E M C C o m p o n e n t s July 0 Common Mode Filters For power line ACM series ACM50 ACM7060 ACM9070 ACM ACM5 [808 inch]* [8 inch] [68 inch] [8 inch] [605 inch] * Dimensions Code JIS[EIA]
(/5) REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than months. Be sure to follow the storage conditions (Temperature: 5 to 0 C, Humidity: 0 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 50 C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. () Aerospace/Aviation equipment () Transportation equipment (cars, electric trains, ships, etc.) () Medical equipment () Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (0) Electric heating apparatus, burning equipment () Disaster prevention/crime prevention equipment () Safety equipment () Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment.
(/5) Common Mode Filters For power line Overview of the ACM Series Product compatible with RoHS directive Halogen-free Compatible with lead-free solders FEATURES Chip common mode filter for large current applications. For each series, there is excellent common mode impedance and noise suppression in a compact case. ACM50 Low profile and small size makes it optimal for surface mounting. ACM7060, 9070,, 5 Compatible with high-density portable devices, which are always being made smaller and lighter, because the height has been reduced. APPLICATION ACM50 Power line noise countermeasure for electronic equipment (DVCs, DVD cams, DSCs, etc.). ACM7060, 9070,, 5 Power line noise countermeasure for various electronic equipment. Noise countermeasure for adapter lines and battery lines or larger electronic equipment such as note book PCs and word processors. PART NUMBER CONSTRUCTION ACM 50-90 - P - T - Series name L W H Dimensions Impedance (mm) ( ) at 00MHz Number of lines Packaging style Internal code 50.5.0.0 90 900 P lines T ø80mm reel 7060 7.0 6.0.5 00 TL ø0mm reel 9070 9.0 7.0.5.0.0*6.0 5 5.0.0 6.0 OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Type Operating temperature Temperature range Storage temperature Reel diameter Package quantity Individual weight C C mm pieces/reel g ACM50 0 to +85 0 to +85 ø80 800 ø0,500 0.5 ACM7060 0 to +85 0 to +85 ø0,500 0.5 ACM9070 0 to +85 0 to +85 ø0 800 0.8 ACM 0 to +85 0 to +85 ø0 500. ACM5 0 to +85 0 to +85 ø0 500.5 The Storage temperature range is for after the circuit board is mounted. RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/ Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 500ppm.
(/5) Overview of the ACM Series RECOMMENDED REFLOW PROFILE Preheating Soldering Peak T Natural cooling T: Temperature T T t T T t t t: Time Preheating Soldering Peak Temp. Time Temp. Time Temp. Time T T t T t T t 50 C 80 C 60 to 0s 0 C 0 to 0s 5 C 5s
(5/5) ACM series ACM50 Type SHAPE & DIMENSIONS.7±0..5.5±0. 0.65 Ferrite 0.65.0max. Wire 0.75.0 0.75 RECOMMENDED LAND PATTERN.5.5.5 CIRCUIT DIAGRAM 0.95.05 0.95.0 No polarity
(6/5) ACM series ACM50 Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Common mode impedance ( ) [at 00MHz] DC resistance ( )max. [ line] Rated current (A)max. : Includes packaging style indication (T: ø80mm reel, TL: ø0mm reel). Measurement item Product No. Manufacturer Common mode impedance 99A Agilent Technologies DC resistance 8A Agilent Technologies Insulation resistance 9A Agilent Technologies Rated voltage (V)max. Insulation resistance (M )min. Part No. min. typ. 60 C 85 C 80 0 0.05.0.6 50 0 ACM50--P- - 00 0 0.055.8. 50 0 ACM50--P- - 650 900 0.06..0 50 0 ACM50-90-P- - 000 00 0.08.7.5 50 0 ACM50--P- - IMPEDANCE VS. FREQUENCY CHARACTERISTICS 0000 000 90 Common mode Common mode Impedance (Ω) 00 Common mode Differential mode Differential mode 90 Differential mode 0 Common mode Differential mode 0 00 000 Frequency (MHz) Product No. Manufacturer 99A Agilent Technologies
(7/5) ACM series ACM7060 Type SHAPE & DIMENSIONS 7.0±0..5±0..0typ..5±0..5max. 6.0±0..5±0..5±0..5±0. RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM.5.5.5.5.0.5 No polarity
(8/5) ACM series ACM7060 Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Common mode impedance DC resistance Insulation Rated current Rated voltage ( ) [00MHz] (m )max. resistance (A)max. (V)max. min. typ. [ line] (M )min. Part No. 5 00 0 5 0 80 ACM7060-0-PL-TL0 500 700 5 0 80 ACM7060-70-PL-TL0 Measurement item Product No. Manufacturer Common mode impedance 99A Agilent Technologies DC resistance 8A Agilent Technologies Insulation resistance 9A Agilent Technologies IMPEDANCE VS. FREQUENCY CHARACTERISTICS 0000 000 70 Differential mode Impedance (Ω) 00 70 Common mode 0 Common mode 0 Differential mode 0 0 00 000 Frequency (MHz) Product No. Manufacturer 99A Agilent Technologies
(9/5) ACM series ACM9070 Type SHAPE & DIMENSIONS 9.0±0. 7.0±0..5±0. 6.0typ..5±0..5max..5±0..5±0..0±0. RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM.5 6.0.5.5.0.5 No polarity
(0/5) ACM series ACM9070 Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Common mode impedance DC resistance Insulation Rated current Rated voltage ( ) [00MHz] (m )max. resistance Part No. (A)max. (V)max. min. typ. [ line] (M )min. 500 700 0 5 0 80 ACM9070-70-PL-TL0 Measurement item Product No. Manufacturer Common mode impedance 99A Agilent Technologies DC resistance 8A Agilent Technologies Insulation resistance 9A Agilent Technologies IMPEDANCE VS. FREQUENCY CHARACTERISTICS 0000 000 Impedance (Ω) 00 70 Common mode 70 Differential mode 0 0 00 000 Frequency (MHz) Product No. Manufacturer 99A Agilent Technologies
(/5) ACM series ACM Type SHAPE & DIMENSIONS.0±0..0±0..±0. 7.typ..±0. 6.0max..7±0..7±0..5±0. RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM.7.5.7 No polarity. 7.6.
(/5) ACM series ACM Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Common mode impedance DC resistance Insulation Rated current Rated voltage ( ) [00MHz] (m )max. resistance (A)max. (V)max. min. typ. [ line] (M )min. Part No. 500 700 6 8 0 80 ACM-70-PL-TL0 750 000 6 0 80 ACM-0-PL-TL0 Measurement item Product No. Manufacturer Common mode impedance 99A Agilent Technologies DC resistance 8A Agilent Technologies Insulation resistance 9A Agilent Technologies IMPEDANCE VS. FREQUENCY CHARACTERISTICS 0000 0 Differential mode 000 0 Common mode 70 Differential mode Impedance (Ω) 00 70 Common mode 0 0 00 000 Frequency (MHz) Product No. Manufacturer 99A Agilent Technologies
(/5) ACM series ACM5 Type SHAPE & DIMENSIONS 5.0±0.5.0±0..±0. 0.typ..±0. 6.0max..7±0..8±0..7±0. RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM. 0...7.8.7 No polarity
(/5) ACM series ACM5 Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Common mode impedance DC resistance Insulation Rated current Rated voltage ( ) [00MHz] (m )max. resistance Part No. (A)max. (V)max. min. typ. [ line] (M )min. 50 550 0 0 50 ACM5-55-PL-TLHF Measurement item Product No. Manufacturer Common mode impedance 99A Agilent Technologies DC resistance 8A Agilent Technologies Insulation resistance 9A Agilent Technologies IMPEDANCE VS. FREQUENCY CHARACTERISTICS 0000 Impedance (Ω) 000 00 70 Common mode 70 Differential mode 0 0 00 000 Frequency (MHz) Product No. Manufacturer 99A Agilent Technologies
(5/5) ACM series Packaging style REEL DIMENSIONS.0±0.5 E N Type A W W N E ACM50 ø0±.5±0.5 7.5± 00± typ. ø80± ±0. 7±. 60+/ 0 typ. ACM7060 ø0± 6.+/ 0 0. typ. 00± typ. ACM9070 ø0± 6.+/ 0 0. typ. 00± typ. ACM ø0±.+/ 0 8. typ. 00± typ. ACM5 ø0±.+/ 0 8. typ. 00± typ..0 A ø.0±0. ø.0±0.8 W W TAPE DIMENSIONS ød0 P P0 F E t B W A P K Type A B ød0 E F P0 P P W K t ACM50.75±0. 5.05±0..55+0./0.75±0. 5.5±0.05.0±0. 8.0±0..0±0.05.0±0..05±0.05 0.±0. ACM7060 6.6±0. 7.6±0..5+0./0.75±0. 7.5±0..0±0. 8.0±0..0±0. 6.0±0..6±0. 0.±0.05 ACM9070 7.6±0. 9.6±0..5+0./0.75±0. 7.5±0..0±0..0±0..0±0. 6.0±0..6±0. 0.±0.05 ACM.5±0..5±0..5+0./0.75±0..5±0..0±0. 6.0±0..0±0..0±0. 6.±0. 0.5±0.05 ACM5.±0. 5.5±0..5+0./0.75±0..5±0..0±0. 6.0±0..0±0..0+0./ 0. 7.±0. 0.±0.05 500 to 560min. 60min. Taping 0min. Drawing direction