Owner s Manual enetia 10 ft. x 1 ft. Hardtop Gazebo endor Code: 999-313663 Product Code: 71 M8091 UPC Code: 7783013663 ate of purchase: / /
Table of Contents Safety Information... Warranty...3 What is Covered...3 What is Not Covered...3 Operation...3 Maintenance...3 Care and Cleaning...3 Pre-installation... Planning Installation... Tools required... Hardware Included...5 Package contents...6 Installation... 7-3 Safety Information WARNING: KP ALL FLAM AN HAT SOURCS AWAY FROM THIS TNT FABRIC. This tent meets the flammability requirements of CPAI-8. The fabric may burn if left in continuous contact with any flame source. The application of any foreign substance to the tent fabric may render the flame-resistant properties ineffective. It is very important to read and follow the safety precautions before assembly and during the use of the product. 1. Keep all children and pets away from assembly area.. When assembling and using this product, basic safety precautions must always be followed to reduce risk of personal injury and damage to product or surroundings. 3. Make sure that all the parts are in the box before starting the assembly. Some parts may contain sharp edges, wear protective gloves.. This unit will take at least 5 hours to set up. You must schedule enough time to complete the assembly. You cannot leave it unattended if not fully assembled, even if bolted to the ground. At least 3 people are required for safe assembly. 5. Begin assembly no less than 6 feet from any obstruction including but not limited to a fence, garage, house,overhanging branches, laundry line or electrical wires. 6. Always install your unit on a level platform. The unit must be anchored to either wood or concrete using the appropriate screws for that flooring. 7. Check all screws for tightness before and during usage. 8. Your shelter has been created for all four seasons and will resist to snow accumulations of 000 lbs. However, you must remove any snow accumulation on the roof. The mosquito nets must also be removed for winter storage. 9. o not place any type of heat conductor under the sun shelter or within 5 feet of the unit including but not limited to a barbeque or space heater.
Warranty WHAT IS COR The enetia sunshelter is guaranteed against defective materials based on normal use of the product as follows: 3 years on the frame and it s finish, years on the roof panels. Limited warranty applicable on parts only. WHAT IS NOT COR amages due to vandalism, abuse or wrong use of the product. amages due to extreme weather conditions such as a thunderstorm, windstorm and hailstorm. Rust, water infiltration, holes in polycarbonate roof panels, fabric and structure discoloration are not covered under warranty. Contact the SOJAG customer service team at 1-866-901-169. Operation The unit is a season sun shelter, meaning it may be left up year round. However, any accumulation of snow must be removed from the roof of the unit. Mosquito netting must be removed for storage during the winter. The unit must be anchored using the appropriate screws based on the flooring which it is be anchored to. Roof panels must be installed with the U protected side facing the sun. Failure to follow any of the previously mentioned requirements will void the warranty. Maintenance If this shelter needs repairs, O NOT RTURN TH PROUCT TO SARS. In case of a defective part or if a problem occurs while using product, please contact SOJAG Customer Service at 1-866-901-169. Use the part number on the parts list to order replacement parts. Care and Cleaning For cleaning: Use a domestic soap or detergent and wash with warm water using a sponge or fabric. Rinse with clean water. Check all screws on a regular basis to maintain the solidity of the structure. 3
Pre-installation IMPORTANT: o not remove the protective film on the polycarbonate roof panels before installation (step 1 and 16). Make sure to put the U protected side facing the sun. It is a very important procedure; if not followed as described, your roof will not be covered by the warranty. PLANNING INSTALLATION It is the consumer s responsibility to comply with any building codes, ordinances, zoning limitations, or local homeowner s restrictions and obtain any required permit, before purchase and installation of the products. Make sure that all the parts are in the box before starting the assembly. Some parts may contain sharp edges, wear protective gloves. This unit will take at least 5 hours to set up. You must schedule enough time to complete the assembly. You cannot leave the sun shelter unattended if not fully assembled, even if bolted to the ground. At least 3 people are recommended for assembling the unit. Follow all instructions to assure the strength of the shelter. In order to avoid damage to the shelter and its components, use appropriate tools. o not use the structure as a support; a stepladder is recommended. Keep instructions and parts list for further reference. TOOLS RQUIR Not included in the box. Safety GoGgles Safety Hat Phillips Screw river Gloves Stepladder level
HArdware Kit NOT: Parts not shown to actual size and not to scale. T X8 U X16 X137 W X7 W1 X1 Y X1 Item escription Qty T M6 x 0 Screws 8 U M6 x 35 Screws 16 M6 x 16 Screws 137 W St5 x 15 Screws 7 W1 M5 x 15 Screws 1 Y Allen Key 1 5
PArts List F NOT: Parts not shown to actual size and not to scale. F1 C1 A C F B G G1 C3 B1 B G B3 C H X6 I1 J1 J J K Q L P R Ma Mb Part escription S X6 X S1 X1 Na Qty Part escription K I F Finishing Roof Side Structure (middle) Short Ogee G B1 Short Ogee B Short Track (Left) B3 C X1 K1 Nb X5 Z Qty Part escription Z1 Qty L Joint Cover Plate Left Roof Side Structure Ma Left Roof Panel (upper) G1 Right Roof Side Structure Mb Left Roof Panel (lower) G Middle Roof Side Structure Na Right Roof Panel (upper) Short Track (Right) H Bases Nb Right Roof Panel (lower) Long Ogee I Corner Cover P Mosquito Netting C1 Long Ogee I1 Column Cap Q Corner Finishing nds C Long Track (Left) J Left Roof Support Bar R Finishing nds 6 C3 Long Track (Right) J1 Right Roof Support Bar S Outside Roof Connector 1 Corner Roof Bar J Middle Roof Support Bar S1 Inside Roof Connector 1 Middle Roof bar 6 K Solidifying Bar X Hooks 5 F Finishing Roof Side Structure (left) K1 Solidifying Bar Z Middle Roof Panel (upper) F1 Finishing Roof Side Structure (right) K Solidifying Bar Z1 Middle Roof Panel (lower) A Column B 6
IMPORTANT: Always install the sun shelter on a level platform, wood or concrete. Step 1 1.1 Install Column (A) on Base (H) using Screws (W1). Repeat for all four Column (A). A W1 A H H A H W1 X1 7
NOT: Only the two bottom screws are to be inserted for this step. Step.1 Slide the Short Ogee (B) into the Short Ogee (B1).. Slide the Long Ogee (C) into the Long Ogee (C1)..3 Attach the Short Ogee (B) to the Short Ogee (B1) using Srews ().. Attach the Long Ogee (C) to the Long Ogee (C1) using Srews (). Repeat for all Ogees. B B1 C C1 B B1 C C1 B B1 C C1 X8 8
Step 3 3.1 Insert 6 Hooks (X) into Short Track (B). 3. Insert 6 Hooks (X) into Short Track (B3). 3.3 Insert 7 Hooks (X) into Long Track (C). 3. Insert 7 Hooks (X) into Long Track (C3). Repeat this step twice. Step.1 Install Long Track (C) into Long Ogee (C) using Screws ().. Install Long Track (C3) into Long Ogee (C1) using Screws ()..3 Install Short Track (B) into Short Ogee (B) using Screws ().. Install Short Track (B3) into Short Ogee (B1) using Screws (). Repeat this step twice. C B C1 C X X6 B3 C3 B1 B C X X6 B3 B C3 X X7 X X7 B C 0 B3 C3 X X5 9
CAUTION: 3 people are required for this step. Step 5 5.1 Install the Ogees (C & C1) between Columns (A). Use Screws (T) on the outside of the ogee and Screws (U) on the inside of the ogee. Finish the installation of the long ogees (C and C1) using Screws () from the inside of each column (A) as illustrated. 5. Install the Ogees (B & B1) between Columns (A). Use Screws (T) on the outside of the ogee and Screws (U) on the inside of the ogee. Finish the installation of the short ogees (B and B1) using Screws () from the inside of each column (A) as illustrated. Repeat this step twice. T U C C1 U T A T U B1 B C1 A C C C1 B B1 X8 T X8 U X16 10
Step 6 6.1 Install the Joint Cover Plates (L) using Screws (W) on the joint between the ogees (B & B1) and (C & C1). 6. Install the Corner Cover (I) using Screws (W) on each corner of the structure. Repeat this step times. W W I L W W B1 B C1 C W X3 I L 11
Step 7 7.1 Install Solidifying Bar (K) between ogees and fix in place using Screws () in order to form a triangle. 7. Install Solidifying Bars (K & K1) inside each structure bar and join the other end to the column using Screws (). Repeat this step for each four corner. K K K K1 K K1 K K1 K 8 1
Step 8 8.1 Fix the Roof Side Structure (G, G1 & G) on the Ogees (C & C1) using Screws (W). 8. Fix the Roof Side Structure (G & G1) on the Ogees (B & B1) using Screws (W). Repeat this step twice. G G1 G1 G G B1 B C1 W C G G1 G G1 G W 0 13
NOT: o not screw the column cap (I1) before step 11. Step 9 I1 9.1 Install Column Cap (I1) on top of Column (A). Repeat this step times. A Step 10 S1 10.1 Install Corner Roof Bars () to the Inside Roof Connector (S1) using Screws (). Repeat this step times. S1 S1 X1 I1 X8 1
Step 11 11.1 Place roof structure on top of ogees. 11. Screw Corner Roof Bar to the column using Screw (). Repeat this step times. 15
Step 1 1.1 Install Roof Bars () to the Inside Roof Connector (S1) using Screws (). 1. Screw Roof Bars () to the Ogees (B, B1,C & C1) using Screws (). Repeat this step 6 times. S1 X6 S1 X6 X1 X6 16
Step 13 13.1 Install the Outside Roof Connector (S) to the Inside Roof Connector (S1) using Screws (). S S1 S S X1 X3 17
CAUTION: One side of the roof panels is U protected. Make sure to put the U protected side facing the sun. It is a very important procedure; if not followed as described, your roof will not be covered by the warranty. NOT: The roof panels are covered with a plastic film identifying which side has a U protector. Once the plastic film is removed it is impossible to know which side has the U protector. We recommend removing the film one at a time just prior to installing the roof panel. Step 1 1.1 Install the Left Roof Panel (Ma) and the Right Roof Panel (Na) from the end of the roof bars according to the picture. Repeat this step times. 1. Insert Middle Roof Panels (Z) from the end of the Middle Roof Bars () in the middle of the 1ft side of the shelter. 1.3 Align the base of Middle Roof Panels (Z) with bases of the Left Roof Panels (Ma) and the Right Roof Panels (Na). This may require that Middle Roof Panels (Z) not be completely pushed to the back of the tracks. Repeat this step twice. This side up Ma, Na & Z & Ma Z Na Ma Na Ma Z Na 18
Step 15 15.1 Install the Roof Support Bars (J, J1 & J) according to picture. Make sure they are completely inserted in the tracks. 15. Align Middle Roof Support Bar (J) with Roof Support Bar (J & J1). CAUTION: nsure that the roof panels are completly inserted into the roof support bars (J, J1 and J). J, J1 & J & J J J1 J J1 J J1 J 19
CAUTION: One side of the roof panels is U protected. Make sure to put the U protected side facing the sun. It is a very important procedure; if not followed as described, your roof will not be covered by the warranty. NOT: The roof panels are covered with a plastic film identifying which side has a U protector. Once the plastic film is removed it is impossible to know which side has the U protector. We recommend removing the film one at a time just prior to installing the roof panel. Step 16 16.1 Install the Left Roof Panels (Mb) and the Right Roof Panels (Nb) according to the picture. 16. Insert Middle Roof Panel (Z1) from the end of the roof bars in the middle of the 1ft side of the shelter. Repeat this step for all remaining roof panels. This side up Mb, Nb & Z1 & Mb Z1 Nb Mb Nb THIS SI UP THIS SI UP Mb Z1 Nb 0
CAUTION: people are required for this step. Step 17 17.1 Secure the left side of a Finishing Roof Side Structure (F) with Screw () in the left corner of the 1 foot side of the unit. This screw () will be undone and re-inserted at the end of step 17 in order to finish the unit with a Corner Finishing nd (Q). 17. Place a roof Middle Roof Side Structure (F) next to the Finishing Roof Side Structure (F) and align the pre-drilled holes in each bar one on top of the other. Place Finishing nd (R) over the aligned holes and secure with Screw (). 17.3 Repeat this step with Finishing Roof Side Structure (F1) by securing it to Middle Roof Side Structure (F) with Finishing nd (R) and Screw (). 17. In order to transition from the 1 foot side of the unit to the 10 foot side, align the remaining pre-drilled hole of Finishing Roof Side Structure (F1) with that of a Finishing Roof Side Structure (F) on the 10 foot in the corner of the unit. Secure both bars in the corner with a Corner Finishing nd (Q) by inserting a Screw (). Q F F1 F F1 F Q F R Q X10 R X6 F F1 F 1
CAUTION: people are required for this step. NOT: The 10 foot sides of the unit do not require having Finishing Roof Side Structure (F) installed on them. Step 17 (continued) 17.5 Secure a Finishing Roof Side Structure Bar (F1) to Finishing Roof Side Structure (F) on the 10 foot side with Corner Finishing nd (R) and Screw (). 17.6 Repeat working your way around the entire unit until coming to the last corner where the installation of the Finishing Roof Side Structures began. 17.7 Undo screw () and align the pre-drilled holes of the first and last side structure which were installed. Secure both bars in the corner with a Corner Finishing nd (Q) by inserting a Screw (). Q F R F1 R
Step 18 18.1 Install the Mosquito Netting (P) along the tracks by inserting the Hooks (X) one at a time into the eyelets found along the top border of the netting. Repeat for all four mosquito panels. NOT: The netting should be installed starting in the middle of the 1 foot side of the unit, wrap around the inside of the post, and finish the installation in the middle of the 10 foot side of the unit. The zippers to close the netting will therefore meet in the center of the each side of the sun shelter. P P X P P 3
Please refer to part numbers when reordering For questions or comments about product: mail: piece@sojag.ca or Call toll-free: 1-866-901-169 Made in CHINA istributed by Sears, Roebuck and Co., Hoffman states, IL 60179 See our extensive assortment of outdoor living products on-line at www.sears.com and www.kmart.com Printed in China