BLUE ANT FURNITURE TITLE: FULL BUNKBED INSTRUCTIONS 10/10/09 DWG. NO. INSTR_888-FULL-BUNK SHEET 1 OF 9

BLUE ANT FURNITURE TITLE: FULL BUNKBED INSTRUCTIONS 10/10/09 DWG. NO. INSTR_888-FULL-BUNK SHEET 1 OF 9

WARNING: Failure to follow these warnings and assembly instructions could result in serious injury. Read all instructions before assembling bed. KEEP INSTRUCTIONS FOR FUTURE USE. Before each usage/assembly, inspect brackets/posts/slats, for damage and/or loose parts. Contact retailer regarding any damage. Follow all warning labels printed on carton. Always use recommended size mattress and box spring. Periodically, check side rails and slats for damage. Verify that all connections are tight. Prohibit children from jumping on bed. NOTE: This bed is adjustable to (3) positions. These positions are noted to the side. The 'Toddler Position' is lower than the 'Standard Position' making it easier and safer for a younger child s first big bed. If you purchased the Blue Ant Trundle - use the 'Standard Position.' If you purchased the Blue Ant Capt' Pedestal - use the 'Capt' Pedestal Position.' CAPT'N PED STANDARD TODDLER PRE-ASSEMBLY: Please read all instructions before beginning assembly. The illustrations provided allow for easier assembly when used in conjunction with the assembly instructions. RIGHT SIDE ENTRY For your safety and ease, assembly by (4) adults is recommended. Remove all parts and hardware from box and verify that all parts are complete and undamaged. Contact retailer if there are any broken or missing parts. Do not dispose of any contents until assembly is completed to avoid accidentally discarding small parts or hardware. The use of power tools for assembly is not recommended. Power tools can damage hardware or split wood. Determine location for bed. Top bunk can be assembled as either right entry or left entry. Note: placing ladder to a wall will reduce childrens ability to swing from ladder. CAPT'N PED STANDARD TODDLER LEFT SIDE ENTRY SHEET 2 OF 9

PARTS LIST 4 9 10 8 6 14 17 15 11 5 12 7 2 3 13 1 ITEM NO. Description QTY. 1 HEADBOARD PANEL 2 2 SIDE RAIL 2 3 SLAT ROLL 30 4 BUNK FOOTBOARD 2 5 BUNK WOOD DOWEL 4 6 GUARD RAIL 1 7 SAFETY SIDE RAIL 1 8 SAFETY RAIL 1 9 SAFETY RAIL SUPPORT 2 10 SAFETY RAIL METAL BRACKET 2 11 1/4" M6 X 2" ALLEN BOLT 6 12 STRAIGHT PLATE 1 13 BUNK LADDER 1 14 1/4" M6 X 5" ALLEN BOLT 11 15 1/2" BARREL NUT 11 16 FINIAL 4 FINIALS NOT SHOWN, SEE PANEL SET-UP. SHEET 3 OF 9

4 USE THESE HOLE FOR LEFT SIDE ENTRY. DO NOT USE 2 6 DO NOT USE USE THESE HOLE FOR RIGHT SIDE ENTRY. 3 STEP 1: WITH SIDE RAIL FACE DOWN PLACE WOOD BLOCKS BELOW DESIRED HOLES NOTED ABOVE. USING ELECTRIC DRILL AND 1/4" BIT, DRILL THROUGH TAP HOLES ONLY ENOUGH TO CREATE HOLE THROUGH SIDE RAIL. APPROXIMATELY 1/4". 1 5 ITEM # DESCRIPTION QTY. 1 SAFETY SIDE RAIL 1 2 SAFETY RAIL 1 3 SAFETY RAIL SUPPORT 2 4 SAFETY RAIL METAL BRACKET 2 5 1/4" M6 X 2" ALLEN BOLT 6 6 STRAIGHT PLATE 1 7 5/8" WOOD SCREWS 6 STEP 2: USING ALLEN WRENCH, ATTACH SUPPORTS TO SIDE RAIL AND SAFTEY RAIL WITH METAL BRACKET ON BACK SIDE. MAKE SURE METAL BRACKET HAS THREADED NUTS TO INSIDE. TOOLS REQUIRED: 1) ELECTRIC DRILL WITH 1/4" BIT. 2) PHILLIPS SCREW DRIVER. 3) ALLEN WRENCH SUPPLIED WITH HARDWARE KIT. 4) (2) PIECES 1" X 6" X 6" WOOD BLOCK. STEP 3: ATTACH SAFETY RAIL STRAIGHT BRACKET TO BACK SIDE USING PHILLIPS SCREWDRIVER AND (6) WOOD SCREWS. SHEET 4 OF 9

DETAIL A SCALE 1 : 4 1/4" M6 X 5" ALLEN BOLT 1/2" BARREL NUT A GUARD RAIL B DETAIL B SCALE 1 : 8 SAFETY RAIL W/ SIDE RAIL SLAT ROLL BUNK FOOTBOARD STEP 4: ATTACH GUARD RAIL TO BOTH FOOTBOARDS USING ALLEN WRENCH, 5" ALLEN BOLT AND 1/2" BARREL NUT. C DETAIL C SCALE 1 : 8 STEP 5: ATTACH SAFETY RAIL TO BOTH FOOTBOARDS USING ALLEN WRENCH, 5" ALLEN BOLT AND 1/2" BARREL NUT. STEP 6 : UNROLL SLAT PACK, PLACE ON SIDE RAIL CLEATS. ATTACH BOTH ENDS OF EVERY SLAT TO SIDE RAIL CLEATS USING SCREWDRIVER AND 1" WOOD SCREWS. CONTINUE UNTIL ALL SLATS ARE ATTACHED. SET ASIDE UNTIL FINAL ASSEMLBY. SHEET 5 OF 9

1" WOOD DOWEL DETAIL D SCALE 1 : 12 CAPT' PED D STANDARD TODDLER SIDE RAIL SLAT ROLL BUNK HEADBOARD STEP 7: WITH HEADBOARD IN DESIRED LOCATION, INSERT SIDE RAIL INTO POST. MAKE SURE THAT HOOK SITS ON PINS IN POST AND SIDE RAIL LOCKS FIRMLY AGAINST POST. IF SIDE RAILS DO NOT LOCK PROPERLY, CONTACT RETAILER. ATTACH FOOTBOARD IN SAME MANNER. STEP 8: ATTACH SECOND SIDE RAIL IN SAME MANNER AS FIRST. AGAIN, MAKE SURE ALL HOOKS LOCK PROPERLY. IF ANY DOES NOT LOCK PROPERLY, CONTACT RETAILER. STEP 9: UNROLL SLAT PACK, PLACE ON SIDE RAIL CLEATS. ATTACH BOTH ENDS OF EVERY SLAT TO SIDE RAIL CLEATS USING SCREWDRIVER AND 1" WOOD SCREWS. CONTINUE UNTIL ALL SLATS ARE ATTACHED. INSERT 1" WOOD DOWELS INTO POSTS. SHEET 6 OF 9

FINAL ASSEMBLY: 1) PLACE ASSEMBLED HEADBOARD INTO DESIRED LOCATION. 2) SET TOP BUNK ONTO WOOD DOWELS IN HEADBOARD POSTS. 3) ATTACH LADDER TO TOP BUNK BED USING PHILLIPS SCREWDRIVER AND 5/8" WOOD SCREWS TO INSIDE FACE OF SAFETY SIDE RAIL. SHEET 7 OF 9

CONVERTING BUNKBED TO INDIVIDUAL PANEL BED INDIVIDUAL PANEL BEDS: THIS BUNK ASSEMBLY CAN BE CHANGED TO ONE OR TWO INDIVIDUAL PANEL BEDS SHOULD YOU CHOOSE TO. IF ONLY ONE PANEL BED IS DESIRED, REVERSE THE ASSEMBLY INSTRUCTIONS. IF TWO PANEL BEDS ARE DESIRED, YOU WILL NEED TO PURCHASE (1) ADDITIONAL SET OF SIDE RAILS. YOU HAVE EVERYTHING ELSE YOU NEED. NOTE: FOR SAFETY REASONS, (4) PEOPLE SHOULD PERFORM THE FOLLOWING PROCEDURES. STEP 1: REMOVE LADDER AND SET ASIDE. STEP 2: REMOVE TOP BUNK. STEP 3: UNASSEMBLE TOP BUNK BY REMOVING SLAT ROLL FROM GUARD AND SAFETY RAILS. STEP 4: REMOVE HARDWARE HOLDING GUARD AND SAFETY RAILS TO PANELS. SET RAILS ASIDE. BAG ALL K-D HARDWARE AND PLACE WITH RAILS STEP 5: UNASSEMBLE BOTTOM PANEL ASSEMBLY BY REMOVING SLAT ROLL FROM SIDE RAILS. STEP 6: UN-HOOK SIDE RAILS FROM PANELS. STEP 7: INSPECT ALL COMPONENTS FOR SPLITS, BREAKS OR ANY DAMAGE BEFORE PROCEDING. IF THERE IS ANY DAMAGE, CONTACT RETAILER FOR REPLACEMENT PARTS. SHEET 8 OF 9

FINIAL DETAIL D SCALE 1 : 12 BUNK HEADBOARD CAPT' PED D STANDARD TODDLER SIDE RAIL SLAT ROLL BUNK FOOTBOARD STEP 9: LOCATE ALL OF THE COMPONENTS ABOVE. STEP 10: DETERMINE WHICH WILL BE USED FOR STAND ALONE BED. STEP 11: WITH HEADBOARD IN DESIRED LOCATION, INSERT SIDE RAIL INTO POST. MAKE SURE THAT HOOK SITS ON PINS IN POST AND SIDE RAIL LOCKS FIRMLY AGAINST POST. IF SIDE RAILS DO NOT LOCK PROPERLY, CONTACT RETAILER. ATTACH FOOTBOARD IN SAME MANNER. FINIAL C DETAIL C SCALE 1 : 8 STEP 12: ATTACH SECOND SIDE RAIL IN SAME MANNER AS FIRST. AGAIN, MAKE SURE ALL HOOKS LOCK PROPERLY. IF ANY DOES NOT LOCK PROPERLY, CONTACT RETAILER. STEP 13 : UNROLL SLAT PACK, PLACE ON SIDE RAIL CLEATS. ATTACH BOTH ENDS OF EVERY SLAT TO SIDE RAIL CLEATS USING SCREWDRIVER AND 1" WOOD SCREWS. CONTINUE UNTIL ALL SLATS ARE ATTACHED. STEP 14: PLACE FINIALS IN HOLES ON HEADBOARD. SHEET 9 OF 9