Test Report issued under the responsibility of: STAYER IBÉRICA S.A TEST REPORT Safety of Transportable Motor-Operated Power Tools REPORT IDS TR_POTENZA160_SEG_01 Report Reference No. : TR_POTENZA160_SEG_01 Date of issue... : 2013/08/01 Total number of pages... 88 Testing Laboratory... : Address... : Applicant s name... : Address... : QC Dept STAYER IBERICA S.A. C/ Sierra de Cazorla 7, 28320 Pinto, Madrid, España. Stayer Ibérica S.A. C/ Sierra de Cazorla 7, 28320 Pinto, Madrid, España. Test specification: Standard... : EN 60974-1:2012, EN 60974-10:2007 Test procedure... : Non-standard test method..: 60974_1_ST certified by DNV European Commission Notified Body 0434 NOBO number N Test Report Form No.... : A Test Report Form(s) Originator... : CQC Master TRF... : Dated 2009-07 Copyright 2007 IEC System for Conformity Testing and Certification of Electrical Equipment (IECEE), Geneva, Switzerland. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as copyright owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. If this Test Report Form is used by non-iecee members, the IECEE/IEC logo and the reference to the CB Scheme procedure shall be removed. This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02. Test item description...: Trade Mark... : Manufacturer... : INVERTER DC ARC WELDING EQUIPMENT STAYER WELDING Same as applicant Model/Type reference... : POTENZA 160 Ratings... : 160A -- 60% Duty cycle 230 Vac; 1pH - 50/60 Hz; Class I; IP21; POTENZA 160: Effective supply current: Imax=28 A; Ieff=19 A Max. Welding current: 160 A
Page 2 of 5 Testing procedure and testing location: Testing procedure...: Testing procedure: WMT Witnessed by (+ signature)... : Approved by (+ signature)... : ISO9001 PE/11 Reynaldo Armas Simon Diaz C/ Sierra de Cazorla 7, 28320 Pinto, Madrid, España Testing procedure: SMT Supervised by (+ signature)... : Testing location/ address...: Testing procedure: RMT Supervised by (+ signature)... : A
Page 3 of 5 Summary of testing: The appliance complies with the requirements of the standards: EN 60974-1:2012 Tests performed (name of test and test clause): All tests according to EN 60974-1:2012 EN 60974-10:2007 Testing location: C/ Sierra de Cazorla 7, 28320 Pinto, Spain Summary of compliance with National Differences: No national differences A
Page 4 of 5 Copy of marking plate Test item particulars... : Classification of installation and use... : Class I Supply Connection... : Supply cord fitted whit a plug Possible test case verdicts: - test case does not apply to the test object...: N/A - test object does meet the requirement...: P (Pass) - test object does not meet the requirement...: F (Fail) Testing...: Date of receipt of test item...: April 14, 2013 Date (s) of performance of tests...: April 14 2013 May 25 2013 A
Page 5 of 5 General remarks: The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory. "(See Enclosure #)" refers to additional information appended to the report. "(See appended table)" refers to a table appended to the report. Throughout this report a comma (point) is used as the decimal separator. General product information: Electric arc inverter welding machine. 160A, 60%, duty cycle with 77 Vdc of no load voltage. A