10/22/2014 Sapper Monitor rm ollection ouble Monitor rm Kit (Standard and Sapper 50 rms) Installation Instructions SM-K
Step 1: ttach Mount to Work Surface, Slat wall or Wall Two-Piece Table lamp, eavy uty Table lamp and eep Table lamp Mounts llen wrenches (in inches) lamp lower to upper jaw 5/32 () lamp to mast 5/16 () lamp compression screws 1/4 () or installation on a work surface positioned against a wall or panel: 1. Remove clamp lower jaw (), by removing both clamping screws () and both lower jaw mounting screws (). 2. ssemble mast () to clamp upper jaw (), by inserting the pin () on clamp () into hole in bottom of mast (). Secure mast (), to clamp (), with screw (). Tighten securely. Slide upper jaw () down along edge of desk surface. 3. eneath work surface, replace lower jaw (), by reinstalling (2) mounting screws (), (2) clamping screws () and (2) pressure discs (). Tighten both clamping screws () with pressure discs () in place on top of clamping screws (). o not over-tighten as this may damage the table surface. or installation on open edge of work surface: 1. ssemble mast () to clamp (), by inserting the pin () on clamp () into hole in bottom of mast (). Secure mast (), to clamp (), with screw (). Tighten securely. 2. Slide table clamp () onto edge of desk surface. With pressure discs () in place on top of clamping screws (), tighten both clamp screws (). o not over-tighten as this may damage the table surface. If clamp opening needs adjustment to accommodate thicker or thinner desk top, follow instructions to the left. Note: The eep Table lamp (ig. 1) is one piece and can only be mounted on open edge of worksurface as described above. eep Table lamp ig. 1 work surface Two-Piece and eavy uty Table lamps work surface 2
rommet Mount ixed Table Mount 3/4 open end wrench () 3/4 open end wrench () rill 1. hoose the orientation of grommet mount plate () on the work surface. Remove grommet cover and any moveable grommet liner. 2. Place the grommet mount plate () over the grommet hole, with ½ hole for the threaded connection stud () inside the grommet hole. djust placement of the grommet mount plate () so it equally overhangs the grommet hole. 3. Thread the threaded connection stud () into the bottom of the mast () using all available threads. Pass the threaded connection stud () though the ½ hole in grommet mount plate () and through the grommet hole. 4. eneath the desk, slide the mounting bar () and washer () onto the threaded connection stud (). Thread nut () onto threaded connection stud (). Orient the mast with the top of the slope () facing the user. Tighten nut () using a wrench. o not over-tighten as this may damage the table surface. 1. stablish desired mounting location. rill a 17/32 diameter hole, through the table surface/desk top. ssemble disc (), lock washer () and nut (), onto stud (). 2. rom beneath the desk, push top of stud (), up through hole. Slide second disc () over stud (). Thread mast () onto stud using all available threads in mast (). 3. Orient the mast (), with the top of the slope facing the user (see illustration). Tighten nut (). o not overtighten as this may damage the table surface. work surface work surface 3
Step 1: ttach Mount to Work Surface, Slat wall or Wall rinion Open Table enter hannel Mount ividends orizon enching Mount llen Wrenches (in inches and mm s) rinion Open Table (OT) enter hannel Mount to Mast 5/16 () rinion Open Table (OT) enter hannel Mount to lex-link Nuts (5mm) () llen wrenches (in inches) Mount to mast - 5/16 () ompression Screws - 1/4 () 1. ssemble mast () to OT enter hannel Mount (), by inserting the pin () on the OT enter hannel Mount () into the hole in the bottom of the mast (). Secure mast () to OT enter hannel Mount () with screw (). Tighten securely. 2. Insert (2) flex-link nuts () into top center channel of OT by pushing one side (long edge) down into the channel until the following edge/side drops into the channel. 3. Slide flex-link nuts () to desired mounting location. ssemble OT enter hannel Mount () to flex-link nuts () with screws (), tighten securely. 1. Remove both ividends orizon enching Mount lower jaws (), by removing both clamping screws () and both lower jaw mounting screws (). 2. ssemble mast () to ividends orizon enching Mount (), by inserting the pin () on ividends orizon enching Mount () into hole in bottom of mast (). Secure mast (), to ividends orizon enching Mount (), with screw (). Tighten securely. Slide ividends orizon enching Mount () down along edge of desk surface. 3. eneath work surface, replace both lower jaws (), by reinstalling (2) mounting screws (), (2) clamping screws () and (2) pressure discs (). Tighten both clamping screws () with pressure discs () in place on top of clamping screws (). o not over-tighten as this may damage the table surface. 4
ntenna Table enter eam enter Mount ntenna Table enter eam Side Mount llen wrenches (in inches and mm s) ntenna Table enter eam enter Mount to Mast 5/16 () ntenna Table enter eam enter Mount to lex-link Nuts (5mm) () llen wrenches (in inches and mm s) ntenna Table enter eam Side Mount to Mast 1/4 () ntenna Table enter eam Side Mount to lex-link Nuts Phillips Screwdriver () 1. ssemble mast () to ntenna Table enter eam enter Mount (), by inserting the pin () on the ntenna Table enter eam Mount () into the hole in the bottom of the mast (). Secure mast () to ntenna Table enter eam enter Mount () with screw (). Tighten securely. 2. Insert (2) flex-link nuts () into top center beam of ntenna ig Table by pushing one side (long edge) down into the beam until the following edge/side drops into the channel. 3. Slide flex-link nuts () to desired mounting location. ssemble ntenna Table enter eam enter Mount () to flex-link nuts () with screws (), tighten securely. 1. ssemble mast () to ntenna Table enter eam Side Mount (), by inserting the curved ribs () of enter eam Side Mount () into voids of mast (). Secure mast to ntenna Table enter eam Side Mount () with screw (). Tighten securely. 2. Insert (2) flex-link nuts () into side channel of beam of ntenna ig Table by pushing one side (long edge) down into the channel until the following edge/side drops into the channel. 3. Slide flex-link nuts () to desired mounting location. ssemble ntenna Table enter eam Side Mount () by dropping bracket on side flange of beam () and securing with screws (). Tighten securely. 5
Slat Wall Mast Mount Wall Mast Mount (for rchitectural Walls Only) llen wrenches (in inches) Slat wall Mounted Mast racket to Mast - 5/16 (K) Slat wall to strap 5/32 () Slat wall anti-dislodgement 1/16 () llen wrenches (in inches) Wall Mounted Mast racket to Mast - 5/16 (K) Wall anti-dislodgement 1/16 () 1. Insert the mounting strap () into desired slatwall slot, with holes closer to top edge. ang slat wall bracket (), in desired slot aligning strap () holes with appropriate hole in bracket (). 2. Install and tighten (2) screws (). ang mast mount bracket () on slat wall bracket (), by engaging hanger strap () with top hook of hanger casting (). Seat mast mount bracket () down, fully onto hanger casting (). 3. Secure bracket () to casting (), with screw (). Insert mast () into bracket () positioning mast () with top of slope (J) facing the user. Seat mast () fully into bracket () and secure with screw (K). 1. Mark the locations for four mounting screws customer supplied () on the wall at the desired location, using the outer holes on the mounting plate () as a template, making sure the bracket is level. rill pilot holes in each location. 2. Pass the mounting screws through the outer holes on the mounting plate () and screw them into the wall. 3. ang arm mount bracket () on wall mount plate (), by engaging hanger strap () with top hook of hanger casting (). Seat mast mount bracket () down, fully onto hanger casting (). 4. Secure bracket () to casting (), with screw (). 5. Insert mast () into bracket (), positioning mast () with top of slope (J) facing the user. Seat mast () fully into bracket () and secure with screw (K). J J K ustomer supplied K 6
Step 2: ttach Monitor Plate (Movement Joint Included) to the Monitors or Television ttaching the Monitor to the rm (Movement Joint Including) to Monitor Plate Screwdriver or llen wrench 1. Remove monitor base and hardware from the monitor. Retain all hardware. 2. Place movement joint () against back of monitor or television, with Knoll logo toward top of monitor and attach the VS plate () using appropriate hardware. VS plate can accommodate 75 mm or 100 mm hole patterns. 3. ttach movement joint () to arm () by connecting them together, then inserting fast release pin (). Note: ach standard Sapper movement joint can hold up to 20 lbs. ach Sapper 50 movement joint can hold up to 30 lbs. Weight limit for mounting option specified may be less. Note: heck VS compliancy and hole pattern on monitor or television as Knoll monitor solutions are designed to work with VS compliant monitors only. The Knoll VS plate can accommodate 75mm or 100mm hole patterns. Knoll movement joints do not ship with screws and are designed to accept an M4 or M5 screw; length is dependent on the specific monitor or television and screw should be tested prior to installation to ensure correct length; Knoll is not responsible for use of incorrect screws. If monitor has recessed VS mounting surface, spacers () may be required between movement joint () and monitor. Spacers must be requested through Knoll ustomer Service. VS plate adaptor may be necessary for larger monitors and televisions and can be ordered separately in the sizes of 100 mm x 200mm (M5 screws), 200mm x 200mm (M6 screws), 300mm x 300mm (M8 screws) and 400mm x 400mm/400mm x 600mm (M8 screws). daptors ship with separate installation instructions and may require spacers. Knoll VS plate adaptors ship with screws to attach the adaptor to the Knoll VS plate but do not ship with screws to attach the adaptor to the monitor or television (see screw sizes listed above, nglish size equivalents may be needed instead); screw length is dependent on the specific monitor or television and screw should be tested prior to installation to ensure correct length, Knoll is not responsible for use of incorrect screws. ustomer supplied ustomer supplied 7
Step 3: ttach rms with Monitors to Mast llen wrenches (in inches) Top plate 5/32 (I) Mast anti-dislodgement 5/64 () Rotation braket 3/16 (K) 1. Remove the top plate () and top bushing () using a 5/32 llen wrench, on screws (I). 2. Slide arm and monitor assembly () onto each post (J) of the double-monitor bracket assembly (). Reconnect top plate () and top bushing (), ensuring that each arm assembly has full rotational movement. Reinstall screw (I). 3. Remove the mast top cap () and stop screw (). Rotate the adjustment knob () to the desired height. (Note: Knoll logo, on adjustment knob should be face up). 4. Place the double monitor arm assembly () onto the mast (). With the double monitor arm assembly in place, tighten screw (K), reinstall the stop screw () and top cap (). J I K 8
eatures: able Management and ast Release able Management ates and lip(s) ast Release To manage cables under the arm, open inboard gates () and (), by slightly moving gate up to overcome the snap detent. eed wires into the hollow under both arms. Snap both gates closed. Manage cables down mast () and install cables management clips (), by snapping clip () over cables and onto mast (). Please note there will be one clip for 8 masts and two clips for all masts 12 and longer. 1. ast release functionality allows rapid removal of monitor and movement joint. Remove the fast release pin () from the arm assembly (), disconnecting the movement joint (). 2. To reinstall, position movement joint on monitor arm and insert fast release pin (). When fully seated, pin should be flush. ates lips 9
eatures: riction djustment and nti-islodgement Tilt riction, Rotation riction and Independent Monitor Movement djustments nti-islodgement and Theft eterrence llen wrenches (in inches) Tilt friction 3/16 (Included on Monitor Plate) Rotation friction 3/16 () (Included on Monitor Plate) llen wrenches (in inches) nti-theft 1/16 () Tilt friction: To increase friction, insert llen wrench (included on each monitor plate) () into screw () and turn clockwise. To reduce tilt friction, turn screw () counterclockwise. djust in very small increments. Rotation friction: To increase friction, insert llen wrench () (included on each monitor plate) into screw () and turn clockwise. djust in very small increments. Independent monitor movement: To tighten and increase independent monitor movement, insert llen wrench (included on each monitor plate) () into screw () and turn clockwise. djust in very small increments. 1. Sapper monitor arms have anti-theft features. small set screw () resides inside the lower end of the fast release pin (). To activate anti-theft feature, use a 1/16 llen wrench and back set screw () partially out of fast release pin (). This prevents fast release function. 2. lso, the stop screw () at the top of the mast () prevents monitor arm from being removed. Tilt friction set screw Rotation friction 10 Independent Monitor Movement djustment