BluePunch Key Machine The Blue Punch key machine is a dedicated key punch machine designed to provide factory original keys. Creates keys with the speed of a duplicator.the Blue Punch is fast, extremely accurate and easy to use.the machine is set up at the factory to provide automatic spacing and depth.an ideal machine for the commercial locksmith, hotels, schools and other institutions. Fast and easy to use, this machine is precision machined to the tightest tolerances. Heavy duty and built to last. Portable and dependable, hand operated no electrical outlet needed. BluePunch Key Machine Keyway Specifics PART # DESCRIPTION SPECIFIC KEYWAYS BP201ARFC ARROW FLEXCORE Arrow Flexcore 51, 52, 53, 54, 61, 81, 83, 84 BP201C70 CORBIN C70 Most Popular Corbin System 70 Keyways 59 Series A1,A2, B1,B2,D2 60 Series 6 pin BP201DE DEXTER / MASTER Master Door Locks All Dexter Cylinders BP201FW FALCON WEISER Falcon Standard (Non I/C) *Will Not Cut 8 Or 9 Depths All Weiser Cylinders BP201IC I-CORE A2 SYSTEM A2 Standard Interchangeable Core (I/C) Best, Falcon & Arrow Small Format I/C Key Sections A-R,TA-TE,W Arrow 1A-4D Exclusions:Arrow Flexcore, Kaba Peaks, Insta-Key BP201IC-A3 I-CORE A3 SYSTEM Interchangeable Core (I/C) A3 System BP201IC-A4 I-CORE A4 SYSTEM Interchangeable Core (I/C) A4 System BP201KW KWIKSET Kwikset Standard & Yale Residential *Titan (Will Not Cut Titan 5 & 6 Pin Or Titan Square 1st Cut ) BP201SC SCHLAGE-CLASSIC Schlage Classic (Including Ic) Obverse Key Sections Only C, CE, E, EF, F, FG, G, H, J, K, L (Aftermarket L Blanks Only) Primus Same Key Sections As Obverse Except A P Has Been Added To Keyway # (ie: CP, CEP, EP, Etc.) Schlage Everest C (Including I/C) Key Sections (I.E.C123, C124, C126, C135, C145) Everest Primus Uses Same Names Exclusions: Numbered Key Sections, Quad Key Sections, Reverse Key Sections, Everest B (B + 3 Digits), Everest D (D + 3 Digits) BP201SCEB SCHLAGE-SMALL FORMAT Schlage Everest B Key Sections Only B123,B125, B234, B235 All Other Keys With A B + 3 Digits BP201SCRV SCHLAGE-REVERSE Schlage Reverse Sections D,DQ,Q,QS,S,T,U,V,W &Y BP201WK WESLOCK All Weslock Cylinders 368
Mortise Lock Installation Jig Pro-Lok Mortise Lock Installation Jig INJIG-MORT The self-centering mortise jig has been used by locksmiths for over 15 years and is renowned for its accuracy, efficiency and depth of cut. Pro-Lok has now refined and improved the engineering standards to ensure superior quality and reliability.the new jig incorporates unique Quick Change Cutters which allow the cutters to be changed in seconds, without removing the jig from the door.this means that both the full lock body and face-plate can be cut out with ease. With the PRO-LOK Mortise Jig time on the site is reduced and accuracy is assured with minimum disruption to the customer. No other combination of tools can produce such fast and accurate mortise installations.this tool is a must have tool for the professional locksmith. Cuts a Mortise into all Wooden and Aluminum Doors The jig and its precision cutters will cut a mortise in hard wood, soft wood, composite doors and with the use of special cutters, aluminum doors as well, all in under five minutes! Replacement Parts INJIG-MORT-HK Aluminum Housing with hardware INJIG-MORT-SS Short Boring Shaft (for locks up to 3-1/2" deep) INJIG-MORT-LS Long Boring Shaft (for locks up to 6" deep) INJIG-MORT-GS Set of 6 Allen Set Screws INJIG-MORT-CC Carrying Case Replacement Wood Cutters INJIG-MORT-WB16 5/8" INJIG-MORT-WB18 11/16" INJIG-MORT-WB19 3/4" INJIG-MORT-WB21 13/16" INJIG-MORT-WB22 7/8" INJIG-MORT-WB24 15/16" INJIG-MORT-WB25 1" INJIG-MORT-WB27 1-1/16" INJIG-MORT-WB32 1-1/4" Aluminum Cutters INJIG-MORT-AB19 3/4" INJIG-MORT-AB25 1" INJIG-MORT-AB32 1-1/4" Overall Assessment The 5 minute Mortise Jig is a time and labor-saving device which takes the hard work out of fitting a mortise lock. It is manufactured to high standards and is very easy to use. The mortise hole is automatically centered on the door and accurate results are obtained every time. The cutters can be quickly changed and sharpened locally to maintain their cutting efficiency. A range of cutters are included for wood and available for aluminum doors. Reasonably priced. An indispensable tool for all mortise lock installers. Included in the Kit Carry case, aluminum housing with hardware, 3 cutters, self-centering action, stops, long boring shaft (greater depth than any router) and instructions. 369
In-Temp Who can install a vertical rod exit device with outside trim in less than one hour? You can with the PRO-LOK IN-Series Templates. They're easy to use, precise and durable.these templates are used with the INCL Universal Clamp.You will get exacting accuracy and finish the job in the same time it takes others to set up. Every time you use a PRO-LOK template, your installation time will decrease and your installations will become more precise and professional looking.time is money the PRO-LOK IN-Series Templates may be the best investment you ever make! Reverse templates are also available for the back side of the door.you can cut your time in half by not having to switch over when you are done with one side and prevent splintering of the back side of the door when drilling. Perform Professional Installations in a Fraction of the Time! Installation Template Application Chart MAKE MODEL IN# Alarm Lock Trilogy IN10 Alarm Lock Trilogy T-2 IN15 Arrow Sierra H-Series IN75 Authority 8160 Series IN20 Baldwin Mortise Locks IN65 Best 7K Series IN20 Best 9K Series IN79 Corbin/Russwin 800 Series IN70 Corbin/Russwin CL3400 Series IN70 Cal-Royal Pioneer Series IN20 ITEK Grade 1 Levers IN78 Lockwood 8000 Series IN20 LSDA LX1000 Series IN78 Marks 195 Series IN78 Marks 295 Series IN78 Medeco Embassy 17 Series IN20 Medeco Embassy 19 Series IN78 NT Falcon T-Series IN20 MAKE MODEL IN# NT Monarch 18 Series IN318 Precision 11 Series IN311 PDQ SP-Series IN20 S. Parker 8161 Series IN20 Schlage D Series IN20 Schlage H Series IN60 Schlage L Series IN50 Schlage Rhodes IN20 Sargent 10 Line IN75 Sargent 6500 Line IN78 Simplex 1000 IN10 Taco Grade 1 Levers IN78 U.S. Lock 2000 Series Levers IN78 Von Duprin 99 Series IN30 Von Duprin 9927 IN40 Yale 5400L IN20 Yale AU/PB IN77 INEXT5 IN13R OUT SIDE Use with INCL to prep for 5" backsets. IN13 Kaba-Ilco 850-850L-950 Preps doors for the Unican/Kaba-Ilco Solitaire cylindrical locks.this template is for the outside and should be used with the INCL Universal clamp. IN SIDE Kaba-Ilco 850-850L-950 Preps doors for the Unican/Kaba-Ilco Solitaire cylindrical locks.this template is for the inside and should be used with the INCL Universal clamp. 370
In-Temp IN10 Simplex/Trilogy Preps door for Simplex 1000 Series locks and Trilogy push button locks. IN10R Reverse Simplex/Trilogy Same as IN10 but preps reverse side of door. IN12 ILCO 4000 Series Preps door for ILCO 4000 series. IN15 Alarm Lock Trilogy T-2 Preps door for the Trilogy T-2 Series locks. IN20 Schlage Rhodes Preps door for various popular lever locks. Ideal for retrofitting where olympiads were installed. IN20BL Blank 5-1/2" high x 5" wide. Make your own template. IN30 Von Duprin 99 Body Preps door for 99 series exit devices. Includes trim preps for Thumb piece, rim, lever, knob, and cylinder. IN30BL Blank 12" high x 5" wide. Make your own template. IN40 Von Duprin Vertical Rod Preps door for top and bottom latch units and guide brackets. Use with IN30 for a complete installation of a 9927 series device. IN40R Reverse Von Duprin Same as IN40 but preps the reverse side of door. IN50 Schlage L Preps door for Schlage L series locks. IN50BL Blank 8-1/2" high x 5" wide. Make your own template. IN50R Reverse Schlage L Same as IN50 but preps the reverse side of door. IN51 Mortise Lock Pocket Center Use with IN50 to center the template on a door with the mortise pocket already cut out. IN60 Schlage H Preps doors for Schlage H series locks. Comes with IN61 disk adaptor to bore either 2-1/8" or 1-1/2" holes. IN61 Replacement Disk Replacement disk for IN60. 371
In-Temp IN65 Baldwin Preps doors for Baldwin mortise locks. Use with all popular handle designs. Includes backset spacer for a variety of backset applications. IN67 Replacement backset for IN65. IN70 Corbin/Russwin Preps doors for Corbin and Russwin 3400/800 series lever locks. IN75 Arrow/Sargent Preps doors for Arrow & Sargent heavy-duty Grade 1 lever locks. IN77 Yale AU/PB Preps doors for Yale heavy-duty AU/PB series lever locks. IN78 Grade 1 Lever Locks Preps door for various heavy duty lever locks. Allows you to drill the 2-1/8" body prep and the post holes at 12 & 6 o clock. IN79 Best 9k Preps doors for heavy duty Best 9K lever lock.allows you to drill the post holes at 12 & 6 o clock. IN311 Precision #11 Preps door for Precision #11 exit devices. Works with any door and accommodates gap between the door and frame. IN318 Monarch #18 Preps door for Monarch #18 series exit devices.works with any door and accommodates gap between the door and frame. INBIT Router Bit Use the INBIT with the IN30 for installing the popular Von Duprin 99 series exit devices. The bit works with a plunge router and is perfect for installation on wood door applications. INCL Universal Clamp The cornerstone of our Professional Installation Series. Holds all of our specialty templates without damage to the door s finish. Complete with an easy to use 1-1/2" suregrip knob for quick and positive hand tightening. INCLA The INCL is designed to align the templates on a 1-3/4" door with a 2-3/4" backset.the INCLA adapts the INCL to align the templates on a 1-3/8" door and will also align the template with a 2-3/8" backset. Fabricated of quality milled aluminum and designed to fit the INCL precisely. INEXT3 Use with INCL to prep for 3-3/4" backsets. 372
Standard Lock Installation Jig PRO-LOK Boring Jig Cylindrical Lock Installation Jig At last you can have accurate installations the first time, every time! Pro-Lok s new INJIG Boring Jig is an affordable alternative to freehand drilling. Choose your backset and hole size, clamp the jig in place and start drilling. Use the quick-disconnect adapter to release the first bit and engage the second bit... and you re almost finished. Kit includes jig, both 2-1/8" & 1-1/2" cross-bore spur bits, 1" edge-bore bit, strike locator, 3 different latch and faceplate mortise tools, unique deadbolt height gauge and custom molded carrying case. INJIG-100 Maximum Security Mortiser Replacement part for INJIG Tool for mortising the strike plate area for maximum security deadbolt strike plates on wood frames. INJIG-102 Latch Mortiser Replacement part for INJIG Tool for mortising the strike plate area for standard knob & deadbolt strike plates on wood frames. INJIG-104 Full Lip Mortiser Replacement part for INJIG Tool for mortising the strike plate area for Full Lip knob lock strike plates on wood frames. INJIG-106 Quick Change Adapter Replacement part for INJIG This handy tool allows you to quickly unhook from one spur bit on the jig and snap on to the other bit in secondswithout a chuck key. INJIG-108 Lock Jig Replacement part for INJIG The main framework of the jig, this unit supports all of the spur bits and auger bits to clamp on to the door and drill the holes for the lock. INJIG-110 1-1/2" Backup Ring Replacement part for INJIG This ring supports the 1-1/2" spur bit in the main jig to drill the smaller hole required in some deadbolt installations. INJIG-112 Deadbolt Height Gauge Replacement part for INJIG This simple piece snaps into an existing 2-1/8" knob to automatically position the INJIG to drill at either 3-5/8" or 5-1/2" above the knob. INJIG-114 Carrying Case Replacement part for INJIG The molded carrying case holds the entire INJIG assembly and all if its related parts in molded areas and snaps closed for transport & storage. INJIG-116 Strike Locator Replacement part for INJIG After the 1" edgebore hole is drilled, the strike locator is inserted and the door is closed. Pressing outward marks the centerpoint on the frame. INJIG-118 1-1/2" Multi-Spur Bit Replacement part for INJIG This heavy duty multi-spur wood bit is used to drill cross-bore holes for deadbolts requiring the smaller diameter holes on new installations. INJIG-120 2-1/8" Multi-Spur Bit Replacement part for INJIG This heavy duty multi-spur wood bit is used to drill cross-bore holes for locks requiring the standard 2-1/8" size holes on new installations or for replacing locks that used a 1-1/2" on initial installation. INJIG-122 1" Auger Bit Replacement part for INJIG The auger wood bit is used for the 1" edge bore on the door or can removed from the jig and used for hole needed on the frame for the bolt or latch. 373
KD01 Schlage, Kwikset,Weiser,Weslok 655 N Hariton St. Orange CA 92868-1311 (714) 633-0681 KD02 Medeco small pin, Medeco large pin, Master Padlock,American Padlock 655 N Hariton St. Orange CA 92868-1311 (714) 633-0681 KD03 GM, Ford, Chrysler, Ford 10 cut 655 N Hariton St. Orange CA 92868-1311 (714) 633-0681 KD98 ASSA KDIC Stainless Steel key decoder for Best/Falcon & other I/C keys using standard A2 increments. KDSC Stainless Steel key decoder for all Schlage & other (Schlage type) keys using factory increments. 374