1 Double Wedding Ring Table Runner Finished Size 17½ x 46 This table runner is made with 5 inch blocks and one single piece of fabric as the rings, unlike the Double Wedding Ring quilt, which is made from striped pieced fabrics done before making the block.
2 Double Wedding Ring Table Runner Finished Size 17½ x 46 Fabric Requirements: Supplies: Background: 1 1/4 yards Battilizer - 5 yard package Backing: 1 yard Trimmer By George 2.0 Ring Fabric: 3/4 yard HoopScissors Mini Binding: 1/3 yard VanishLite Water Soluble Thread Embroidery threads to match your background and ring fabrics Cutting Chart Background Fabric Cut 16 7½ x 7½ Cut 20 7½ x 6 Cut 4 6 x 6 Backing Fabric Cut 16 6 x 6 Cut 20 6 x 5 Cut 4 4½ x 4½ Ring Fabric Cut 16 6 x 6 Binding Fabric Cut 4 2½ x Width of Fabric
3 Main Double Wedding Ring Block - Stitch 16 for Runner in 5 inch size 1.) Hoop Battilizer. Place neutral embroidery thread in the needle and embroidery bobbin thread in the bobbin and sew the pattern onto the Battilizer 2.) Place water soluble thread in the needle only. Place Backing Fabric 2 on the back of the hoop. Place Background Fabric 1 on the top of the hoop. Sew outline and placement stitches. 3.) Place Thread A in the needle and bobbin and stitch embroidery. NOTE: Make sure to do a needle down, needle up to bring your bobbin thread to the top before stitching the embroidery. 4.) Still using Thread A in the needle and bobbin, Place Ring Fabric, centering over placement stitches. Sew tack down. Cut small slit (see X). Trim up to stitching inside and outside rings. Keep center section for Border blocks. x 5.) Place Thread B in the needle and bobbin and stitch the quilting and deco stitch. 6.) Place Thread A in the needle and bobbin and stitch satin stitches. 7.) Place Thread B in the needle and bobbin and stitch quilting. 8.) Place water soluble thread in the needle and neutral embroidery thread in the bobbin and stitch basting stitch. This is the stitching you will put the edge of the Trimmer By George 2.0 against to trim block.
4 Main Double Wedding Ring Block Block Trimming Instructions Trim the backing and Battilizer up to the basting stitch using the Trimmer By George 2.0. Cut fabric on front of block 3/4 from the basting stitch. You will use the no sash method for joining the blocks. See Joining Slideshow.
5 Double Wedding Ring Border Blocks - Stitch 10 Block A, and 10 Block B for Runner in 5 inch size 1.) Hoop Battilizer. Place the neutral embroidery thread in the needle and embroidery bobbin thread in the bobbin and sew the pattern onto the Battilizer 2.) Place water soluble thread in the needle only. Place Backing Fabric 2 on the back of the hoop. Place Background Fabric 1 on the top of the hoop. Sew outline and placement stitches. 3.) Place fabric from center of main block over placement stitches. Sew tack down stitches. Trim close to stitching. 4.) Place Thread B in the needle and bobbin and stitch the quilting and deco stitch. 5.) Place Thread A in the needle and bobbin and stitch satin stitches. 6.) Place Thread B in the needle and bobbin and stitch quilting. A B 7.) Place Thread A in the needle and bobbin and stitch embroidery. A B 8.) Place water soluble thread in the needle and neutral embroidery thread in the bobbin and stitch basting stitch. This is the stitching you will put the edge of the Trimmer By George 2.0 against to trim block.
6 Double Wedding Ring Border Blocks Double Wedding Ring Border Block Block Trimming Instructions Cut the side marked in red that will have binding attached to it 1/4 through all layers. For the other three sides, trim the backing and Battilizer up to the basting stitch using the Trimmer By George 2.0. Cut fabric on front of block 3/4 from the basting stitch. You will use the no sash method for joining the blocks. See Joining Slideshow. A B
7 Double Wedding Ring Corner Block - Stitch 4 for Runner in 5 inch size 1.) Hoop Battilizer. Place the neutral embroidery thread in the needle and embroidery bobbin thread in the bobbin and sew the pattern onto the Battilizer 2.) Place Water soluble thread in the needle only. Place Backing Fabric 2 on the back of the hoop. Place Background Fabric 1 on the top of the hoop. Sew basting stitch. 3.) Place Thread B in the needle and bobbin and stitch quilting. 4.) Place Water soluble thread in the needle and embroidery bobbin thread in the bobbin and stitch basting stitch. This is the stitching you will put the edge of the Trimmer By George 2.0 against to trim block. Double Wedding Ring Corner Block Block Trimming Instructions Cut the two sides marked in red that will have binding attached to it 1/4 through all layers. For the remaining two sides, trim the backing and Battilizer up to the basting stitch using the Trimmer By George 2.0. Cut fabric on front of block 3/4 from the basting stitch. You will use the no sash method for joining the blocks. See Joining Slideshow.