PT6 Series Amp Adjustable Positive Step-down Integrated Switching Regulator SLTS29A (Revised 6/3/2) 9% Efficiency Adjustable Output Voltage Internal Short Circuit Protection Over-Temperature Protection On/Off Control (Ground Off) Small SIP Footprint Meets Requirements for FCC Part 5; Class B limits for Radiated Emissions Wide Input Range The PT6 Series is a line of High-Performance Amp, 2-Pin SIP (Single In-line Package) Integrated Switching Regulators (ISRs) designed to meet the on-board power conversion needs of battery powered or other equipment requiring high efficiency and small size. This high performance ISR family offers a unique combination of features combining 9% typical efficiency with open-collector on/off control and adjustable output voltage. Quiescent current in the shutdown mode is less than µa. Standard Application V O ADJ V IN INH C 2,3,4 Q Specifications 2 PT6 5,6,7,8 9,, C2 V OUT C = Optional µf ceramic Q = NFET C 2 = Required µf electrolytic + Pin-Out Information Pin Function Inhibit (3V max) 2 V in 3 V in 4 V in 5 GND 6 GND 7 GND 8 GND 9 V out V out V out 2 V out Adj Ordering Information PT6 = +5 Volts PT62 = +3.3 Volts PT63 = +2 Volts PT Series Suffix (PT234X) Case/Pin Configuration Vertical Through-Hole Horizontal Through-Hole Horizontal Surface Mount Characteristics PT6 SERIES (T a =25 C unless noted) Symbols Conditions Min Typ Max Units Output Current I o Over V in range.*. A Short Circuit Current I sc V in = V in min 3.5 Apk Input Voltage Range V in. I o. A V o = 3.3V 9 26 V (Note: inhibit function cannot V o = 5V 9 3/38** V be used with above 3V.) V o = 2V 6 3/38** V Output Voltage Tolerance V o Over V in Range, I o =. A T a = C to +6 C Pkg Style 2 N A C ±. ±2. %Vo Line Regulation Reg line Over V in range ±.25 ±.5 %V o Load Regulation Reg load. I o. A ±.25 ±.5 %V o V o Ripple/Noise V n V in =V in min, I o =. A ±2 %V o Transient Response t tr 5% load change 2 µsec with C o = µf V os V o over/undershoot 5. %V o Efficiency η V in=9v, I o=.5a, V o=3.3v 84 % V in =9V, I o V o =5V 89 % V in=6v, I o=.5a, V o=2v 9 % Switching Frequency ƒ o Over V in and I o ranges 4 5 6 khz Shutdown Current I sc V in = 5V µa Quiescent Current I nl I o = A, V in =V ma Output Voltage V o Below V o See Application Notes. Adjustment Range Above V o Absolute Maximum Operating Temperature Range T a -4 +85 C Recommended Operating T a Free Air Convection, V o = 3.3V -4 +85*** Temperature Range (4-6LFM) V o= 5V -4 +85*** C V in=24v, I o=.75a V o= 2V -4 +8*** Thermal Resistance θ ja Free Air Convection V o = 3.3V 5 (4-6LFM) V o = 5V 4 C/W V o = 2V 4 Storage Temperature T s -4 +25 C Mechanical Shock Per Mil-STD-883D, Method 22.3 msec, Half Sine, mounted to a fixture 5 G s Mechanical Vibration Per Mil-STD-883D, Method 27.2 2-2 Hz, Soldered in a PC board G s Weight 5. grams * ISR will operate down to no load with reduced specifications. ** Input voltage cannot exceed 3V when the inhibit function is used. ***See Thermal Derating chart. Note: The PT6 Series requires a µf electrolytic or tantalum output capacitor for proper operation in all applications.
PT6 Series Typical Characteristics Amp Adjustable Positive Step-down Integrated Switching Regulator PT62, 3.3 VDC (See Note ) PT6, 5. VDC (See Note ) PT63, 2. VDC (See Note ) Efficiency vs Output Current Efficiency vs Output Current Efficiency vs Output Current 9 9 9 Efficiency - % 8 7 6 9.V 2.V 5.V 8.V 26.V Efficiency - % 8 7 6 9.V 2.V 8.V 24.V 3.V 38.V Efficiency - % 8 7 6 6.V 2.V 24.V 3.V 38.V 5 5 5 4.2.4.6.8 4.2.4.6.8 4.2.4.6.8 Ripple vs Output Current Ripple vs Output Current Ripple vs Output Current 9 8 4 8 6 35 Ripple-(mV) 7 6 5 4 3 26.V 8.V 5.V 2.V 9.V Ripple-(mV) 4 2 8 6 38.V 3.V 24.V 8.V 2.V 9.V Ripple-(mV) 3 25 2 5 38.V 3.V 24.V 2.V 6.V 2 4 2 5.2.4.6.8.2.4.6.8.2.4.6.8 Thermal Derating (T a) (See Note 2) Thermal Derating (T a) (See Note 2) Thermal Derating (T a) (See Note 2) 7 C 5 C 6 C.8 85 C.8 7 C.8 7 C 85 C.6.4.6.4.6.4 85 C.2.2.2 9 2 5 8 2 24 27 9 2 5 8 2 24 27 3 33 36 39 6 8 2 22 24 26 28 3 32 34 36 38 -(Volts) (n -(Volts) -(Volts) Power Dissipation vs Output Current Power Dissipation vs Output Current Power Dissipation vs Output Current.4 2 PD-(Watts).9.8.7.6.5.4.3 26.V 8.V 5.V 2.V 9.V PD-(Watts).2.8.6.4 38.V 3.V 24.V 8.V 2.V 9.V PD-(Watts).8.6.4.2.8.6 38.V 3.V 24.V 2.V 6.V.2..2.4.2.2.4.6.8.2.4.6.8.2.4.6.8 Note : All data listed in the above graphs, except for derating data, has been developed from actual products tested at 25 C. This data is considered typical data for the ISR. Note 2: Thermal derating graphs are developed in free air convection cooling of 4-6 LFM. (See Thermal Application Notes.)
Application Notes PT6/62/63 Series Adjusting the Output Voltage of Power Trends Wide Input Range Bus ISRs Figure The output voltage of the Power Trends Wide Input Range Series ISRs may be adjusted higher or lower than the factory trimmed pre-set voltage with the addition of a single external resistor. Table accordingly gives the allowable adjustment range for each model for either series as V a (min) and V a (max). Adjust Up: An increase in the output voltage is obtained by adding a resistor R2, between pin 2 (V o adjust) and pins 5-8 (GND). C µf Ceramic (Optional) 2,3,4 PT6/62/63 GND 5,6,7,8 Vo(adj) 2 Vo R2 Adjust Up 9,, (R) Adj Down C2 µf (Req d) + Vo Adjust Down: Add a resistor (R), between pin 2 (V o adjust) and pins 9-(V out ). Refer to Figure and Table 2 for both the placement and value of the required resistor; either (R) or R2 as appropriate. Notes:. Use only a single % resistor in either the (R) or R2 location. Place the resistor as close to the ISR as possible. 2. Never connect capacitors from V o adjust to either GND or V out. Any capacitance added to the V o adjust pin will affect the stability of the ISR. 3. Adjustments to the output voltage may place additional limits on the maximum and minimum input voltage for the part. The revised maximum and minimum input voltage limits must comply with the following requirements. Note that the minimum input voltage limits are also model dependant. V in (max) = (8 x V a )V or * 3/38V, whichever is less. * Limit is 3V when inhibit function is active. PT6xx/PT6xx series: V in (min) = (V a + 4)V or 9V, whichever is greater. PT6x2x series: V o <V; V in (min) = (V a + 2.)V or 7.V, whichever is greater. V o V; V in (min) = (V a + 2.5)V The values of (R) [adjust down], and R2 [adjust up], can also be calculated using the following formulae. (R) = R2 = R o (V a.25) V o V a kω.25 R o kω V a V o Where: V o = Original output voltage V a = Adjusted output voltage R o = The resistance value fromtable Table ISR ADJUSTMENT RANGE AND FORMULA PARAMETERS Adc Rated PT62 PT6 PT63 2Adc Rated PT623 PT622 PT624 3Adc Rated PT633 PT632 PT634 Vo (nom) 3.3 5. 5. 2. Va (min).89.88 2.8 2.43 Va (max) 6.7.25 8.5 22.2 Ro (kω) 66.5 5. 9.9 243.
Application Notes continued PT6/62/63 Series Table 2 ISR ADJUSTMENT RESISTOR VALUES Adc Rated PT62 PT6 PT63 2Adc Rated PT623 PT622 PT624 3Adc Rated PT633 PT632 PT634 V o (nom) 3.3 5. 5. 2. V a (req.d).9 (3.9)kΩ (3.5)kΩ 2. (38.4)kΩ (37.5)kΩ 2. (47.)kΩ (44.)kΩ 2.2 (57.4)kΩ (5.9)kΩ (3.8)kΩ 2.3 (69.8)kΩ (58.3)kΩ (35.4)kΩ 2.4 (85.)kΩ (66.3)kΩ (4.2)kΩ 2.5 (4.)kΩ (75.)kΩ (45.5)kΩ (32.)kΩ 2.6 (28.)kΩ (84.4)kΩ (5.)kΩ (34.9)kΩ 2.7 (6.)kΩ (94.6)kΩ (57.3)kΩ (37.9)kΩ 2.8 (26.)kΩ (6.)kΩ (64.)kΩ (4.9)kΩ 2.9 (274.kΩ (8.)kΩ (7.4)kΩ (44.)kΩ 3. (388.)kΩ (3.)kΩ (79.5)kΩ (47.3)kΩ 3. (65.)kΩ (46.)kΩ (88.5)kΩ (5.5)kΩ 3.2 (3.)kΩ (63.)kΩ (98.5)kΩ (53.8)kΩ 3.3 (8.)kΩ (.)kω (57.3)kΩ 3.4 83.kΩ (22.)kΩ (22.)kΩ (6.8)kΩ 3.5 46.kΩ (225.)kΩ (36.)kΩ (64.3)kΩ 3.6 227.kΩ (252.)kΩ (53.)kΩ (68.)kΩ 3.7 28.kΩ (283.)kΩ (7.)kΩ (7.7)kΩ 3.8 66.kΩ (39.)kΩ (93.)kΩ (75.6)kΩ 3.9 39.kΩ (36.)kΩ (29.)kΩ (79.5)kΩ 4. 9.kΩ (43.)kΩ (25.)kΩ (83.5)kΩ 4. 4.kΩ (475.)kΩ (288.)kΩ (87.7)kΩ 4.2 92.4kΩ (533.)kΩ (335.)kΩ (9.9)kΩ 4.3 83.kΩ (654.)kΩ (396.)kΩ (96.3)kΩ 4.4 75.6kΩ (788.)kΩ (477.)kΩ (.)kω 4.5 69.3kΩ (975.)kΩ (59.)kΩ (5.)kΩ 4.6 63.9kΩ (26.)kΩ (76.)kΩ (.)kω 4.7 59.4kΩ (73.)kΩ (5.)kΩ (5.)kΩ 4.8 55.4kΩ (6.)kΩ (2.)kΩ 4.9 52.kΩ (25.)kΩ 5. 48.9kΩ (3.)kΩ 5. 46.2kΩ 88.kΩ 4.kΩ (36.)kΩ 5.2 43.8kΩ 937.kΩ 568.kΩ (4.)kΩ 5.3 4.6kΩ 625.kΩ 379.kΩ (47.)kΩ 5.4 39.6kΩ 469.kΩ 284.kΩ (53.)kΩ 5.5 37.8kΩ 375.kΩ 227.kΩ (59.)kΩ 5.6 36.kΩ 33.kΩ 89.kΩ (65.)kΩ 5.7 34.6kΩ 268.kΩ 62.kΩ (72.)kΩ 5.8 33.3kΩ 234.kΩ 42.kΩ (78.)kΩ 5.9 32.kΩ 28.kΩ 26.kΩ (85.)kΩ 6. 3.8kΩ 88.kΩ 4.kΩ (92.)kΩ R = (Blue) R2 = Black ISR ADJUSTMENT RESISTOR VALUES (Cont) Adc Rated PT6 PT63 2Adc Rated PT622 PT624 3Adc Rated PT632 PT634 V o (nom) 5. 5. 2. V a (req.d) 6.2 56.kΩ 94.7kΩ (27.)kΩ 6.4 34.kΩ 8.2kΩ (223.)kΩ 6.6 7.kΩ 7.kΩ (24.)kΩ 6.8 4.kΩ 63.kΩ (259.)kΩ 7. 93.8kΩ 56.8kΩ (279.)kΩ 7.2 85.2kΩ 5.6kΩ (3.)kΩ 7.4 78.kΩ 47.3kΩ (325.)kΩ 7.6 72.kΩ 43.7kΩ (35.)kΩ 7.8 67.kΩ 4.6kΩ (379.)kΩ 8. 62.5kΩ 37.9kΩ (4.)kΩ 8.2 58.6kΩ 35.5kΩ (444.)kΩ 8.4 55.kΩ 33.4kΩ (483.)kΩ 8.6 52.kΩ (525.)kΩ 8.8 49.3kΩ (573.)kΩ 9. 46.9kΩ (628.)kΩ 9.5 4.7kΩ (82.)kΩ. 37.5kΩ (6.)kΩ.5 34.kΩ (5.)kΩ. 3.3kΩ.5 2. 2.5 68.kΩ 3. 34.kΩ 3.5 23.kΩ 4. 52.kΩ 4.5 22.kΩ 5..kΩ 5.5 86.8kΩ 6. 75.9kΩ 6.5 67.5kΩ 7. 6.8kΩ 7.5 55.2kΩ 8. 5.6kΩ 8.5 46.7kΩ 9. 43.4kΩ 9.5 4.5kΩ 2. 38.kΩ 2.5 35.7kΩ 2.5 33.8kΩ 2.5 32.kΩ 22. 3.4kΩ
Application Notes PT6/62/63 Series Using the Inhibit Function on Power Trends Wide Input Range Bus ISRs For applications requiring output voltage On/Off control, the 2pin ISR products incorporate an inhibit function. The function has uses in areas such as battery conservation, power-up sequencing, or any other application where the regulated output from the module is required to be switched off. The On/Off function is provided by the Pin (Inhibit) control. The ISR functions normally with Pin open-circuit, providing a regulated output whenever a valid source voltage is applied to V in, (pins 2, 3, & 4). When a low-level 2 ground signal is applied to Pin, the regulator output will be disabled. Figure shows an application schematic, which details the typical use of the Inhibit function. Note the discrete transistor (Q). The Inhibit control has its own internal pull-up with a maximum open-circuit voltage of 8.3VDC. Only devices with a true open-collector or open-drain output can be used to control this pin. A discrete bipolar transistor or MOSFET is recommended. Equation may be used to determine the approximate current drawn by Q when the inhibit is active. Equation I stby =V in 55kΩ ± 2% Figure V in Inh C, µf (Optional) PT6/62/63 2,3,4 9,, Vo Inh* GND Vo(adj) 5,6,7,8 2 Q BSS38 C2 µf + V out Turn-On Time: The output of the ISR is enabled automatically when external power is applied to the input. The Inhibit control pin is pulled high by its internal pull-up resistor. The ISR produces a fully regulated output voltage within -msec of either the release of the Inhibit control pin, or the application of power. The actual turn-on time will vary with the input voltage, output load, and the total amount of capacitance connected to the output Using the circuit of Figure, Figure 2 shows the typical rise in output voltage for the PT6 following the turn-off of Q at time t =. The waveform was measured with a 9Vdc input voltage, and 5-Ohm resistive load. Notes:. The Inhibit control logic is similar for all Power Trends modules, but the flexibility and threshold tolerances will be different. For specific information on the inhibit function of other ISR models, consult the applicable application note. 2. Use only a true open-collector device (preferably a discrete transistor) for the Inhibit input. Do Not use a pull-up resistor, or drive the input directly from the output of a TTL or other logic gate. To disable the output voltage, the control pin should be pulled low to less than +.5VDC. 3. When the Inhibit control pin is active, i.e. pulled low, the maximum allowed input voltage is limited to +3Vdc. 4. Do not control the Inhibit input with an external DC voltage. This will lead to erratic operation of the ISR and may over-stress the regulator. 5. Avoid capacitance greater than 5pF at the Inhibit control pin. Excessive capacitance at this pin will cause the ISR to produce a pulse on the output voltage bus at turn-on. 6. Keep the On/Off transition to less than µs. This prevents erratic operation of the ISR, which can cause a momentary high output voltage. Figure 2 6 5 4 Vo (Vdc) 3 2 -.2.2.4.6.8 t (milli-secs)
IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. Customers are responsible for their applications using TI components. In order to minimize risks associated with the customer s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI s publication of information regarding any third party s products or services does not constitute TI s approval, warranty or endorsement thereof. Copyright 2, Texas Instruments Incorporated