Dual Single-Pole OptoMOS Relays Normally Open & Normally Closed Parameter Rating Units Load Voltage 6 V Load Current 1 A rms / A DC On-Resistance (max).4 Features 37V rms Input/Output Isolation Low Drive Power Requirements (TTL/CMOS Compatible) Arc-Free With No Snubbing Circuits No EMI/RFI Generation Small 8-Pin Package Machine Insertable, Wave Solderable Surface Mount Version Tape & Reel available Applications Telecommunications Instrumentation Multiplexers Data Acquisition Electronic Switching I/O Subsystems Utility Meters (gas, oil, electric and water) Medical Equipment-Patient/Equipment Isolation Security Aerospace Industrial Controls Description is a 6V, 1A,.4 dual Solid State Relay integrating independent normally open (1-) and normally closed (1-) relays into a single package. It features a superior combination of low on-resistance and enhanced peak load current (A max.) handling capability. Approvals UL Recognized Component: File # E7627 CSA Certified Component: Certificate # 117739 EN/IEC 69-1 Certified Component TUV Certificate B 9 7 4941 4 Ordering Information Part # S STR Description 8-Pin DIP (/Tube) 8-Pin Surface Mount (/Tube) 8-Pin Surface Mount (1/Reel) Switching Characteristics of Normally Open Devices 9% I LOAD 1% t on t off Pin Configuration 1 + Control - Normally Closed 2 Control - Normally Closed 3 + Control - Normally Open 4 Control - Normally Open 8 7 6 Normally Closed Normally Open Switching Characteristics of Normally Closed Devices I LOAD 9% 1% t off t on Pb e3 DS--R3 www.ixysic.com 1
Absolute Maximum Ratings @ 2ºC Parameter Ratings Units Blocking Voltage 6 V P Reverse Input Voltage V Input Control Current ma Peak (1ms) 1 A Input Power Dissipation 1 1 mw Total Power Dissipation 2 8 mw Isolation Voltage, Input to Output 37 V rms Operational Temperature -4 to +8 C Storage Temperature -4 to +12 C 1 Derate linearly 1.33 mw / ºC 2 Derate linearly 6.67 mw / ºC Absolute Maximum Ratings are stress ratings. Stresses in excess of these ratings can cause permanent damage to the device. Functional operation of the device at conditions beyond those indicated in the operational sections of this data sheet is not implied. Electrical Characteristics @ 2ºC Parameter Conditions Symbol Min Typ Max Units Characteristics: (Normally Open) Load Current Continuous - I L - - 1 A rms / A DC Peak t < 1ms I LPK - - ± A P On-Resistance I L =1A R ON -.21.4 Off-State Leakage Current V L =6V I LEAK - - 1 A Output Capacitance V, f=1mhz C OUT - 1 - pf Switching Speeds Turn-On t =ma, V L =1V on -.7 Turn-Off t off -.9 ms Input Control Current to Activate I L =1A - - 2 ma Input Control Current to Deactivate -.1 - - ma Characteristics: (Normally Closed) Load Current Continuous - I L - -. A rms / A DC Peak t < 1ms I LPK - - ±1.2 A P On-Resistance I L =.A R ON - 1.63 2 Off-State Leakage Current V L =6V, =ma I LEAK - - 1 A Output Capacitance =ma, V, f=1mhz C OUT - 28 - pf Switching Speeds Turn-On t =ma, V L =1V on -.8 Turn-Off t off -.76 ms Input Control Current to Activate - - - 2 ma Input Control Current to Deactivate I L =.A.1 - - ma Common Characteristics: and Input Voltage Drop =ma V F.9 1.2 1.4 V Reverse Input Current V R =V I R - - 1 A Capacitance, Input to Output - C I/O - 3 - pf *NOTE: If both poles operate simultaneously, then load current must be derated so as not to exceed the package power dissipation value. R3 2 www.ixysic.com
RELAY PERFORMANCE DATA @2ºC (Unless Otherwise Noted)* 3 Typical LED Forward Voltage Drop (N=, =ma) 2 (N=, =ma, I L =1mA) 2 (N=, =ma, I L =1mA) 2 2 1 1 2 1 1 1 1 1.22 1.22 1.23 1.23 1.24 1.24 LED Forward Voltage Drop (V).7.61.6.69.73.77 Turn-On Time (ms).77.82.87.92.97.12 Turn-Off Time (ms) 2 Typical for Switch Operation (N=, I L =2mA) 2 Typical On-Resistance (N=, =ma, I L =1A) 2 Typical Blocking Voltage (N=) 1 1 2 1 1 1 1.6.69.73.77.81.8.26.27.28.29.21.211 On-Resistance ( ) 6. 66. 66. 67. 67. 68. Blocking Voltage (V P ) LED Current (ma) Turn-On Time (ms).9.9.8.8.7 Typical for Switch Operation =2mA).7-4 -2 2 4 6 8 1 2. 2. 1. 1. =1mA) =2mA =ma. -4-2 2 4 6 8 1 Turn-On Time ( s) Turn-Off Time ( s) 12 1 8 6 4 2 9 8 8 7 7 6 6 vs. LED Forward Current =1mA) 1 2 3 4 =1mA) =ma =2mA -4-2 2 4 6 8 1 Turn-Off Time ( s) AC On-Resistance ( ) 77.8 77.7 77.6 77. 77.4 77.3 77.2 77.1.26.24.22.2.18.16.14 vs. LED Forward Current =1mA) 1 2 3 4 Typical On-Resistance (AC) =ma, =ma).12-4 -2 2 4 6 8 1 *The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application department. R3 www.ixysic.com 3
Current (A) Typical Load Current vs. Load Voltage ( =ma) 1... -. RELAY PERFORMANCE DATA @2ºC (Unless Otherwise Noted)* -1. -.2 -.1 -.1 -....1.1.2 Voltage (V) 2 Load Current (A) Maximum Load Current ( =ma) 1.2 1..8.6.4.2 Typical Leakage Measured Across Pins & 6 (V L =6V). -4-2 2 4 6 8 1 6 Blocking Voltage (V P ) Energy Rating Curve Typical Blocking Voltage 7 69 68 67 66 6 64 63 62-4 -2 2 4 6 8 1 Leakage Current (na) 1 1 Load Current (A) 4 3 2 1-4 -2 2 4 6 8 1 1 s 1 s 1ms 1ms 1ms 1s 1s 1s Time RELAY PERFORMANCE DATA @2ºC (Unless Otherwise Noted)* 3 Typical LED Forward Voltage Drop (N=, =ma) 2 (N=, =ma, I L =1mA) 2 (N=, =ma, I L =1mA) 2 2 1 1 1 1 2 1 1 1.22 1.22 1.23 1.23 1.24 1.24 LED Forward Voltage Drop (V).7.3.3.76.99.622 Turn-On Time (ms).63.67.71.7.79.83 Turn-Off Time (ms) 2 Typical for Switch Operation (N=, I L =2mA) 2 Typical On-Resistance (N=, =ma, I L =ma) 2 Typical Blocking Voltage (N=, =ma) 2 1 1 1 1 1 1.16.17.18.19.2.21 1.49 1.3 1.7 1.61 1.6 1.69 On-Resistance ( ) 7 76 77 78 79 8 Blocking Voltage (V P ) *The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application department. R3 4 www.ixysic.com
.4 RELAY PERFORMANCE DATA @2ºC (Unless Otherwise Noted)* Typical for Switch Operation =1mA) 423 vs. LED Forward Current =1mA) 2. vs. LED Forward Current =1mA) LED Current (ma).3.3.2.2.1 Turn-On Time ( s) 422 421 42 419 418 Turn-Off Time (ms) 2. 1. 1...1-4 -2 2 4 6 8 1 417 1 2 3 4 1 2 3 4 LED Forward Current (ma) Turn-On Time ( s) 8 7 6 4 3 2 =1mA) =2mA =ma 1-4 -2 2 4 6 8 1 Turn-Off Time (ms) =1mA) 4. 4. 3. I 3. F =2mA 2. 2. 1. =ma 1.. -4-2 2 4 6 8 1 On-Resistance ( ) Typical On-Resistance ( =ma, I L =1mA) 1.8 1.7 1.6 1. 1.4 1.3 1.2 1.1-4 -2 2 4 6 8 1.6 Typical Load Voltage vs. Load Current ( =ma).6 Maximum Load Current ( =ma) 94 Typical Blocking Voltage ( =ma) Current (A).4.2. -.2 -.4 Load Current (A)..4.3.2.1 Blocking Voltage (V P ) 92 9 88 86 84 82 -.6-1. -.8 -. -.3..3..8 1. Voltage (V). -4-2 2 4 6 8 1 8-4 -2 2 4 6 8 1 *The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application department. R3 Leakage Current (na) 3 3 2 2 1 1 Typical Leakage vs.temperature Measured Across Pins 7&8 ( =ma, V L =6V) -4-2 2 4 6 8 1 Load Current (A) 1. 1.3 1.1.9.7. Energy Rating Curve.3 1 s 1 s 1ms 1ms 1ms 1s 1s 1s Time www.ixysic.com
Manufacturing Information Moisture Sensitivity All plastic encapsulated semiconductor packages are susceptible to moisture ingression. IXYS Integrated Circuits Division classified all of its plastic encapsulated devices for moisture sensitivity according to the latest version of the joint industry standard, IPC/JEDEC J-STD-2, in force at the time of product evaluation. We test all of our products to the maximum conditions set forth in the standard, and guarantee proper operation of our devices when handled according to the limitations and information in that standard as well as to any limitations set forth in the information or standards referenced below. Failure to adhere to the warnings or limitations as established by the listed specifications could result in reduced product performance, reduction of operable life, and/or reduction of overall reliability. This product carries a Moisture Sensitivity Level (MSL) rating as shown below, and should be handled according to the requirements of the latest version of the joint industry standard IPC/JEDEC J-STD-33. Device Moisture Sensitivity Level (MSL) Rating / S MSL 1 ESD Sensitivity This product is ESD Sensitive, and should be handled according to the industry standard JESD-62. Reflow Profile This product has a maximum body temperature and time rating as shown below. All other guidelines of J-STD-2 must be observed. Device / S Maximum Temperature x Time 2ºC for 3 seconds Board Wash IXYS Integrated Circuits Division recommends the use of no-clean flux formulations. However, board washing to remove flux residue is acceptable. Since IXYS Integrated Circuits Division employs the use of silicone coating as an optical waveguide in many of its optically isolated products, the use of a short drying bake could be necessary if a wash is used after solder reflow processes. Chlorine- or Fluorine-based solvents or fluxes should not be used. Cleaning methods that employ ultrasonic energy should not be used. Pb e3 R3 6 www.ixysic.com
2.4 ±.127 (.1 ±.) 6.3 ±.127 (.2 ±.) Pin 1.47 ±.76 (.18 ±.3) 4.64 TYP (.16) 9.62 ±.381 (.38 ±.1) Mechanical Dimensions 3.32 ±.1 (.13 ±.2) 7.62 ±.24 (.3 ±.1) 9.144 ±.8 (.36 ±.2) 7.239 TYP. (.28).24 ±.127 (.1 ±.) 8-.8 DIA. (8-.31 DIA.) 6.3 ±.127 (.2 ±.) 7.62 ±.127 (.3 ±.) PCB Hole Pattern 2.4 ±.127 (.1 ±.) 7.62 ±.127 (.3 ±.).813 ±.12 (.32 ±.4) Dimensions mm (inches) S 2.4 ±.127 (.1 ±.) 9.62 ±.381 (.38 ±.1) 3.32 ±.1 (.13 ±.2).63 ±.127 (.2 ±.) PCB Land Pattern 2.4 (.1) 6.3 ±.127 (.2 ±.) Pin 1 4.44 ±.127 (.17 ±.) 9.2 ±.24 (.37 ±.1).47 ±.76 (.18 ±.3) 7.62 ±.24 (.3 ±.1).24 ±.127 (.1 ±.) 1.6 (.649).6 (.2) 8.9 (.33).813 ±.12 (.32 ±.4) Dimensions mm (inches) R3 www.ixysic.com 7
STR Tape & Reel 33.2 DIA. (13. DIA.) Top Cover Tape Thickness.12 MAX. (.4 MAX.) Bo=1.3 (.46) W=16. (.63) Embossed Carrier Embossment K =4.9 (.193) K 1 =4.2 (.16) Ao=1.3 (.46) P=12. (.472) User Direction of Feed Dimensions mm (inches) NOTES: 1. Dimensions carry tolerances of EIA Standard 481-2 2. Tape complies with all Notes for constant dimensions listed on page of EIA-481-2 For additional information please visit our website at: www.ixysic.com IXYS Integrated Circuits Division makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any time without notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as set forth in IXYS Integrated Circuits Division s Standard Terms and Conditions of Sale, IXYS Integrated Circuits Division assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right. The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other applications intended to support or sustain life, or where malfunction of IXYS Integrated Circuits Division s product may result in direct physical harm, injury, or death to a person or severe property or environmental damage. IXYS Integrated Circuits Division reserves the right to discontinue or make changes to its products at any time without notice. 8 Specification: DS--R3 Copyright 212, IXYS Integrated Circuits Division OptoMOS is a registered trademark of IXYS Integrated Circuits Division All rights reserved. Printed in USA. 12/22/212