 sheet 1 uto sliding doors elevations for section keys 2.0. sheet 1 uto sliding doors Typical sections door jambs 2.0.14 sheet 1 uto sliding doors Typical sections side screens 2.0.1 sheet 1 uto sliding doors Typical sections head sections 2.0.16 sheet 1 uto sliding doors Typical sections head sections 2.0.17 sheet 1 uto sliding doors Typical sections head sections 2.0.1 sheet 1 uto sliding doors Typical sections head sections 2.0.19 sheet 1 uto sliding doors Thresholds, none, KS19 x 2, 19/6 2.0.20 sheet 1 uto sliding doors Thresholds, KS, 19/9 2.0.21 sheet 1 uto sliding doors Stall riser with pressed ZED cill 2.0.21 sheet 2 uto sliding doors Stall riser with KS72 stubcill Section 2.0 General arrangements. uto swing doors 2.0.22 sheet 1 uto swing head detail open in door 2.0.23 sheet 1 uto swing head detail open out door 2.0.24 sheet 1 uto swing head detail open in door with fanlight Section 2.0 General arrangements. Manual sliding doors 2.0.2 sheet 1 Manual sliding doors elevations and details 2.0.26 sheet 1 Manual sliding doors elevations and details 2.0.27 sheet 1 Manual sliding doors elevations and details 2.0.2 sheet 1 Manual sliding doors elevations and details 2.0.29 sheet 1 Manual sliding doors elevations and details Section 2.0 General arrangements. Manual sliding/folding doors 2.0.30 sheet 1 Manual sliding/folding doors elevations and details 2.0.31 sheet 1 Manual sliding/folding doors elevations and details 2.0.32 sheet 1 Manual sliding/folding doors elevations and head details 2.0.33 sheet 1 Manual sliding/folding doors elevations and track details 2.0.34 sheet 1 Manual sliding/folding doors door types Section 2.06 Miscellaneous 2.06.01 sheet 1 Miscellaneous KS1, 16, 17 and KS10, 11, 20 sections 2.06.02 sheet 1 Top rail options - cleat codes shown 2.06.03 sheet 1 Mid rail options - cleat codes shown 2.06.04 sheet 1 ottom rail options - cleat codes shown 2.06.0 sheet 1 and gaskets SG 2.06.06 sheet 1 and gaskets DG 2.06.07 sheet 1 Wool-pile ID 02.01.00 Sheet 2 01.11.14
Ground Floor Framing - Product Specification GROUND FLOOR FRMING The ground floor framing system is for use on commercial and retail buildings and can be used in conjunction with the commercial entrance doors. Materials: luminium profiles are extruded from alloy 6060/6063 T6 complying with the recommendations of S EN 7:1-9 Finishes: Mill finish Etched and anodised to S 397: 1991 (01.06.2007) - Silver 2 or colours on request. Polyester Powder coat paint to S EN 12206-1:2004. See separate list for standard colour range available. onstruction: luminium profiles are square cut mechanically jointed and secured using stainless steel screws driven into extruded screw splines. ll joints should be sealed against water penetration., Glazing and Infil Panels: The single glazed framework is designed to accommodate glass thickness of 6mm, 6.4mm, 7.mm,.mm, 10.mm, 11.mm In addition the double glaze framework can accommodate 24 and 24.mm thick double glazing units. 2mm thickness can be glazed only in beaded frame (KS 1/2). ll glass panels should be secured in framework with glazing gaskets extruded from TPE. Glazing to be carried out in strict accordance with S 6262 and S 6206 with particular attention being taken to risk areas, which would require safety glass. The system will also accommodate solid infil panels to customers own specification and supply. Installation and Fixing: The fixing of all framework is by woodscrews through the glazing pocket into securely located plugs in the surrounding structure. It is not recommended that fixing holes are pre-drilled, as site conditions may affect their position. Where possible continuous backplates are included on perimeter framework to provide a firm fixing and bedding platform. These plates also help to eliminate frame distortion. ll fixing screws must be stainless steel or cadmium plated finish. 2.01.01 Sheet 1 01.09.0
ommercial Entrance Doors - Product Specification OMMERIL ENTRNE DOORS: ommercial Entrance Doors are designed for use as stand alone units or in conjunction with the ground floor framing system. Doors can be pivoted or hinged and are suitable for general traffic areas. The twin brush seal, woolpile weatherstripping together with an extensive suite of profiles, covers the majority of entrance door requirements. Materials: luminium profiles are extruded from alloy 6060/6063 T6 complying with the recommendations of S EN 7: 1-9 Finishes: Mill finish Etched and anodised to S 397: 1991 (01.06.2007) - Silver 2 or colours on request. Polyester Powder coat paint to S EN 12206-1:2004. See separate list for standard colour range available. onstruction: oncealed extruded aluminium mechanical corner jointing cleats and midrail brackets are used. M10 plated mild steel threaded tie rods are used with locking nuts in the top and bottom rails to ensure further rigidity. Hardware: Door hardware is available to construct and operate pivot doors with or without finger-guard door jamb stiles, rebated open in or open out doors, manual sliding doors. utomatic doors require bespoke operating gear supplied and commissioned by specialist contractors. Limited supply as standard; Hook bolt & bar bolt dead locks & relevant face plates and armour strikes, Latch locks & relevant face plates, standard strikes or electric strikes, Round or profile cylinders to suit above - key variations possible, thumbturn options, Push bar exit devices - concealed rod, face fitted rod or push paddle types, oncealed overhead closer - end or side load, face fitted closer, Letter plates, Pad and tubular handles, flush pulls, Flush bolts, Door rollers & track, Other hardware options can be obtained on request., Glazing and Infil Panels: Doors can be supplied with tamper-proof external glazing beads for security. The system is designed to accept glass of 6mm, 6.4mm, 7.mm,.mm and 10.mm. In addition the double glaze beads can accommodate 24 or 24.mm and 2mm thickness units or infil panels. Glazing to be carried out in strict accordance with S 6262 and S 6206 with particular attention being taken to risk areas, which would require safety glass. The system will also accommodate solid infil panels to customers own specification and supply. 2.01.02 Sheet 1 01.09.0
DD & DO M - Product Specification Disability Discrimination ct The table below is taken from pproved Document M of the uilding Regulations 2000 2004 edition The information given is covered by rown copyright 2003 and may only be used for private study or internal circulation within an organisation. We recommend that a copy of the pproved Document M should be obtained for further reference regarding the ccess to and the use of buildings. Download from:- www.planningportal.gov.uk/uploads/br/r_pdf_dm_2004.pdf REOMMEND THT LL DOORS SHOULD INLUDE NTI-FINGER TRP PIVOT STILES EFFETIVE LER WIDTH Table 2 Minimum Effective lear Opening Widths Direction and width of approach New uildings Existing uildings Minimium 300mm Straight-on (without a turn or oblique approach) t right angles to an access route at least 100mm wide 00 00 70 70 t right angles to an access route at least 1200mm wide 2 77 External doors to buildings used by the general public 0 77 Note: The effective clear width is the width of the opening measured at right angles to the wall in which the door is situated from the outside of the door stop on the door closing side to any obstruction on the hinge side, whether this be projecting door opening furniture, a weather board, the door, or the door stop (see diagram). for specific guidance on the effective clear widths of doors in sports accomodation, refer to 'ccess for Disabled People'. Important Note: New buildings should have an ESS STTEMENT to detail and clarify the type, purpose and operational requirements of each door. This should be used at LL stages to ensure the correct door and door hardware are specified and agreed upon between relevant parties. Other Items for consideration are:- ll door opening furniture should contrast visually with the surface of the door and is not cold to the touch. The opening force at the leading edge of a of a door should be no greater than 20N if a greater force is required There is an unobstructed space of at least 300mm on the pull side of the door between the leading edge of the door and any return wall, unless the door is power assisted (see diagram). On double doors, at least one door should be wide enough to give the minimum effective opening width Thresholds - Steps should ideally be no greater than 1mm 2.01.03 Sheet 1 01.09.0
SG Framing - Standard mullions & transoms 2.02.01 D 2.02.01 KS3 KS6 2.02.01 2.02.01 2.02.01 E 2.02.01 F 2.02.01 Fixed Glazing Typical Elevation KS7 KS6 0 KS6 KS1 D 2.02.01 SG glazing pocket = 16.0mm 16. KS7 KS6 KS6 0 KS1 KS1 E 2.02.01 KS4 2.02.01 2.02.01 KS3 KS6 KS6 10 F 2.02.01 9 ill End Plate 2.02.01
SG Framing - door mid-rail with KS7 transom KS7 KS6 0 KS6 KS3 KS6 12 KS14 Midrail 12 0 12 KS3 KS6 KS3 KS6 12 KS14 Midrail 0 KS6 10 KS6 10 9 ill End Plate 9 ill End Plate 2.02.02
SG Framing - door mid-rail with KS4 in transom KS3 KS6 KS3 KS6 KS3 KS6 KS4 *6 * Where this profile configuration is chosen, 3mm needs to be deducted from the aperture size to allow the glass to be manouvered into the framework. It should be noted that this reduces glass edge cover to 6mm. KS3 KS6 KS4 KS3 KS6 perture 0 12 9 KS14 Midrail KS6 10 KS6 10 9 ill End Plate 9 ill End Plate 2.02.03
SG Framing - Standard mullions, KS corner post Typical 3 way corner post 2.02.04 2.02.04 2.02.04 D 2.02.04 D 2.02.04 KS9 KS Fixed Glazing Typical Elevation KS9 2.02.04 KS1 KS1 KS KS4 KS9 2.02.04 2.02.04 Typical 2 way corner post 2.02.04 Sheet 1 01.0.11
SG Framing - Standard mullion, KS49 corner post 2.02.0 2.02.0 2.02.0 Fixed Glazing Typical Elevation 1 KS9 KS9 KS49 2.02.0 1 KS1 KS9 KS9 6.42 2.02.0 KS49 2.02.0 Symmetrical about centre line Typical 2 way corner post with post KS 49 6.42 2.02.0
*Use deep pocket opposite KS 70 mullion KS1 Variable 2 KS70 KS70 2 Variable SG Framing - Standard mullion, KS70 corner post N: orner as constructed can be sent to site as complete assembly 2.02.06 2.02.06 2.02.06 2.02.06 Fixed Glazing Typical Elevation KS1 * 2.02.06 * 2.02.06 2.02.06 rackets & 2mm aluminium pressing by others (fix to only) 2 Typical variable angle corner post with 1/2 mullion KS 70 2.02.06
2.02.07 DG Framing - Standard mullions & transoms 2.02.07 2.02.07 Fixed Glazing Typical Elevation D 2.02.07 E 2.02.07 F 2.02.07 KS42 2.02.07 KS4 KS44 KS44 0 0 KS44 KS41 D 2.02.07 32 DG glazing pocket = 32.00mm KS4 KS44 KS44 KS41 KS41 E 2.02.07 2.02.07 KS43 2.02.07 KS42 KS44 KS6 10 F 2.02.07 9 ill End Plate 2.02.07
DG Framing - Standard transoms & door mid-rails 24 24 KS4 KS44 KS44 0 KS47 KS42 KS44 0 KS14 0 12 KS14 12 KS42 KS44 KS42 KS44 2.02.0
DG Framing - Standard mullion, KS46 corner posts Typical 3 way corner post 2.02.09 2.02.09 2.02.09 D 2.02.09 D 2.02.09 KS47 KS46 Fixed Glazing Typical Elevation KS47 2.02.09 KS41 KS41 KS46 KS43 KS47 2.02.09 2.02.09 Typical 2 way corner post 2.02.09
DG Framing - Standard mullion, KS49 corner post 2.02.10 2.02.10 2.02.10 Fixed Glazing Typical Elevation 1 KS47 KS47 2.02.10 KS49 1 KS41 KS47 KS47 6.42 2.02.10 KS49 2.02.10 Symmetrical about centre line Typical 2 way corner post with post KS 49 6.42 2.02.10
*Use deep pocket opposite KS 40 mullion KS41 Variable 2 KS40 KS40 2 Variable DG Framing - Standard mullion, KS40 corner post N: orner as constructed can be sent to site as complete assembly 2.02.11 2.02.11 2.02.11 2.02.11 Fixed Glazing Typical Elevation KS1 * 2.02.11 2.02.11 2.02.11 rackets & 2mm aluminium pressing by others (fix to only) 2 Typical variable angle corner post with 1/2 mullion KS 40 2.02.11 Sheet 1 01.0.11
SG/DG Framing - KS2 options KS2 KS2 KS2 KS9 KS47 22. KS2 KS4 22. KS2 KS43 16. 16. KS2 KS2 2 17 17 2 KS32 24mm 2mm KS92 KS32 Single glazing frames KS 2 can be used with: KS KS 9 KS 4 KS 2 Double glazing frames KS 2 can be used with: KS KS 47 KS 43 KS 2 2.02.12 Sheet 1 01.0.11
SG Framing - eaded 2.03.01 2.03.01 2.03.01 D 2.03.01 E 2.03.01 F 2.03.01 Fixed Glazing (eaded) Typical Elevation 1 2.03.01 1 2 D 2.03.01 1 1 KS92 KS92 1 2 KS92 2.03.01 2.03.01 2 E 2.03.01 1 KS6 10 F 2.03.01 9 ill End Plate 2.03.01
DG Framing - eaded 2.03.02 2.03.02 2.03.02 Fixed Glazing (eaded) Typical Elevation 6. 4. KS 22 - Use with 24mm, 24.mm glazing. KS 32 - Use with 2mm glazing. 1 2.03.02 D 2.03.02 E 2.03.02 F 2.03.02 1 2 2.03.02 2.03.02 D 2.03.02 E 2.03.02 KS6 1 1 2 1 2 1 10 9 ill End Plate 2.03.02
SG Framing - eaded & 4 orner post Typical 3 way corner post D 2.03.03 2.03.03 2.03.03 2.03.03 2 KS92 4 Fixed Glazing (eaded) Typical Elevation KS92 2 KS92 D 2.03.03 2.03.03 1 1 2 2 KS92 4 KS92 KS92 KS92 KS92 2.03.03 2.03.03 Typical 2 way corner post 2.03.03
DG Framing - eaded & 4 orner post Typical 3 way corner post D 2.03.04 2.03.04 2.03.04 2.03.04 2 4 Fixed Glazing (eaded) Typical Elevation 2 D 2.03.04 2.03.04 1 1 2 2 4 2.03.04 2.03.04 Typical 2 way corner post 2.03.04
SG/DG Framing - KS 6, 7, options eaded framing - Miscellaneous sections 1 1 1.2 6 7 0 22 3 KS 42 or KS 42 woolpile 2 KS 7 flush infill section KS 6 rebate door infill section KS small single bead box (No screw ports) Scale 1.1 2.03.0
SG/DG Framing - KS71, 74, 7, 76 2. KS71 2. KS7 N: Ltd supply standards; Equal angles Unequal angles Square & rectangular box sections channels Flat bars round tubes 'T' sections Please see Section 10 of current price list for details 2. KS76 17. KS74 KS 74 ead (use with KS 79 nylon clips @ 20mm centres) 79 Scale 1.1 2.03.06
SG/DG Framing - KS39 2.04.01 KS 39 fixing channel Scale 1.1 Fixed Glazing Typical Elevation Double glazing shown as example 2.04.01 KS ottom Rail KS ottom Rail KS7 KS39 3 rush 22 KS1 Threshold 22 Door bottom rail into fixed frame KS bottom rail shown KS 33 alternative KS 39 fixing channel & KS42 woolpile Typical entre hung pivot door KS bottom rail shown KS 33 alternative 2.04.01 Sheet 1 01.09.0
SG/DG Framing - KS39 2.04.01 KS 39 fixing channel Scale 1.1 Fixed Glazing Typical Elevation lternative detail Double glazing shown as example 2.04.01 KS ottom Rail KS ottom Rail KS7 KS39 Seal 22 3 rush KS19 Threshold 22 Use KS19 threshold under KS39 to avoid notching of internal finishes around framing Door bottom rail into fixed frame KS bottom rail shown KS 33 alternative KS 39 fixing channel & KS42 woolpile Typical entre hung pivot door KS bottom rail shown KS 33 alternative 2.04.01 Sheet 2 01.01.09
KS 64 ladding KS 64 ladding - Pitch = 10mm Use anodised only - clip fit not suitable for powder coat finishes SG/DG Framing - KS64, KS66, KS6 KS 66 Louvre lade KS 66 Louvre - Pitch = 0mm 3 2 10 10 20 10 2 2 0 162 2 KS410 0 KS66 KS 66 Louvre lade See Manual Section 16 KS 6 sub cill 20 Use KS 9 end plates (Pairs) Scale 1.1 2.04.02 Sheet 1 01.11.14
Pivot doors - Typical details 2.0.01 KS2 Header ar KS1 Frame Jamb 700 2.0.01 2.0.01 2.0.01 D 2.0.01 Single Door Typical Elevation 2.0.01 E 2.0.01 2.0.01 D 2.0.01 Double Door Typical Elevation as 2.0.01 960 1400 as 2.0.01 KS14 Midrail KS42 Woolpile 2.0.01 0 3 rush KS24 Header Plate KS12 Top Rail KS ottom Rail KS7 KS1 Threshold 2.0.01 D 2.0.01 22 Outside KS40 Woolpile KS40 Woolpile KS29 Stile 24mm D.G Glazing ead KS2 Slave Stile KS29 Lock Stile KS7 Plate 2.0.01 E 2.0.01 Outside 4 2.0.01
Pivot doors - Typical details with fanlight KS93 H 2.0.01 F 2.0.01 2.0.01 KS42 KS44 2.0.01 H 2.0.01 2.0.01 Single Door with Fanlight Typical Elevation KS41 KS41 glass KS29 Stile F 2.0.01 24mm D.G Glazing ead KS42 Woolpile KS93 Header ar KS24 Header Plate KS12 Top Rail 12 2.0.01 0 KS 64 Small Rail 30 2.0.01 2.0.01 2.0.02
Pivot doors - Typical details with split fanlight KS93 H 2.0.03 F 2.0.03 G 2.0.03 2.0.03 KS42 KS44 H 2.0.03 KS93 eaded Header ar KS2 Plain Header ar Double Door with Split Fanlight Typical Elevation KS93 0 KS24 Header Plate KS42 Woolpile We recommend KS 93 beaded header bar for all fan light applications N KS 93 = 0mm high KS12 Top Rail 2.0.03 KS 2 = mm high 1mm Offset from entre Line KS41 KS41 KS43 F 2.0.03 G 2.0.03 2.0.03
Pivot doors - Typical details with KS27,67 J 2.0.04 2.0.04 2.0.04 D 2.0.04 700 Single Door Typical Elevation 2.0.04 960 1400 KS14 Midrail KS42 Woolpile 2.0.04 0 KS2 Header ar KS24 Header Plate KS12 Top Rail 2.0.04 KS ottom Rail D 2.0.04 KS7 KS 67 Flat face safety stile - Use with face fitted hardware. Open out single action doors only. KS67 3 rush KS1 Threshold 22 Outside KS1 Frame Jamb 70 KS40 Woolpile KS1 KS26 24mm D.G Glazing ead KS29 Stile KS7 KS27 KS7 Plate J 2.0.04 KS40 Woolpile 2.0.04 Plate Outside 2.0.04
Pivot doors - Typical details with KS96, KS27,67 42.2 J 2.0.04 KS47 KS2 Fixing to plain mullion Fix KS96 to KS2 or as shown No 10 47 Single Door Typical Elevation Outside J 2.0.04 KS40 Woolpile KS41 Frame Jamb 70 KS43 KS41 Fixing to DG mullion KS Existing KS27 Pre-fix KS7 or KS to KS96 to enable a clip fit to SG/DG door hinge jamb sections with glazing pocket J 2.0.04 KS40 Woolpile Outside 97 KS1 Frame Jamb 70 KS3 KS1 Fixing to SG mullion KS7 KS 67 Flat face safety stile - Use with face fitted hardware. Existing KS67 Open out single action doors only. J 2.0.04 KS40 Woolpile Outside 97 2.0.04 Sheet 2 01.01.10
SG Rebate doors - Typical details 2.0.0 Single Door Typical Elevation 0 2.0.0 2.0.0 D 2.0.0 E 2.0.0 2.0.0 KS14 Midrail KS1 KS61 KS12 Top Rail KS219 2.0.0 12 Outside KS ottom Rail D 2.0.0 Double Door Typical Elevation KS1 Frame Jamb Plate KS61 Rebate 2 KS40 Woolpile KS29 Stile KS460 lternative KS63 Rebated Threshold KS460 ubble Seal KS37 3 rush 22 KS2 Slave Stile 3H rush 3 rush KS40 Woolpile KS1 Threshold KS29 Lock Stile KS37 22 KS92 KS92 KS92 2.0.0 E 2.0.0 Outside 4 2.0.0 Sheet 1 01.09.0
SG Rebate doors - Typical details with fanlight F 2.0.06 H 2.0.06 2.0.06 2.0.06 Single Door with Fanlight Typical Elevation 2.0.06 H 2.0.06 2.0.06 KS4 KS61 KS3 KS6 KS6 KS3 KS219 KS12 Top Rail KS34 Deep mid rail KS1 170 F 2.0.06 2.0.06
DG Rebate doors - Typical details 2.0.07 KS41 2.0.07 2.0.07 D 2.0.07 Single Door Typical Elevation E 2.0.07 2.0.07 KS14 Midrail 0 KS62 KS12 Top Rail KS219 2.0.07 Outside KS ottom Rail D 2.0.07 Double Door Typical Elevation KS41 Frame Jamb Plate KS62 Rebate 2 KS40 Woolpile KS29 Stile KS460 lternative KS63 Rebated Threshold KS460 ubble Seal KS37 3 rush 24mm D.G Glazing ead 22 KS2 Slave Stile 3H rush 3 rush KS40 Woolpile KS1 Threshold KS29 Lock Stile KS37 22 2.0.07 E 2.0.07 Outside 4 2.0.07 Sheet 1 01.09.0
DG Rebate doors - Typical details with fanlight H 2.0.0 F 2.0.0 2.0.0 2.0.0 Single Door with Fanlight Typical Elevation 2.0.0 KS42 H 2.0.0 2.0.0 KS42 KS43 KS62 KS44 KS44 KS219 KS12 Top Rail KS41 KS34 Deep mid rail 170 F 2.0.0 2.0.0
Double Door Meeting Stiles with Hook Lock KS 60 - application - double door & electric strike Minimum learance 4mm Lock /set 30 20 Escutcheon 0d Hook Lock KS60 39. 27. 47 KS42 Woolpile Weatherstripping rimp the Profile to Retain the Woolpile Screw Fix KS60 with x No6 Pozi sk. Twinfast Screws ZP at nom. 200mm ctrs. Double Door Meeting Stiles with Latch lock and Electric Strike Minimum learance 4mm min. Lock /set 2.6 See DRG 3.12.01 sheets 1-6 for KS 40 electric strike in frames 20 Escutcheon 41 Latch Lock KS60 39. 27. 47 Scale 1.1 2.0.09
KS 60 - application - sliding door & trim strike Sliding Door Meeting Stiles with Hook Lock Minimum learance 4mm Lock /set 30 20 Escutcheon Hook Lock KS60 39. 27. 47 KS42 Woolpile Weatherstripping rimp the Profile to Retain the Woolpile Screw Fix KS60 with x No6 Pozi sk. Twinfast Screws ZP at nom. 200mm ctrs. Double Door Meeting Stiles with Latch lock and Trim Strike min. Lock /set 2.6 Minimum learance 4mm Some Modification to the Trim Strike Plate may be necessary to allow and ensure that the latch engages correctly 20 Escutcheon 06b Latch Lock KS60 39. 27. 47 Scale 1.1 2.0.10
KS 3 / 36 & KS 90 details 2 KS ottom Rail. Silicone Sealant in Severe onditions KS36 (in 3M Lengths) No Self Tapping Screws KS3 (in 3M Lenghts) 3 rush * (in 3M Lengths) 12. KS1 Threshold ottom pivot and lock nut 7 1 KS90 Drain Threshold Mild steel plated tapping block 6mm Ø lear Holes for Drainage * 3H High Draft Seal rush also available Scale 1.1 2.0.11 Sheet 1 01.09.0
KS 79 detail KS ottom Rail KS7 Silicone sealant No6 x 1/2" Pan head self tapping screw 3 KS40 22 12. KS1 Threshold KS79 Use drip bar at threshold as shown on pivot door - Ends will require mitre cut on plan to avoid clashing with KS26 if used. 21.1 KS79 Do not use on sliding or sliding/folding doors KS79 or KS219 can be used to protect head of open out rebated doors, with or without wool-pile inserted. 27. Scale 1.1 2.0.11 Sheet 2 01.0.11
Typical bi-parting sliding door elevation uto sliding doors - elevations for section keys G 2.0.16 H 2.0.1 2.0.14 2.0. 2.0. Slide Slide K 2.0.21 J 2.0.19 J 2.0.20 Typical single sliding door elevation with glazed fanlight L 2.0.17 M 2.0.1 See pages 2.0. - 21 incl. for typical details as indicated. IMPORTNT NOTE: D 2.0. E 2.0. F 2.0.14 These are typical details only! Slide Setting out of door leafs and header bars etc. dependant on specific operator design per supplier - ontact supplier for door leaf / header bar details. 2.0.12
uto sliding doors - Typical sections door jambs 7. 0 Length of 17 KS4 M6 * 30 Meeting Stile in Open Position 102 minimum (to avoid finger trap) KS92 KS2 Meeting Stile in losed Position 4 KS29 KS92 2.0. KS7 KS4 2.0. KS1 KS 30 KS 3 used on plain mm stile - check gap and woolpile height to avoid binding when leaf is closing Gap KS 3 KS2 KS29 KS92 KS92 KS4 4 KS7 KS7 KS1 KS4 D E 2.0. 2.0. KS1 2.0.
uto sliding doors - Typical sections side screens KS409 butt hinge KS92 KS92 KS2 71.F & G top & bottom * KS7 KS1 * Internal safety screen optional - * see note regarding gap to clear sliding leaf *onfirm Gap KS4 KS92 KS7 KS1 2.0.14 s 2.0. KS1 KS4 s E 2.0. No internal safety screen shown KS92 KS4 KS7 KS4 F 2.0.14 KS1 KS1 2.0.14
uto sliding doors - Typical sections head sections KS2 heck clearance required to open cover KS70 KS3 Use KS 70 to reduce the overall height of the header bar - N See note on opening the cover 21 Typical uto Unit KS1 KS7 KS Outside Safety screen if required 19 H 2.0.1 47 2.0.1
uto sliding doors - Typical sections head sections KS2 heck clearance required to open cover KS70 KS3 Use KS 70 to reduce the overall height of the header bar - N See note on opening the cover 21 Typical uto Unit Outside Safety screen if required 19 KS3 KS6 G 2.0.16 Sliding door leaf 2.0.16
uto sliding doors - Typical sections head sections heck clearance required to open cover KS3 21 Typical uto Unit KS1 KS7 KS Outside Safety screen if required KS3 KS6 L 2.0.17 47 2.0.17
uto sliding doors - Typical sections head sections heck clearance required to open cover KS3 21 Typical uto Unit KS3 KS6 Outside Safety screen if required Sliding door leaf KS3 KS6 M 2.0.1 2.0.1
uto sliding doors - Thresholds 19x2, 19/6 KS Typical bottom rail No threshold Outside J 2.0.19 KS7 10 FFL 3 KS Typical bottom rail KS 19 threshold x 2 Outside KS7 J 2.0.19 10 FFL FFL J 2.0.19 Raised floor level internally 3 KS19 KS 3 KS6 M6 M6 KS7 KS19 Typical bottom rail KS 19 / 6 thresholds Only use with raised floor internally i.e. tiled KS19 12. 10 Outside 12. 2.0.19
uto sliding doors - Thresholds 19/9 & KS Typical bottom rail KS 19/9 thresholds Outside J 2.0.20 KS7 10 FFL KS9 3 M6 KS19 10 KS 19/9 thresholds used with multiple internal door leafs or safety screens 12. KS Typical bottom rail KS threshold Outside FFL J 2.0.20 KS 10 3 KS7 M6 3H KS threshold used with multiple internal door leafs or safety screens 12. 10 2.0.20
uto sliding doors - stall riser KS3 KS6 Will apply to any frame type where stall riser is present Pressed angle or zed tray to provide drainage cill under mullion & transoms (vailable as made to order item only) Seal continuously at rear of framing K 2.0.21 Typical stall riser to construction details 2.0.21
uto sliding doors - stall riser KS3 KS6 1 KS72 Will apply to any frame type where stall riser is present KS72 stubcill with drain slots to external face Seal continuously at rear of framing K 2.0.21 Typical stall riser to construction details 2.0.21 Sheet 2 01.0.11
uto swing - Head detail - Open in door 2.0.22 lternative box section KS72 Single Door Typical Elevation Typical uto Unit KS0 10 KS93 7.E 12 0 KS24 KS77 Deep top rail KS 77 used to allow easier fitting of operating arm Outside Door opens IN uto swing doors must be constructed with finger guard stile KS 26/96 & KS 27/67 on hinge jamb 2.0.22 See page 2.0.04 for typical details 2.0.22 Sheet 1 01.11.14
uto swing - Head detail - Open out door 2.0.23 uto swing doors must be constructed with finger guard stile KS 26/96 & KS 27/67 on hinge jamb See page 2.0.04 for typical details Single Door Typical Elevation Subject to size of operator unit additional sections may be required at head to provide clearance to structure and internal reveal etc. KS 72 shown as example Typical uto Unit KS72 17 KS93 7.E 0 KS24 KS77 Deep top rail KS 77 used to allow easier fitting of operating arm Outside 12 Door opens OUT 2.0.23 2.0.23 Sheet 1 01.11.14
2.0.24 uto swing - Head detail - Open in door with fan light uto swing doors must be constructed with finger guard stile KS 26/96 & KS 27/67 on hinge jamb See page 2.0.04 for typical details Single Door Typical Elevation Typical uto Unit KS0 19 KS93 7.E 0 KS24 KS77 Deep top rail KS 77 used to allow easier fitting of operating arm Outside KS3 KS6 Door opens IN 2.0.24 2.0.24
Manual sliding doors - elevation & details 2.0.2 KS 1 ROLLERS Max. Glazed door leaf weight 200 KG./Pair 2.0.2 Manual i Parting Doors Typical Elevation 30 KS1 6 M6 1 3/4" x 1" x 1/" channel anti lift blocks (mm) KS2 Use KS1 & KS7 if concealed fixings are required at head KS77 KS 40 or KS40 2.0.2 Locate anti lift blocks over roller positions where possible Outside 9 KS77 2.0.2 Example shows track and thresholds fixed to top of floor level KS 37 uses KS 3 or KS 3 H draft strips KS 19 KS 37 KS 1 10 KS2 TRKS MUST STRIGHT and LEVEL KS 19 JMS MUST E STRIGHT and PLUM 12. FFL Denotes 10.7mm thick support blocks between roller KS 1 & KS37 (Not by Kestrel) 2.0.2 Sheet 1 01.09.0
Manual sliding doors - elevation & details D 2.0.26 2.0.26 E 2.0.26 KS 1 ROLLERS Max. Glazed door leaf weight 200 KG./Pair TRKS MUST STRIGHT and LEVEL JMS MUST E STRIGHT and PLUM Manual i Parting Doors Typical Elevation N KS 60 does NOT clear KS 1 4 Lock /set 30 KS60 KS42 Woolpile 20 Escutcheon KS30 0.P 23 KS31 E 2.0.26 Hook Lock 04.H KS92 KS92 KS60 27. Screw Fix KS60 with x No6 Pozi sk. Twinfast Screws ZP at nom. 200mm ctrs. KS30 71.F & G top & bottom 47 KS41 Woolpile KS92 9 KS3 KS1 KS1 2.0.26 D 2.0.26 2.0.26
Manual sliding doors - elevation & details F 2.0.27 KS 1 ROLLERS Max. Glazed door leaf weight 200 KG./Pair F 2.0.27 TRKS MUST STRIGHT and LEVEL JMS MUST E STRIGHT and PLUM Manual i Parting Doors Typical Elevation 16 KS3 KS6 Track & guide detail for 4 panel door - See drg 2.0.29 sheet 1 F 2.0.27 G 2.0.27 KS3 KS6 2.0.27
Manual sliding doors - elevation & details H 2.0.2 KS 1 ROLLERS Max. Glazed door leaf weight 200 KG./Pair TRKS MUST STRIGHT and LEVEL JMS MUST E STRIGHT and PLUM Manual i Parting Doors Typical Elevation Line of KS 19 KS 2 will need cut out as hatch to fit into head section KS 1 Line of KS 1 & KS 2 KS2 20 Escutcheon 0.P 23 KS31 Hook Lock 04.H KS92 9 47 4 16 KS7 KS1 H 2.0.2 Line of KS 19 Outside 2.0.2
Manual sliding doors - elevation & details H 2.0.29 s H 2.0.29 Manual i Parting Doors Typical Elevation Four panel door KS 1 ROLLERS Max. Glazed door leaf weight 200 KG./Pair TRKS MUST STRIGHT and LEVEL JMS MUST E STRIGHT and PLUM H 2.0.29 KS30 47 KS3 KS92 2 x KS41 Woolpile KS3 47 1 KS92 KS30 04. ar olt Lock (2mm /Set) with KS 27 Profile ylinder and KS 20 Flat Escuthceon Plates Outside N: rass track alternative available to special order - please ask for details 2.0.29
Manual sliding/folding doors - elevation & details 2.0.30 2.0.30 Sliding Folding door sets Vistafold operating gear Maximum door sizes: Weight per leaf = 70 kg Width per leaf = 900 mm Height per leaf = 2700mm Manual Sliding/Folding Doors Typical Elevation Three panel door ombinations of three or five panel doors sets are possible TRKS MUST STRIGHT and LEVEL JMS MUST E STRIGHT and PLUM Three Leaf Plan 20 See drg 2.0.31 also KS 71.F Inside KS 71.F to top and bottom of stile (1mm throw) 10 20. KS1 KS29 KS92 KS29 KS29 KS61 10 2.0.30 2.0.30 4 4 Pack hinge jambs full height to prevent distortion when fixing Outside 2.0.30
Manual sliding/folding doors - elevation & details D 2.0.31 2.0.31 Sliding Folding door sets Vistafold operating gear Maximum door sizes: Manual Sliding/Folding Doors Typical Elevation Three panel door ombinations of three or five panel doors sets are possible Weight per leaf = 70 kg Width per leaf = 900 mm Height per leaf = 2700mm TRKS MUST STRIGHT and LEVEL JMS MUST E STRIGHT and PLUM Three Leaf Plan This leaf acts as locking/access leaf: Open in rebated door leaf with hook bolt dead locks N: Door leaf cannot have projecting handles/furniture internally Door leaf cannot have overhead closers/restrictor arms or powered closers etc. Inside 10 Hook Lock 0.P 04.H KS29 KS29 KS92 KS92 KS29 23 KS61 2.0.31 D 2.0.31 KS1 4 4 Outside 2.0.31
Manual sliding/folding doors - elevation & head details E 2.0.32 Sliding Folding door sets Vistafold operating gear Maximum door sizes: Manual Sliding/Folding Doors Typical Elevation Three panel door ombinations of three or five panel doors sets are possible Weight per leaf = 70 kg Width per leaf = 900 mm Height per leaf = 2700mm TRKS MUST STRIGHT and LEVEL JMS MUST E STRIGHT and PLUM lternative head detail with beads to give fan light option over doors Inside Outside 17 4 Top guide KS61 KS12 Flush bolt position (1mm throw) at head section See 2.0.30 KS6 KS6 KS61 1 E E 2.0.32 2.0.32 20. 2.0.32 Sheet 1 01.11.0
Manual sliding/folding doors - elevation & track details Sliding Folding door sets Vistafold operating gear Maximum door sizes: F 2.0.33 Manual Sliding/Folding Doors Typical Elevation Three panel door ombinations of three or five panel doors sets are possible Weight per leaf = 70 kg Width per leaf = 900 mm Height per leaf = 2700mm TRKS MUST STRIGHT and LEVEL JMS MUST E STRIGHT and PLUM Inside Outside F 2.0.33 F 2.0.33 47 20. Flush bolt position (1mm throw) at track section See 2.0.30 ottom roller 4. KS KS37. Line of door stile KS69 1 KS69 26 Internal floor finish Inside Outside. 12. KS9 lternative threshold detail with KS 9 track to give flush floor level 2.0.33 Sheet 1 01.01.10
Manual sliding/folding doors - types Typical arrangements - all leafs fold to one side. Typical Three panel door - hinged to one side. Typical Five panel door - hinged to one side. Typical arrangement with sliding folding and single hinged leaf opposite (ok with 3 & panel designs). Typical Three panel door - hinged to one side with single opposing hinged leaf. System allows for all door leafs to fold to the internal side only and allows use of fully rebated head and jamb sections, rebated track/threshold profile can be used to provide rebate to all four sides for improved weathering. lternative track (KS 9) will give flush floor levels internally & externally if preferred. 2.0.34 Sheet 1 01.01.10
Miscellaneous - KS1,16,17, 10,11,21 sections Single Glaze beads - 1mm - Kestrel recommend KS 91 & 92 (17mm) 1 KS1 KS16 KS17 R0 47 KS 10 - Plain Radius Stile KS 20 - leat 47 KS 11 - Single Woolpile Radius Stile 47 KS 21 - Single Woolpile Wide Stile Scale 1.1 2.06.01
Top rail options. leat codes shown Top Rails - options 16 16 7. KS 12 - mm top rail KS 90.12 ut and prepared cleat (Ex KS20) KS 77 - mm top rail KS 90.77 ut and prepared cleat (Ex KS20) KS - mm top rail (uto sliding doors) KS 90. ut and prepared cleat (Ex KS20) Scale 1.1 2.06.02
Mid rail options. leat codes shown Mid Rails & Laybars - options 170 0 30 KS - 30mm mid rail KS 90. ut and prepared cleat (Ex KS20) 10 KS 9-10mm laybar No cleat ngle brackets reqd (Not by Kestrel) KS 14-0mm mid rail KS 90.14 ut and prepared cleat (Ex KS20) KS 34-170mm mid rail KS 90.34 ut and prepared cleat (Ex KS20) Scale 1.1 2.06.03
ottom rail options. leat codes shown ottom Rails - options KS 77 See drawing 2.06.02 Sheet 1 Used as bottom rail on manual sliding doors only 10 KS - mm bottom rail KS 90. ut and prepared cleat (Ex KS20) 3. 3. KS 33-10mm bottom rail KS 90.33 ut and prepared cleat (Ex KS20) Scale 1.1 2.06.04
& gaskets - SG Pocket framing Retaining Gasket Wedge Gasket Thickness Wedge Gasket & Gaskets SG Wedge Gasket KS 471 KS 476 6mm KS 476 KS 476 KS 471 KS 476 6.4mm KS 476 KS 476 KS 472 KS 477.mm KS 477 KS 477 KS 473 KS 47 10mm KS 47 KS 47 KS 473 KS 47 10.mm KS 47 KS 47 16. 11.mm KS 479 KS 479 & gaskets - SG beads Retaining Gasket Wedge Gasket Thickness Wedge Gasket Wedge Gasket KS 471 KS 476 6mm KS 476 KS 476 KS 471 KS 476 6.4mm KS 476 KS 476 KS 472 KS 477.mm KS 477 KS 477 KS 473 KS 47 10mm KS 47 KS 47 KS 473 KS 47 10.mm KS 47 KS 47 16. 11.mm KS 479 KS 479 & gaskets - SG bead framing - s SG beads N - Extrusion glazing pockets and glass thickness have tolerances and may vary from standard sizes on drawings. lways take alternative gaskets to site (thicker & thinner) to avoid delays in glazing up 2.06.0 Sheet 1 01.11.14
& gaskets - DG Pocket framing Retaining Gasket Wedge Gasket Thickness Wedge Gasket & Gaskets DG Wedge Gasket KS 473 KS 477 24mm KS 477 KS 477 KS 473 KS 477 24.mm KS 477 KS 477 32 N 2mm glass thickness can only be glazed in bead frame sections KS 1/2/4 with KS 32 glazing bead See below & gaskets - DG beads KS 22 Retaining Gasket Wedge Gasket Thickness Wedge Gasket Wedge Gasket KS 473 KS 477 24mm KS 477 KS 477 KS 473 KS 477 24.mm KS 477 KS 477 6. & gaskets - DG beads KS 32 Retaining Gasket Wedge Gasket Thickness Wedge Gasket Wedge Gasket KS 473 KS 477 2mm KS 477 KS 477 KS 473 KS 477 2.mm KS 477 KS 477 4. & gaskets - DG bead framing - S DG beads (KS 22 & 32) KS32 KS32 N - Extrusion glazing pockets and glass thickness have tolerances and may vary from standard sizes on drawings. lways take alternative gaskets to site (thicker & thinner) to avoid delays in glazing up 2.06.06 Sheet 1 01.09.0
Woolpile ID KS No. Reference Match Profile Design Gap KS40 6.7 6.7 900 KS29 KS31 KS1 Grey Woolpile KS41 12 11.0 900 11 KS3 Grey Woolpile KS41 KS42 4. 9 9 KS4 KS73 Grey Woolpile KS40 6.7 6.7 1200 lternative to above and KS11 KS26 KS21 KS96 11.0 00 4. 600 lternative to above KS24 6 6 KS39 Grey Woolpile KS42 4. 900 4. 9 KS61 KS63 KS62 KS24 Grey Woolpile KS460 Recommended for KS61, 62 and 63 lack TPR ubble Seal 3 12 2.2 KS36 KS7 KS37 lack rush Strip 3H 24 lack rush Strip 2.2 KS36 KS7 KS37 2.06.07 sheet 1 01.11.14