SMT TR series Surface mount tiny washable rocker switches istinctive features and specifications Entirely designed for surface mount Tape and reel packaging Reflow solderable High temperature plastic materials Tin plated ground plate Terminal coating : tin alloy over nickel plating Terminals turned to the outside, preventing the shadow effect in infrared soldering and permitting visual inspection of solder joints istance between case and circuit : 0,55 mm (.021) End stackable with 10,16 mm (.40) pitch Available with positioning pins to ensure switch orientation during the reflow process and increasing switch mechanical resistance Protected against electrostatic discharges (ES) up to 10 KV Washable Construction withstands cleaning processes, including hot water under pressure ELECTRICAL SPECIFICATIONS PACKAGING Max. current/voltage rating with resistive load : 0,4VA 20V max. AC or C Minimum load : 10mA 50mV or 10µA 5VC Initial contact resistance : 20 mω max Insulation resistance : 1.000 MΩ min. at 500VC ielectric strength : 1.000 Vrms. 50 Hz min. between terminals and frame 500 Vrms. 50 Hz min. between terminals Electrical life at full load : - 2 position switches : 60.000 cycles - 3 position switches : 30.000 cycles Static resistance : 10 KV (Schaffner equipment) Unrolling direction 12.00 (.472) 44.00±0.30 (1.732±.011) GENERAL SPECIFICATIONS Operating temperature : -40 C to +85 C Moisture resistance : 21days per IEC 512-6 test 11c Vibration resistance : 10-500 Hz / 10 g per IEC 512-4 test 6d Shock resistance : 50 g per IEC 512-4 test 6c MATERIALS Case : high temperature plastic material UL94-V0 Actuator : high temperature plastic rocker Ground plate and positioning pins : steel, tin plated Contacts : brass, gold plated Terminals : brass, with pure tin plating over nickel barrier SOLERING AN CLEANING Reflow soldering : infrared, vapor phase or infrared convection Washable per IEA-RS448-2 : - water + detergent - preferred - solvents Further information on reflow soldering : see end of catalogue. Ø360.00 Maxi (14.173 IA MAX) Tape width 24.00 (.944) 44.00 (1.732) Reel (dimension A) Ø13.00±0.25 (.511 IA±.009) 40.40±0.10 (1.590±.003) 24.40+2.00/0.00 (.960+.078/.000) Ø100.00 mini (3.937 IA MIN) 3.00 (.118) 44.40+2.00/0.00 (1.748+.078/.000) Standard packaging unit : 700 pieces Tape meeting international standard IEC - Publication 286-3 (EIA481A) Start leader : 400 mm min. A imensions : First dimensions are in mm while inches are shown as bracketed numbers. -2 www.apem.com APEM
SMT TR series Surface mount tiny washable rocker switches With or without positioning pins Single pole 1 2 3 Without positioning pins TR36WS80000 ON - ON TR39WS80000 ON OFF ON TR37WS80000 MOM OFF MOM TR38WS80000 ON OFF MOM TR32WS80000 ON - MOM Supplied without rocker. 1.10 (.043) (.230) I II 24 3 2 1 (.318) III 1.80 (.070) 2.10 (.082) 6.90 (.271) 1.50 (.059) 7.96 (.313) 0.80 (.031) With positioning pins TR36WS80065 ON - ON TR39WS80065 ON OFF ON TR37WS80065 MOM OFF MOM TR38WS80065 ON OFF MOM TR32WS80065 ON - MOM Supplied without rocker. 1.10 (.043) 1.00 (.039) (.230) 9.45 (.372) 3.81 (.150) I II 24 3 2 1 (.318) III 0.65 (.025) 3.81 (.150) 1.50 (.059) 0.80 (.031) 6.90 (.271) Ø0.80 (.031 IA) 1.80 (.070) 2.10 7.96 (.082) (.313) ROCKERS Order separately. Rocker colours U4700 Replace last "0" by number 1 blue 5 yellow 1/4 dark blue 6 red 2 black 7 ivory 3 green 7/1 white 4 grey 9 orange APEM www.apem.com -3
TR series istinctive features and specifications Sealed Single piece case O-ring seal between actuator and bushing Epoxy sealed terminals Wide variety of contact materials Same PCB layout as tiny toggle (TL), pushbutton (TP) and slide switches (TG) ELECTRICAL SPECIFICATIONS Max. current/voltage rating with resistive load : - gold plated contacts : 0,4VA 20V max. AC or C - silver plated contacts : 0,5A 48V max. AC or C Minimum load : 10mA 50mV - 10µA 5VC Contact resistance : 20 mω max. Insulation resistance : 1.000 MΩ min. at 500VC ielectric strength : 1.000 Vrms 50 Hz min. between terminals and frame 500 Vrms 50 Hz min. between terminals Electrical life at full load : Contacts Number of cycles 2 positions 3 positions Gold plated Silver plated 60.000 30.000 20.000 10.000 MATERIALS Case : PBT Actuator : polyamide Contacts and terminals : 0 : brass, gold plated 1 : brass, silver plated 3 : brass, gold plated (1,27 micron gold) 8 : contact brass, gold plated + tin plated terminals 9 : contact brass, gold plated (1,27 micron gold) + tin plated terminals Terminal seal : epoxy GENERAL SPECIFICATIONS Strength of terminals : pull-out force - 10N max. Operating temperature : -30 C to +85 C Moisture : 21 days 95 % (NFC 20-603 - IEC 68-2-3) Cleaning : solvents or water + detergent Wave soldering : 260 C - 5 sec. -4 www.apem.com APEM
TR series Overview TR SERIES Number of poles Electrical functions Terminals 3 Single pole 4 ouble pole 6 ON - ON 9 ON OFF ON 7 MOM OFF MOM 8 ON OFF MOM 2 ON - MOM P0 Y0 W0 WW MW Straight PC Bracket mounting Right angle, horizontal mounting Right angle, vertical mounting Wire-wrap 00 Contacts and terminal materials 0 Brass, gold plated 1 Brass, silver plated 3 Brass, gold plated (1,27 micron gold) 8 Contact brass, gold plated + tin plated terminals 9 Contact brass, gold plated (1,27 micron gold) + tin plated terminals (SP only) Case colour 00 Blue Special options 00 No special requirement 07 Trimmed terminals - length 3,2 (.125) 08 Extended terminals 18 Switch without ground plate 20 Ground plate with 2 pins 25 Trimmed terminals - length 5 30 Wire-wrap on bracket mounting models 50 Crimped ground plate pins Rockers 10 Small 20 Large ABOUT THIS SERIES On the following pages, you will find successively : - model structure of switches - options in the same order as in above chart imensions : first dimensions are in mm while inches are shown as bracketed numbers. NOTICE : please note that not all combinations of above numbers are available. Refer to the following pages for further information. Packaging unit : 50 pieces. APEM www.apem.com -5
TR series Straight PC, right angle or wire-wrap terminals 1 and 2 pole configurations 1 2 3 3.30 (.129) 15.20 (.598) MOEL STRUCTURE Shown with small rocker (code 10) Straight PC terminals : TR..P0 Single pole ouble pole TR36P0 TR46P0 ON - ON TR39P0 TR49P0 ON OFF ON TR37P0 TR47P0 MOM OFF MOM TR38P0 TR48P0 ON OFF MOM TR32P0 TR42P0 ON - MOM 3.30 (.129) 9.30 (.366) (.318) 1 2 3 4 5 6 11.50 (.452) 1.00 (.039) 1 4 9.10 (.358) Straight terminals - bracket mounting : TR..Y0 Single pole ouble pole TR36Y0 TR46Y0 ON - ON TR39Y0 TR49Y0 ON OFF ON TR37Y0 TR47Y0 MOM OFF MOM TR38Y0 TR48Y0 ON OFF MOM TR32Y0 TR42Y0 ON - MOM 3.30 8.60 (.129) (.338) 0.40 (.015) 1 2 3 4 5 6 1.00 (.039) 1 4 9.10 (.358) Right angle terminals - horizontal mounting : TR..W0 I II III 24 ø1.10 Single pole ouble pole TR36W0 TR46W0 ON - ON TR39W0 TR49W0 ON OFF ON TR37W0 TR47W0 MOM OFF MOM TR38W0 TR48W0 ON OFF MOM TR32W0 TR42W0 ON - MOM 3.30 (.129) 3 2 1 6 5 4 5.05 (.198) 3.50 (.137) 3 6 9.60 3.30 (.318) (.377) (.129) ø1.10-6 www.apem.com APEM
TR series Right angle terminals - vertical mounting : TR..WW I II III Single pole ouble pole TR36WW TR46WW ON - ON TR39WW TR49WW ON OFF ON TR37WW TR47WW MOM OFF MOM TR38WW* TR48WW* ON OFF MOM TR32WW* TR42WW* ON - MOM * Functions 2 and 8 : reversed connection available. Consult factory. 3.30 (.129) 8.65 (.340) 3 6 3.50 (.137) 1 2 4 5 6 3 9.10 (.358) Wire-wrap terminals : TR..MW Single pole ouble pole TR36MW TR46MW ON - ON TR39MW TR49MW ON OFF ON TR37MW TR47MW MOM OFF MOM TR38MW TR48MW ON OFF MOM TR32MW TR42MW ON - MOM 15.20 (.598) 9.30 (.318) (.366) 11.50 (.452) (.318) 1.00 (.039) 1 4 1 4 2 5 3 6 9.10 (.358) PANEL CUT-OUT PCB MOUNTING 6.60 (.259) 14.80 (.582) 8.40 (.330) 14.80 (.582) 19.70 (.775) 19.70 (.775) 9.60 (.377) 4.60 (.181) 8.65 (.340) With small rocker With large rocker CONTACT AN TERMINAL MATERIALS 0 Brass, gold plated 1 Brass, silver plated 3 Brass, gold plated (1,27 micron gold) 8 Contact brass, gold plated + tin plated terminals 9 Contact brass, gold plated (1,27 micron gold) + tin plated terminals (single pole only) CASE COLOUR 00 Blue 00 APEM www.apem.com -7
TR series SPECIAL OPTIONS 00 No special requirement 07 Trimmed terminals - length 3,2 mm (.125) for TR..WW models only 3.20 (.125) 08 Extended terminals for TR..W0 models only 07 12.50 (.492) 18 Switch without ground plate for TR..WW models only 08 20 Ground plate with 2 pins for TR..WW models only 18 2.70 (.106) 25 Trimmed terminals - length 5 mm for all models, except TR..WW 20 30 Wire-wrap terminals on models with mounting bracket 25 50 Crimping of ground plate pins. Retains switch on PCB during handling and wave soldering. For models TR..W0, TR..WW and TR..Y0 single and double pole. 30 15.20 (.598) Marking on rocker : consult factory. 50 ROCKERS Rocker colours Replace "0" by number 10 20 Small Large 7.62 (.300) 1 blue 1/4 dark blue 2 black 3 green 4 grey 5 yellow 6 red 7 ivory 7/1 white 9 orange -8 www.apem.com APEM
Selection guide - Section Rocker and paddle switches New! Series SMT TR TR S-SR AS MT 7000 FM Page -2-4 -9-19 22-24 -42 Poles 1 1,2 1,2 1 1 1,2 1 Maximum ratings 0,4VA 0,5A (2A 250VAC)* (2A 250VAC)* 4A 30VC (3A 250VAC)* (10A 250VAC)* 20V AC/C 48V AC/C 4A 30VC 4A 30VC Illuminated X Mounting options Horizontal SMT X Vertical Through hole X X X X X X Horizontal Through hole X X X Vert. right angle TH X X X Snap-in X X X X Rear mounting X X Panel cut-out 18,65X8,9 Ø 17,65 19,2x12,9 Terminal options PCB X X X X X X X Solder lugs X X X X X Quick-connect X Sealing Process sealed Process sealed Process sealed No No No Optional boot ( )* See applicable approvals Series 2600 KR KL KI KG Page -45-53 -62-71 -76 Poles 1,2 1,2 1,2 1,2 Maximum ratings (16A 250VAC)* 10A 24VC 10A 24VC 24VC (12A 250VAC)* 15A 12VC Illuminated X X X X X Mounting options Snap-in X X X X X Panel cut-out 30 x 22 36,8 X 21,08 36,8 X 21,08 36,8 X 21,08 36,8 X 21,08 Terminal options Solder lugs X X X X X Quick-connect X X X X X Screw X X X X Sealing Optional boot IP68 IP68 IP68 IP65 12