0W Constant Current Mode LED Driver IP65 IP67 Ⅰ ~ A File Name:HLG185HCSPEC 160613
0W Constant Current Mode LED Driver SPECIFICATION MODEL HLG185HC500 HLG185HC700 HLG185HC1050 HLG185HC1400 RATED CURRENT RATED POWER 500mA 0W 700mA 0.2W 1050mA 199.5W 1400mA 0.2W CONSTANT CURRENT REGION Note.2 0V ~ 400V 143V ~ 286V 95V ~ 190V 71V ~ 143V Can be adjusted by internal potentiometer (A type only) OUTPUT CURRENT ADJ. RANGE 250 ~ 500mA 350 ~ 700mA 525 ~ 1050mA 700 ~ 1400mA CURRENT RIPPLE 5.0% max. @rated current CURRENT TOLERANCE ±5% SET UP TIME Note.4 1000ms/115VAC 500ms/230VAC VOLTAGE RANGE Note.3 90 ~ 305VAC 127 ~ 431VDC (Please refer to "STATIC CHARACTERISTIC" section) FREQUENCY RANGE POWER FACTOR (Typ.) 47 ~ 63Hz PF 0.9 8/ 115VAC or PF 0.96/230VAC or PF 0.94/2777VAC @ full load (Please refer to " POWER FACTOR (PF) CHARACTERISTIC" section) THD< %@ 50% load/115vac, or 230VAC, or @ 75% load/277vac TOTAL HARMONIC DISTORTION INPUT (Please refer to TOTAL HARMONIC DISTORTION section) EFFICIENCY (Typ.) 94% 94% 94% 94% AC CURRENT (Typ.) 2A / 115VAC 1A / 230VAC 0.85A / 277VAC INRUSH CURRENT(Typ.) MAX. No. of PSUs on 16A CIRCUIT BREAKER COLD START 55A(t width=900 μs measured at 50% I peak) at 230VAC; Per NEMA 410 2 units (circuit breaker of type B) / 3 units (circuit breaker of type C) at 230VAC LEAKAGE CURRENT <0.75mA / 277VAC SHORT CIRCUIT Constant current limiting, recovers automatically after fault condition is removed PROTECTION OVER VOLTAGE 450 ~ 470V 3 ~ 340V 210 ~ 225V 160 ~ 170V Shut down o/p voltage with autorecovery or repower on to recovery OVER TEMPERATURE Shut down o/p voltage, recovers automatically after temperature goes down WORKING TEMP. Tcase=40 ~ 90 (Refer to "Derating Curve") MAX. CASE TEMP. Tcase=90 ENVIRONMENT WORKING HUMIDITY 10 ~ 95% RH noncondensing STORAGE TEMP., HUMIDITY 40 ~ 80, 10 ~ 95% RH TEMP. COEFFICIENT ± 0.03%/ (0 ~ 50 ) VIBRATION 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes SAFETY & EMC OTHERS NOTE SAFETY STANDARDS WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC EMISSION EMC IMMUNITY Note.6 Note.6 UL8750, CSA C22.2 No. 250.1312, ENEC EN613471, EN61347213, EN62384 independent, IP65 or IP67, J613471, J61347213 approved I/PO/P:3.75KVAC I/PFG:2KVAC O/PFG:1.5KVAC I/PO/P, I/PFG, O/PFG:100M Ohms / 500VDC / 25 / 70% RH Compliance to EN55015, EN6100032 Class C ( 50% load) ; EN6100033 Compliance to EN6100042,3,4,5,6,8,11, EN61547, heavy industry level ( surge immunity LineEarth 4KV, LineLine 2KV) MTBF 651.1K hrs min. Telcordia SR332 (Bellcore) ; 191.9K hrs min. MILHDBK217F (25 ) DIMENSION 228*68*38.8mm (L*W*H) PACKING 1.15Kg; 12pcs/14.8Kg/0.8CUFT File Name:HLG185HCSPEC 160613
0W Constant Current Mode LED Driver BLOCK DIAGRAM PFC fosc : 70KHz PWM fosc : 60KHz I/P FG EMI FILTER & RECTIFIERS PFC CIRCUIT O.T.P. O.L.P. POWER SWITCHING PWM & PFC CONTROL RECTIFIERS & FILTER O.L.P. DETECTION CIRCUIT V V DIM DIM (B Type) O.V.P. DRIVING METHODS OF LED MODULE This series works in constant current mode to directly drive the LEDs. 100 Vo(%) Constant Current area In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Should there be any compatibility issues, please contact MEAN WELL. 50 50 100 Io (%) Typical output current normalized by rated current (%) File Name:HLG185HCSPEC 160613
0W Constant Current Mode LED Driver DIMMING OPERATION FG (Green/Yellow) AC/L(Brown) AC/N(Blue) HLG185HC DIM(Blue) DIM(White) V(Black) V(Red) 3 in 1 dimming function (for BType) Output constant current level can be adjusted by applying one of the three methodologies between DIM and DIM: 1 ~ 10VDC, or 10V PWM signal or resistance. Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Dimming source current from power supply: 100μA (typ.) Applying additive 1 ~ 10VDC V V DIM DO NOT connect "DIM to V" Additive Voltage Output current (%) 100% 90% 80% 70% 60% 50% 40% 30% % 10% 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage DIM Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz): V V DIM Additive PWM signal DIM DO NOT connect "DIM to V" Output current (%) 100% 90% 80% 70% 60% 50% 40% 30% % 10% 10% % 30% 40% 50% 60% 70% 80% 90% 100% Duty cycle of additive 10V PWM signal dimming input Applying additive resistance: V V DIM DIM Additive Resistance Output current (%) 100% 90% 80% 70% 60% 50% 40% 30% DO NOT connect "DIM to V" % 10% 10K/N K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N 100K/N (N=driver quantity for synchronized dimming operation) Dimming input: Additive resistance File Name:HLG185HCSPEC 160613
0W Constant Current Mode LED Driver Note: In the case of turning the lighting fixture down to 0% brightness, please refer to the configuration as follow, or please contact MEAN WELL for other options. N FG L Relay Switch Adjuster 10K/N~100K/N Ohms resistance 1~10V DC Voltage 10V PWM Signal Green/ Yellow Brown Blue AC/L AC/N HLG185HC BType DIM DIM V() V() Blue White Black Red LED Lighting Fixture Using a switch and relay can turn ON/OFF the lighting fixture. File Name:HLG185HCSPEC 160613
0W Constant Current Mode LED Driver OUTPUT LOAD vs TEMPERATURE 100 100 80 C1400 Others 80 C1400 Others 60 60 LOAD (%) 40 LOAD (%) 40 40 10 0 15 30 50 60 70 (HORIZONTAL) 40 0 45 55 65 75 90(HORIZONTAL) AMBIENT TEMPERATURE,Ta ( ) Tcase ( ) STATIC CHARACTERISTIC POWER FACTOR (PF) CHARACTERISTIC Tcase at 80 100 1 90 0.98 80 0.96 LOAD (%) 70 60 50 40 90 100 125 135 145 155 165 175 180 0 230 305 INPUT VOLTAGE (V) 60Hz PF 0.94 0.92 0.9 0.88 0.86 50% 60% 70% 80% 90% 100% (0W) (250W) LOAD 277V 230V 115V TOTAL HARMONIC DISTORTION (THD) 700mA Model, Tcase at 80 25 EFFICIENCY vs LOAD possess superior working efficiency that up to 94% can be reached in field applications. 700mA Model, Tcase at 80 95 93 THD(%) 15 10 5 277VAC 230VAC 115VAC EFFICIENCY(%) 91 89 87 85 83 81 277V 230V 115V 0 50% 60% 70% 80% 90% 100% 79 77 10% % 30% 40% 50% 60% 70% 80% 90% 100% LOAD LOAD File Name:HLG185HCSPEC 160613
0W Constant Current Mode LED Driver LIFE TIME 1 100 80 LIFETIME(Kh) 60 40 0 30 40 50 60 70 80 90 Tc a s e ( ) File Name:HLG185HCSPEC 160613
0W Constant Current Mode LED Driver MECHANICAL SPECIFICATION Case No.994D Unit:mm AType 12 9.6 228 4 FG (Green/Yellow) AC/L(Brown) AC/N(Blue) 3C 9.4 34.2 9.4 68 34 tc 102 Io ADJ. STW 16AWG 2C(for HLG185HC500) 2C(for others) ψ 4.2 4PL V(Black) V(Red) tc : Max. Case Temperature 38.8 BType 12 228 4 FG (Green/Yellow) AC/L(Brown) AC/N(Blue) 3C 9.6 9.4 34.2 9.4 68 34 tc 102 2C STW 16AWG 2C(for HLG185HC500) 2C(for others) ψ 4.2 4PL DIM(Blue) DIM(White) V(Black) V(Red) tc 38.8 : Max. Case Temperature DType 12 9.6 228 4 FG (Green/Yellow) AC/L(Brown) AC/N(Blue) 3C 9.4 34.2 9.4 68 Tcase tc 38.8 34 tc : Max. Case Temperature 102 STW 16AWG 2C(for HLG185HC500) 2C(for others) ψ 4.2 4PL V(Black) V(Red) File Name:HLG185HCSPEC 160613
0W Constant Current Mode LED Driver WATERPROOF CONNECTION Waterproof connector Waterproof connector can be assembled on the output cable of HLG185HC to operate in dry/wet/damp or outdoor environment. AC source I/P HLG185HC O/P Size Pin Configuration (Female) Size Pin Configuration (Female) M12 Order No. Suitable Current 4PIN 5A/PIN M1204 10A max. 5PIN 5A/PIN M1205 10A max. M15 Order No. Suitable Current 2PIN 12A/PIN M1502 12A max. LED Lamp Cable Joiner 66 26 CJ041 suitable for 14AWG~16AWG CJ042 suitable for 18AWG~22AWG ψ25 Up to four wires can be connected through this cable joiner by soldering or clamping by tools. LED Lamp HLG185HC O/P Wires CJ04 cable joiner can be purchased independently for user's own assembly. MEAN WELL order No. : CJ041, CJ042. INSTALLATION MANUAL Please refer to : http://www.meanwell.com/webnet/search/installationsearch.html File Name:HLG185HCSPEC 160613
Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Mean Well: HLG185HC1400A HLG185HC500B HLG185HC1050A HLG185HC700B HLG185HC700A HLG185H C1050B HLG185HC500A HLG185HC1400B