F 1
Please review all parts and hardware before disposing of any packaging. Call Customer Service if missing hardware. Do not return to store/retailer. Using a screw that is too long will cause damage. Before beginning assembly, separate each type of screw. Carefully study the screw diagrams below. You may receive extra hardware with your unit. Top supports up to 175 lb, per fixed shelf supports up to 20 lb, per adjustable shelf support up to 15 lb, per drawer supports up to 10 lb. 1. Wood Dowel 6mmx25mm Quantity Of 40 TV/MEDIA CONSOLE 2. Cam Bolt 6.2mmx32mm Quantity Of 34 3. Screw 3mmx12mm Quantity Of 33 4. Cam Lock 15mmx9mm Quantity Of 34 5. Shelf Holder Quantity Of 8 6. Screw Quantity Of 4 7. Door Handle Quantity Of 2 8. Drawer Handle Quantity Of 2 9. Screw 3mmx19mm Quantity Of 8 10. Pin 16mmx10mm Quantity Of 5 11. Screw Quantity Of 4 12. Screw 3mmx14mm Quantity Of 12 13. Magnet Quantity Of 2 Care and Cleaning Instructions: Before using, wipe with a clean, dry cloth. Periodically apply furniture wax to renew the finish. Avoid rubbing or scratching the surface with rough or abrasive objects. Tool required: Phillips screw driver (Not Included) 2
PARTS LIST: NO DESCRIPTION QTY NO DESCRIPTION QTY A Bottom Base 1 K Center Upper Back Panel 1 B Left Center Divider 1 L Center Lower Back Panel 1 C Right Center Divider 1 M Adjustable Shelves 2 D Lower Center Shelf 1 N Left Door Panel 1 E Upper / Middle Center Shelves 2 O Right Door Panel 1 F Drawer Divider 1 P Drawer Front Panel 2 G Left Side Panel 1 Q Drawer Right Panel 2 H Right Side Panel 1 R Drawer Left Panel 2 I Top Panel 1 S Drawer Bottom Panel 2 J Left/Right Back Panel 2 T Drawer Back Panel 2 CAM LOCK INSTRUCTION PANEL I CAM LOCK CAM LOCK INSTRUCTION: THIS ITEM IS ASSEMBLED WITH CAM LOCK SET. --SCREW CAM BOLT INTO PANEL II. --INSERT CAM LOCK INTO PRE-DRILLED HOLE IN PANEL I, AND --ROTATE CAM LOCK UNTIL ARROW IS IN LINE WITH HOLE ON PANEL EDGE. --ALIGN CAM BOLT TO CAM LOCK HOLE ON PANEL I, AND PRESS PANELS I & II TOGETHER. --LOCK PANELS TOGETHER BY TURNING CAM LOCK CLOCKWISE UNTIL TIGHT. PANEL II CAM BOLT LOCK DOWEL NOTE : FOLLOW INSTRUCTIONS LISTED BELOW IN THE PROPER SEQUENCE AS NUMBERED TO ASSURE FAST, EASY AND CORRECT ASSEMBLY. HOUSE HOLD GLUE SUGGESTED FOR WOOD DOWEL.(eg. ELMERS GLUE, NOT PROVIDED).SOLID ARROW MARK POINTS AT FRONT SIDE OR UP DIRECTION. PHILLIP SCREW DRIVER IS REQUIRED(NOT PROVIDED).TWO PERSONS ARE RECOMMENDED TO ASSEMBLE THIS ITEM. 3
Screw Cam Bolts (2) into Bottom Base (A) as shown. A Step 2: C Screw Cam Bolts (2) into Left Center Divider (B), Right Center Divider (C) and Lower Center Shelf (D) as shown. B D Figure 1 4
C B E E D H Attach Upper and Middle Ce nter Shel ve s (E) a nd Lower Center Shelf (D) to Left Center Divider (B) and Right Center Divider (C) by inserting Wood Dowers (1) and Cam Bolts (2) into their corresponding holes until panels meet. I nsert and t ight en Cam Locks (4) with Philips Screw Driver. Attach Drawer Divider (F) and Secure with Cam Locks (4). G Figure 2 B Step 2: Attac h Left S ide Panel (G), Right Side Panel (H), and the assembled unit from Step 1 to the Bottom Base (A) by inserting Wood Dowels (1) and Cam Bolts (2) into their corresponding holes until all panels meet. I nsert and t ight en Cam Locks (4). 5
I Screw Cam Bolts (2) into the threaded inserts on the bottom of Top Panel (I). Step 2: Install Magnets (13) to the Top Panel (I) using Screws (12) as shown. I Step 3: B C Attach the Top Panel (I) to the assembled unit by H inserting Wood Dowels (1) and Cam Bolts (2) into their corresponding holes until all panels meet. Insert and tighten Cam Locks (4). G N o t e : M a k e s u r e t h e Magnets (13) are facing the front. Figure 3 6
K J J and Pins (10). L Attach the Left Back Panel ( J ), Center Upper Back Panel (K), Cent er Lower Back Panel (L) and Right Back Panel (J) to the back of the unit using Screws (3) Note : Pins (10) are ONLY used to attach the center of the panels. Step 2: M Insert the Shelf Holders (5) into the desired pre-drilled holes on Side Panels (G/H) and Center Dividers (B/C). M Step 3: Place Adjustable Shelves (M) onto the Shelf Holders(5) as shown. Figure 4 7
O Attach the Door Handles (7) to Left Door Panel (N) and Right Door P anel ( O ) us ing S c rews (6) on shown. Step 2: Attach Door Panels (N/O) to Side Panels (G/H) using Screws (12) into the pre-drilled holes. N P Figure 5 Step 3: Attach Drawer Handles (8) to Drawer Front Panel (P) with Screws (11), screw Cam Bolts (2) into Drawer Front Panel (P). Step 4: Assemble Drawer Front Panel (P), Drawer Left Panel (R) and Drawer Right Panel (Q) by inserting Wood Dowels (1) and Cam Bolts (2) into their corresponding holes until the panels meet. Insert and tighten Cam Locks (4). I nser t Drawer Bottom Panel (S) into the grooves of the drawer panels. Step 5: A t t ach t he Dr awer B ac k P anel (T) to the drawer assembly using Screws (9) as shown. Repeat step 3-5 to assemble the second drawer. 8
Insert the drawers onto the drawer glides. Figure 6 9
CAUTION The top shelf is intended for a flat screen television with a maximum overall width of 45 and supports up to 175 lb. The top shelf is NOT INTENDED for tube televisions. Each fixed shelf should not be loaded with more than 20 lb. Each adjustable shelf should not be loaded with more than 15lb. Each drawer should not be loaded with more than 10 lb. DO NOT EXCEED RECOMMENDED LOAD. Use with products heavier than the maximum sizes and weights indicated may result in instability causing possible injury. This unit contains a permanent warning sticker located on back panel. Do not allow children under 16 years to move the cart. 10
Parts Replacement Form Customer Information Name Address City/State/Zip Code Phone Number Please indicate where you purchased this item: Store/Website/Catalog Please indicate color/size/style number: Style No Parts Letter Parts Description Quantity Needed Please immediately examine this product carefully. Please contact the retailer that you purchased from for returns. 11