Ericsson PRODUCT TABLE OF CONTENTS SPECIFICATION 1 (1) (3) MPM/BY/P Henrik Sundh 1/1301 00152-EN/LZT146315 BMR 642 Technical 8 Uen Specification MPM/BY/M PME 8000 [Krister series Lundberg] PoL Regulators 2006-02-22 2006-02-20 A Key Features 6A output current 11.8-13.2V input voltage range Output voltages from 0.8V up to 5.5V Industry standard POLA compatible 22.1 x 12.57 x 8.51 mm (0.87 x 0.5 x 0.335 in.) High efficiency, up to. 94% Auto Track sequencing pin More than 4.4 million hours MTBF General Characteristics Operating temperature: -40ºC to 85ºC Input under voltage protection Start up into a pre-biased output safe Output short-circuit protection On/Off inhibit control Wide output voltage adjust function Highly automated manufacturing ensures quality ISO 9001/14001 certified supplier Safety Approvals Design for Environment Meets requirements in hightemperature lead-free soldering processes. Contents General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4 Product Program Ordering 0.8-1.8 V/6 A PME 8118T... 0.8 V/6 A Electrical Specification... 5 1.0 V/6 A Electrical Specification... 8 1.2 V/6 A Electrical Specification... 11 1.5 V/6 A Electrical Specification... 14 1.8 V/6 A Electrical Specification... 17 1.2-5.5 V/6 A PME 8318L... 1.2 V/6 A Electrical Specification... 20 1.5 V/6 A Electrical Specification... 23 1.8 V/6 A Electrical Specification... 26 2.5 V/6 A Electrical Specification... 29 3.3 V/6 A Electrical Specification... 32 5.0 V/6 A Electrical Specification... 35 EMC Specification... 37 Operating Information... 37 Thermal Consideration... 40 Connections... 41 Mechanical Information... 42 Soldering Information... 44 Delivery Information... 46 Product Qualification Specification... 47
MPM/BY/P Henrik Sundh Ericsson Internal PRODUCT SPECIFICATION 2 (3) 1/1301 BMR 642 Technical 8 Uen Specification 2 MPM/BY/M PME 8000 [Krister series Lundberg] PoL Regulators 2006-02-20 A General Information Ordering Information See Contents for individual product ordering numbers. Option Through hole pin SMD pin SMD pin, leadfree reflow temperature capable Reliability Suffix P S R PME8118TP PME8118TS PME8118TSR The Mean Time Between Failure (MTBF) is calculated at full output power and an operating ambient temperature (T A ) of +40 C. Different methods could be used to calculate the predicted MTBF and failure rate which may give different results. Flex currently uses Telcordia SR332. Predicted MTBF for the series is: - 4.40 million hours according to Telcordia SR332, issue 1, Black box technique. Telcordia SR332 is a commonly used standard method intended for reliability calculations in IT&T equipment. The parts count procedure used in this method was originally modelled on the methods from MIL-HDBK-217F, Reliability Predictions of Electronic Equipment. It assumes that no reliability data is available on the actual units and devices for which the predictions are to be made, i.e. all predictions are based on generic reliability parameters. Quality Statement The products are designed and manufactured in an industrial environment where quality systems and methods like ISO 9000, 6σ (sigma), and SPC are intensively in use to boost the continuous improvements strategy. Infant mortality or early failures in the products are screened out and they are subjected to an ATE-based final test. Conservative design rules, design reviews and product qualifications, plus the high competence of an engaged work force, contribute to the high quality of our products. Warranty Warranty period and conditions are defined in Flex General Terms and Conditions of Sale. Limitation of Liability Flex does not make any other warranties, expressed or implied including any warranty of merchantability or fitness for a particular purpose (including, but not limited to, use in life support applications, where malfunctions of product can cause injury to a person s health or life). Flex 2017 The information and specifications in this technical specification is believed to be correct at the time of publication. However, no liability is accepted for inaccuracies, printing errors or for any consequences thereof. Flex reserves the right to change the contents of this technical specification at any time without prior notice. Compatibility with RoHS requirements The products are compatible with the relevant clauses and requirements of the RoHS directive 2011/65/EU and have a maximum concentration value of 0.1% by weight in homogeneous materials for lead, mercury, hexavalent chromium, PBB and PBDE and of 0.01% by weight in homogeneous materials for cadmium. Exemptions in the RoHS directive utilized in Flex products are found in the Statement of Compliance document. Flex fulfills and will continuously fulfill all its obligations under regulation (EC) No 1907/2006 concerning the registration, evaluation, authorization and restriction of chemicals (REACH) as they enter into force and is through product materials declarations preparing for the obligations to communicate information on substances in the products.
MPM/BY/P Henrik Sundh Ericsson Internal PRODUCT SPECIFICATION 3 (3) 1/1301 BMR 642 Technical 8 Uen Specification 3 MPM/BY/M PME 8000 [Krister series Lundberg] PoL Regulators 2006-02-20 A Safety Specification General information Flex DC/DC converters and DC/DC regulators are designed in accordance with safety standards IEC/EN/ UL60950, Safety of Information Technology Equipment. IEC/EN/UL60950 contains requirements to prevent injury or damage due to the following hazards: Electrical shock Energy hazards Fire Mechanical and heat hazards Radiation hazards Chemical hazards On-board DC-DC converters are defined as component power supplies. As components they cannot fully comply with the provisions of any Safety requirements without Conditions of Acceptability. It is the responsibility of the installer to ensure that the final product housing these components complies with the requirements of all applicable Safety standards and Directives for the final product. Component power supplies for general use should comply with the requirements in IEC60950, EN60950 and UL60950 Safety of information technology equipment. There are other more product related standards, e.g. IEEE802.3af Ethernet LAN/MAN Data terminal equipment power, and ETS300132-2 Power supply interface at the input to telecommunications equipment; part 2: DC, but all of these standards are based on IEC/EN/UL60950 with regards to safety. Flex DC/DC converters and DC/DC regulators are UL60950 recognized and certified in accordance with EN60950. The flammability rating for all construction parts of the products meets requirements for V-0 class material according to IEC 60695-11-10. The products should be installed in the end-use equipment, in accordance with the requirements of the ultimate application. Normally the output of the DC/DC converter is considered as SELV (Safety Extra Low Voltage) and the input source must be isolated by minimum Double or Reinforced Insulation from the primary circuit (AC mains) in accordance with IEC/EN/UL60950. Isolated DC/DC converters It is recommended that a slow blow fuse with a rating twice the maximum input current per selected product be used at the input of each DC/DC converter. If an input filter is used in the circuit the fuse should be placed in front of the input filter. In the rare event of a component problem in the input filter or in the DC/DC converter that imposes a short circuit on the input source, this fuse will provide the following functions: Isolate the faulty DC/DC converter from the input power source so as not to affect the operation of other parts of the system. Protect the distribution wiring from excessive current and power loss thus preventing hazardous overheating. The galvanic isolation is verified in an electric strength test. The test voltage (V iso ) between input and output is 1500 Vdc or 2250 Vdc for 60 seconds (refer to product specification). Leakage current is less than 1 μa at nominal input voltage. 24 V DC systems The input voltage to the DC/DC converter is SELV (Safety Extra Low Voltage) and the output remains SELV under normal and abnormal operating conditions. 48 and 60 V DC systems If the input voltage to Flex DC/DC converter is 75 Vdc or less, then the output remains SELV (Safety Extra Low Voltage) under normal and abnormal operating conditions. Single fault testing in the input power supply circuit should be performed with the DC/DC converter connected to demonstrate that the input voltage does not exceed 75 Vdc. If the input power source circuit is a DC power system, the source may be treated as a TNV2 circuit and testing has demonstrated compliance with SELV limits and isolation requirements equivalent to Basic Insulation in accordance with IEC/EN/UL60950. Non-isolated DC/DC regulators The input voltage to the DC/DC regulator is SELV (Safety Extra Low Voltage) and the output remains SELV under normal and abnormal operating conditions.
PRODUCT SPEC. 1 (34) 2/1301-BMR 642 Technical 8 Uen Specification 4 SEC/D PME 8000 Wei Zhang series A PoL Regulators 2006-2-7 A Absolute Maximum Ratings Characteristics min typ max Unit T ref Operating Temperature (see Thermal Consideration section) 40 85 C T S Storage temperature 40 125 C V I Input voltage 10.8 12.0 V inh Inhibit On/Off pin voltage Positive logic option V in -0.5 Open V (see Operating Information section) Negative logic option N/A N/A V V adj Adjust pin voltage (see Operating Information section) N/A N/A V Stress in excess of Absolute Maximum Ratings may cause permanent damage. Absolute Maximum Ratings, sometimes referred to as no destruction limits, are normally tested with one parameter at a time exceeding the limits of Output data or Electrical Characteristics. If exposed to stress above these limits, function and performance may degrade in an unspecified manner. Fundamental Circuit Diagram +IN 3 2 1 2 +OUT 1 3 1 2 GND Auto Track TRK PWM Controller Error Amplifier ADJ Ref INH RC Block GND GND GND
PRODUCT SPEC. 2 (34) 2/1301-BMR 642 Technical 8 Uen Specification 5 SEC/D PME 8000 Wei Zhang series A PoL Regulators 2006-2-7 A 0.8 V/6 A Electrical Specification PME 8118T T ref = -40 to +85ºC, V I = 10.8 to, R adj = open, unless otherwise specified under Conditions. Typical values given at: T ref = +25 C, V I =, max I O, unless otherwise specified under Conditions. Additional C in =100uF and C out =330uF. See Operating Information section for selection of capacitor types. Connect the sense pin, where available, to the output pin. Characteristics Conditions min typ max Unit V I Input voltage range 10.8 V Ioff Turn-off input voltage Decreasing input voltage 8.8 9.0 V V Ion Turn-on input voltage Increasing input voltage 9.5 10.4 V C I Internal input capacitance 20 µf P O Output power 0 4.8 W η Efficiency 50 % of max I O 81.0 max I O 79.7 % P d Power Dissipation max I O 1.2 1.7 W P li Input idling power I O = 0, V I = 260 mw P RC Input standby power V I = (turned off with INHIBIT) 120 mw I S Static Input current V I =, max I O 0.5 A f s Switching frequency 0-100% of max I O 200 250 300 khz V Oi V O V tr t tr t r t s Output voltage initial setting and accuracy T ref = +25 C, V I =, max I O 0.784 0.800 0.816 V Output voltage tolerance band 10-100% of max I O 0.776 0.824 V Idling voltage I O = 0 0.797 V Line regulation max I O ±5 mv Load regulation V I =, 0-100% of max I O ±5 mv Load transient voltage deviation Load transient recovery time Ramp-up time (from 10 90 % of V Oi ) Start-up time (from V I connection to 90% of V Oi ) Vin shutdown fall time. V I =, Load step 50-100-50 % of max I O, di/dt = 1 A/µs, ±70 mv see Note 1 40 µs max I O 0.6 ms 12.9 ms t f Max I o 2.6 ms (From V I off to 10% of V O ) I o = 1A 14.7 ms INHIBIT start-up time Max I o 12.5 ms t Inh INHIBIT shutdown fall time Max I o 20 µs (From INHIBIT off to 10% of V O ) I o = 0.1 A 0.8 ms I O Output current 0 6 A I lim Current limit threshold T ref < max T ref, 14 A V Oac Output ripple & noise See ripple & noise section, V O 1.0; 20 max I O, V Oi V O >1.0; 30 mvp-p Note 1: Output filter according to Ripple & Noise section
PRODUCT SPEC. 3 (34) 2/1301-BMR 642 Technical 8 Uen Specification 6 SEC/D PME 8000 Wei Zhang series A PoL Regulators 2006-2-7 A 0.8 V/6 A Typical Characteristics PME 8118T Efficiency Power Dissipation [%] 100 [W] 4 95 90 85 80 75 70 3 2 1 0 Efficiency vs. load current and input voltage at T ref = +25 C Dissipated power vs. load current and input voltage at T ref = +25 C Output Current Derating Output Characteristics [A] 12 10 8 6 4 2 2.0 m/s 1.0 m/s 0.5 m/s Nat. Conv. [V] 0.90 0.85 0.80 0.75 0 0 20 40 60 80 [ C] 0.70 Available load current vs. ambient air temperature and airflow at V I =, V OUT = 1.8 V. See Thermal Consideration section. Output voltage vs. load current at T ref = +25 C
PRODUCT SPEC. E 4 (34) Approved series PME 8000 series SEC/D Wei Zhang A PoL Regulators Checked 2/1301-BMR 642Technical 8 Uen Specification Specification Date 2006-2-7 V, Output up tov, A / 33 W Inputregulator, 10.8-13.2 10.8-13.2 66 A/33 POL Input 10.8-13.2 V,6Output Output A/33 W W Rev Reference 3/28701BMR 642 Rev.A November 2017 EN/LZT 146 R1B March 2013 315 R1A February 2006 A Flex Ericsson Ericsson AB Power Modules AB 0.8 V/6 A Typical Characteristics Start-up Start-up enabled by connecting VI at: VI =. PME 8118T Shut-down Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 20 ms/div. Output Ripple & Noise Output voltage ripple (20mV/div.) at: VI =. Time scale: 2 µs/div. 7 Shut-down enabled by disconnecting VI at: VI =. Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 2.0 ms/div. Output Load Transient Response See the filter in the Output ripple and noise section (EMC Specification). Output voltage response to load current step- Top trace: output voltage (100mV/div.). change (3-6-3 A) at: Bottom trace: load current (2 A/div.). Tref =+25 C, VI =. Time scale: 0.1 ms/div.
PRODUCT SPEC. 5 (34) 2/1301-BMR 642 Technical 8 Uen Specification 8 SEC/D PME 8000 Wei Zhang series A PoL Regulators 2006-2-7 A 1.0 V/6 A Electrical Specification PME 8118T T ref = -40 to +85ºC, V I = 10.8 to, R adj = 32.4 kω, unless otherwise specified under Conditions. Typical values given at: T ref = +25 C, V I =, max I O, unless otherwise specified under Conditions. Additional C in =100uF and C out =330uF. See Operating Information section for selection of capacitor types. Connect the sense pin, where available, to the output pin. Characteristics Conditions min typ max Unit V I Input voltage range 10.8 V Ioff Turn-off input voltage Decreasing input voltage 8.8 9.0 V V Ion Turn-on input voltage Increasing input voltage 9.5 10.4 V C I Internal input capacitance 20 µf P O Output power 0 6 W η Efficiency 50 % of max I O 83.4 max I O 82.7 % P d Power Dissipation max I O 1.2 1.7 W P li Input idling power I O = 0, V I = 300 mw P RC Input standby power V I = (turned off with INHIBIT) 120 mw I S Static Input current V I =, max I O 0.6 A f s Switching frequency 0-100% of max I O 200 250 300 khz V Oi V O V tr t tr t r t s Output voltage initial setting and accuracy T ref = +25 C, V I =, max I O 0.980 1.000 1.020 V Output voltage tolerance band 10-100% of max I O 0.970 1.030 V Idling voltage I O = 0 0.995 V Line regulation max I O ±5 mv Load regulation V I =, 0-100% of max I O ±5 mv Load transient voltage deviation Load transient recovery time Ramp-up time (from 10 90 % of V Oi ) Start-up time (from V I connection to 90% of V Oi ) Vin shutdown fall time. V I =, Load step 50-100-50 % of max I O, di/dt = 1 A/µs, ±75 mv see Note 1 50 µs max I O 0.8 ms 13.1 ms t f Max I o 2.2 ms (From V I off to 10% of V O ) I o = 1A 12.1 ms INHIBIT start-up time Max I o 12.7 ms t Inh INHIBIT shutdown fall time Max I o 20 µs (From INHIBIT off to 10% of V O ) I o = 0.1 A 1.3 ms I O Output current 0 6 A I lim Current limit threshold T ref < max T ref, 14 A V Oac Output ripple & noise See ripple & noise section, V O 1.0; 20 max I O, V Oi V O >1.0; 30 mvp-p Note 1: Output filter according to Ripple & Noise section
PRODUCT SPEC. 6 (34) 2/1301-BMR 642 Technical 8 Uen Specification 9 SEC/D PME 8000 Wei Zhang series A PoL Regulators 2006-2-7 A 1.0 V/6 A Typical Characteristics PME 8118T Efficiency Power Dissipation [%] 100 [W] 4 95 90 85 80 75 3 2 1 70 0 Efficiency vs. load current and input voltage at T ref = +25 C Dissipated power vs. load current and input voltage at T ref = +25 C Output Current Derating Output Characteristics [A] 12 10 8 6 4 2 2.0 m/s 1.0 m/s 0.5 m/s Nat. Conv. [V] 1.10 1.05 1.00 0.95 0 0 20 40 60 80 [ C] 0.90 Available load current vs. ambient air temperature and airflow at V I =, V OUT = 1.8 V. See Thermal Consideration section. Output voltage vs. load current at T ref = +25 C
PRODUCT SPEC. E 7 (34) Approved series PME 8000 series SEC/D Wei Zhang A PoL Regulators Checked 2/1301-BMR 642Technical 8 Uen Specification Specification Date 2006-2-7 10.8-13.2 V, Output up tov, A / 33 W Inputregulator, 10.8-13.2 66 A/33 POL Input 10.8-13.2 V,6Output Output A/33 W W Rev Reference 3/28701BMR 642 Rev.A November 2017 EN/LZT 146 R1B March 2013 315 R1A February 2006 A Flex Ericsson Ericsson AB Power Modules AB 1.0 V/6 A Typical Characteristics Start-up Start-up enabled by connecting VI at: VI =. PME 8118T Shut-down Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 20 ms/div. Output Ripple & Noise Output voltage ripple (20mV/div.) at: VI =. Time scale: 2 µs/div. 10 Shut-down enabled by disconnecting VI at: VI =. Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 5.0 ms/div. Output Load Transient Response See the filter in the Output ripple and noise section (EMC Specification). Output voltage response to load current step- Top trace: output voltage (100mV/div.). change (3-6-3 A) at: Bottom trace: load current (2 A/div.). Tref =+25 C, VI =. Time scale: 0.1 ms/div.
PRODUCT SPEC. 8 (34) 2/1301-BMR 642 Technical 8 Uen Specification 11 SEC/D PME 8000 Wei Zhang series A PoL Regulators 2006-2-7 A 1.2 V/6 A Electrical Specification PME 8118T T ref = -40 to +85ºC, V I = 10.8 to, R adj = 12.1 kω, unless otherwise specified under Conditions. Typical values given at: T ref = +25 C, V I =, max I O, unless otherwise specified under Conditions. Additional C in =560uF and C out =330uF. See Operating Information section for selection of capacitor types. Connect the sense pin, where available, to the output pin. Characteristics Conditions min typ max Unit V I Input voltage range 10.8 V Ioff Turn-off input voltage Decreasing input voltage 8.8 9.0 V V Ion Turn-on input voltage Increasing input voltage 9.5 10.4 V C I Internal input capacitance 20 µf P O Output power 0 7.2 W η Efficiency 50 % of max I O 85.0 max I O 84.7 % P d Power Dissipation max I O 1.3 1.8 W P li Input idling power I O = 0, V I = 350 mw P RC Input standby power V I = (turned off with INHIBIT) 120 mw I S Static Input current V I =, max I O 0.7 A f s Switching frequency 0-100% of max I O 200 250 300 khz V Oi V O V tr t tr t r t s Output voltage initial setting and accuracy T ref = +25 C, V I =, max I O 1.176 1.200 1.224 V Output voltage tolerance band 10-100% of max I O 1.164 1.236 V Idling voltage I O = 0 1.196 V Line regulation max I O ±5 mv Load regulation V I =, 0-100% of max I O ±5 mv Load transient voltage deviation Load transient recovery time Ramp-up time (from 10 90 % of V Oi ) Start-up time (from V I connection to 90% of V Oi ) Vin shutdown fall time. V I =, Load step 50-100-50 % of max I O, di/dt = 1 A/µs, ±75 mv see Note 1 40 µs max I O 1.1 ms 13.5 ms t f Max I o 1.9 ms (From V I off to 10% of V O ) I o = 1A 10.2 ms INHIBIT start-up time Max I o 13.0 ms t Inh INHIBIT shutdown fall time Max I o 30 µs (From INHIBIT off to 10% of V O ) I o = 0.1 A 1.5 ms I O Output current 0 6 A I lim Current limit threshold T ref < max T ref, 14 A V Oac Output ripple & noise See ripple & noise section, V O 1.0; 20 max I O, V Oi V O >1.0; 30 mvp-p Note 1: Output filter according to Ripple & Noise section
PRODUCT SPEC. 9 (34) 2/1301-BMR 642 Technical 8 Uen Specification 12 SEC/D PME 8000 Wei Zhang series A PoL Regulators 2006-2-7 A 1.2 V/6 A Typical Characteristics PME 8118T Efficiency Power Dissipation [%] 100 [W] 4 95 90 85 80 75 3 2 1 70 0 Efficiency vs. load current and input voltage at T ref = +25 C Dissipated power vs. load current and input voltage at T ref = +25 C Output Current Derating Output Characteristics [A] 12 10 8 6 4 2 2.0 m/s 1.0 m/s 0.5 m/s Nat. Conv. [V] 1.30 1.25 1.20 1.15 0 0 20 40 60 80 [ C] 1.10 Available load current vs. ambient air temperature and airflow at V I =, V OUT = 1.8 V. See Thermal Consideration section. Output voltage vs. load current at T ref = +25 C
PRODUCT SPEC. E 10 (34) Approved series PME 8000 series SEC/D Wei Zhang A PoL Regulators Checked 2/1301-BMR 642Technical 8 Uen Specification Specification Date 2006-2-7 10.8-13.2 V, Output up tov, A / 33 W Inputregulator, 10.8-13.2 66 A/33 POL Input 10.8-13.2 V,6Output Output A/33 W W Rev Reference 3/28701BMR 642 Rev.A November 2017 EN/LZT 146 R1B March 2013 315 R1A February 2006 A Flex Ericsson Ericsson AB Power Modules AB 1.2 V/6 A Typical Characteristics Start-up Start-up enabled by connecting VI at: VI =. PME 8118T Shut-down Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 20 ms/div. Output Ripple & Noise Output voltage ripple (20mV/div.) at: VI =. Time scale: 2 µs/div. 13 Shut-down enabled by disconnecting VI at: VI =. Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 10.0 ms/div. Output Load Transient Response See the filter in the Output ripple and noise section (EMC Specification). Output voltage response to load current step- Top trace: output voltage (100mV/div.). change (3-6-3 A) at: Bottom trace: load current (2 A/div.). Tref =+25 C, VI =. Time scale: 0.1 ms/div.
PRODUCT SPEC. 11 (34) 2/1301-BMR 642 Technical 8 Uen Specification 14 SEC/D PME 8000 Wei Zhang series A PoL Regulators 2006-2-7 A 1.5 V/6 A Electrical Specification PME 8118T T ref = -40 to +85ºC, V I = 10.8 to, R adj = 3.57 kω, unless otherwise specified under Conditions. Typical values given at: T ref = +25 C, V I =, max I O, unless otherwise specified under Conditions. Additional C in =100uF and C out =330uF. See Operating Information section for selection of capacitor types. Connect the sense pin, where available, to the output pin. Characteristics Conditions min typ max Unit V I Input voltage range 10.8 V Ioff Turn-off input voltage Decreasing input voltage 8.8 9.0 V V Ion Turn-on input voltage Increasing input voltage 9.5 10.4 V C I Internal input capacitance 20 µf P O Output power 0 9 W η Efficiency 50 % of max I O 86.3 max I O 87.0 % P d Power Dissipation max I O 1.3 1.8 W P li Input idling power I O = 0, V I = 430 mw P RC Input standby power V I = (turned off with INHIBIT) 120 mw I S Static Input current V I =, max I O 0.9 A f s Switching frequency 0-100% of max I O 200 250 300 khz V Oi V O V tr t tr t r t s Output voltage initial setting and accuracy T ref = +25 C, V I =, max I O 1.470 1.500 1.530 V Output voltage tolerance band 10-100% of max I O 1.455 1.545 V Idling voltage I O = 0 1.493 V Line regulation max I O ±5 mv Load regulation V I =, 0-100% of max I O ±5 mv Load transient voltage deviation Load transient recovery time Ramp-up time (from 10 90 % of V Oi ) Start-up time (from V I connection to 90% of V Oi ) Vin shutdown fall time. V I =, Load step 50-100-50 % of max I O, di/dt = 1 A/µs, ±75 mv see Note 1 40 µs max I O 1.4 ms 13.7 ms t f Max I o 1.6 ms (From V I off to 10% of V O ) I o = 1A 8.3 ms INHIBIT start-up time Max I o 13.4 ms t Inh INHIBIT shutdown fall time Max I o 40 µs (From INHIBIT off to 10% of V O ) I o = 0.1 A 1.9 ms I O Output current 0 6 A I lim Current limit threshold T ref < max T ref, 14 A V Oac Output ripple & noise See ripple & noise section, V O 1.0; 20 max I O, V Oi V O >1.0; 30 mvp-p Note 1: Output filter according to Ripple & Noise section
PRODUCT SPEC. 12 (34) 2/1301-BMR 642 Technical 8 Uen Specification 15 SEC/D PME 8000 Wei Zhang series A PoL Regulators 2006-2-7 A 1.5 V/6 A Typical Characteristics PME 8118T Efficiency Power Dissipation [%] 100 [W] 4 95 90 85 80 75 3 2 1 70 0 Efficiency vs. load current and input voltage at T ref = +25 C Dissipated power vs. load current and input voltage at T ref = +25 C Output Current Derating Output Characteristics [A] 12 10 8 6 4 2 2.0 m/s 1.0 m/s 0.5 m/s Nat. Conv. [V] 1.60 1.55 1.50 1.45 0 0 20 40 60 80 [ C] 1.40 Available load current vs. ambient air temperature and airflow at V I =, V OUT = 1.8 V. See Thermal Consideration section. Output voltage vs. load current at T ref = +25 C
PRODUCT SPEC. E 13 (34) Approved series PME 8000 series SEC/D Wei Zhang A PoL Regulators Checked 2/1301-BMR 642Technical 8 Uen Specification Specification Date 2006-2-7 10.8-13.2 V, Output up tov, A / 33 W Inputregulator, 10.8-13.2 66 A/33 POL Input 10.8-13.2 V,6Output Output A/33 W W Rev Reference 3/28701BMR 642 Rev.A November 2017 EN/LZT 146 R1B March 2013 315 R1A February 2006 A Flex Ericsson Ericsson AB Power Modules AB 1.5 V/6 A Typical Characteristics Start-up Start-up enabled by connecting VI at: VI =. PME 8118T Shut-down Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 20 ms/div. Output Ripple & Noise Output voltage ripple (20mV/div.) at: VI =. Time scale: 2 µs/div. 16 Shut-down enabled by disconnecting VI at: VI =. Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 10.0 ms/div. Output Load Transient Response See the filter in the Output ripple and noise section (EMC Specification). Output voltage response to load current step- Top trace: output voltage (100mV/div.). change (3-6-3 A) at: Bottom trace: load current (2 A/div.). Tref =+25 C, VI =. Time scale: 0.1 ms/div.
PRODUCT SPEC. 14 (34) 2/1301-BMR 642 Technical 8 Uen Specification 17 SEC/D PME 8000 Wei Zhang series A PoL Regulators 2006-2-7 A 1.8 V/6 A Electrical Specification PME 8118T T ref = -40 to +85ºC, V I = 10.8 to, R adj = 130 Ω, unless otherwise specified under Conditions. Typical values given at: T ref = +25 C, V I =, max I O, unless otherwise specified under Conditions. Additional C in =560uF and C out =330uF. See Operating Information section for selection of capacitor types. Connect the sense pin, where available, to the output pin. Characteristics Conditions min typ max Unit V I Input voltage range 10.8 V Ioff Turn-off input voltage Decreasing input voltage 8.8 9.0 V V Ion Turn-on input voltage Increasing input voltage 9.5 10.4 V C I Internal input capacitance 20 µf P O Output power 0 10.8 W η Efficiency 50 % of max I O 87.3 max I O 88.1 % P d Power Dissipation max I O 1.4 1.9 W P li Input idling power I O = 0, V I = 520 mw P RC Input standby power V I = (turned off with INHIBIT) 120 mw I S Static Input current V I =, max I O 1.0 A f s Switching frequency 0-100% of max I O 200 250 300 khz V Oi V O V tr t tr t r t s Output voltage initial setting and accuracy T ref = +25 C, V I =, max I O 1.764 1.800 1.836 V Output voltage tolerance band 10-100% of max I O 1.746 1.854 V Idling voltage I O = 0 1.794 V Line regulation max I O ±5 mv Load regulation V I =, 0-100% of max I O ±5 mv Load transient voltage deviation Load transient recovery time Ramp-up time (from 10 90 % of V Oi ) Start-up time (from V I connection to 90% of V Oi ) Vin shutdown fall time. V I =, Load step 50-100-50 % of max I O, di/dt = 1 A/µs, ±80 mv see Note 1 40 µs max I O 1.7 ms 14.3 ms t f Max I o 1.3 ms (From V I off to 10% of V O ) I o = 1A 7.0 ms INHIBIT start-up time Max I o 14.1 ms t Inh INHIBIT shutdown fall time Max I o 40 µs (From INHIBIT off to 10% of V O ) I o = 0.1 A 2.0 ms I O Output current 0 6 A I lim Current limit threshold T ref < max T ref, 14 A V Oac Output ripple & noise See ripple & noise section, V O 1.0; 20 max I O, V Oi V O >1.0; 30 mvp-p Note 1: Output filter according to Ripple & Noise section
PRODUCT SPEC. 15 (34) 2/1301-BMR 642 Technical 8 Uen Specification 18 SEC/D PME 8000 Wei Zhang series A PoL Regulators 2006-2-7 A 1.8 V/6 A Typical Characteristics PME 8118T Efficiency Power Dissipation [%] 100 [W] 4 95 90 85 80 75 3 2 1 70 0 Efficiency vs. load current and input voltage at T ref = +25 C Dissipated power vs. load current and input voltage at T ref = +25 C Output Current Derating Output Characteristics [A] 12 10 8 6 4 2 2.0 m/s 1.0 m/s 0.5 m/s Nat. Conv. [V] 1.90 1.85 1.80 1.75 0 0 20 40 60 80 [ C] 1.70 Available load current vs. ambient air temperature and airflow at V I =, V OUT = 1.8 V. See Thermal Consideration section. Output voltage vs. load current at T ref = +25 C
PRODUCT SPEC. E 16 (34) Approved series PME 8000 series SEC/D Wei Zhang A PoL Regulators Checked 2/1301-BMR 642Technical 8 Uen Specification Specification Date 2006-2-7 10.8-13.2 V, Output up tov, A / 33 W Inputregulator, 10.8-13.2 66 A/33 POL Input 10.8-13.2 V,6Output Output A/33 W W Rev Reference 3/28701BMR 642 Rev.A November 2017 EN/LZT 146 R1B March 2013 315 R1A February 2006 A Flex Ericsson Ericsson AB Power Modules AB 1.8 V/6 A Typical Characteristics Start-up Start-up enabled by connecting VI at: VI =. PME 8118T Shut-down Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 20 ms/div. Output Ripple & Noise Output voltage ripple (20mV/div.) at: VI =. Time scale: 2 µs/div. 19 Shut-down enabled by disconnecting VI at: VI =. Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 10.0 ms/div. Output Load Transient Response See the filter in the Output ripple and noise section (EMC Specification). Output voltage response to load current step- Top trace: output voltage (100mV/div.). change (3-6-3 A) at: Bottom trace: load current (2 A/div.). Tref =+25 C, VI =. Time scale: 0.1 ms/div.
PRODUCT SPEC. 17 (34) 2/1301-BMR 642 Technical 8 Uen Specification 20 SEC/D PME 8000 Wei Zhang series A PoL Regulators 2006-2-7 A 1.2 V/6 A Electrical Specification PME 8318L T ref = -40 to +85ºC, V I = 10.8 to, R adj = open, unless otherwise specified under Conditions. Typical values given at: T ref = +25 C, V I =, max I O, unless otherwise specified under Conditions. Additional C in =100uF and C out =330uF. See Operating Information section for selection of capacitor types. Connect the sense pin, where available, to the output pin. Characteristics Conditions min typ max Unit V I Input voltage range 10.8 V Ioff Turn-off input voltage Decreasing input voltage 8.8 9.0 V V Ion Turn-on input voltage Increasing input voltage 9.5 10.4 V C I Internal input capacitance 20 µf P O Output power 0 7.2 W η Efficiency 50 % of max I O 83.9 max I O 83.8 % P d Power Dissipation max I O 1.4 1.9 W P li Input idling power I O = 0, V I = 360 mw P RC Input standby power V I = (turned off with INHIBIT) 120 mw I S Static Input current V I =, max I O 0.7 A f s Switching frequency 0-100% of max I O 260 320 380 khz V Oi V O V tr t tr t r t s Output voltage initial setting and accuracy T ref = +25 C, V I =, max I O 1.176 1.200 1.224 V Output voltage tolerance band 10-100% of max I O 1.164 1.236 V Idling voltage I O = 0 1.199 V Line regulation max I O ±5 mv Load regulation V I =, 0-100% of max I O ±5 mv Load transient voltage deviation Load transient recovery time Ramp-up time (from 10 90 % of V Oi ) Start-up time (from V I connection to 90% of V Oi ) Vin shutdown fall time. V I =, Load step 50-100-50 % of max I O, di/dt = 1 A/µs, ±80 mv see Note 1 30 µs max I O 1.3 ms 13.3 ms t f Max I o 1.9 ms (From V I off to 10% of V O ) I o = 1A 10.1 ms INHIBIT start-up time Max I o 12.7 ms t Inh INHIBIT shutdown fall time Max I o 30 µs (From INHIBIT off to 10% of V O ) I o = 0.1 A 1.5 ms I O Output current 0 6 A I lim Current limit threshold T ref < max T ref, 14 A V Oac Output ripple & noise See ripple & noise section, V O 2.5; 25 mvp-p max I O, V Oi V O >2.5; 1 % V O Note 1: Output filter according to Ripple & Noise section
PRODUCT SPEC. 18 (34) 2/1301-BMR 642 Technical 8 Uen Specification 21 SEC/D PME 8000 Wei Zhang series A PoL Regulators 2006-2-7 A 1.2 V/6 A Typical Characteristics PME 8318L Efficiency Power Dissipation [%] 100 [W] 4 95 90 85 80 75 3 2 1 70 0 Efficiency vs. load current and input voltage at T ref = +25 C Dissipated power vs. load current and input voltage at T ref = +25 C Output Current Derating [A] 8 Output Characteristics [V] 1.30 6 2.0 m/s 1.25 4 2 1.0 m/s 0.5 m/s 1.20 1.15 0 0 20 40 60 80 [ C] Nat. Conv. 1.10 Available load current vs. ambient air temperature and airflow at V I =, V OUT = 3.3 V. See Thermal Consideration section. Output voltage vs. load current at T ref = +25 C
PRODUCT SPEC. E 19 (34) Approved series PME 8000 series SEC/D Wei Zhang A PoL Regulators Checked 2/1301-BMR 642Technical 8 Uen Specification Specification Date 2006-2-7 10.8-13.2 V, Output up tov, A / 33 W Inputregulator, 10.8-13.2 66 A/33 POL Input 10.8-13.2 V,6Output Output A/33 W W Rev Reference 3/28701BMR 642 Rev.A November 2017 EN/LZT 146 R1B March 2013 315 R1A February 2006 A Flex Ericsson Ericsson AB Power Modules AB 1.2 V/6 A Typical Characteristics Start-up Start-up enabled by connecting VI at: VI =. PME 8318L Shut-down Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 20 ms/div. Output Ripple & Noise Output voltage ripple (20mV/div.) at: VI =. Time scale: 2 µs/div. 22 Shut-down enabled by disconnecting VI at: VI =. Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 5.0 ms/div. Output Load Transient Response See the filter in the Output ripple and noise section (EMC Specification). Output voltage response to load current step- Top trace: output voltage (100mV/div.). change (3-6-3 A) at: Bottom trace: load current (10 A/div.). Tref =+25 C, VI =. Time scale: 0.1 ms/div.
PRODUCT SPEC. 20 (34) 2/1301-BMR 642 Technical 8 Uen Specification 23 SEC/D PME 8000 Wei Zhang series A PoL Regulators 2006-2-7 A 1.5 V/6 A Electrical Specification PME 8318L T ref = -40 to +85ºC, V I = 10.8 to, R adj = 24.3 kω, unless otherwise specified under Conditions. Typical values given at: T ref = +25 C, V I =, max I O, unless otherwise specified under Conditions. Additional C in =100uF and C out =330uF. See Operating Information section for selection of capacitor types. Connect the sense pin, where available, to the output pin. Characteristics Conditions min typ max Unit V I Input voltage range 10.8 V Ioff Turn-off input voltage Decreasing input voltage 8.8 9.0 V V Ion Turn-on input voltage Increasing input voltage 9.5 10.4 V C I Internal input capacitance 20 µf P O Output power 0 9 W η Efficiency 50 % of max I O 85.7 max I O 86.1 % P d Power Dissipation max I O 1.5 2.0 W P li Input idling power I O = 0, V I = 430 mw P RC Input standby power V I = (turned off with INHIBIT) 120 mw I S Static Input current V I =, max I O 0.9 A f s Switching frequency 0-100% of max I O 260 320 380 khz V Oi V O V tr t tr t r t s Output voltage initial setting and accuracy T ref = +25 C, V I =, max I O 1.470 1.500 1.530 V Output voltage tolerance band 10-100% of max I O 1.455 1.545 V Idling voltage I O = 0 1.506 V Line regulation max I O ±5 mv Load regulation V I =, 0-100% of max I O ±5 mv Load transient voltage deviation Load transient recovery time Ramp-up time (from 10 90 % of V Oi ) Start-up time (from V I connection to 90% of V Oi ) Vin shutdown fall time. V I =, Load step 50-100-50 % of max I O, di/dt = 1 A/µs, ±80 mv see Note 1 30 µs max I O 1.5 ms 13.6 ms t f Max I o 1.5 ms (From V I off to 10% of V O ) I o = 1A 8.4 ms INHIBIT start-up time Max I o 13.0 ms t Inh INHIBIT shutdown fall time Max I o 40 µs (From INHIBIT off to 10% of V O ) I o = 0.1 A 1.9 ms I O Output current 0 6 A I lim Current limit threshold T ref < max T ref, 14 A V Oac Output ripple & noise See ripple & noise section, V O 2.5; 25 mvp-p max I O, V Oi V O >2.5; 1 % V O Note 1: Output filter according to Ripple & Noise section
PRODUCT SPEC. 21 (34) 2/1301-BMR 642 Technical 8 Uen Specification 24 SEC/D PME 8000 Wei Zhang series A PoL Regulators 2006-2-7 A 1.5 V/6 A Typical Characteristics PME 8318L Efficiency Power Dissipation [%] 100 [W] 4 95 90 85 80 75 3 2 1 70 0 Efficiency vs. load current and input voltage at T ref = +25 C Dissipated power vs. load current and input voltage at T ref = +25 C Output Current Derating Output Characteristics [A] 8 [V] 1.60 6 4 2 2.0 m/s 1.0 m/s 0.5 m/s 1.55 1.50 1.45 0 0 20 40 60 80 [ C] Nat. Conv. 1.40 Available load current vs. ambient air temperature and airflow at V I =, V OUT = 3.3 V. See Thermal Consideration section. Output voltage vs. load current at T ref = +25 C
PRODUCT SPEC. E 22 (34) Approved series PME 8000 series SEC/D Wei Zhang A PoL Regulators Checked 2/1301-BMR 642Technical 8 Uen Specification Specification Date 2006-2-7 10.8-13.2 V, Output up tov, A / 33 W Inputregulator, 10.8-13.2 66 A/33 POL Input 10.8-13.2 V,6Output Output A/33 W W Rev Reference 3/28701BMR 642 Rev.A November 2017 EN/LZT 146 R1B March 2013 315 R1A February 2006 A Flex Ericsson Ericsson AB Power Modules AB 1.5 V/6 A Typical Characteristics Start-up Start-up enabled by connecting VI at: VI =. PME 8318L Shut-down Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 20 ms/div. Output Ripple & Noise Output voltage ripple (20mV/div.) at: VI =. Time scale: 2 µs/div. 25 Shut-down enabled by disconnecting VI at: VI =. Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 5.0 ms/div. Output Load Transient Response See the filter in the Output ripple and noise section (EMC Specification). Output voltage response to load current step- Top trace: output voltage (100mV/div.). change (3-6-3 A) at: Bottom trace: load current (10 A/div.). Tref =+25 C, VI =. Time scale: 0.1 ms/div.
PRODUCT SPEC. 23 (34) 2/1301-BMR 642 Technical 8 Uen Specification 26 SEC/D PME 8000 Wei Zhang series A PoL Regulators 2006-2-7 A 1.8 V/6 A Electrical Specification PME 8318L T ref = -40 to +85ºC, V I = 10.8 to, R adj = 11.5 kω, unless otherwise specified under Conditions. Typical values given at: T ref = +25 C, V I =, max I O, unless otherwise specified under Conditions. Additional C in =100uF and C out =330uF. See Operating Information section for selection of capacitor types. Connect the sense pin, where available, to the output pin. Characteristics Conditions min typ max Unit V I Input voltage range 10.8 V Ioff Turn-off input voltage Decreasing input voltage 8.8 9.0 V V Ion Turn-on input voltage Increasing input voltage 9.5 10.4 V C I Internal input capacitance 20 µf P O Output power 0 10.8 W η Efficiency 50 % of max I O 86.7 max I O 87.5 % P d Power Dissipation max I O 1.5 2.0 W P li Input idling power I O = 0, V I = 500 mw P RC Input standby power V I = (turned off with INHIBIT) 120 mw I S Static Input current V I =, max I O 1.0 A f s Switching frequency 0-100% of max I O 260 320 380 khz V Oi V O V tr t tr t r t s Output voltage initial setting and accuracy T ref = +25 C, V I =, max I O 1.764 1.800 1.836 V Output voltage tolerance band 10-100% of max I O 1.746 1.854 V Idling voltage I O = 0 1.798 V Line regulation max I O ±5 mv Load regulation V I =, 0-100% of max I O ±5 mv Load transient voltage deviation Load transient recovery time Ramp-up time (from 10 90 % of V Oi ) Start-up time (from V I connection to 90% of V Oi ) Vin shutdown fall time. V I =, Load step 50-100-50 % of max I O, di/dt = 1 A/µs, ±80 mv see Note 1 20 µs max I O 1.7 ms 14.0 ms t f Max I o 1.3 ms (From V I off to 10% of V O ) I o = 1A 7.2 ms INHIBIT start-up time Max I o 13.3 ms t Inh INHIBIT shutdown fall time Max I o 40 µs (From INHIBIT off to 10% of V O ) I o = 0.1 A 2.3 ms I O Output current 0 6 A I lim Current limit threshold T ref < max T ref, 14 A V Oac Output ripple & noise See ripple & noise section, V O 2.5; 25 mvp-p max I O, V Oi V O >2.5; 1 % V O Note 1: Output filter according to Ripple & Noise section
PRODUCT SPEC. 24 (34) 2/1301-BMR 642 Technical 8 Uen Specification 27 SEC/D PME 8000 Wei Zhang series A PoL Regulators 2006-2-7 A 1.8 V/6 A Typical Characteristics PME 8318L Efficiency Power Dissipation [%] 100 [W] 4 95 90 85 80 75 3 2 1 70 0 Efficiency vs. load current and input voltage at T ref = +25 C Dissipated power vs. load current and input voltage at T ref = +25 C Output Current Derating [A] 8 Output Characteristics [V] 1.90 6 4 2 2.0 m/s 1.0 m/s 0.5 m/s 1.85 1.80 1.75 0 0 20 40 60 80 [ C] Nat. Conv. 1.70 Available load current vs. ambient air temperature and airflow at V I =, V OUT = 3.3 V. See Thermal Consideration section. Output voltage vs. load current at T ref = +25 C
PRODUCT SPEC. E 25 (34) Approved series PME 8000 series SEC/D Wei Zhang A PoL Regulators Checked 2/1301-BMR 642Technical 8 Uen Specification Specification Date 2006-2-7 10.8-13.2 V, Output up tov, A / 33 W Inputregulator, 10.8-13.2 66 A/33 POL Input 10.8-13.2 V,6Output Output A/33 W W Rev Reference 3/28701BMR 642 Rev.A November 2017 EN/LZT 146 R1B March 2013 315 R1A February 2006 A Flex Ericsson Ericsson AB Power Modules AB 1.8 V/6 A Typical Characteristics Start-up Start-up enabled by connecting VI at: VI =. PME 8318L Shut-down Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 10 ms/div. Output Ripple & Noise Output voltage ripple (20mV/div.) at: VI =. Time scale: 2 µs/div. 28 Shut-down enabled by disconnecting VI at: VI =. Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 5.0 ms/div. Output Load Transient Response See the filter in the Output ripple and noise section (EMC Specification). Output voltage response to load current step- Top trace: output voltage (100mV/div.). change (3-6-3 A) at: Bottom trace: load current (10 A/div.). Tref =+25 C, VI =. Time scale: 0.1 ms/div.
PRODUCT SPEC. 26 (34) 2/1301-BMR 642 Technical 8 Uen Specification 29 SEC/D PME 8000 Wei Zhang series A PoL Regulators 2006-2-7 A 2.5 V/6 A Electrical Specification PME 8318L T ref = -40 to +85ºC, V I = 10.8 to, R adj = 4.32 kω, unless otherwise specified under Conditions. Typical values given at: T ref = +25 C, V I =, max I O, unless otherwise specified under Conditions. Additional C in =100uF and C out =330uF. See Operating Information section for selection of capacitor types. Connect the sense pin, where available, to the output pin. Characteristics Conditions min typ max Unit V I Input voltage range 10.8 V Ioff Turn-off input voltage Decreasing input voltage 8.8 9.0 V V Ion Turn-on input voltage Increasing input voltage 9.5 10.4 V C I Internal input capacitance 20 µf P O Output power 0 15 W η Efficiency 50 % of max I O 88.8 max I O 89.9 % P d Power Dissipation max I O 1.7 2.2 W P li Input idling power I O = 0, V I = 630 mw P RC Input standby power V I = (turned off with INHIBIT) 120 mw I S Static Input current V I =, max I O 1.5 A f s Switching frequency 0-100% of max I O 260 320 380 khz V Oi V O V tr t tr t r t s Output voltage initial setting and accuracy T ref = +25 C, V I =, max I O 2.450 2.500 2.550 V Output voltage tolerance band 10-100% of max I O 2.425 2.575 V Idling voltage I O = 0 2.506 V Line regulation max I O ±5 mv Load regulation V I =, 0-100% of max I O ±5 mv Load transient voltage deviation Load transient recovery time Ramp-up time (from 10 90 % of V Oi ) Start-up time (from V I connection to 90% of V Oi ) Vin shutdown fall time. V I =, Load step 50-100-50 % of max I O, di/dt = 1 A/µs, ±80 mv see Note 1 20 µs max I O 2.5 ms 15.0 ms t f Max I o 1.0 ms (From V I off to 10% of V O ) I o = 1A 5.4 ms INHIBIT start-up time Max I o 14.3 ms t Inh INHIBIT shutdown fall time Max I o 60 µs (From INHIBIT off to 10% of V O ) I o = 0.1 A 3.0 ms I O Output current 0 6 A I lim Current limit threshold T ref < max T ref, 14 A V Oac Output ripple & noise See ripple & noise section, V O 2.5; 25 mvp-p max I O, V Oi V O >2.5; 1 % V O Note 1: Output filter according to Ripple & Noise section
PRODUCT SPEC. 27 (34) 2/1301-BMR 642 Technical 8 Uen Specification 30 SEC/D PME 8000 Wei Zhang series A PoL Regulators 2006-2-7 A 2.5 V/6 A Typical Characteristics PME 8318L Efficiency Power Dissipation [%] 100 [W] 4 95 90 85 80 75 3 2 1 70 0 Efficiency vs. load current and input voltage at T ref = +25 C Dissipated power vs. load current and input voltage at T ref = +25 C Output Current Derating [A] 8 Output Characteristics [V] 2.60 6 4 2 2.0 m/s 1.0 m/s 0.5 m/s 2.55 2.50 2.45 0 0 20 40 60 80 [ C] Nat. Conv. 2.40 Available load current vs. ambient air temperature and airflow at V I =, V OUT = 3.3 V. See Thermal Consideration section. Output voltage vs. load current at T ref = +25 C
PRODUCT SPEC. E 28 (34) Approved series PME 8000 series SEC/D Wei Zhang A PoL Regulators Checked 2/1301-BMR 642Technical 8 Uen Specification Specification Date 2006-2-7 10.8-13.2 V, Output up tov, A / 33 W Inputregulator, 10.8-13.2 66 A/33 POL Input 10.8-13.2 V,6Output Output A/33 W W Rev Reference 3/28701BMR 642 Rev.A November 2017 EN/LZT 146 R1B March 2013 315 R1A February 2006 A Flex Ericsson Ericsson AB Power Modules AB 2.5 V/6 A Typical Characteristics Start-up Start-up enabled by connecting VI at: VI =. PME 8318L Shut-down Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 10 ms/div. Output Ripple & Noise Output voltage ripple (20mV/div.) at: VI =. Time scale: 2 µs/div. 31 Shut-down enabled by disconnecting VI at: VI =. Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 2.0 ms/div. Output Load Transient Response See the filter in the Output ripple and noise section (EMC Specification). Output voltage response to load current step- Top trace: output voltage (100mV/div.). change (3-6-3 A) at: Bottom trace: load current (10 A/div.). Tref =+25 C, VI =. Time scale: 0.1 ms/div.
PRODUCT SPEC. 29 (34) 2/1301-BMR 642 Technical 8 Uen Specification 32 SEC/D PME 8000 Wei Zhang series A PoL Regulators 2006-2-7 A 3.3 V/6 A Electrical Specification PME 8318L T ref = -40 to +85ºC, V I = 10.8 to, R adj = 2.00 kω, unless otherwise specified under Conditions. Typical values given at: T ref = +25 C, V I =, max I O, unless otherwise specified under Conditions. Additional C in =100uF and C out =330uF. See Operating Information section for selection of capacitor types. Connect the sense pin, where available, to the output pin. Characteristics Conditions min typ max Unit V I Input voltage range 10.8 V Ioff Turn-off input voltage Decreasing input voltage 8.8 9.0 V V Ion Turn-on input voltage Increasing input voltage 9.5 10.4 V C I Internal input capacitance 20 µf P O Output power 0 19.8 W η Efficiency 50 % of max I O 89.2 max I O 90.7 % P d Power Dissipation max I O 2.0 2.5 W P li Input idling power I O = 0, V I = 860 mw P RC Input standby power V I = (turned off with INHIBIT) 120 mw I S Static Input current V I =, max I O 1.8 A f s Switching frequency 0-100% of max I O 260 320 380 khz V Oi V O V tr t tr t r t s Output voltage initial setting and accuracy T ref = +25 C, V I =, max I O 3.234 3.300 3.366 V Output voltage tolerance band 10-100% of max I O 3.201 3.399 V Idling voltage I O = 0 3.298 V Line regulation max I O ±5 mv Load regulation V I =, 0-100% of max I O ±5 mv Load transient voltage deviation Load transient recovery time Ramp-up time (from 10 90 % of V Oi ) Start-up time (from V I connection to 90% of V Oi ) Vin shutdown fall time. V I =, Load step 50-100-50 % of max I O, di/dt = 1 A/µs, ±80 mv see Note 1 10 µs max I O 3.5 ms 16.0 ms t f Max I o 0.8 ms (From V I off to 10% of V O ) I o = 1A 4.3 ms INHIBIT start-up time Max I o 15.5 ms t Inh INHIBIT shutdown fall time Max I o 80 µs (From INHIBIT off to 10% of V O ) I o = 0.1 A 4.0 ms I O Output current 0 6 A I lim Current limit threshold T ref < max T ref, 14 A V Oac Output ripple & noise See ripple & noise section, V O 2.5; 25 mvp-p max I O, V Oi V O >2.5; 1 % V O Note 1: Output filter according to Ripple & Noise section
PRODUCT SPEC. 30 (34) 2/1301-BMR 642 Technical 8 Uen Specification 33 SEC/D PME 8000 Wei Zhang series A PoL Regulators 2006-2-7 A 3.3 V/6 A Typical Characteristics PME 8318L Efficiency Power Dissipation [%] 100 [W] 4 95 90 85 80 75 3 2 1 70 0 Efficiency vs. load current and input voltage at T ref = +25 C Dissipated power vs. load current and input voltage at T ref = +25 C Output Current Derating [A] 8 Output Characteristics [V] 3.40 6 4 2 2.0 m/s 1.0 m/s 0.5 m/s 3.35 3.30 3.25 0 0 20 40 60 80 [ C] Nat. Conv. 3.20 Available load current vs. ambient air temperature and airflow at V I =, V OUT = 3.3 V. See Thermal Consideration section. Output voltage vs. load current at T ref = +25 C
PRODUCT SPEC. E 31 (34) Approved series PME 8000 series SEC/D Wei Zhang A PoL Regulators Checked 2/1301-BMR 642Technical 8 Uen Specification Specification Date 2006-2-7 10.8-13.2 V, Output up tov, A / 33 W Inputregulator, 10.8-13.2 66 A/33 POL Input 10.8-13.2 V,6Output Output A/33 W W Rev Reference 3/28701BMR 642 Rev.A November 2017 EN/LZT 146 R1B March 2013 315 R1A February 2006 A Flex Ericsson Ericsson AB Power Modules AB 3.3 V/6 A Typical Characteristics Start-up Start-up enabled by connecting VI at: VI =. PME 8318L Shut-down Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 10 ms/div. Output Ripple & Noise Output voltage ripple (20mV/div.) at: VI =. Time scale: 2 µs/div. 34 Shut-down enabled by disconnecting VI at: VI =. Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 2.0 ms/div. Output Load Transient Response See the filter in the Output ripple and noise section (EMC Specification). Output voltage response to load current step- Top trace: output voltage (100mV/div.). change (3-6-3 A) at: Bottom trace: load current (10 A/div.). Tref =+25 C, VI =. Time scale: 0.1 ms/div.
PRODUCT SPEC. 32 (34) 2/1301-BMR 642 Technical 8 Uen Specification 35 SEC/D PME 8000 Wei Zhang series A PoL Regulators 2006-2-7 A 5.0 V/6 A Electrical Specification PME 8318L T ref = -40 to +85ºC, V I = 10.8 to, R adj = 280 Ω, unless otherwise specified under Conditions. Typical values given at: T ref = +25 C, V I =, max I O, unless otherwise specified under Conditions. Additional C in =100uF and C out =330uF. See Operating Information section for selection of capacitor types. Connect the sense pin, where available, to the output pin. Characteristics Conditions min typ max Unit V I Input voltage range 10.8 V Ioff Turn-off input voltage Decreasing input voltage 8.8 9.0 V V Ion Turn-on input voltage Increasing input voltage 9.5 10.4 V C I Internal input capacitance 20 µf P O Output power 0 30 W η Efficiency 50 % of max I O 91.2 max I O 93.1 % P d Power Dissipation max I O 2.2 2.7 W P li Input idling power I O = 0, V I = 1200 mw P RC Input standby power V I = (turned off with INHIBIT) 120 mw I S Static Input current V I =, max I O 2.7 A f s Switching frequency 0-100% of max I O 260 320 380 khz V Oi V O V tr t tr t r t s Output voltage initial setting and accuracy T ref = +25 C, V I =, max I O 4.900 5.000 5.100 V Output voltage tolerance band 10-100% of max I O 4.850 5.150 V Idling voltage I O = 0 5.007 V Line regulation max I O ±5 mv Load regulation V I =, 0-100% of max I O ±5 mv Load transient voltage deviation Load transient recovery time Ramp-up time (from 10 90 % of V Oi ) Start-up time (from V I connection to 90% of V Oi ) Vin shutdown fall time. V I =, Load step 50-100-50 % of max I O, di/dt = 1 A/µs, ±90 mv see Note 1 10 µs max I O 6.0 ms 18.3 ms t f Max I o 0.6 ms (From V I off to 10% of V O ) I o = 1A 3.4 ms INHIBIT start-up time Max I o 18.2 ms t Inh INHIBIT shutdown fall time Max I o 120 µs (From INHIBIT off to 10% of V O ) I o = 0.1 A 6.2 ms I O Output current 0 6 A I lim Current limit threshold T ref < max T ref, 14 A V Oac Output ripple & noise See ripple & noise section, V O 2.5; 25 mvp-p max I O, V Oi V O >2.5; 1 % V O Note 1: Output filter according to Ripple & Noise section