Transform your space into an extraordinarily inviting home, office or gathering place with the versatile, powerful and elegant Olin Fixture system.

OLIN FIXTURES

Transform your space into an extraordinarily inviting home, office or gathering place with the versatile, powerful and elegant Olin Fixture system. This new Trulux collection introduces a sleek minimalistic look of the Olin profile as the basis for building your own wall sconces and coordinating suspended linear pendant fixtures.

OLIN WALL SCONCE KITS (1M / 2M) Available in 1 meter and 2 meter versions, these sleek wall sconce kits include 3000K Warm White dimmable tape light, dimmable driver and all the installation hardware needed to make vertical Olin sconces. Simply cut the Olin extrusion and Trulux Spec Grade Tape Light to the desired height to create your own custom Olin Sconce. Sleek aluminum fixture housing is a robust heat sink for Trulux tape Conductive end caps allow 360º adjustment, then lock into place for either direct or indirect lighting effects Conductive support rod is made of brass with matte chrome plating (rod must be cut to size, 6 maximum extension from wall recommended) Wall canopies are minimalistic and sleek with a locking cam design for secure positioning For more information on installation, please see pages (16-19) 1 Meter OLIN Sconce (OLIN-SCONCE-1M) 2 Meter OLIN Sconce (OLIN-SCONCE-2M) Conductive Rod Conductive Wall Mount 1M-2M OLIN Extrusion Trulux Spec Grade 3000K Tape Light 1M-2M Frosted Lens 0.61 8 MAX 0.84 4

OLIN PENDANT KITS (1M / 2M) Suspended pendant kits have everything you need to make your own slim, attractive and chic light fixtures, including Spec Grade 3000K Warm White dimmable tape light and a dimming driver sized specifically for each kit. Cut the extrusion and included Trulux tape light to create custom lengths. Sleek extruded aluminum Olin housing with supports and conductive ends make a clean unobtrusive pendant fixture with a wide 120º distribution Kits include stainless steel suspension cables, 6 feet in length, to accommodate high ceilings and staggered mounting heights 1M kits are versatile and practical with conductive swivel end caps - ideal for making suspended, custom length directional lighting 1-1/8 diameter brushed steel ceiling canopies and support clips maintain the minimal look while providing a reliable cable support, while matching conductive ends invisibly power the tape light Spec Grade Trulux tape light with 0.31 LED spacing eliminate hot spots or dotting for a continuous uniform lens appearance For more information on installation, please see pages (12-15) 1 Meter OLIN Pendant (OLIN-SUSP-1M) 2 Meter OLIN Pendant (OLIN-SUSP-2M) Conductive Ceiling Mount Conductive Ceiling Mount Non-Conductive Ceiling Mount 0.84 Conductive Cable - 6ft 6 Conductive End Cap Conductive End Cap Non-Conductive Support Clip 0.61 1M OLIN Extrusion Trulux Spec Grade 3000K Tape Light 1M Frosted Lens 2M OLIN Extrusion Trulux Spec Grade 3000K Tape Light 2M Frosted Lens 6

OLIN PENDANT KIT (3M) For larger spaces, such as islands in big kitchens, conference rooms and reception areas, use OLIN-SUSP-3M pendant kit for fixtures up to 10 feet in length. Spec Grade 3000K Warm White dimmable tape light and a dimming driver sized for this length is included with each kit. Sleek extruded aluminum Olin housing with supports and conductive ends make a sleek, yet powerful pendant fixture with a wide 120º distribution Kits include stainless steel suspension cables, each 6 feet in length, to accommodate high ceilings and staggered mounting heights (shown at right) 3M kits include four supports, two of which you make conductive so that the cable becomes a positive or negative lead (see drawing below) 1-1/8 diameter brushed steel ceiling canopies and support clips maintain the minimal look while matching conductive ends invisibly power the tape light Spec Grade Trulux tape light with 0.31 LED spacing eliminate hot spots or dotting for a continuously uniform lens appearance For more information on installation, please see pages (12-15) 1 Meter OLIN Pendant (OLIN-SUSP-3M) Conductive Ceiling Mount Non-Conductive Ceiling Mounts 0.84 Conductive Cable - 6ft 6 Conductive End Cap Non-Conductive Support Clips 0.61 3M OLIN Extrusion Trulux Spec Grade 3000K Tape Light 3M Frosted Lens 8

OLIN FIXTURE KITS / COMPONENT LIST EACH FIXTURE KIT is comprised of all you will need to make suspended pendants or wall sconces, including 13.1 feet of Spec Grade Trulux Tape Light and a dimming driver sized specifically for the length of Olin fixture. TRULUX TAPE LIGHT is at the heart of the Olin Fixture series. Spec Grade Trulux Tape has 0.31 LED spacing, so that you see an attractive continuous line of light. 3000K Warm White is standard. Dimming drivers are included and sized specifically for each kit. Spec Grade Trulux Tape is cuttable every 1.97 for maximum precision. ELV DIMMING DRIVERS allow you to control the light output for different occasions and ambiance. They are forward phase, reverse phase and triac compatible, so you can use virtually any dimmer you want. 1M OLIN Sconce (OLIN-SCONCE-1M) (2) - Conductive Wall Mounts (1) - 1M Conductive Rod (2) - Conductive End Caps (1) - 1M OLIN Extrusion (1) - 1M Frosted UV Lens (1) - 13ft Spec Grade 3000K Tape Light (1) - 24V / 30W Dimmable Driver 2M OLIN Sconce (OLIN-SCONCE-2M) (2) - Conductive Wall Mounts (1) - 1M Conductive Rod (2) - Conductive End Caps (1) - 2M OLIN Extrusion (1) - 2M Frosted UV Lens (1) - 13ft Spec Grade 3000K Tape Light (1) - 24V / 45W Dimmable Driver (PE-SUSP-CMT) (PE-ROD-1M) (PE-OLIN-PWR-END) (PE-OLIN-1M) (PE-UVLENS-1M) (SPTL-WW-13) (ELV-30-24) (PE-SUSP-CMT) (PE-ROD-1M) (PE-OLIN-PWR-END) (PE-OLIN-2M) (PE-UVLENS-2M) (SPTL-WW-13) (ELV-45-24) 1M OLIN Pendant (OLIN-SUSP-1M) (2) - Conductive Ceiling Mounts (2) - 6ft Conductive Cable (2) - Conductive End Caps (1) - 1M OLIN Extrusion (1) - 1M Frosted UV Lens (1) - 13ft Spec Grade 3000K Tape Light (1) - 24V / 30W Dimmable Driver 2M OLIN Pendant (OLIN-SUSP-2M) (3) - Conductive Ceiling Mounts (3) - 6ft Conductive Cable (2) - Conductive End Caps (1) - Center Support Clip (1) - 2M OLIN Extrusion (1) - 2M Frosted UV Lens (1) - 13ft Spec Grade 3000K Tape Light (1) - 24V / 45W Dimmable Driver 3M OLIN Pendant (OLIN-SUSP-3M) (4) - Conductive Ceiling Mounts (4) - 6ft Conductive Cable (2) - Conductive End Caps (2) - Center Support Clips (1) - 3M OLIN Extrusion (1) - 3M Frosted UV Lens (1) - 13ft Spec Grade 3000K Tape Light (1) - 24V / 80W Dimmable Driver (PE-SUSP-CMT) (PE-SUSP-6) (PE-OLIN-PWR-END) (PE-OLIN-1M) (PE-UVLENS-1M) (SPTL-WW-13) (ELV-30-24) (PE-SUSP-CMT) (PE-SUSP-6) (PE-OLIN-PWR-END) (PE-SUSP-CC) (PE-OLIN-2M) (PE-UVLENS-2M) (SPTL-WW-13) (ELV-45-24) (PE-SUSP-CMT) (PE-SUSP-6) (PE-OLIN-PWR-END) (PE-SUSP-CC) (PE-OLIN-3M) (PE-UVLENS-3M) (SPTL-WW-13) (ELV-80J-24) 10

KIT COMPONENTS & ADDITIONAL ACCESSORIES Each element of the Olin Fixture kit is engineered for performance and aesthetics. See below for a detailed view of each component and its corresponding part number. Each is sold separately if you want to build fixtures with any remaining materials from an Olin kit. OLIN EXTRUSION OLIN LENS CEILING / WALL MOUNT - 24V CONDUCTIVE CABLE - 24V CONDUCTIVE ROD - 24V PE-OLIN-1M PE-OLIN-2M PE-OLIN-3M (1M Extrusion) (2M Extrusion) (3M Extrusion) PE-UVLENS-1M PE-UVLENS-2M PE-UVLENS-3M (1M Lens) (2M Lens) (3M Lens) PE-SUSP-CMT PE-SUSP-6 PE-ROD-1M SUPPORT CLIP - 24V CONDUCTIVE END CAP - 24V OLIN END CAP TRULUX SPEC GRADE TAPE - 24V DIMMABLE DRIVERS - 24V PE-SUSP-CC PE-OLIN-PWR-END PE-OLIN-END SPTL-WW-13 (13.1 ft / 3000K) ELV-30-24 ELV-45-24 ELV-80J-24 (18-30W max) (27-45W max) (48-80W max) 11

ASSEMBLING & INSTALLING OLIN PENDANTS Trulux Olin fixtures are recommended for new construction installation, or when adequate space is available for direct access above desired mounting location. Olin pendant kits may be suspended from traditional drywall and drop-down panel ceilings. Power supplies must be installed in a remote location in certified housings or junction boxes. Tools & materials required for Installation Utility Knife Soldering Iron / Soldering Wire Cable Cutter (Dikes) 22-Gauge Electrical Wire Wire Strippers Power Drill Straight-Cut Tin Snips (5/32) & (23/64) Drill Bits Miter Saw / Hacksaw Phillips Head Screwdriver (2.5mm) & (3mm) Allen Key STEP 1 - Determine Pendant Length Available in 1M, 2M, and 3M sizes, Olin Pendant kits may be cut to custom lengths. When doing so, take into consideration of cuttable areas on Trulux Spec Grade tape light (every 1.97 ). To fully optimize use of tape light and to reduce any gapping, (5/8 ) spacing is required on both ends the of extrusion for soldering tape light connections. STEP 2 - Cutting Tape Light & Extrusion Once the length of the pendant has been determined, begin by cutting the tape light to the appropriate length for the size of fixture. The tape light must be cut on the indicated cutting increments while factoring additional (5/8 ) spacing needed on both ends for soldering. The Olin extrusion will also need to be cut down to size using either a miter saw or hacksaw. When using a miter saw, slowly cut the extrusion to avoid any chipping and let the saw blade come to a complete stop prior to lifting the saw blade. Doing so will result in a much cleaner extrusion edge. Recommended cutting increments for each Olin pendant kit sizes as follows: 1M Olin Pendant: 37-3/8 - Spec Grade Tape Light 38-5/8 - Olin Extrusion 2M Olin Pendant: 76-3/4 - Spec Grade Tape Light 78 - Olin Extrusion 3M Olin Pendant: 117-3/8 - Spec Grade Tape Light 118-3/8 - Olin Extrusion 12

STEP 3 - Prep the Tape Light for Installation Before applying the tape light into the extrusion, you will need to remove a light film from the conductive points on both ends of the tape light. Using the point of a utility knife, lightly scuff the positive (+24V DC) and negative (-) tabs on the tape light to ensure conductivity for soldering power feeds. STEP 7 - Cut and Install Lens Cover Measure the inner dimensions of the extrusion from one end cap to the other for the length of lens cover needed. Cut the lens by using a pair of straight-cut tin snips ensuring a clean cut. Once cut to size, snap one end of the lens and continue to press in the lens as you work towards the opposite end. STEP 5 - Solder Power Feeds Start by cutting two pieces of power feed wire to about (1 ) long and strip both positive and negative wire ends. Solder the positive wire to the (+24V DC) tab on one side of the tape, and the negative wire to the (-) tab marked on the opposite end of the tape light. STEP 8 - Measure Pendant for Ceiling Mount Spacing Once the Olin Pendant has been assembled, you will need to measure the overall mounting length. Measure eyelet to eyelet on the conductive end caps as this will be the spacing for installing the conductive ceiling mounts and where the fixture will hang. Conductive Ceiling Mounts (Pendant Length) STEP 4 - Install Tape Light Install the tape light by peeling the backing film and placing within the Olin extrusion. Start the run of tape light (5/8 ) from one end of the Olin extrusion. There should be a (5/8 ) gap on the opposite end of the extrusion once tape light is fully installed. This will allow proper spacing for the conductive end caps to be soldered to the tape light. STEP 6 - Solder Conductive End Caps Using the supplied conductive end caps (PE-OLIN-PWR-END), firmly press both end caps into Olin extrusion and solder the feed wires to the conductive tabs on both end caps. STEP 9 - Install Drywall Anchors Mark the location for the conductive ceiling mounts with the measurement from Step 8. Begin by drilling a (23/64) hole and Install the supplied drywall anchor and anchor bolt. Compress the drywall anchor by tightening the anchor bolt clockwise. This can be done with a power drill or standard screwdriver. Do not over tighten the anchor as it may damage the drywall. Once fully compressed or tightened, remove anchor bolt and discard. Repeat this process for any additional ceiling mounts needed. Continue to next page... 13

ASSEMBLING & INSTALLING OLIN PENDANTS CONTINUED STEP 10 - Connect Power Wires to Ceiling Mounts 24V power wire must be run to install location for both positive (+24V DC) and negative (-) conductive mounts. Drill a (5/32) pilot hole and feed power wire through the wall. Drill the pilot hole as close as possible to the drywall anchor to ensure a covered finish. Once the power wires have been fed through the pilot hole, crimp the wire to the conductive tab. We recommended that this connection be soldered as well to ensure connection. STEP 13 - Prepping Support Clips (2M & 3M Pendants Only) Our support clips come as a conductive support clip for custom installations when conductive end caps wont be used. However, for this installation we will need to remove the conductive tab. Start by unscrewing the stem from the clip itself. Remove only the conductive tab and place the stem back onto the clip and hand tighten. Do not over tighten as the screw may break. STEP 11 - Install Ceiling Mounts For the conductive ceiling mounts, place the conductive tab over the stem bolt and position the bolt so that the crimped tab will recess into the power feed hole in the drywall. Repeat this process for all conductive ceiling mounts. To install conductive and non-conductive ceiling mounts, tighten the stem bolt by hand until fully flush to the drywall. STEP 14 - Adding Support Clips (2M & 3M Pendants Only) For 2M & 3M pendants, additional support clips and ceiling mounts are required and must be spaced every 1M for applications longer than 2M. To install the support clip, simply clip on the support clip to the extrusion at the required spacing increments. Non-Conductive Ceiling Mount Non-Conductive Support Clip STEP 12 - Install Support Cable Using the supplied conductive cable (PE-SUSP-6), secure one end of the cable into each ceiling mount by tightening the set screw with a (3mm) allen key. Repeat process for all ceiling mounts. Support cable comes in (6ft) lengths and may be cut to size. Use a pair of cable cutters (Dikes) to cut support cable. (1M) STEP 15 - Suspend the Fixture (2M) Begin suspending the fixture by feeding the suspended cable into one end of the fixtures conductive end cap. Tighten set screw using a (2.5mm) allen key and repeat this process for opposite end cap. Tighten support clip set screw using a (3mm) allen key and repeat process for any additional support clips. 14

INSTALLATION NOTES 15

ASSEMBLING & INSTALLING OLIN SCONCES Trulux Olin fixtures are recommended for new construction installation, or when adequate space is available for direct access above behind mounting location. Olin Sconce kits may be mounted to traditional drywall and/or similar substrates. Power supplies must be installed in a remote location in certified housings or junction boxes. Tools & materials required for Installation Utility Knife Soldering Iron / Soldering Wire Cable Cutter (Dikes) 22-Gauge Electrical Wire Wire Strippers Power Drill Straight-Cut Tin Snips (5/32) & (23/64) Drill Bits Miter Saw / Hacksaw Phillips Head Screwdriver (2.5mm) & (3mm) Allen Key STEP 1 - Determine Sconce Length Determine sconce length desired - available in 1M, and 2M sizes. Olin sconce kits may be cut to custom lengths. When doing so, take into consideration of cuttable areas on Trulux Spec Grade tape light (every 1.97 ). To fully optimize use of tape light and to reduce any gapping, (5/8 ) spacing is required on both ends the of extrusion for soldering tape light connections. STEP 2 - Cutting Tape Light & Extrusion Once the length of the sconce has been determined, begin by cutting the tape light to the appropriate length for the size of fixture. The tape light must be cut on the indicated cutting increments while factoring additional (5/8 ) spacing needed on both ends for soldering. The Olin extrusion will also need to be cut down to size for best results. Recommended cutting increments for each Olin sconce kit size as follows: 1M Olin Sconce: 37-3/8 - Spec Grade Tape Light 38-5/8 - Olin Extrusion 2M Olin Sconce: 76-3/4 - Spec Grade Tape Light 78 - Olin Extrusion 16

STEP 3 - Prepping the Tape Light for Installation Before applying the tape light into the extrusion, you will need to remove a light film from the conductive points on both ends of the tape light. Using the point of a utility knife, lightly scuff the positive (+24V DC) and negative (-) tabs on the tape light to ensure conductivity for soldering power feeds. STEP 7 - Cut and Install Lens Cover Measure the inner dimensions of the extrusion from one end cap to the other for the length of lens cover needed. Cut the lens by using a pair of straight-cut tin snips ensuring a clean cut. Once cut to size, snap one end of the lens and continue to press in the lens as you work towards the opposite end. STEP 5 - Soldering Power feeds Start by cutting two pieces of power feed wire to about (3/4 ) long and strip both positive and negative wire ends. Solder the positive wire to the (+24V DC) tab on one side of the tape, and the negative wire to the (-) tab marked on the opposite end of the tape light. STEP 8 - Measure Sconce for Wall Mount Spacing Once the Olin Sconce has been assembled, you will need to measure the overall mounting length. Measure eyelet to eyelet on the conductive end caps as this will be the spacing for installing the conductive Wall mounts and where the fixture will be hung. Conductive Wall Mounts (Sconce Length) STEP 4 - Installing Tape Light Install the tape light by peeling the backing film and placing within the Olin extrusion. Start the run of tape light (5/8 ) from one end of the Olin extrusion. There should be a (5/8 ) gap on the opposite end of the extrusion once tape light is fully installed. This will allow proper spacing for the conductive end caps to be soldered to the tape light. STEP 6 - Soldering Conductive End Caps Using the supplied conductive end caps (PE-OLIN-PWR-END), firmly press both end caps into Olin extrusion and solder the feed wire to the conductive tabs on both end caps. STEP 9 - Install Drywall Anchors Mark the location for the conductive wall mounts with the measurement from Step 8. Begin by drilling a (23/64) hole and Install the supplied drywall anchor and anchor bolt. Compress the drywall anchor by tightening the anchor bolt clockwise. This can be done with a power drill or standard screwdriver. Do not over tighten the anchor as it may damage the drywall. Once fully compressed or tightened, remove anchor bolt and discard. Repeat this process for any additional ceiling mounts needed. Continue to next page... 17

ASSEMBLING & INSTALLING OLIN SCONCES CONTINUED STEP 10 - Connect Power Wires to Wall Mounts 24V power wire must be run to install location for both positive (+24V DC) and negative (-) conductive mounts. Drill a (5/32) pilot hole and feed power wire through the wall. Drill the pilot hole as close as possible to the drywall anchor to ensure a covered finish. Once the power wires have been fed through the pilot hole, crimp the wire to the conductive tab. We recommended that this connection be soldered as well to ensure connection. STEP 15 - Mount the Fixture Begin mounting the fixture by feeding the conductive rod into one end of the fixtures conductive end cap. Tighten set screw using a (2.5mm) allen key and repeat this process for opposite end cap and support clips if applicable. The sconce fixture may be rotated once installed. To do so, simply rotate the extrusion on both ends simultaneously in any direction for desired look or effect. STEP 11 - Install Conductive Wall Mounts Place the conductive tab over the stem bolt and position the bolt so that the crimped tab will recess into the power feed hole in the drywall. Repeat this process for the other wall mount. To install conductive wall mounts, tighten the stem bolt by hand until fully flush to the drywall. STEP 12 - Cut and Install Conductive Rod The conductive rod comes in a 1M length and will need to be cut down for installation. We recommend that the sconces be mounted no further than (8 ) from the wall to ensure proper mounting. The conductive rod may be cut to size with a miter saw or hacksaw. Once cut, install the conductive rod into the conductive wall mounts by tightening the setscrew with a (2.5mm) allen key. 18

INSTALLATION NOTES