PLEASE REFER TO THE DIAGRAM BELOW TO INSURE WE BUILD THIS ITEM TO YOUR EXACT SPECIFICATIONS. In back In back Outback Outback Welt Seat Cushion Seat Cushion Border Seat Deck Seat Welt Arm Pad Arm Pad Welt Lumbar pillow Lumbar pillow welt Finish Euro Beech Frame, Indonesia Dimensions: Outside: 31 W x 36 D x 51 H Inside: 26 W x 21 D x 50 H Seat: 26 H Arm: 26 H. SEND COM/COL FABRIC OR LEATHER AND IDENTIFICATION SHEET TO: Trutin, Inc., 230 South Road, Dock #11, High Point, NC 27262 For questions call Currey Customer Service at 678-533-1500 or your Sales Representative.
Finish: If specifying a Benjamin Moore paint color, you must attach a paint chip with the color name and number. There is a $35.00 up charge on each chair. SPECIFY YOUR MATERIAL IF ALL IN ONE FABRIC OR LEATHER: COM COMPLETE PIECE YARDAGE REQUIREMENT: 8 yards (Based on 54 plain fabric. For patterned fabrics refer to the repeat chart.) COL COMPLETE PIECE FOOTAGE REQUIREMENT: 144 feet If you are using two or more fabrics or leathers indicate placement below. If placing a COM or COL order refer to yardage and footage requirements below. If using Currey fabrics or leathers you need only specify fabric/leather pattern, color and Currey number. If using two or more Currey fabrics or leathers with different grades, price the piece using the higher grade. In back: COM/COL REQUIREMENT: 2 yds. fabric, 25 ft. leather *In back welt : COM/COL REQUIREMENT: ½ yd. fabric, 10 ft. leather Outback: COM/COL REQUIREMENT: 2 yds. fabric, 25 ft. leather *Outback welt: COM/COL REQUIREMENT: ½ yd. fabric, 10 ft. leather Seat cushion: COM/COL REQUIREMENT: 2 yds. fabric, 25 ft. leather *Seat cushion welt : COM/COL REQUIREMENT: ½ yd. fabric, 10 ft. leather Seat cushion border: COM/COL REQUIREMENT: 1 yd. fabric, 20 ft. leather Seat deck: COM/COL REQUIREMENT: ½ yd. fabric, 10 ft. leather *WELT: If providing a COM material for welt on anything other than pillows, please send fabric and not actual welt. Due to the construction of the frame, it is necessary that we make custom welt out of the COM fabric you provide. CONTINUED ON NEXT PAGE
Arm pad: COM/COL REQUIREMENT: ¼ yd. fabric, 5 ft. leather *Arm Pad Welt: COM/COL REQUIREMENT: ¼ yd. fabric, 5 ft. leather SPECIFY YOUR MATERIAL (include special instructions i.e. bias, reverse welt): 1 Lumbar Pillow: COM/COL REQUIREMENT: ¼ yd. fabric, 10 ft. leather *1 Lumbar Pillow welt: COM/COL REQUIREMENT: 68 trim, ¼ yd. fabric, 5 ft. leather WELT: If providing a COM material for welt on anything other than pillows, please send fabric and not actual welt. Due to the construction of the frame, it is necessary that we make custom welt out of the COM fabric you provide.
COM FABRIC REPEAT CHART/RAILROADING FABRIC REPEAT REPEAT REPEAT REPEAT REPEAT REPEAT WIDTH Up to 4 >4-15 >15-21 >21-27 >27-36 Centered up to the roll 54 0% 15% 25% 35% 45% 75% 50 15% 30% 40% 50% 60% 100% 48 20% 40% 50% 60% 70% 125% 45 50% 55% 65% 75% 85% 135% 36 60% 75% 85% 95% 100% 175% To estimate correct yardage when the vertical repeat is ½ through 27, you must add the horizontal repeat to the vertical repeat. For example, a 54 fabric with an 8 vertical repeat and a 12 horizontal repeat = a 20 total repeat. Therefore, if a chair takes 8 yards of 54 wide plain fabric, then a fabric with an 8 vertical repeat and a 12 horizontal repeat will require 25% more fabric, or approximately 10 yards. Railroaded fabric/pattern Railroading refers to the way a fabric, usually a pattern, is milled. Normally a bolt of fabric features the top of a pattern going up the roll. However, a railroaded fabric will have the top of the pattern going across the roll. This provides a continuous roll of the pattern, making it possible to upholster a large sofa, cushion or draperies without creating seams or a break in the pattern.
COM/COL INDENTIFICATION (PLEASE INCLUDE WITH YOUR ORDER) If there are multiple fabrics for this style, please complete a separate form for each and check here. Attach a cutting of the fabric face up and mark the direction of application. Customer Name PO # Side Mark Currey Ack # Name and Number of Currey Style Quantity Fabric Source Pattern Color Description Fabric Width Pattern Repeat V H Yardage Sent to Factory Fabric to be applied Up the Roll Fabric to be applied Railroad Note: Some fabrics require backing especially chenille, silk and linen. If you don t know if your fabric will need backing please send a cutting and this form to our factory at the address below to inquire. Trim Source Pattern/Color Trim Application FAILURE TO PROVIDE US WITH SPECIFIC APPLICATION INSTRUCTIONS AUTHORIZES US TO USE OUR OWN DISCRETION WHEN CUTTING AND UPHOLSTERING YOUR FABRIC. Special Instructions SEND COM/COL FABRIC OR LEATHER AND IDENTIFICATION SHEET TO: Trutin, Inc., 230 South Road, Dock #11, High Point, NC 27262 For questions call Currey Customer Service at 678-533-1500 or your Sales Representative.