Size of Mattress and oundation The length and width of the upper bunk mattress and foundation are as follows : Length 74-75 Width 37 ½ - 38 ½ Thickness 9 ½ max You must use only this size mattress. nsure thickness of mattress and foundation combined does not exceed 9 ½ and that the mattress is at least 5 below upper edge of guardrails. This unk ed uses a slat kit for mattress foundation. Replacement Parts Replacement parts, including additional guardrails, may be obtained from any tlantic urniture dealer STY WRNINS!! ( 1 ) ( 2 ) ( 3 ) ( 4 ) ( 5 ) ( 6 ) ( 7 ) ( 8 ) ( 9 ) () (11) (12) (13) (14) ollow the information on the warnings appearing on the upper bunk end structure and on the carton. o not remove warning label from bed. lways use the recommended size mattress or mattress support, or both, to help prevent the likehood of entrapment or falls. Surface of mattress must be at least 5 in. (127mm) below the upper edge of guardrails. o not allow children under 6 years of age to use the upper bunk. Periodically check and ensure that the guardrail, ladder, and other component are in their proper position, free from damage, and that all connectors are tight. o not allow horseplay on or under the bed, and prohibit jumping on the bed. lways use ladder for entering or leaving upper bunk. o not use substitute parts. Contact the manufacturer for replacement parts. Use of a night light may provide added safety precaution for a child using the upper bunk. lways use guardrails on both long sides of the upper bunk. If the bunk bed will be placed next to a wall, the guardrail that runs the full length of the bed must be placed against the wall to prevent entrapment between the bed and the wall. The use of water or sleep flotation mattress is prohibited. Prohibit more than one person on upper bunk. STRNULTION ZR : Never attach or hang items to any part of the unk ed that are not designed for use with the bed: for example, but not limited to, hooks, belts and jump ropes. Keep these instructions for future reference. UNK STY WRNIN Page 1 of 8
RY WOOLN UNK SSMLY INSTRUCTIONS TWIN - TWIN Thank you for choosing our new bunk bed. This practical design offers the utmost in versatility. efore assembling your Woodland bunk bed, please read through these instructions carefully, familiarize yourself with the different parts. Please note that you will require a Phillips head screwdriver and an llen wrench. llen wrench Phillips ead Screwdriver UNK SOWN WIT LR URRIL CN ST UP T ITR N O T UNK RWR NOT : W INCLU SPR RWR IN CS T LLN WRNC, LLN SCRW, JC, RRL NUT WOON OWL OR WOO SCRW R M URIN SSMLY. JC M6 X 3 1/8-16 pcs Spare - 2 pcs llen Screw M6 X 2" - 4 pcs Spare - 1 pc Metal Pins - 4 pcs arrel Nut - 16 pcs Spare - 2 pcs Wood Screw 1" - 4 pcs Spare - 1 pc Wood uttons - 4 pcs C Wooden owel - 8 pcs Spare - 2 pcs Wood Screw 5/8" - 4 pcs Spare - 1 pc WOOLN UNK TWIN-TWIN Page 2 of 8 I llen wrench - 1 pc Spare - 1 pc
PRTS LIST 04 05 09 01 RWR UPPR PNL 1 OX 01 LOWR PNL 1 OX 04 ULL URRIL 05 3/4 URRIL LT N CPS RIT N CPS LON RILS 1 OX 09 CLIP ON LR TWIN SLT KIT 1 OX 1 OX 2 ST WOOLN UNK TWIN-TWIN Page 3 of 8
STP 1 ttach the long rails () to the upper panels (), using JC M6 X 3 1/8 () and barrel nut (). Tighten with the llen wrench (I). JC M6 X 3 1/8 arrel Nut I llen wrench STP 2 Insert wooden dowel (C) to the locator holes will receive (C) as shown below. ttach the full guard rail (04) to the left, right end caps ()(), using llen screw (),Tighten with the llen wrench (I). Repeat for 3/4 guard rail (05). 04 C C C Wooden owel 05 JC M6 X 2 I If the bunk bed will be placed next to a wall, the guard rail that runs the full length of the bed should be placed against the wall to prevent entrapment between the bed and the wall. llen wrench WOOLN UNK TWIN-TWIN Page 4 of 8
STP 3 Lay the twin slat kit () onto the bed. ix in place using wood screws provided in the slat kit box. OR SLT KIT SSMLY follow assembly instructions included with slat kit. Phillips head screwdriver STP 4 Install the full and 3/4 guard rail assemblies onto the long rails, and fix in place using wood screws (). Tighten with the Phillips head screwdriver.( ) ULL UR RIL SSMLY 1 Wood Screw 3/4 UR RIL SSMLY Phillips head screwdriver URRIL CN ST UP T ITR N O T UNK WOOLN UNK TWIN-TWIN Page 5 of 8
STP 5 ttach the long rails () to the lower panel (), using JC M6 X 3 1/8 (), and barrel nut (). Tighten with the llen wrench (I). JC M6 X 3 1/8 arrel Nut I llen wrench STP 6 Lay the twin slat kit () onto the bed. ix in place using wood screws provided in the slat kit box. OR SLT KIT SSMLY follow assembly instructions included with slat kit. Phillips head screwdriver WOOLN UNK TWIN-TWIN Page 6 of 8
STP 7 Insert metal pins () into the holes in top of the lower panels. Lift the upper panels onto the lower panels as shown, and fit the metal pins into the holes in the bottom of the upper panel legs. Metal Pins CUTION! This step requires two strong people. STP 8 Lastly, install Clip on Ladder (09). Using wood screw () tighten with Philips head Screwdriver. UPPR LOWR Wood Screw 5/8" 09 Phillips head screwdriver WOOLN UNK TWIN-TWIN Congratulations! Your Woodland bunk bed is now ready for use. We recommend that you recheck that all screws are tight, and that all parts are secure before use. Periodically to ensure lasting Safety. Page 7 of 8
CONVRSION TO 2 TWIN S. isassemble upper bunk by removing guard rails. lso remove metal pin from lower bunk. Metal Pin UPPR UNK LOWR UNK isassemble upper bunk by removing upper panel () and lower bunk by removing lower panel(). xchange upper panel to the lower panel position and Install hardware tighten with llen wrench. UPPR UNK LOWR UNK Use Wood button () to cover holes as shown below. TWO TWIN S WOOLN UNK TWIN-TWIN Wood utton Page 8 of 8