Instant Shed - Peak Style 8' x 8' x 8' Assembly Instructions C A B SCRIPTION MOL # A B C CIS 88 Instant Shed. x. x. M - Green 3503506 8' x 8' x 8' RCOMMN TOOLS OR Please read instructions COMPLTLY before assembly. This shelter MUST be securely anchored. Before you start: or more individuals recommended for assembly, approximate time hours. Clarke International Hemnall Street pping ssex CM16 LG NGLAN www.clarkeinternational.com //1 Page 1 PARTS & SRVIC: 008 988 700 -mail: Parts@clarkeinternational.com or Service@clarkeinternational.com SALS: UK 0199 565333 or XPORT: 00 (0)199 565335
ATTNTION: This shelter product is manufactured with quality materials. It is designed to fit the custom fabric cover included. Please anchor the shed carefully following the instructions in this manual. Proper anchoring, keeping cover tight and free of snow and debris is the responsibility of the consumer. Please read and understand the installation detail, warnings and cautions prior to beginning installation. ANGR: Choose the location of your shed carefully. anger: Keep away from electrical wires. Check for overhead utility lines, tree branches or other structures. Check for underground pipes or wires before you dig. O NOT install near roof lines or other structures that could shed snow, ice or excessive run off onto your shelter. O NOT hang objects from the roof or support cables. WARNING: Risk of fire. o not smoke or use open flame devices (including grills, fire pits, deep fryers, smokers or lanterns) in or around the shed. O NOT store flammable liquids (gasoline, kerosene, propane, etc.) in or around your shed. o not expose top or sides of the shed to open fire or other flame source. CAUTION: Use CAUTION when erecting the frame. PROPR ANCHORING AN INSTALLATION O RAM: PROPR ANCHORING O TH RAM IS TH RSPONSIBILITY O TH CONSUMR. Clarke International is not responsible for damage to the unit or the contents from acts of nature. Any shed that is not anchored securely has the potential to fly away causing damage. Periodically check the anchors to ensure stability of the shed. Clarke International cannot be responsible for any shed that blows away. NOT: Your shed s cover can be quickly removed and stored prior to severe weather conditions. If strong winds or severe weather is forecast in your area, we recommend removal of cover. CAR AN CLANING: A tight cover ensures longer life and performance. Always maintain a tight cover. Loose fabric can accelerate deterioration of cover fabric. Immediately remove any accumulated snow or ice from the roof structure with a broom, mop or other soft-sided instrument. Use extreme caution when removing snow from cover- always remove from outside the structure. O NOT use hard-edged tools or instruments like rakes or shovels to remove snow. This could result in punctures to the cover. O NOT use bleach or harsh abrasive products to clean the fabric cover. is easily cleaned with mild soap and water. Page
Instant Shed 8' x 8' x 8' - Parts List - Model # CIS 88 3503506 escription of Parts: Leg Poles 30 5 /8 in. / 77,8 cm Quantity Part # 6 800598 Leg Poles 0 1 / in. / 10,8 cm 6 8039 Leg Poles 38 1 / in. / 97,1 cm 80308 Rafter Poles 7 11 /16 in. / 70,3 cm 8038 Cross s 1 in. / 53,6 cm 80193 Cross s, Swedged 5 3 / in. / 65, cm 8 Cross s 1 / in. / 6, cm 800703 s 1 / in. / 61,6 cm 1335 s 1 / in. / 61,6 cm 133 Corner Leg Bends 80637 Side Corners 6 8010 3-Way Top Connectors 8017 -Way Top Connector 1 80177 Steel oot Plate 170 Shelter Stabiliser 6 Ratchet Clamp 8 100 Bolts 1 / x 1 5 /8 in. / 6, x 1,3 mm 6 Bolts 1 / x 1 7 /8 in. / 6, x 7,6 mm Bolts 1 / x in. / 6, x 50,8 mm 6 1011 Washer 1 / in. / 6, mm 8 Nut 1 / in. / 6, mm 5 White Bungee Cords (or holding door open) Half-Clamps for Middle Legs Half-Clamps for Corner Legs -Zipper oor Back Panel 15 in. Auger Anchors (Temporary) Cable - 1 ft. Length Cable Clamps 8 1 1 1 10066 1301 130 803073 803075 80307 1001 } 10015 0087 10016 NOT: 15 inch anchors are available from our spare parts department. Please quote Part No. 1001 Page 3
1. Assemble nd RibS Secure connections using Bolts as shown with # Nuts. 800598 8017 800598 8010 8010 # Bolts (1 7 / 8 ") 8010 8039 8039 8039 8038 # Bolts (1 5 / 8 ") 8038 80637 80637. Assemble middle Rib 80177 NOT: The bolt heads at the end ribs must be facing outward to avoid damaging your cover. 800598 800598 8010 # Bolts (1 7 / 8 ") 8010 8039 8039 80308 # Bolts (1 5 / 8 ") 80308 170 170 Page
3. CONNCT RONT N RIB TO MIL RIB A. Assemble Side Cross s using parts as shown. B. Assemble 1 Top Cross using parts as shown. C. Assemble s using parts as shown. Connect the Side Cross s at the Shelter Stabilisers.. Connect the Top Cross at the 3- and -Way Connectors as shown.. Place a at each leg and secure it with a Clamp as shown. Slide the s so they are 8 inches up from the ground. Only HAN-TIGHTN these bolts! Assemble Side Cross s a Assemble Top Cross B 800703 80193 80177 80193 B 80193 800703 a 800703 a Cross 1335 C 133 1335 C 133 nd Rib 130 Assemble s C Middle Rib 1301 1335 133 No Bolt at this connection Page 5
. CONNCT RAR N RIB A. Assemble Side Cross s using parts as shown. B. Assemble 1 Top Cross using parts as shown. C. Assemble s using parts as shown. Connect the Side Cross s at the Shelter Stabilisers.. Connect the Top Cross at the 3- and -Way Connectors as shown.. Place a at each leg and secure it with a Clamp as shown. Slide the s so they are 8 inches up from the ground. Only HAN-TIGHTN these bolts! Assemble Side Cross s a Assemble Top Cross B 80193 80193 80177 nd Rib Cross Middle Rib Cross Assemble s C 1335 133 No Bolt at this connection nd Rib 130 Middle Rib 1301 Page 6
5. Squaring up the rame A. Place frame in its final location, which needs to be as flat and level as possible. B. Measure across opposite corners. These distances must be equal to within 1 inch. C. Check that the front and rear of the frame measures 8 feet in width 8 ft. 8 ft. 6. Properly Anchor the rame A. Anchors must be placed inside shelter at the corners of the shelter. B. Insert a ¾ inch pipe or steel rod, through the eyelet of the auger and screw the anchor into the ground until the eyelet is sticking out of the ground by 1 to inches so it can be anchored to the legs. If ground is too hard, dig a hole with a shovel or post hole tool. Optional: ill with cement. C. Wrap cable provided through the eyelet of the anchor and around the frame as shown below. Secure the cable with the clamps provided. nd Rib Anchors WARNING: Serious injury to persons or property could result if cover is installed and shelter is not anchored and is left unattended. Shelter must be securely anchored before use. Page 7
7. oor PANL and BACK panel installation A. (1) Hold end panel at the top center with white inner surface facing inside of the shelter. () Wrap the edges of the fabric panel around the end rib and line up the cross rails with the pre made slits in the fabric. A1 A B. (1) isconnect top cross rail (the horizontal pipe that runs from front to back along the top) from the end rib. () Pull the end panel over the end rib and bring the end of the cross rail through the cut slit in the panel. (3) Reattach the top cross rail to the end rib. B1 B B3 C. (1) isconnect side cross rail from the end rib. Leave the Shelter Stabiliser attached to the rib with the bolt. () Pull the end panel over the end rib and bring the end of the cross rail through the cut slit in the panel. (3) Reattach the side cross rail to the end rib. C1 C C3 Page 8
7. N PANL INSTALLATION - continued. At the bottom, where the webbing exits the pocket on each side of end panel, pull webbing as you would a drawstring to remove the slack. Be careful not to pull the webbing strap out of the webbing pocket. N PANL VIW ROM INSI SH WBBING STRAP PULL PULL. Insert the S - Hook on ratchet into hole on the leg bend. Insert the webbing into the spindle of the ratchet and pull tight. Wind the ratchet so that the webbing overlaps itself. Position the end panel so that it is centered on the building before fully tightening the end panel.. Tighten ratchets, alternating from one side to the other, until the end panel is tight. NOT: Keep zips fastened when tightening door panel. Insert Webbing into Ratchet Page 9
8. INSTALLING COVR AN COVR RAILS A. Lay the cover on the ground next to the frame with inside of the cover (the side with the pipe pockets) facing down and the webbing on the front and rear of the corner of the building. B. Pull cover over the frame, making sure to center cover on frame. There should be an equal amount of overhang at all four corners. C. Insert the S - Hook on ratchet into hole on the leg bend. Insert the webbing into the spindle of the ratchet and pull tight. Wind the ratchet so that the webbing overlaps itself.. isassemble cover rails and slide through fabric pockets at each leg and reattach with clamps to each leg. Repeat this on other side. Push down on cover rails to tighten cover, before tightening bolts completely.. Check and tighten Ratchets and s monthly to ensure the cover is tight. NOT: The Clarke logo should be oriented as shown below. correct INcorrect RAR RONT cover s Webbing and Ratchets Securing nd Rib Cross Clamps Corner Leg 130 Middle Rib Cross Clamps Middle Leg 1301 1335 133 1335 Page 10
other quality leisure & gardening products available from logbusters banqueting tables bbq s portable generators garden trolleys binoculars L headlights / flashlights hot & cold power washers tarpaulins insect killers car covers inverters jump starts foot pumps fans ladders and much more! PARTS & SRVIC: 008 988 700 -mail: Parts@clarkeinternational.com or Service@clarkeinternational.com SALS: UK 0199 565333 or xport: 00 (0)199 565335 Hemnall Street, pping, ssex CM16 LG www.clarkeinternational.com Page 11