1326 LINCOLN AVENUE HOLLAND MI 49423 (616) 396-4678 (800) 527-8818 FAX: (616) 396-9543 sales@hollandsupplyinc.com www.hollandsupplyinc.com Dear Valued Customer, Thank you for purchasing the 14 x 20 CHAPEL TENT. This unit, when assembled properly, will provide years of service with very little maintenance. It is vital to remember that the unit should never be towed without the stringers and tow bar assembly in place. Also, remember to tighten the hardware periodically. We have included assembly instructions to assure a solid and safe structure. Thanks again for purchasing from Holland Supply. We greatly appreciate your business. If you have any questions about this tent or are interested in any other products, please don t hesitate to call us at 800-527-8818, or visit our website at www.hollandsupplyinc.com Sincerely, Holland Supply, Inc.
14 x 20 CHAPEL TENT ASSEMBLY INSTRUCTIONS Please read completely through instructions before starting assembly 1. Lay out the (8) 10 beams so you can connect the centers together in order to create (4) beams 20 in length. The (4) 10 beams with the angle on, will be connected together (angle on top side, facing toward perimeter), to make the (2) INSIDE, 20 beams. The (4) 10 beams without the angle will be connected together, to make the (2) perimeter 20 beams. Use the ⅜ x 1 HEX HEAD BOLTS to connect the beams. 2. Use ⅜ x 2½ HEX HEAD BOLTS to attach the 30 long connector bars to the bottom side of the (4) 20 beams for reinforcement in the center. There will be 4 holes for each connector bar, 2 on each side of the center. 3. Use ⅜ x 1 HEX HEAD BOLTS to connect the (4) 7 end pieces into (2) 14 ends. Make sure the 7 end pieces match before assembling. Use ⅜ x 2½ HEX HEAD BOLTS to attach (1) 30 CONNECTOR BAR to the bottom side of each 14 end to add extra reinforcement in the center. There will be holes for each CONNECTOR BAR, 2 on each side of center. 4. Use ⅜ x 2½ HEX HEAD BOLTS to connect the 20 beams to the 14 end pieces. Note: the beams with the angle will be in the center and the angle will be pointed toward the outside so the 6 fiberglass panels will lay on it. The top should now be completely assembled. 5. It is easier to put the fiberglass panels on next, while the top frame is still on the ground. Make sure the frame is on a level (flat) area and square as possible. 6. Lay out the 6 fiberglass panels down each 20 side, with an approximate 2 groove overlap. Then drill pilot holes through the panels and attach to frame with the roof screws. Next, put the 4 fiberglass panels across the top using the same method. 7. Raise up one end and install the (2) corners, using the Use ⅜ x 2½ HEX HEAD BOLTS. Keep the end flat to ensure no pressure is put on the fiberglass panels. 8. Raise up the other end and install the other (2) corners. 9. Lastly, one side at a time, attach the 14 wheels using the ½ x 1½ CARRIAGE BOLTS, NUTS and LOCK WASHERS. Note: Use (2) WASHERS per ⅜ HEX HEAD BOLT. Put flat washer next to head and lock washer next to nut. All holes should line up well enough to insert bolts and attach frame pieces. If the hole is not lined up and the bolt will not fit through, please use a ½ bit and drill to clean up the hole and allow the bolt to slide through. -This will not jeopardize the overall strength of the Chapel Tent. Thanks again for your business. Please call our Customer Service Team with any questions 800-527-8818
14 X 20 CHAPEL TENT 10 TRUSS (NO ANGLE) ON OUTSIDE 10 TRUSSES WITH ANGLE ON ROOF WILL LAY ON ANGLE IRON 10 TRUSS (NO ANGLE) ON OUTSIDE END VIEW - 14 SIDE 10 TRUSS 10 TRUSS MOUNT ON BOTTOM SIDE SIDE VIEW OF 20 SIDE 11/06/2013
PARTS LISTS 14 x 20 CHAPEL TENT 4 - CORNERS 4-10 BEAMS WITH ANGLE 4-10 BEAMS W/O ANGLE 4-7 END PIECES 6-30 CONNECTOR BARS 4-12 OR 14 WHEELS 11-4 X 26 FIBERGLASS PANELS 22-6 X 26 FIBERGLASS PANELS 1 BOLT KIT 16 ½ X 1½ CARRIAGE BOLTS 16 ½ LOCK WASHERS 16 ½ NUTS 64 ⅜ x 2½ HEX HEAD BOLTS 32 ⅜ x 1 HEX HEAD BOLTS 96 ⅜ NUTS 96 ⅜ LOCKWASHERS 96 ⅜ WASHERS 200 SELF TAPPING ROOF SCREWS TOWBAR 1 - FRONT CROSSBAR WITH EARS 2 - FRONT CROSSBAR ENDS 4 - SIDEBAR END Ts 2 - SIDEBAR CONNECTORS 2 - FRONT TOWBAR ANGLE WITH PIN & CHAIN 1 - FRONT TOWBAR ANGLE IRON 1 - FRONT TOW PLATE 1 - BOLT KIT: 12 - ⅜ x 2½ HEX HEAD BOLTS 13 - ⅜ LOCKWASHERS 13 - ⅜ NUTS 1 - ⅜ x 1 HEX HEAD BOLT
CHAPEL TENT ROOF REINFORCEMENT KIT Qty Item 2 118¼ x 1⅜ GALVANIZED STEEL TUBING WITH SWEDGED END 2 118¼ x 1⅜ GALVANIZED STEEL TUBING WITHOUT SWEDGED END 2 34 x 1⅜ GALVANIZED STEEL TUBING WITH SWEDGED END. 2 34 x 1⅜ GALVANIZED STEEL TUBING WITHOUT SWEDGED END 4 ⅜ x 1 HEX HEAD BOLTS 4 ⅜ x 1½ HEX HEAD BOLTS 4 ⅜ x 2½ HEX HEAD BOLTS 16 ⅜ LOCK WASHERS 16 ⅜ NUTS 50 SELF-TAPPING SCREWS WITH RUBBER WASHERS 2 PLASTIC TIES Adding to an existing Chapel Tent... Begin with the 34 pieces. These wills serve as a cross beam for the (2) 118¼ pieces. Take (2) 34 pieces (one with swedged end and one without) and slide them together. This 65 cross beam can be bolted (using the existing bolts or the 1½ bolts supplied) between the current 10 beam sections -use the top bolt. Now, slide (2) 118¼ pieces together (one with the swedged end and one without), place over the 65 cross beam and bolt to the tabs on each 14 end using the 1 bolts. Use plastic ties to secure beams at point of intersection, so they won t slide around. If desired, 50 self-tapping screws with rubber washers are included to secure the fiberglass top to the new support beams. - This will keep the fiberglass from rattling against the beams when windy. Please call our Customer Service Team with any questions (800-527-8818). Thanks for your business.
CHAPEL TENT TOWBAR ASSEMBLY INSTRUCTIONS SIDE BAR ASSEMBLED 1¾ x 94¼ CONNECTOR FRONT TOWBAR ASSEMBLED EARS FWD ENDS DOWN 1. ASSEMBLE THE 2 SIDEBARS WITH THE 1¾ SLEEVE (DIAGRAM) 2. ASSEMBLE THE FRONT TOWBAR WITH THE ENDS FACING DOWNWARD AND THE EARS THAT CONNECT TO THE TOW PART FACE FORWARD 3. LAY THE FRONT SECTION OUT AND BOLT AS SHOWN NOTE: THE SIDEBARS WILL ALWAYS FASTEN TO THE CORNERS FIRST AND THE FRONT TOWBAR SECTION WILL SLIDE OVER THE SIDES WHEN ATTACHED TO THE TENT CORNERS.
TOW BAR PARTS LIST (14 X 20 CHAPEL TENT) 1CTCBE (1) CHAPEL TENT FRONT CROSSBAR W/ EARS 1¾ sq. x 94¼ long 2CTFCE (2) CHAPEL TENT FRONT CROSSBAR ENDS 1½ sq. x 54½ long with 3¾ end piece 3¾ 4CTS (4) CHAPEL TENT SIDEBAR 1½ sq. x 88½ long with 1¼ sq x 9 end piece 9 2CTSC (2) CHAPEL TENT SIDEBAR CONNECTORS 1¾ sq. x 94¼ long 2CTTA (2) CHAPEL TENT TOWBAR ANGLE 1½ sq. x 70¼ long with 3 end piece w/ pin & chain 3 1CTA1 (1) CHAPEL TENT ANGLE IRON 23½ long 1CTTP (1) CHAPEL TENT TOWBAR PLATE 34 long x 4 wide BOLT KIT: 12 - ⅜ x 2½ HEX HEAD BOLTS 13 - ⅜ LOCKWASHERS 13 - ⅜ NUTS 1 - ⅜ x 1 HEX HEAD BOLT 2013
Did you know that Holland Supply is the leading Manufacturer and Distributor of Burial Vault, Cemetery and Funeral Equipment in the United States? Thanks to all of our customers, we can offer more competitively priced, quality products than anyone else. Holland Supply, Inc. MANUFACTURES 15 x 15 and 15 x 20 Hillside Tops and Frames (manufactured of galvanized steel, aluminum or stainless steel), Walls, Slant Mounds, Sun Extension Tops and Frames, Portable Frames (15 x 15 and 14 x 20 ) with Fiberglass or Sunbrella tops. All sizes of Oval (Steril) tops and aluminum Frames. Graveside Grass, Lowering Device Stands, Chair Covers, Device Straps, Hand Straps, Crypt drapes, Chair Bags, Dump Trailers, Lot Markers, Casket Roller Bars, Cremation Stands, Urn Vaults, Heavy Duty Rammer Probes, and more Holland Supply, Inc. DISTRIBUTES Frigid Lowering Devices, D2 Solution (for cleaning monuments), Folding Chairs, Vases, Mausoleum Lifts, Lawn boards, Flags and Flag Poles, Church Trucks, Casket Carts, Mortuary Cots, Mausoleum Trays, Slings, Trash Containers, Cemetery Signs, Umbrellas, Cremation Supplies and Chapel/ Funeral Equipment We GUARANTEE we will outperform our competition! Customer Service Quality Products Best Value in the industry One call does it all! If you can t find the product on our website or in our catalog, Holland Supply can assist you in finding the products you need. We pride ourselves in offering the best priced, quality products. Thanks again for your business! (800) 527-8818 www.hollandsupplyinc.com