Breathable Wall Light Traps & Blackout Fan & Shutter Kits

Breathable Wall Light Traps & Blackout Fan & Shutter Kits 2017 Growers Supply All Rights Reserved. Reproduction is prohibited without permission. Maintain controlled airflow without sacrificing blackout environments. *Actual components may differ from what is shown. Revision date: 03.15.17 1

Important Information READ THIS DOCUMENT BEFORE YOU BEGIN Thank you for purchasing the breathable wall light trap and kit. When properly assembled and maintained, this product will provide years of reliable service. These instructions include helpful hints and important information needed to safely assemble and properly maintain the kit components. Please read these instructions before you begin. If you have any questions during the assembly, contact Customer Service at 1.800.245.9881 for assistance. SAFETY PRECAUTIONS Wear eye protection. Wear gloves when handling metal parts. Use a portable GFCI (Ground Fault Circuit Interrupter) when working with electric power tools and cords. REQUIRED TOOLS The following list identifies the main tools needed to assemble and install the breathable wall light trap and kit components (if applicable). Additional tools may be needed. Tape measure and marker. Variable speed drill (cordless with extra batteries works best) & 3/8" drill bit. Small hammer and gloves. Level (length depends on kit dimensions). 7/16" & 1/2" wrenches and a socket set containing 7/16" & 1/2" deep-well socket. Wrench set, tool to cut 1/8" cable, & pliers. ASSEMBLY PROCEDURE Following the instructions as presented will help ensure proper assembly. Steps outlining assembly process are as follows: 1. Verify that all parts are included in the shipment. Notify customer service for questions or concerns. 2. Read these instructions and all additional documentation included with the shipment before you begin. 3. Gather the tools and assistants. Assistants are needed to lift and hold assembly when attaching to building frame. 4. Assemble kit components. Read this document to determine what pages apply to your kit. 5. Read the care and maintenance information. CARE AND MAINTENANCE Proper care and maintenance is important. Check the following items periodically to ensure breathable wall light trap components are secure and functioning properly. Check all fasteners to verify they remain tight. Never climb or stand on any part of the light trap and its frame components. Ensure nothing blocks either side of light trap. Inspect all electrical connections and wires. Repair or replace as needed. Repair or replace loose or broken wires. For replacement or missing parts, call 1.800.245.9881 for assistance. WARNING: IF KIT INCLUDES MOTORIZED SHUTTER OR AN ELECTRIC FAN, CONSULT THE SERVICES OF A QUALIFIED ELECTRICIAN TO ADEQUATELY AND SAFELY CONNECT COMPONENTS TO A POWER SUPPLY. ALL ELECTRICAL CIRCUITS SHALL BE DESIGNED IN ACCORDANCE WITH LOCAL AND REGIONAL BUILDING CODES AND STANDARDS. 2 Light Traps and Kits Revision date: 03.15.17

Getting Started: Basic Kit Descriptions and Components Different kits include different components. Use the information on this page to identify which procedures apply to your breathable wall light trap kit. Kit numbers that end with the letter A (e.g., 113393A) include an assembled light trap. Skip Sections 1 & 2 if your kit includes an assembled light trap. For these blackout fan kits, complete Procedures 1 & 2 and Procedure 3 or 4: 113393 & 113393A 113394 & 113394A 113419 & 113419A 113435 & 113435A 113436 & 113436A For these blackout shutter kits, complete Procedure 1 & 2 and Procedure 5: 113395 & 113395A 113420 & 113420A 115424 & 115424A 115425 & 115425A For these blackout shutter kits, complete Procedure 1 & 2 and Procedure 6: 113421 & 113421A 113437 & 113437A 113448 & 113448A 115426 & 115426A 115427 & 115427A 115428 & 115428A Assembled Frame Column Shutter Shutter Light Trap Shutter Procedure 3 Fan Light Trap Shutter Motor & Mounting Bracket Frame Column Light Trap Light Trap Frame Column Combination Fan & Shutter Assembled Light Trap Frame Column Pully Shutter Motor Procedure 4 Light Traps and Kits Revision date: 03.15.17 3

Getting Started: Parts and Light Trap to Detail PICTORIAL PARTS GUIDE Diagram in this column shows basic light trap to adapter box connection. Sample shown may differ from actual components. Install a flat washer against bolt head and locknut at each connection. Diagram shows four connection points. Actual assembly may have more fasteners. FAG304B 1/4" Hex Bolt FALF35B 1/4" Locknuts FAME50B 1/4" Flat Washer FAMF03B 5/16" Fender Washer FA4482B Tek Screw FAG304B bolt (4) FALF35B locknut (4) FAME50B flat washers (8) FA3182 5/16" x 3" Elevator Bolt (fan kits only) *Some parts are not shown. 115161 5/16" Jam Nut (fan kits only) FALB02B 5/16" Nut (fan kits only) FAME07B 5/16" Flat Washer (fan kits only) FAMA37B 5/16" Lock Washer (fan kits only) Adapter Box Light Trap GENERAL ASSEMBLY STEPS 100441 Nut Setter 111983 Weather Stripping 1. Assemble vane kit components. (All kits: Procedure 1. Does not apply if kit number ends with letter A.) 2. Assemble vane kit frame. (All kits: Procedure 2. Does not apply if kit number ends with letter A.) 3. Install shutter or fan in building wall. (Blackout fan/shutter kits only Procedures 3-6, depending on kit components.) 4. Attach light trap adapter box* to building frame. (*Included with kits where breathable wall light trap is larger than fan or shutter Procedures 3-5.) 5. Attach assembled vane kit and frame to light trap adapter box*. (*Included with kits where breathable wall light trap is larger than fan or shutter Procedures 3-5.) NOTE: Install light trap inside building. OR: Attach assembled vane kit with frame to building frame Procedure 6 (no adapter box). NOTE: Vane kits with shutters of the same size do not include adapter boxes. See adapter box example in right column. 4 Light Traps and Kits Revision date: 03.15.17

Assembly Instructions: Vane Kit Components 1 ASSEMBLE LIGHT TRAP VANE KIT COMPONENTS ATTENTION: If kit number ends with letter A, light trap is preassembled. Skip Procedures 1 & 2 and continue with Procedure 3. Depending on size, vane kits are identified by one of these numbers: 113397, 113411, 113423, 113439, or 113450. Gather vane kit components. Review part descriptions for additional information. Complete these steps: 1. Unpack vanes keeping them in the same order as packed. 4. Slide a tube spacer onto each rod and add another vane. 5. Repeat Step 4 until all vanes are used. 2. Place one (1) rod cap nut firmly on one end of a rod. Use a nut driver (or similar tool) and a hammer to seat cap on rod. Repeat to install a cap on one end of each remaining rods. 6. After installing all vanes, install a cap nut on the end of each rod to secure final vane. 3. With assistance, stand rods upright with cap nuts at the bottom. Place one vane over all rods. Vane Spacer ATTENTION: Before installing cap nut, determine if a 3/8" spacer is needed. Vanes should be tight once final cap nut is installed. Cap Nut 7. Finally, turn assembled vane kit so vanes are vertical. 8. Continue by assembling vane kit frame. See Procedure 2. Light Traps and Kits Revision date: 03.15.17 5

2 ASSEMBLE Assembly Instructions: Vane Kit Frame LIGHT TRAP VANE KIT FRAME Gather parts: ATTENTION: If kit number ends with letter A, light trap is pre-assembled. Skip Procedures 1 & 2 and continue with Procedure 3. Complete these steps: 1. Use diagram below to attach aluminum angles to top and bottom frame panels first. Tighten all bolts. See ATTENTION note lower right. Sample Panel FAG304B 1/4" hex bolts FALF35B 1/4" locknuts FAME50B 1/4" flat washers FA4482B 1" Tek Screws B A Light trap frame top/bottom panels (2) Light trap frame side panels (2) Light trap aluminum angle (sides) (2) Light trap aluminum angle (top/bottom) (2) Light trap corner stabilizer brackets (4) A B FAG304B bolt (1) FALF35B locknut (1) Aluminum Angle FAME50B flat washers (2) NOTE: Aluminum angle for top and bottom panels will extend beyond panel edges as shown in diagram above and to the right (A). 2. Next attach aluminium angle to side panels. Tighten all bolts except those at each end (B). 3. Assemble frame as shown, tighten side panel bolts (B), and install 115280 corner brackets. Secure using FA4482B Tek screws. B TEK SCREW 4. Continue with next procedures as instructed. CORNER STABILIZER BRACKET [115280] A ATTENTION: Motorized shutter kits include a bottom aluminum angle with a small hole for the cable to pass through. Using a 7/16" bit, carefully drill through bottom frame panel after attaching bottom angle to panel. Use hole in angle as guide. Install 113392 grommet in hole. Grommet is present in these kits only: 113421, 113437, & 113448. A B 6 Light Traps and Kits Revision date: 03.15.17

Assembly Instructions: 113393, 113394, & 113419 (including A kits) 3 INSTALL SLANT FAN, SEPARATE SHUTTER ASSEMBLY, ADAPTER BO, & LIGHT TRAP Complete this procedure (Procedure 3) for kits containing an adapter box, shutters separate from fan, and a slant fan. (See page 3 for details.) For all other kits, complete either Procedure 4, Procedure 5, or Procedure 6. Complete these steps: 1. Measure fan and shutter and frame rough opening in end wall accordingly. (Frame tubing greater than 2" requires longer fasteners. Purchase locally if needed.) Tek screws are to secure to metal framing. Purchase different fasteners for framing that is wood or other material. 2. Set fan/shutter in place and install four (4) FA4482B Tek screws (one in each flange). Do not install in corners or in center position of any fan/shutter flange. These are mounting bolt positions. Support fan on outside if needed. See diagram at the lower-left of this page. 3. From inside the building, drill 3/8 holes for mounting bolts through shutter/fan flanges and frame in locations shown below (x's) for the correct fan size. Tek Screw Tek Screw Step 2 Tek Screw Step 3 Tek Screw Size 2' x 2': For kits that include 2' x 2' fans or shutters, drill a mounting hole near each corner: four (4) holes total. Support Size 3' x 3' or larger: For kits that include 3' x 3' or 4' x 4' fans or shutters, drill a hole in each corner and one between each corner as shown by 's in the diagram above: eight (8) holes total. Light Traps and Kits Revision date: 03.15.17 7

3 INSTALL Assembly Instructions: 113393, 113394, & 113419 (including A kits) SLANT FAN, SEPARATE SHUTTER ASSEMBLY, ADAPTER BO, & LIGHT TRAP continued 4. With assistance, center adapter box over fan and shutter opening and on top of Tek screws. 5. Hold box in place and use a level to ensure box is positioned correctly. 6. From outside end wall, run a drill bit through all mounting holes (Step 3) to mark these locations on the adapter box flange. Also, use a marking pen to mark the adapter box top to ensure correct repositioning. 7. Set adapter box on a flat surface and finish drilling the 3/8" mounting holes in locations marked in previous step. 8. Take the FA3182 elevator bolts and install one in each mounting hole by inserting from outside the end wall. (Ends of bolts will be inside the building flat head of bolt to the outside.) 9. Add a FAMF03B fender washer and 115161 jam nut to each bolt and tighten to secure fan/shutter. Remove Tek screws. Step 6 Step 7 Steps 8 & 9 Outside FA3182 FAMF03B Steps 4 & 5 up 115161 Nut Fan Fan Outside 8 Light Traps and Kits Revision date: 03.15.17

3 INSTALL Assembly Instructions: 113393, 113394, & 113419 (including A kits) SLANT FAN, SEPARATE SHUTTER ASSEMBLY, ADAPTER BO, & LIGHT TRAP continued 10. With assistance, lift box back into position to check mounting hole alignment with bolts. Ream mounting holes as needed to allow box to slide onto each mounting bolt. Once you are able to easily place adapter box in position, carefully set it on a flat surface with its mounting flange facing up. 11. Next, take the 111983 weather stripping and attach it to the adapter box flange. Make small cuts at each bolt hole to allow mounting bolts to pass through when box is lifted into position. ATTENTION: Weather stripping expands quickly. Have all 5/16" nuts, lock washers and flat washers ready to install before weather stripping is applied to box flange. Complete the next step before weather stripping is fully expanded. Do not apply stripping and allow it set for later installation. 12. With assistance, lift adapter box into place and set onto all mounting bolts. Install a FALB02B nut (a), FAMA37B lock washer (b), and FAME07B flat washer (c) onto each bolt. See diagram below. Bolts are accessible inside the adapter box. Step 11 b a c Weather Stripping Outside Adapter Box Fan Diagram shows installation of FALB02B nut (a), FAMA37B lock washer (b), and FAME07B flat washer (c). Weather Stripping Outside Adapter Box Fan 111983 Weather Stripping Mounting bolts are inside adapter box. Side of box has been removed to better show nut and washer position. Light Traps and Kits Revision date: 03.15.17 9

3 INSTALL 13. Tighten all nuts. Assembly Instructions: 113393, 113394, & 113419 (including A kits) SLANT FAN, SEPARATE SHUTTER ASSEMBLY, ADAPTER BO, & LIGHT TRAP continued Step 14 A A Weather Stripping Light Trap Gather parts: FAG304B 1/4" hex bolts FALF35B 1/4" locknuts FAME50B 1/4" flat washers 14. Attach light trap to adapter box. ATTENTION: Each 1/4" nut and bolt combination uses two (2) flat washers one installed against the bolt head and one installed against the locknut. For easier bolt installation, lift the light trap into position, align all bolt holes, and install fasteners. Assistants are required when installing the assembled light trap. Do not attempt to attach alone. 10 Light Traps and Kits Revision date: 03.15.17

4 Complete this procedure (Procedure 4) for kits containing a combined fan and shutter unit and an adapter box. (See page 3 for details.) For all other kits, complete either Procedure 3, Procedure 5, or Procedure 6. Complete these steps: Assembly Instructions: 113435 & 113436 (including A kits) INSTALL COMBINED FAN & SHUTTER UNIT, ADAPTER BO, & LIGHT TRAP 1. Measure fan and shutter and frame rough opening in end wall accordingly. (Frame tubing greater than 2" requires longer fasteners. Purchase locally if needed.) Tek screws are to secure to metal framing. Purchase different fasteners for framing that is wood or other material. 2. Set fan/shutter in place and install two (2) FA4482B Tek screws (one in each flange). Do not install in corners or in center position of any fan/shutter flange. These are mounting bolt positions. Support fan on outside if needed. 3. From inside the building, drill 3/8 holes for mounting bolts through flange and frame in locations shown below (x's) for the correct fan size. Tek Screw Step 3 Tek Screw Step 2 Tek Screw Step 3 Size 2' x 2': For kits that include 2' x 2' fans or shutters, drill a mounting hole near each corner: four (4) holes total. Light Traps and Kits Revision date: 03.15.17 11

4 INSTALL Assembly Instructions: 113435 & 113436 (including A kits) COMBINED FAN & SHUTTER UNIT, ADAPTER BO, & LIGHT TRAP continued 4. With assistance, center adapter box over fan and shutter opening and on top of Tek screws. 5. Hold box in place and use a level to ensure box is positioned correctly. 6. From outside end wall, run a drill bit through all mounting holes (Step 3) to mark these locations on the adapter box flange. Also, use a marking pen to mark the adapter box top to ensure correct repositioning. 7. Set adapter box on a flat surface, and finish drilling the 3/8" mounting holes in locations marked in previous step. 8. Take the FA3182 elevator bolts and install one in each mounting hole by inserting from outside the end wall. (Ends of bolts will be inside the building flat head of bolt to the outside.) 9. Add a FAMF03B fender washer and 115161 jam nut to each bolt and tighten to secure fan/shutter. Remove Tek screws. Step 6 Step 7 FAMF03B 115161 Nut Steps 8 & 9 Outside FA3182 Steps 4 & 5 Outside 12 Light Traps and Kits Revision date: 03.15.17

4 INSTALL Assembly Instructions: 113435 & 113436 (including A kits) COMBINED FAN & SHUTTER UNIT, ADAPTER BO, & LIGHT TRAP continued 10. With assistance, lift box back into position to check mounting hole alignment with bolts. Ream mounting holes as needed to allow box to slide onto each mounting bolt. Once you are able to easily place adapter box in position, carefully set it on a flat surface with its mounting flange facing up. 11. Next, take the 111983 weather stripping and attach it to the adapter box flange. Make small cuts at each bolt hole to allow mounting bolts to pass through when box is lifted into position. ATTENTION: Weather stripping expands quickly. Have all 5/16" nuts, lock washers and flat washers ready to install before weather stripping is applied to box flange. Complete the next step before weather stripping is fully expanded. Do not apply stripping and allow it set for later installation. 12. With assistance, lift adapter box into place and set onto all mounting bolts. Install a FALB02B nut (a), FAMA37B lock washer (b), and FAME07B flat washer (c) onto each bolt. See diagram below. Bolts are accessible inside the adapter box. b c Weather Stripping Outside Step 11 a Adapter Box Fan & Shutter Unit Diagram shows installation of FALB02B nut (a), FAMA37B lock washer (b), and FAME07B flat washer (c). Weather Stripping Outside 111983 Weather Stripping Adapter Box Mounting bolts are inside adapter box. Side of box has been removed to better show nut and washer position. Drill hole for chord. Insert chord. Seal hole using a piece of weather stripping. Light Traps and Kits Revision date: 03.15.17 13

4 INSTALL 13. Tighten all nuts. Assembly Instructions: 113435 & 113436 (including A kits) COMBINED FAN & SHUTTER UNIT, ADAPTER BO, & LIGHT TRAP continued A A Weather Stripping Gather parts: FAG304B 1/4" hex bolts FALF35B 1/4" locknuts FAME50B 1/4" flat washers 14. Attach light trap to adapter box. ATTENTION: Each 1/4" nut and bolt combination uses two (2) flat washers one installed against the bolt head and one installed against the locknut. For easier bolt installation, lift the light trap into position, align all bolt holes, and install fasteners. Assistants are required when installing the assembled light trap. Do not attempt to attach alone. 14 Light Traps and Kits Revision date: 03.15.17

5 INSTALL 1 Assembly Instructions: 113395, 113420, 115424, & 115425 (including A kits) MOTORIZED SHUTTER, ADAPTER BO, & LIGHT TRAP Complete this procedure (Procedure 5) for kits containing a motorized shutter and an adapter box. (See page 3 for details.) For all other kits, complete Procedure 3, Procedure 4, or Procedure 6. Consult instructions that shipped with shutter and shutter motor to install items. 2 Felt tape here. Outside Building Attach shutter to building frame using Tek screws spaced at 12" on-center around the perimeter. NOTE: Purchase other fasteners if frame is not metal. After installation, apply felt tape (104437) around perimeter of shutter flange. See white dashed line. Cut around Tek screws for best results. Using a 5/16" drill bit, pre-drill holes for Tek screws in mounting flange of adapter box. Space every 12" or so around flange perimeter. Mounting Flange Pre-drill mounting holes. View as seen from inside building. 3 NOTE: Tek screws are to attach components to metal framing. Do not use for other frame materials. FA4482B Consult instructions that shipped with shutter motor for motor installation details. ATTENTION: Use FA4482B Tek screws to secure adapter box to building. For easier installation, hold adapter box in position and mark mounting hole locations. Use a marker to make alignment lines on building and box frame. Remove adapter box and predrill Tek screw holes using a 1/16" bit to help start the self-tapping Tek screws. Lift adapter box into position, align marks and holes, and hold in place. Install Tek screws to secure box to building. Attach shutter motor bracket to adapter box. Attach shutter motor to bracket. Drill a hole in adapter box for electrical wires. When complete, seal hole with felt tape. 4 Enlist the services of an electrician to attach shutter motor to power. Adhere to all local and regional building codes. Using instructions that shipped with shutter motor, attach springs, chains, and motor arm. Test motor and shutter operation before installing the assembled light trap. Access to shutter motor is limited without removing light trap. See Step 5 (next page) for an additional view of installed motor. Light Traps and Kits Revision date: 03.15.17 15

5 INSTALL Assembly Instructions: 113395, 113420, 115424, & 115425 (including A kits) MOTORIZED SHUTTER, ADAPTER BO, & LIGHT TRAP continued Gather parts: FAG304B 1/4" hex bolts FALF35B 1/4" locknuts FAME50B 1/4" flat washers 5 6 Attach assembled light trap to adapter box using the fasteners listed above. NOTE: Each 1/4" nut and bolt combination uses two (2) flat washers one installed against the bolt head and one installed against the locknut. Drill hole for wiring. For easier bolt installation, lift the light trap into position, align all bolt holes, and install fasteners. ATTENTION: Consult instructions that shipped with shutter and shutter motor to install and adjust these items. 16 Light Traps and Kits Revision date: 03.15.17

6 INSTALL Assembly Instructions: 113421, 113437, 113448, 115426, 115427, & 115428 (including A kits) MOTORIZED SHUTTER & LIGHT TRAP Complete this procedure (Procedure 6) for kits containing a motorized shutter no adapter box. (See page 3 for details.) Consult the diagrams below and instructions that shipped with shutter and shutter motor to install shutter chains, cables, and motor. For all other kits, complete Procedure 3, Procedure 4, or Procedure 5. 1 2 Single Chain Connection Double Chain Connection Shutter Building Frame After installing shutter in wall opening, install shutter control chains and cable. See diagrams and instructions sent with shutter motor kit. Choose shutter design that matches shutter sent with kit. Secure all S-hooks by closing ends with pliers. Install shutter in opening. Use shims or blocks installed from the outside to hold shutter until light trap is attached. Shutter is attached using same Tek screws that secure light trap to frame. See Step 3 on next page. NOTE: Tek screws are to attach components to metal framing. Do not use for other frame materials such as wood or plastics. S-Hook Squeeze ends to secure. AS1002 Clamps AS1082 Thimble AS1002 Clamps AS1082 Thimble Purchase the appropriate fasteners locally or call customer service to purchase. Light Traps and Kits Revision date: 03.15.17 17

6 INSTALL 3 Assembly Instructions: 113421, 113437, 113448, 115426, 115427, & 115428 (including A kits) MOTORIZED SHUTTER & LIGHT TRAP continued Outside Building Light Trap Light Trap Cable Shutter Motor AS5075 Pulley ABOVE: Diagram shows shutter unit set in end frame. MIDDLE DIAGRAM: Verify that light trap assembly is positioned correctly with bottom aluminum angle toward the bottom. The bottom aluminum angle includes a small hole for cable to pass through. Using a 7/16" bit, carefully drill through bottom frame panel. Use hole in angle as guide. Install 113392 grommet in hole. With assistance, lift vane assembly and thread cable through grommet. Attach vane assembly to frame using FA4482B Tek screws. 113392 Grommet Enlist the services of an electrician to attach shutter motor to power. Adhere to all local and regional building codes. AS1002 Clamps ATTENTION: Install two (2) Tek screws at first and test shutter operation by pulling on cable. Shutters should open and close easily and without binding. Adjust as needed if shutters do not operate smoothly. RIGHT DIAGRAMS: Use cable length to judge positions of pulley and shutter motor. Space pulley and motor so cable clamps do not touch pulley during operation when cable is attached to motor arm. Secure to frame using FA4482B Tek screws. Use the instructions sent with shutter motor to properly set motor arm position. Thread cable through hole in motor arm and secure using two (2) clamps. Supply power to motor and test operation. 18 Light Traps and Kits Revision date: 03.15.17

113449/113449A Breathable Wall Light Trap with Frame: 2' x 2' 28 5 8 " ATTENTION: To assemble this item only, complete Procedures 1 & 2. 28 3 8 " 113453 113451 FAG304B bolt (1) FALF35B locknut (1) FAME50B flat washers (2) FA4482B Tek Screws (28) FRONT VIEW 11 7 16 " 115280 113452 113454 TOWARD INSIDE OF BUILDING SIDE VIEW 113450 113455 Light Traps and Kits Revision date: 03.15.17 19

113438/113438A Breathable Wall Light Trap with Frame: 3' x 3' 40 5 8 " ATTENTION: To assemble this item only, complete Procedures 1 & 2. 113442 113440 FAG304B bolt (1) FALF35B locknut (1) FAME50B flat washers (2) 40 3 8 " FA4482B Tek Screws (28) 115280 FRONT VIEW 11 7 16 " 113441 113443 TOWARD INSIDE OF BUILDING 113439 SIDE VIEW 113444 20 Light Traps and Kits Revision date: 03.15.17

113422/113422A Breathable Wall Light Trap with Frame: 4' x 4' 52 5 8 " ATTENTION: To assemble this item only, complete Procedures 1 & 2. 113426 113424 FAG304B bolt (1) FALF35B locknut (1) FAME50B flat washers (2) 52 3 8 " FA4482B Tek Screws (28) FRONT VIEW 11 7 16 " 115280 113425 113427 TOWARD INSIDE OF BUILDING 113423 SIDE VIEW 113428 Light Traps and Kits Revision date: 03.15.17 21

113410/113410A Breathable Wall Light Trap with Frame: 5' x 5' 64 5 8 " ATTENTION: To assemble this item only, complete Procedures 1 & 2. 64 3 8 " 113414 113412 FAG304B bolt (1) FALF35B locknut (1) FAME50B flat washers (2) FA4482B Tek Screws (28) TOWARD INSIDE OF BUILDING FRONT VIEW 11 7 16 " 115280 113413 113415 113411 SIDE VIEW 22 Light Traps and Kits Revision date: 03.15.17

113396/113396A Breathable Wall Light Trap with Frame: 6' x 6' 76 5 8 " ATTENTION: To assemble this item only, complete Procedures 1 & 2. 113400 113398 FAG304B bolt (1) FALF35B locknut (1) FAME50B flat washers (2) 76 3 8 " FA4482B Tek Screws (28) FRONT VIEW TOWARD INSIDE OF BUILDING 11 7 16 " 115280 113399 113401 SIDE VIEW 113397 Light Traps and Kits Revision date: 03.15.17 23