IP26 Series Current to Pneumatic Converter

Product Specifications 06.2016 PSS EVE0403 A-(en) IP26 Series Current to Pneumatic Converter The IP26 (current to pressure) transducer converts a 4 20mA electrical current signal to a proportional linear pneumatic output. The unique conversion technology provides a high level of accuracy and repeatability for the operation of actuated valves. A low mass control circuit provides consistent output in high vibration applications. This compact unit is housed in an explosion proof enclosure that is designed for pipe, bracket or direct manifold mounting. This explosion-proof and intrinsically safe field device is available with a built-in volume booster. FEATURES 4 to 20 ma, 2-wire Loop powered Compact design, small size and low weight Approvals Intrinsically Safe and Explosion Proof ATEX, FM and CSA certification Gas and Dust certification Position insensitive Unit can be mounted in any plane and is stable in high vibration environments Low power consumption minimize loop load

2 IP26 PSS EVE0403 A-(en) SPECIFICATIONS Functional Specifications Input Outputs (to be selected in Model Code) 4-20 ma 0.2-1 bar (3-15 psig) 0.1-1.7 bar (1.5-25 psig) 0.4-2 bar (6-30 psig) Outputs with pressure up to 6 bar (90 psi) can be obtained by adding a volume booster with amplifying ratio Please consult us! Air Consumption 2.83 l/min (0.1 scfm) Supply Pressure Note: Supply pressure must be a minimum of 0.3 bar (5 psig) above maximum output 0.2-1 bar: 1.5 bar (22 psig) max 0.1-1.7 bar: 2.8 bar (42 psig) max 0.4-2 bar: 2.8 bar (42 psig) max Flow Capacity 4.1 m 3 /h (2.4 scfm) max. Temperature Limits 40 C to 85 C ( 40 F to 185 F) / down to 55 C ( 67 F) with option -T Relative Humidity 75% average - 95% short time non-condensing Impedance 260 Ohms @ 21 C (70 F) Loop Load 5.2 Volts @ 21 C (70 F) Performance Specifications Linearity (Independent) Hysteresis Deadband Repeatability Mounting Orientation Air Supply Sensitivity Vibration Effect Temperature Effect < ±0.5% of span < ±0.3% of span < ±0.1% of span < ±0.3% of span; < ±0.15% of span typical < ±0.5% / 90 degree change < 0.3% / 1.5 psig (0.10 bar) change < ±1% up to 10 g and 20-80 Hz < ±0.75% / 12 C (/ 10 F) change Physical Specifications Housing IP 65 (NEMA 4X) Port Sizes In/Out Pneumatic: 1/4 NPT; gauge part: 1/8 NPT Electric: M20x1.5 (ATEX) / 1/2 NPT (FM / CSA) Media Clean, dry, oil-free, instrument air, filtered to 40 micron Electrical Connections Terminal block Mounting 2 pipe (optional) Materials Housing: Chromate-treated Aluminum with epoxy paint. IP65 (NEMA 4X) Elastomers: Trim: Label: Buna-N Stainless steel; brass; zinc-plated steel Stainless steel Weight 0.64 kg (1.4 lb)

4 PSS EVE0403 A-(en) IP26 3 HAZARDOUS AREA CLASSIFICATION Cover label: ATEX 1 2 $? H H A F A = E?? L A H A H Cover label: FM / CSA. N > H > O 5? D A E @ -A HA? J H E? 1 2 $? H H A F A = E?? L A H A H ATEX Approvals Intrinsic Safety II 1 G Ex ia IIC Flameproof II 2 G Ex d II B + H2 II 2 D Ex td A21 T85 C Entity Parameters Temperature Code Enclosure Certificate Vmax = 40 Vdc Imax = 150 ma Pi = 0.7 W T* -55 C to Ta max* IP65 FM14ATEX0022 X Ci = 0 nf Li = 0 mh Limited Energy/Non-Sparking T* -55 C to Ta max* II 3 G Ex nl IIC T6-55 C Ta +85 C II 3 G Ex na nl IIC *See energy limiting parameters. Refer to Master Instruction MI EVE0403. Entity Parameters: Ui (Vmax) = 40 VDC Ci = 0 µf Ii (Imax) = 150 ma Li = 0 mh Pi = 0.7 W max. IP26-1a00 and I/P Converter for SRI983: II 3 G Ex nl IIC T* Ta = 55 C to +85 C A = Output Pressure Range: 0, 1, or 2 Energy Limitation Parameters * Temperature Class Ta Ii Ui Pi T4 85 C 60 ma 38.8 V 2.328 W T4 85 C 100 ma 30 V 3.0 W T4 80 C 120 ma 28 V 3.36 W T4 70 C 150 ma 25.5 V 3.825 W T5 70 C 60 ma 38.8 V 2.328 W T5 55 C 100 ma 30 V 3.0 W T5 45 C 120 ma 28 V 3.36 W T5 85 C 23 ma 6.75 V 0.155 W T6 60 C 50 ma 42.5 V 2.125 W T6 55 C 60 ma 38.8 V 2.328 W T6-40 C Ta +75 C IP65 FM14ATEX0022 X IP65 FM14ATEX0023 X

4 IP26 PSS EVE0403 A-(en) FM Approvals (FM) & Canadian Standards Association (CSA) Approvals Intrinsically Safe: Non-Incendive: Class I, Div. 1, Groups A, B, C & D Class I, Div. 2, Groups A, B, C & D Class II, Div. 1, Groups E, F & G Class II, Div. 2, Groups E, F & G Class III, Div. 1, Fibers Class III, Div. 2, Fibers Enclosure Nema 4X (IP65) Enclosure Nema 4X (IP65) Rated 4-20 ma, 40 VDC Max. Temp. Code T6 Temp. Code T4 Ta = + 70 C Entity Parameters: Explosion Proof: Vmax = 40 VDC Ci = 0 µf Class I, Div. 1, Groups A, B, C, D Imax = 150 ma Li = 0 mh Enclosure Nema 4X (IP65) Temp. Code T6 Entity Installation Requirements: Vmax Vt OR Voc Dust Ignition Proof: Imax It OR Isc Class II & III, Div. 1, Groups E, F & G Ca Ci + Ccable Enclosure Nema 4X (IP65) La Li + Lcable Temp. Code T6 Note: Cable capacitance and inductance must be considered when connecting to pressure transducer.

PSS EVE0403 A-(en) IP26 5 INSTALLATION DRAWING NO. 531-990-081 1. (North America) Control equipment connected to the Associated Apparatus must not use or generate more than 250 Vrms or Vdc. 2. (North America) The IS Barriers or Equipment (Associated Apparatus) must be FM Approved and CSA certified and the configuration of associated Apparatus must be FM Approved and CSA certified under the Entity Concept. The Associated Apparatus may be installed within the Hazardous (Classified) location for which it is certified. The Associated Apparatus and hazardous location loop apparatus manufacturer's control drawings must be followed when installing this equipment. An AEx [ib] Associated Apparatus is suitable only for connection to Class I, Zone 1, Hazardous (Classified) Locations and is not suitable for Class I, Zone 0, or Class I, Division 1 Hazardous (Classified) Locations. (ATEX) The IS Barriers or other Associated Apparatus shall comply with the ATEX directive 94/9/EC. 3. (US) Installation should be in accordance with ANSI/ISA RP12.06.01 "Installation of Intrinsically Safe Systems for Hazardous (Classified) Locations" and Article 500 of the National Electrical Code (ANSI/NFPA 70) (Canada) Installation should be in accordance with Section 18 of the Canadian Electrical Code. (ATEX) Installation shall be in accordance with the applicable local installation rules Energy Limitation Parameters specified. 4. (North America) All units suitable for Type 4X installations. 5. (North America) Units are suitable for Class I, Division 2, Groups A, B, C, and D hazardous (classified) locations. Transducers to be installed in accordance with the (US) National Electrical Code (ANSI/NFPA 70) Division 2 hazardous (classified) location wiring techniques (Canada) Canadian Electrical Code. 6. The Intrinsic Safety Entity concept allows the interconnection of two Intrinsically safe devices with entity parameters not specifically examined in combination as a system when: Entity Parameters for: IP26 Ui (Vmax) = 40 V Ii (Imax) = 150 ma Ci=0 Li=0 Pi = 0.7 Watt Ui or Vmax >Uo or Voc Ii or Imax > Io or Isc or It Ca or Co > Ci + Ccable La or Lo > Li Lcable Pi > Po. 7. No revision to this drawing is permitted without prior FM Approval and CSA Certification.

6 IP26 PSS EVE0403 A-(en) MODEL CODES IP26 Electro/pneumatic Signal Converter IP26 - Input Signal 4-20 ma 1 Output Signal (without Output gauge) 0.2-1 bar (3-15 psi) 0 0.1-1.7 bar (1.5-25 psi) 1 0.4-2 bar (6-30 psi) 2 Body Material Aluminium 0 Stainless Steel (not released) 1 Electrical Certification ATEX Intrinsically Safe and Explosion Proof 0 FM & CSA, IS and XP 1 Option Low temperature down to 55 C ( 67 F) -T MODEL CODES ACCESSORIES FOR IP26 2 inch pipe mounting kit (steel zinc plate and clear chromate) EBZG-IP1 Gauge for Output pressure (scale 0-2.5 bar) (stainless steel housing) EBZG-IP2 Pipe for gauge mounting (stainless steel) VG-92 Filter regulator FRS02 (Aluminium Housing) FRS02 Pipe VG-91 (stainless steel) VG-91 Cable Entry 1/2 NPT via adaptor (Brass Nickel coated) AD-A5 Cable Entry 1/2 NPT via adaptor (Stainless steel) AD-A6 EC Declaration of Conformity We, FOXBORO ECKARDT GmbH Pragstr. 82 D-70376 Stuttgart declare that the IP26 Transducer family to which this declaration applies, comply with these standards: EN 50082-1:1998 EN 55011:1999 EN 61010-1:1993 including AMD2:1995 Following the provisions of EMC directive 89/336/EEC EN 60079-0:2006 EN 60079-11:2007 EN 60079-26:2007 EN 60079-1:2007 EN 61241-0:2007 EN 61241-1+Corr.1:2004/2005 EN 60529+A1, A2:1992/2000 EN 60079-15:2005 Following the provisions of EMC directive 94/9/EC

PSS EVE0403 A-(en) IP26 7 DIMENSIONS I/P Converter for use with pneumatic positioner SRP981 / SRI983 %! % ' &! ' & #! " % " "! % $!! '! " "!! ' ' " %! $ 6 ' 0 4 7 7 6 1 / 5 $ 7 2 2 ; 2 4 6 $ $ 7 6 2 4 6 $ # " # " N # +, 7 1 6 2 4 6 E "!! $ " IP26 Series Stand Alone I/P converter %! $ '! # $ &! ' " # % # N # +, 7 1 6 2 4 6 " " 2 6 7 6 2 7 6 2 4 6 ' #! & # # '! % & 2 6 / ) 7 / - 2 4 6 " 2 6 5 7 2 2 ; 2 4 6 $ " $ # Optional 50 mm / 2 Bracket, EBZG-IP1 2 4. 1-5 0 - - 6. 4 9 ) 7 6 1 / " 2 6 7 6 2 4 6 & 2 6 / ) 7 / - 2 4 6 # & & % # $ # % # $ " " & $! " & # # ' $ " 2 6 5 7 2 2 ; 2 4 6 % % # & "!! E & '! # & '! #

8 IP26 PSS EVE0403 A-(en) EXAMPLES FOR MOUNTING 8 / ' 1 2 $ 1 2? L ) E H 7 6 1 ) E I K F F O - * / 1 2 - * / 1 2 1 " ). 4 5. 4 5 - * / 1 2 8 / ' ) E H 7 6 1 ) E I K F F O 8 / ' - * / 1 2 1 2 $ 1 2? L 1 " ) Invensys Systems, Inc. 38 Neponset Avenue Foxboro, MA 02035 United States of America Copyright 2010-2016 Invensys Systems, Inc. All rights reserved. Invensys, Foxboro, and I/A Series are trademarks of Invensys Limited, its subsidiaries, and affiliates. All other trademarks are the property of their respective owners. Global Customer Support Toll free: 1-866-746-6477 Global: 1-508-549-2424 Website: http://support.ips.invensys.com DOKT 558 694 028 FD-PSS-PO-06-EN 541-622-129 0616