Study Guide: Agriscience Technology Mechanics Matching - Safety Colors: 1. Danger A. Yellow 2. Information B. Green 3. Safety C. Red 4. Warning D. Blue 5. Caution E. Orange Matching - Tool Categories 6. A tool used to measure or mark wood, metal, and other materials. A. Boring tool 7. A tool used to cut, chop, saw, or remove material. B. Layout tool 8. A tool used to turn nuts, bolts, or screws. C. Fastener 9. Any device used to hold two or more pieces of material together or in one place. D. Driving tool 10. A tool used to move another tool or object. E. Cutting tool 11. Any device used to turn up, loosen, or remove earth (dirt). F. Digging tool 12. A tool used to make holes or change the size or shape of holes. G. Holding tool 13. A tool used to grip wood, metal, plastic, and other materials. H. Turning tool Matching Classes of Fire 14. Class A A. Electrical equipment (electrical fire) 15. Class B B. Ordinary combustibles (wood, paper, trash) 16. Class C C. Flammable liquids (fuel, grease, paint) 17. Class D D. Combustible metals (metals that burn)
18. What does OSHA stand for? A. Occupational Safety Hat Association B. Occupational Safety and Health Act C. Optimum Safety and Health Association D. Occasional Safety Hat Act 19. What is the standard unit of sound? A. decibels (db) B. photons C. waves D. joules 20. Hearing damage can occur is excessively exposed to noise above decibels. A. 20 B. 35 C. 70 D. 90 21. Which body parts are most often injured in shop accidents? A. arms and hand B. feet and legs C. face and head D. torso (chest, stomach, back) 22. What are the three parts of the fire triangle? A. fuel, heat, oxygen B. electrical charge, heat, carbon dioxide C. wood, fire, nitrogen D. electricity, water, heat 23. A screw is. A. driven into the material with a hammer B. a fastener with a threaded nut C. a fastener with threads that is inserted with a screwdriver, drill, or impact wrench D. a device with a threaded hole. 24. Explain the difference between the NOMINAL size and ACTUAL size of lumber. (You can use a 2 x 4 as an example.)
25. When should safety glasses be worn in the mechanics laboratory/shop? A. only when the instructor tells you to B. only when the job is dangerous to your eyes C. only when using woodworking tools D. at all times when you are working in the shop 26. is a safe method of securing your work. A. Holding with your hands B. Having a partner hold your work C. Placing work in a vise D. All of the above 27. What tool would be used to measure the outside diameter of a cylinder? A. dividers B. outside calipers C. inside calipers D. micrometer 28. A clean, organized shop reduces the risk of. A. damaging projects B. losing tools C. injuring people D. all of the above 29. What lowercase letter is used to indicate nail size? A. d B. z C. b D. p 30. A nail has a small head that is hidden when nailed into finished wood. A. common B. finishing C. drywall D. sinker 31. The Z87.1 logo on safety glasses means that they are. A. top quality B. first quality C. expensive D. industrial quality
32. Store oily rags in a. A. paper box B. pile in the corner C. closed metal can D. laundry basket 33. A should be used to mark wood. A. pencil B. pen C. marker D. any of these 34. Which is not a type of file? A. round B. half-round C. triangle D. diagonal 35. Which Phillips screwdriver would be the largest? A. Number 1 B. Number 2 C. Number 3 D. Number 4 36. Which of the following will add color to the wood? A. polyurethane B. stain C. varnish D. wax 37. Which of the following is used to make a mark on a metal surface? A. dividers B. scratch awl C. protractor D. marking gauge 38. A try square can be used to draw a. A. 90 degree line across a board B. 30 degree line across a board C. Either a 90 degree or 30 degree line across a board D. none of these
39. Which tool is NOT used to measure angles? A. protractor B. framing square C. combination square D. inside calipers 40. When sawing a board, the saw removes wood and leaves an opening called a. A. kerf B. leader line C. epoxy D. pivot 41. Which saw is not suitable for cutting curves? A. back saw B. coping saw C. compass saw D. keyhole saw 41. Which kind of saw is used to cut across the grain? A. crosscut saw B. rip saw C. hacksaw D. coping saw 42. The tool used to push nail heads below the surface of wood is a nail. A. driver B. press C. punch D. set 43. Tools are classified by. A. use B. color C. construction D. origin 44. When cutting with a saw, you should always cut. A. on the line B. to the good/usuable side of the line C. to the waste side of the line D. half an inch from the line
45. The grain in lumber is caused by. A. annual rings B. age of the board C. special drying techniques D. stain 46. Which of the following sandpapers will have the smoothest finish? A. 280 B. 220 C. 100 D. 80 47. Which of the following formulas will calculate board feet? A. T x W x L 12 B. T x W x L 24 C. T x W x L 12 D. T x W x L 144 48. How many board feet are in a piece of lumber that is 2 x 8 x 10? 49. How many board feet are in a piece of lumber that is 1 x 6 x 8? 50. The tool most commonly used to transfer angles is a. A. combination square B. T bevel C. framing square D. dividers
51. A board foot is based on the. A. number of cubic inches B. length and width only C. length in inches x width in inches x thickness in inches divided by 12 D. length in feet x width in inches x thickness in inches divided by 12 52. A variable speed tool is one that will run. A. a long time without damage B. backwards as well as forwards C. in hot locations D. at different speeds 53. When sanding with an electric sander, you should sand. A. against the grain B. across the grain C. with the grain D. only on one end 54. The names given to lumber sizes ( two by four ) represent the. A. actual size B. nominal size C. size after being planed D. size before being planed 55. Using a vise or clamp will help. A. secure your work B. prevent an accident C. both A and B D. neither A or B 56. An example of unsafe shoes for the laboratory would be: A. flip-flops B. tennis shoes C. dress shoes D. hiking boots 57. Use only files that are equipped with. A. sandpaper B. handles C. batteries D. safety switches
58. A device for drawing circles is a. A. outside caliper B. framing square C. compass D. protractor 59. Wood screws are sized by numbers such as #6, #8, #12, etc. The numbers refer to. A. length of wood screw B. diameter of wood screw C. type of screwdriver needed D. none of the above 60. The terminology to describe nail size is. A. penny B. nickel C. dime D. bit 61. After using oil based paints and stains, you should clean the brushes with. A. paint thinner B. water 62. An example of a holding tool would be. A. C-clamp B. bar clamp C. block clamp D. All of the above