PrivaSEE Single Track Sliding Frameless System Nana Wall Systems, Inc. 100 Meadowcreek Drive #250 Corte Madera, CA 94925 800 873 5673 415 383 3148 Fax 415 383 0312 info@nanawall.com nanawall.com
Table of Contents TOOLS Rev. May 8 2017 Page Level at least 6'0" 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Required Tools Rough Opening and Unit Dimensions Head Track in "kd" (knocked down) Condition Head Track Connector for Sidejamb Assembly of Head Track Head Track Shimming Installation of Floor Closer for Single Action Offset End Panel Installation Sequence of Panels Panel Alignment and Height Adjustment Drilling Holes for Floor Sockets Panel Installation for non-entry Single Action Offset End Panel and Single Action End Panel with Floor Closer Field Applying Vertical H- and h-gaskets and Height Adjustment of ottom Compression Seal Installation of Mortise Cylinder (on Inside only) 1 1 4 " 32 Core Drill it for Pivot Point 1" 25 Core Drill it for Eccentric Floor Socket Metric Tape Measure 5 8 Drill Crowbar Soft Face Hammer Metric Tools Supplied in Accessory ox Wrench 22mm Wrench 19mm Wrench 17mm 2mm allen wrench 2,5mm allen wrench 3mm allen wrench 4mm allen wrench 5mm allen wrench 6mm allen wrench NanaWall Product Drawing Wrench 11mm Wrench 10mm PrivaSEE SHEET 1 OF 13
Rough Opening Dimensions - after applying all deadloads max. deflection of header the lesser of L/720 or 1/4" - the weight of a panel with 1/2" glass is 8 lbs/sqft Unit Dimensions - leave enough shim space to surrounding condition 3 4 " 19 3 4 " 19 1 2 " 13 1 2 " 13 #1 #2 #3 PrivaSEE SHEET 2 OF 13
9 13 250 9 13 250 Head Track in "kd" Condition 9 13 250 Top Track Comes Pre-Drilled NanaWall does not provide nor take responsibility for sizes, location or frequency of perimeter fasteners. [2"] 50 L-Profile for drop down ceiling can't be installed where a radius is located [2"] 50 3 8 " 9 L-Profile in 9'6" length (2900mm) for drop down ceiling to be cut in the field optional by NanaWall 1 2 " 13 PrivaSEE SHEET 3 OF 13
Head Track Connector for Side Jamb Top Connector Piece (Side Jambs and Head Track) PrivaSEE SHEET 4 OF 13
Assembly of Head Track 2x A Suggested Side Jamb Fastening Points: A - about 4" from interior edge - single action offset end panel side; approx. distance every 16" from the bottom using one extra screw at the bottom 2x 2x Support Structure by others A A RHT Removable Head Track 2x A PrivaSEE SHEET 5 OF 13
Finished Floor to ottom of Head-Track Height Head Track Shimming FFL PrivaSEE SHEET 6 OF 13
Installation of Floor Closer for Single Action Offset End Panel Step 1 Mark or measure position for center point of floor closer axle Step 2 Take off side jamb and unscrew bottom hinge Step 3 Cut out hole for floor closer Step 4 Install floor closer and fix it temporarily in place Step 5 Reinstall side jamb and screw bottom hinge back on 2 1 2 " 63 1'1 7 341 2 1 8 " 54 3 1 78 Wall 2 5 8 " 66 4 1 8 " 105 2" 51 1'2 1 8 " 358 PrivaSEE SHEET 7 OF 13
Installation Sequence of Panels Shown on Top of the Elevation of Product Drawing Panel #2 Panel #1 Panel #2 Step 2 Step 1 RHT (Sheet 4) Panel #2 Panel #1 RHT (Sheet 4) Step 0 Step 1 Step 2 Step 3 Panel Installation Sequence PrivaSEE SHEET 8 OF 13
Panel Alignment and Height Adjustment 3 4 Panel #3 must fit #1 #2 3 4 Don't Drill Holes for Sockets, yet! Set screw to secure axle from turning FFL 1 4 " 7 PrivaSEE SHEET 9 OF 13
Step 1 Drilling Holes for Floor Sockets Chalk Line to Match Centerline of Top-Track Step 3 Step 2 Push Tape Step 4 5 8 Eccentric Floor Socket Tape Lift Step 5 Centerpoint Centerpoint Mark Min. 1 3 30 Min. 1 15 50 Standard Sockets (Eccentric Floor Socket) 2 1 2 " 64 Optional Dustproof Floor Socket PrivaSEE SHEET 10 OF 13
Panel Installation for non-entry Single Action Offset End Panel and Single Action End Panel with Floor Closer Set screw to secure axle from turning Panel-Height adjustment Height adjustment screws inside floor closer 2 5 8 " 66 PrivaSEE SHEET 11 OF 13
Field Applying Vertical H- and h-gaskets and Height Adjustment of ottom Compression Seal Please cut to size the vertical clear gaskets in the field; top and bottom should line up with the top and bottom edge of the end cover. H-gasket (between sliding panels) and h-gasket (on the side of the sliding panel meeting the single action end panel with offset hinge) PrivaSEE SHEET 12 OF 13
Installation of Mortise Cylinder (on Inside only) allen wrench for set screw Mortise Cylinder on inside only PrivaSEE SHEET 13 OF 13