CUBE Diode Laser System The Coherent CUBE laser is a compact all-in-one laser system. CUBE lasers offer wavelengths from 75 nm to 70 nm with output power as high as 00 mw. Based on laser diode technologies the CUBE laser offers internal optical, thermal and electronics to create a high-performance high-quality laser beam. CUBE laser come standard as a turn-key system that includes the laser, control box, cables and power supply. Optional heat sink accessory sold separately. The CUBE laser is compatible with the original 00 mm x 40 mm COMPASS laser footprint from Coherent. The CUBE laser has an internal processor to support the USB and RS- interface as well as analog and digital I/O. CUBE lasers offer a wide range of commands and queries to control the laser and report status/diagnostics. FEATURES Compact and modular OEM design Superior beam quality Minimal laser output RMS noise Complete CDRH safety features for scientific and laboratory use TEC temperature-stabilized and conductively cooled through baseplate Analog and digital modulation USB and RS- APPLICATIONS Confocal Microscopy DNA Sequencing Flow Cytometry Medical Imaging and Instrumentation With multiple modulation options the CUBE laser can be operated in a contin-uous-wave (CW) mode, Analog Modulation, and a combined Analog +.
SPECIFICATIONS CUBE CUBE CUBE CUBE CUBE 75-6C 405-50C 405-00C 445-40C 488-50C Part Number 774 7498 479 06948 74040 Wavelength (nm) 75 405 405 445 488 Output Power (mw) 6 50 00 40 50 Beam Diameter at /e (mm) (typical)..4.4.. Beam Divergence (mrad) (typical) 0.5 0.4 0.4 0.6 0.6 M (ModeMaster beam quality) <. <. <. <. <. Beam Asymmetry <:. Laser Drive Modes Digital, Analog and PC Control Maximum Bandwidth (MHz) 50 50 50 5 5 Rise Time (0% to 90%) (nsec) < Fall Time (0% to 90%) (nsec) < < < < < Analog Modulation >,000,000: at 0 Hz, >50: at 50 MHz Maximum Bandwidth (khz) 70 50 50 50 50 Rise or Fall Time (0% to 90%) (μsec) <5 < < < < >0,000: Laser Enable Control Input Maximum Bandwidth (khz) 0 RMS Noise (%), complete On/Off 0 Hz to 0 MHz <0.5 <0. <0. <0. <0. 0 MHz to 500 MHz <.0 Long-Term Power Stability (%) (8 hours) <± Warm-Up Time (minutes) <5 4 5 6 Spatial Mode (far field) TEM 00 Pointing Stability (μrad/ C) <6 Polarization Ratio 4 Min. 00:, Vert. ±5 Static Alignment Tolerances 5 Beam Position (mm) < Beam Angle (mrad) <5 CDRH Laser Classification Class IIIb ESD Protection 6 Level 4 Laser-to-laser tolerance. All lasers ±5 nm except CUBE 640-40 with 65 to 64 nm range, CUBE 640-00 with 65 to 644 nm range, CUBE 647-00 with 646 to 65 nm range, CUBE 660 with 65 to 665 nm range, and CUBE 785 ±0 nm. Output power is variable via RS-, USB or analog interface from % to 00%. Specifications are valid for 00% power. Recommended power range is 70% to 00% power. M and Beam Asymmetry measured with ModeMaster with 90/0 clip levels. Polarization measurement is max./min. power with polarizer at in. from laser with LM- power head at 7 in. from laser. Static alignment tolerances are relative to the right bottom edge (in beam direction). Electro-Static Discharge Standard IEC 6000-4-:008.
SPECIFICATIONS CUBE CUBE CUBE 640-40C 640-00C 647-00C Part Number 06947 5005 9057 Wavelength (nm) 640 640 647 Output Power (mw) 40 00 00 Beam Diameter at /e (mm) (typical).0 Beam Divergence (mrad) (typical).0 M (ModeMaster beam quality) <. Beam Asymmetry <:. Laser Drive Modes Digital, Analog and PC Control Maximum Bandwidth (MHz) 50 Rise Time (0% to 90%) (nsec) < Fall Time (0% to 90%) (nsec) < Analog Modulation >,000,000: at 0 Hz, >50: at 50 MHz Maximum Bandwidth (khz) 50 >0,000: Laser Enable Control Input Maximum Bandwidth (khz) 0 RMS Noise (%), complete On/Off 0 Hz to 0 MHz <0. 0 MHz to 500 MHz <.0 Long-Term Power Stability (%) (8 hours) <± Warm-Up Time (minutes) <5 4 5 6 Spatial Mode (far field) TEM 00 Pointing Stability (μrad/ C) <6 Polarization Ratio 4 Min. 00:, Vert. ±5 Static Alignment Tolerances 5 Beam Position (mm) < Beam Angle (mrad) <5 CDRH Laser Classification Class IIIb ESD Protection 6 Level 4 Laser-to-laser tolerance. All lasers ±5 nm except CUBE 640-40 with 65 to 64 nm range, CUBE 640-00 with 65 to 644 nm range, CUBE 647-00 with 646 to 65 nm range, CUBE 660 with 65 to 665 nm range, and CUBE 785 ±0 nm. Output power is variable via RS-, USB or analog interface from % to 00%. Specifications are valid for 00% power. Recommended power range is 70% to 00% power. M and Beam Asymmetry measured with ModeMaster with 90/0 clip levels. Polarization measurement is max./min. power with polarizer at in. from laser with LM- power head at 7 in. from laser. Static alignment tolerances are relative to the right bottom edge (in beam direction). Electro-Static Discharge Standard IEC 6000-4-:008.
SPECIFICATIONS CUBE CUBE CUBE 660-60C 660-00C 70-0C Part Number 06947 5005 9057 Wavelength (nm) 660 660 70 Output Power (mw) 60 00 0 Beam Diameter at /e (mm) (typical).4.0. Beam Divergence (mrad) (typical) 0.6.0 0.9 M (ModeMaster beam quality) <. Beam Asymmetry <:. Laser Drive Modes Digital, Analog and PC Control Maximum Bandwidth (MHz) 50 Rise Time (0% to 90%) (nsec) < Fall Time (0% to 90%) (nsec) < Analog Modulation >,000,000: at 0 Hz, >50: at 50 MHz Maximum Bandwidth (khz) 50 >0,000: Laser Enable Control Input Maximum Bandwidth (khz) 0 RMS Noise (%), complete On/Off 0 Hz to 0 MHz <0. 0 MHz to 500 MHz <.0 Long-Term Power Stability (%) (8 hours) <± Warm-Up Time (minutes) <5 4 5 6 Spatial Mode (far field) TEM 00 Pointing Stability (μrad/ C) <6 Polarization Ratio 4 Min. 00:, Vert. ±5 Static Alignment Tolerances 5 Beam Position (mm) < Beam Angle (mrad) <5 CDRH Laser Classification Class IIIb ESD Protection 6 Level 4 Laser-to-laser tolerance. All lasers ±5 nm except CUBE 640-40 with 65 to 64 nm range, CUBE 640-00 with 65 to 644 nm range, CUBE 647-00 with 646 to 65 nm range, CUBE 660 with 65 to 665 nm range, and CUBE 785 ±0 nm. Output power is variable via RS-, USB or analog interface from % to 00%. Specifications are valid for 00% power. Recommended power range is 70% to 00% power. M and Beam Asymmetry measured with ModeMaster with 90/0 clip levels. Polarization measurement is max./min. power with polarizer at in. from laser with LM- power head at 7 in. from laser. Static alignment tolerances are relative to the right bottom edge (in beam direction). Electro-Static Discharge Standard IEC 6000-4-:008.
UTILITY AND ENVIRONMENTAL REQUIREMENTS Laser Head Operating Voltage (VDC) +4.8 to 6.5 Laser Head Operating Current (A) <.5 Baseplate Temperature Range +0 to 50 C (50 to F) Max. Heat Dissipation of Head (W) (baseplate at 50 C) Storage Temperature -0 to 60 C (-4 to 40 F) Power Supply (included) Operating Voltage (VDC) 00 to 40, 50 to 60 Hz Power Consumption (W) <5 Dimensions (L x W x H) Weight Laser Head 00 x 40 x 40 mm (.9 x.6 x.6 in.) 0. kg (0.7 lbs.) Control Box 8 x 6 x 6 mm (5.4 x.4 x. in.) 0. kg (0. lbs.) Power Supply 87 x 47 x mm (.4 x.9 x. in.) 0. kg (0.5 lbs.) Head Cable 54 to 406 mm (0 to 8 in.) 0.08 kg (0. lbs.) USB Cable.8m (6 ft.) 0. kg (0. lbs.) Heat Sink (optional) 7 x 66 x 44 mm (5 x.6 x.74 in.) 0.4 kg (0.9 lbs.) Non-condensing with laser diode TEC at set point of C. On-off power switch and LED included in cord to laser head. System includes USA-type power cord, IEC0 input connection.
CUBE ACCESSORIES 07840 CUBE Heat Sink Accessory CUBE heat sink with fan, 7 x 66 x 44 mm 07950 CUBE nd Emission Lamp CDRH lamp for laser emission. Connects to CUBE I/O cable. 0766 *CUBE Interface Cable CUBE to control box, I/O, RS- and power 07454 *CUBE Power Supply, 6 VDC,.5 amps IEC0 input, 0V/0V, switch and LED 08906 *CUBE USB Cable, 6 ft. (.8m) USB standard to mini for CUBE 09966 *Control Box, CDRH, Keyswitch, Interlock Control box for CUBE lasers. Included box, key, interlock RCA and cable. 080090 Cable, Extension, DB-9 M/F, 6 ft. (.8m) Extension cable to extend control box or RS-. M-F, DB-9. 040408 *Plug, RCA Interlock RCA plug for control box, non-shorted 079890 *CUBE Manual and Software** CUBE user manual and software CD for Windows XP*** and Windows 7 (-bit)*** 0806 *Power Cord, USA, 6 ft. (.8m) Power cord, USA plug style to IEC0 6779 CUBE Heat Sink Right Angle CUBE right angle mount, 0 x 47 x 44 mm, same beam position with horizontal polarization * Included at no additional charge with every CUBE system. ** CUBE PC Software only supports Windows OS in -bit for USB. *** Windows XP and Windows 7 are registered trademarks of Microsoft Corporation. MECHANICAL SPECIFICATIONS CUBE Heat Sink Top View in. in. CUBE Alignment Pins PLACES 64 mm (.50 in.) 44. mm (.74 in.) 50 mm in. 66 mm (.60 in.) 7 mm (5.0 in.) enter of Laser eam & Center of Heat Sink 8- Accessory Mounting Holes on 0.5 and in. Centers 4 PLACES 75 mm M4 CUBE Mounting Holes 4 PLACES CUBE Control Box CUBE Power Supply d 6 mm (.0 in.) Analog Control Input BNC Interlock RCA Connection ~80 mm Cord (.0 in.) 86.5 mm (.4 in.) mm (.6 in.) ~.8 m Cord (6 ft.) 6 mm (.4 in.) 8 mm (5.4 in.) 47 mm (.85 in.)
MECHANICAL SPECIFICATIONS CUBE Laser Head Top View 40 mm (.58 in.) 5 mm (0.0 in.) 90 mm (.54 in.) 5 mm (0.0 in.) 0 mm (0.79 in.) 0 mm (.8 in.) 5. mm (0.0 in.) 40 mm (.58 in.) 00 mm (.94 in.) Ø mm (0.8 in.) Dowel Hole Laser Aperture Ø4. mm (0.7 in.) 4 PLACES 6 mm (0.5 in.) SMB USB x 7 mm (0.8 x 0.8 in.) Dowel Slot 9 mm (0.75 in.) 5.5 mm (0.6 in.) DE-5 Coherent, Inc., 500 Patrick Henry Drive Santa Clara, CA 95054 p. (800) 57-786 (408) 764-498 f. (408) 764-4646 tech.sales@coherent.com www.coherent.com ISO 900 Registered Coherent follows a policy of continuous product improvement. Specifications are subject to change without notice. Coherent s scientific and industrial lasers are certified to comply with the Federal Regulations ( CFR Subchapter J) as administered by the Center for Devices and Radiological Health on all systems ordered for shipment after August, 976. Coherent offers a limited warranty for all CUBE lasers. For full details of this warranty coverage, please refer to the Service section at www.coherent.com or contact your local Sales or Service Representative. Printed in the U.S.A. MC-XXX-7-0M7 Copyright 07 Coherent, Inc. LASER RADIATION. AVOID EXPOSURE TO BEAM. CLASS B LASER PRODUCT PER EN6085- (994) 50 to 000 nm <00 mw