IP65 IP67 S&E Ⅰ ~ A File Name:HLG60HCSPEC 180110
SPECIFICATION MODEL OUTPUT INPUT PROTECTION SAFETY & EMC OTHERS NOTE RATED CURRENT RATED POWER CONSTANT CURRENT REGION Note.2 CURRENT ADJ. RANGE CURRENT RIPPLE CURRENT TOLERANCE SET UP TIME FREQUENCY RANGE EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT(Typ.) MAX. No. of PSUs on 16A CIRCUIT BREAKER LEAKAGE CURRENT SHORT CIRCUIT OVER VOLTAGE OVER TEMPERATURE SAFETY STANDARDS WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC EMISSION Note.4 VOLTAGE RANGE Note.3 POWER FACTOR (Typ.) TOTAL HARMONIC DISTORTION Adjustable for AType only (via builtin potentiometer) 210 ~ 350mA 4 ~ 700mA 5.0% max. @rated current ±5% 750ms/115VAC, 500ms/230VAC 47 ~ 63Hz PF 0.9 8/ 115VAC, PF 0.96/230 VAC, PF 0.94/277VAC @ full load (Please refer to " POWER FACTOR (PF) CHARACTERISTIC" section) <0.75mA / 277VAC Shut down o/p voltage with autorecovery or repower on to recovery Shut down o/p voltage, repower on to recover UL8750, CSA C22.2 No. 250.008, EN/AS/NZS 613471,EN/AS/NZS 61347213 independent, GB19510.1,GB19510.14, Note.6 EAC TP TC 004,IP65 or IP67, J613471,J61347213 approved Note.6 HLG60HC350 90 ~ 305VAC 127 ~ 431VDC (Please refer to "STATIC CHARACTERISTIC" section) THD< % (@ load 60% /115VAC, 230VAC; @ load 75%/277VAC) (Please refer to TOTAL HARMONIC DISTORTION (THD) section) HLG60HC700 350mA 700mA 70W 70W ~ 0V 50 ~ V 91% 90.5% 0.69A / 115VAC 0.35A / 230VAC 0.29A / 277VAC COLD START 60A(t width=275 μs measured at 50% I peak) at 230VAC; Per NEMA 410 8 units (circuit breaker of type B) / 13 units (circuit breaker of type C) at 230VAC Hiccup mode, recovers automatically after fault condition is removed 230 ~ 250V 1 ~ 1V WORKING TEMP. Tcase= ~ 80 (Please refer to "OUTPUT LOAD vs TEMPERATURE" section) MAX. CASE TEMP. Tcase=80 ENVIRONMENT WORKING HUMIDITY 10 ~ 95% RH noncondensing STORAGE TEMP., HUMIDITY ~ 80, 10 ~ 95% RH TEMP. COEFFICIENT VIBRATION ± 0.03%/ (0 ~ 50 ) 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes I/PO/P:3.75KVAC I/PFG:2KVAC O/PFG:1.5KVAC I/PO/P, I/PFG, O/PFG:M Ohms / 500VDC / 25 / 70% RH Compliance to EN55015, EN6032 Class C (@ load 60% ) ; EN6033,GB17743 and GB17625.1, EAC TP TC 0 EMC IMMUNITY Compliance to EN6042,3,4,5,6,8,11, EN61547, heavy industry level (surge immunity LineEarth 4KV, LineLine 2KV), EAC TP TC 0 MTBF 878.1K hrs min. Telcordia SR332 (Bellcore) ; 338K hrs min. MILHDBK217F (25 ) DIMENSION 171*61.5*36.8 mm (L*W*H) PACKING 0.73Kg; pcs/15.6kg/0.9cuft File Name:HLG60HCSPEC 180110
BLOCK DIAGRAM PFC fosc : 60KHz PWM fosc : 80KHz I/P FG EMI FILTER & RECTIFIERS PFC CIRCUIT O.T.P. O.L.P. POWER SWITCHING PWM & PFC CONTROL RECTIFIERS & FILTER O.L.P. DETECTION CIRCUIT V V DIM DIM (B Type) O.V.P. DRIVING METHODS OF LED MODULE This series works in constant current mode to directly drive the LEDs. Vo(%) (A) Constant Current area In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Should there be any compatibility issues, please contact MEAN WELL. 50 (min.) (B) Hiccup Protection 50 Io (%) Typical output current normalized by rated current (%) File Name:HLG60HCSPEC 180110
DIMMING OPERATION AC/L(Brown) AC/N(Blue) FG (Green/Yellow) HLG60HC V(Brown) V(Blue) DIM(Gray) DIM(Black) 3 in 1 dimming function (for BType) Output constant current level can be adjusted by applying one of the three methodologies between DIM and DIM: 1 ~ 10VDC, or 10V PWM signal or resistance. Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Dimming source current from power supply: μa (typ.) Applying additive 1 ~ 10VDC V V DIM DO NOT connect "DIM to V" Additive Voltage Output current (%) % 90% 80% 70% 60% 50% % 30% % 10% 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage Output current (%) % 90% 80% 70% 60% 50% % 30% % 10% 10% % 30% % 50% 60% 70% 80% 90% % Duty cycle of additive 10V PWM signal dimming input DIM Applying additive 10V PWM signal (frequency range Hz ~ 3KHz): V V DIM Additive PWM signal DIM DO NOT connect "DIM to V" Applying additive resistance: V V DIM Additive Resistance DIM DO NOT connect "DIM to V" Output current (%) % 90% 80% 70% 60% 50% % 30% % 10% 10K/N K/N 30K/N K/N 50K/N 60K/N 70K/N 80K/N 90K/N K/N (N=driver quantity for synchronized dimming operation) Dimming input: Additive resistance File Name:HLG60HCSPEC 180110
Note: In the case of turning the lighting fixture down to 0% brightness, please refer to the configuration as follow, or please contact MEAN WELL for other options. N FG L Relay Swih Adjuster 10K/N~K/N Ohms resistance 1~10V DC Voltage 10V PWM Signal Green/ Yellow Brown Blue AC/L AC/N HLG60HC BType DIM DIM V() V() Gray Black Blue Brown LED Lighting Fixture Using a swih and relay can turn ON/OFF the lighting fixture. File Name:HLG60HCSPEC 180110
OUTPUT LOAD vs TEMPERATURE 80 80 60 60 LOAD (%) LOAD (%) AMBIENT TEMPERATURE,Ta ( ) Tcase ( ) STATIC CHARACTERISTIC 90 80 70 60 50 25 10 0 15 30 50 60 70 90 125 135 145 155 165 175 180 0 230 305 INPUT VOLTAGE (V) 60Hz (HORIZONTAL) LOAD (%) PF 1.02 1 0.98 0.96 0.94 0.92 0.9 0.88 0.86 0.84 25 0 30 50 70 80 (HORIZONTAL) POWER FACTOR (PF) CHARACTERISTIC Tcase at 70 50% 60% 70% 80% 90% % (70W) LOAD 277V 230V 115V TOTAL HARMONIC DISTORTION (THD) 350mA Model, Tcase at 70 EFFICIENCY vs LOAD possess superior working efficiency that up to 91% can be reached in field applications. 350mA Model, Tcase at 70 THD(%) 35 30 25 15 10 5 0 50% 60% 70% 80% 90% % 277VAC 230VAC 115VAC EFFICIENCY(%) % 90% 80% 70% 60% 50% % 30% % 10% 0% 10% % 30% % 50% 60% 70% 80% 90% % 277V 230V 115V LOAD LOAD File Name:HLG60HCSPEC 180110
LIFE TIME 1 LIFETIME(Kh) 80 60 0 30 50 60 70 80 Tc a s e ( ) File Name:HLG60HCSPEC 180110
MECHANICAL SPECIFICATION AType Case No.957 Unit:mm 171 11.9 147.2 9.6 AC/L(Brown) 73.6 AC/N(Blue) FG (Green/Yellow) SJOW 17AWG& H05RN F 1. 0mm 2 3C Io SJOW 17AWG & H05RN F 1. 0mm 2C ADJ 32 46.5 61.5 30.75 ψ 4.2 4PL V(Brown) V(Blue) 2 : Max. Case Temperature 36.8 BType 171 11.9 147.2 9.6 AC/L(Brown) AC/N(Blue) FG (Green/Yellow) SJOW 17AWG& H05RN F 1. 0mm 2 3C 32 46.5 61.5 30.75 36.8 73.6 SJOW 17AWG& H05RN F 1. 0mm 2 2C SJOW 17AWG& H05RN F 1. 0mm 2 2C ψ 4.2 4PL V(Brown) V(Blue) DIM(Gray) DIM(Black) : Max. Case Temperature DType 171 11.9 147.2 9.6 AC/L(Brown) 73.6 V(Brown) AC/N(Blue) FG (Green/Yellow) SJOW 17AWG& H05RN F 1. 0mm 2 3C SJOW 17AWG & H05RN F 1. 0mm 2 2C V(Blue) 32 46.5 61.5 ψ 4.2 4PL 36.8 30.75 : Max. Case Temperature File Name:HLG60HCSPEC 180110
WATERPROOF CONNECTION Waterproof connector Waterproof connector can be assembled on the output cable of HLG60HC to operate in dry/wet/damp or outdoor environment. AC source I/P HLG60HC O/P Size Pin Configuration (Female) Size Pin Configuration (Female) M12 Order No. Suitable Current 4PIN 5A/PIN M1204 10A max. 5PIN 5A/PIN M1205 10A max. M15 Order No. Suitable Current 2PIN 12A/PIN M1502 12A max. LED Lamp Cable Joiner 66 26 CJ041 suitable for 14AWG~16AWG CJ042 suitable for 18AWG~22AWG ψ25 Up to four wires can be connected through this cable joiner by soldering or clamping by tools. LED Lamp HLG60HC O/P Wires CJ04 cable joiner can be purchased independently for user's own assembly. MEAN WELL order No. : CJ041, CJ042. INSTALLATION MANUAL Please refer to : http://www.meanwell.com/manual.html File Name:HLG60HCSPEC 180110