10/22/2010 Optical Infrared Communications.doc 1/17 Optical Infrared Communications Once information has been glued onto a carrier signal the information is used to modulate the carrier signal in some way the carrier signal can be propagated from one point (where the transmitter is located) to another point (where the receiver is located). This electromagnetic propagation can occur in one of two ways; either in a bounded channel (e.g., a transmission line or waveguide) or in an unbounded channel (e.g., in free-space). Electromagnetic energy at frequencies below 100 GHz (approximately) are coupled into (at the transmitter) and out of (at the receiver) free-space using an antenna. This creates a highly effective communications system, as electromagnetic propagation is very fast, 8 traveling at a velocity of almost 3 10 meters/second the speed of light! Moreover, electromagnetic energy oscillating at (carrier) frequencies of 2 GHz (approximately) propagate well through objects that we think of as opaque concrete, wood, drywall insulation, soil, etc.
10/22/2010 Optical Infrared Communications.doc 2/17 To signals propagating at a frequency less than 2 GHz a region loosely defined as the Radio Frequency (RF) region of the electromagnetic spectrum most solid objects appear to be transparent. In the RF frequency band, no one should throw stones, as everyone lives in a glass house! These two characteristics fast propagation and propagation through solid objects make RF signals a great carrier of important information. Q: Is electromagnetic communications limited only to the RF region? A: Absolutely not! Just above the RF region of the electromagnetic spectrum is the microwave region loosely defined as frequencies between 2 GHz and 20 GHz. Electromagnetic communication in the microwave region has some advantages over RF, but it is also hampered by the fact that solid objects don t look quite as transparent at microwave frequencies.
10/22/2010 Optical Infrared Communications.doc 3/17 As a result, microwave communication systems are typically line-of-site. For example, most satellite communications occurs in the microwave region. Q: What happens at frequencies beyond (above) the microwave region? A: Bad stuff happens, generally speaking. The most odious of this is the fact that the Earth s atmosphere does not even appear to be transparent at these higher frequencies. This is particularly true if the atmosphere is full of water vapor (i.e., clouds!). Q: So all electromagnetic communication occurs at frequencies in the RF or microwave region? A: Not all! Much communication also occurs using the visible and infrared regions. Way up at the high end of the electromagnetic spectrum is electromagnetic energy that oscillates at fantastically high frequencies and thus fantastically small wavelengths. We call this region the visible region for a very good reason propagating electromagnetic energy at these frequencies can actually be seen with the human eye!
10/22/2010 Optical Infrared Communications.doc 4/17 From: www.pol-us.net/asp_home/aspkids/em-spectrum.jpg Q: Wow! I can I see this electromagnetic wave? Where do I go? What do I do? A: You don t have to go anywhere or do anything. You are seeing this electromagnetic energy right now we gave propagating electromagnetic waves at these frequencies the name light. Visible light is simply a propagating electromagnetic wave in the visible region! Q: Why do you call it visible light? Is there such a thing as invisible light?
10/22/2010 Optical Infrared Communications.doc 5/17 A: Actually there is! Just a bit below (i.e., lower in frequency) the visible region is the infrared region. Infrared propagation is very similar to visible light, only we humans can t see it with our eyes. Q: But I don t understand. You said that visible and infrared energy is used for electromagnetic communication, but I know that visible light does not propagate through solid objects, nor does it propagate well through clouds. How is this region of the electromagnetic spectrum useful? A: Typically, the visible and infrared region of the electromagnetic spectrum is used for propagating a bounded wave. Specifically, visible and infrared energy is propagated in a waveguide. Waveguides are fundamentally different that transmission lines (e.g., a coaxial cable), but they both essentially constrain a propagating electromagnetic wave sort of an electromagnetic pipe! Microwave waveguide was developed during World War II at the MIT Radiation Lab the laboratory that developed modern radar.
10/22/2010 Optical Infrared Communications.doc 6/17 Waveguide in the electromagnetic propagation in the optical (i.e., visible and infrared) region was a more difficult technical challenge. The first successful waveguide at these frequencies was not constructed until the 1960 s. This waveguide has a more popular moniker of fiber optic or optical fiber. Fiber optic cable made possible the use of infrared and visible light for electromagnetic communications. Visible light encounters no clouds or buildings as it propagates through an optical fiber! Q: But I don t see why we would want to used visible light in bounded electromagnetic propagation. Can t we just propagate RF or microwave energy down a transmission line? A: We can and frequently do (e.g., cable TV!). However, the visible and infrared region of the electromagnetic spectrum has one gigantically important attribute that the RF and microwave regions do not bandwidth!
10/22/2010 Optical Infrared Communications.doc 7/17 The RF microwave regions of the electromagnetic spectrum spans a bandwidth of approximately 20 GHz. In contrast, the infrared and visible region of the electromagnetic spectrum has a bandwidth of more than 100,000 GHz 5000 times that of the entire RF/microwave region! Q: What s the big deal about bandwidth? A: Bandwidth determines the rate at which we can reliably send information the larger the bandwidth, the larger the data rate. Q: Do we really need such large bandwidths? I don t think I have that much to say! A: We didn t used to need that much bandwidth, but as you may have noticed, we humans now fling information back and forth in all directions with phenomenal alacrity. Texting, blogging, tweeting, talking, surfing, listening, viewing, downloading, searching, sharing, networking, and podcasting (LOL!) we communicate with a frequency and variety that was unfathomable just 30 years ago (whether we actually communicate any better is debatable). Without optical fiber, and the bandwidth it provides, modern life would be very different from what it actually is today!
10/22/2010 Optical Infrared Communications.doc 8/17 Q: What about communication via unbounded propagation of light? A: The problem of course is that electromagnetic energy does not propagate well in the infrared and visible light region. As you may have noticed, light does not penetrate stuff like walls, furniture, doors etc. For visible light and infrared, only windows are transparent! As a result, communication systems involving (mainly) infrared propagation can transfer information over a distance of 15 meters or less pretty much from one side of a room to the other side. Q: Transmit information across a room? Why would I want to do that? I don t need electronic communication to talk to someone in the same room! A: True, but most unbounded infrared communications systems are not designed to allow for humans to communicate with other humans, they are designed to allow for humans to communicate with other things. In other words, these communication systems allow humans to control devices within a room. Q: Can t we just walk across the room and control them?
10/22/2010 Optical Infrared Communications.doc 9/17 A: We can, but most humans now find this to be just too darn much work! Unbounded infrared communication systems are a prized possession of every couch potato and channel surfer it is these systems that allow TVs, cable boxes, stereos and DVD to be controlled remotely controlled remotely via a remote control! Q: You keep saying that these are infrared systems. Why don t we use light in the visible region for remote control systems? A: When you push a button on a remote, a light turns on at the end of the remote. If you shine this light on your TV, it will respond by changing the channel or increasing the volume. Q: Wait! I ve never noticed any light shining when I use my remotes, you must be confused! A: The reason that you ve never noticed this light is that this light is infrared it is not located in the visible region of the electromagnetic spectrum.
10/22/2010 Optical Infrared Communications.doc 10/17 This is why infrared (and not visible light) is used in remotes the light it produces is invisible to us humans! Q: So how do we modulate this infrared signal? How do we glue information onto this carrier? Do we use Amplitude Modulation (AM) or Frequency Modulation (FM)? A: It is exceedingly difficult and expensive to frequency modulate electromagnetic energy at infrared frequencies. In fact, it s pretty darn difficult to produce a coherent sine wave at these frequencies a laser is typically required! Thus, information is typically placed on the infrared signal via Amplitude Modulation (AM). Q: So, the resulting amplitude of the infrared signal is proportional to some information signal? A: Yes and no. It turns out that AM is no piece of cake either when applied to infrared. By far the easiest (and thus cheapest) way to Amplitude Modulate an infrared signal is simply to turn it on or turn it off! Thus, the infrared lights of most remotes are simply switched between and on and an off state!
10/22/2010 Optical Infrared Communications.doc 11/17 This typed of amplitude modulation is known as On-Off Keying (OOK) Q: But how can we use this to convey information? A: We can modify the rate at which the infrared signal is turned on and off! The rate (i.e., frequency) at which the infrared is switched is proportional to the information we wish to send. To be specific, the infrared signal of most remotes are typically switched on and off at a rate between 20 khz and 150 khz. This frequency is known as the chip rate ; 40 khz is a pretty standard chip rate for remote controls. Thus, the infrared signal is effectively Amplitude Modulated by a 40 khz square wave. When the square wave is in its high state, the infrared light is switched on. When the square wave is in its low sate (i.e., zero), the infrared light is switched off Q: But how does information get placed on this flashing light? A: There are various means, but typically information is placed on the signal by altering the chip rate in a manner that is proportional to the information signal.
10/22/2010 Optical Infrared Communications.doc 12/17 For example, say we wish to transmit a digital stream of data (i.e., ones and zeros ). This is typically what remotes do the binary word tells the TV what button has been pushed! We can convey this information by changing the chip rate from, say, 40 khz for a binary 0, to 45 khz for a binary 1. Of course, once we change the chip rate, the square wave must remain at that frequency for some significant amount of time (i.e., several cycles of the square wave), before it can change back to the other value. This time is known as the chip interval and is typically some integer number of square wave cycles. Thus, the data rate (in bits/second) of a remote is always less than the chip rate. For example, say we use a chip rate of 40 khz, and a chip interval of 33 cycles (i.e., 33 chips/bit). Since the period of a 40 khz is 25 micro seconds, the chip interval is 33 x 25 = 825 microseconds. Thus, a new bit of information is sent every 825 microseconds. The inverse of this value gives us the data rate 1/825 = 1200 bits/second.
10/22/2010 Optical Infrared Communications.doc 13/17 Q: Wow! That seems like an exceedingly slow data rate. Do these thing really work? A: A data rate of 1200 bits/second is plenty fast, considering all you are trying to do is tell the TV to go to channel 457! Q: Changing the chip rate frequency sounds a lot like Frequency Modulation (FM). Is that what we are doing? A: Absolutely! Changing the frequency of a signal between two (or more) fixed values is known as Frequency Shift Keying (FSK). FSK is a very popular FM technique for communicating digital information. The 40 khz square wave is also referred to as a sub-carrier. Communication via infrared light is thus accomplished in a two step process: 1. Information is used to Frequency Modulate a squarewave subcarrier. 2. This modulated square-wave sub-carrier is then used to Amplitude Modulate (OOK) an infrared light! Q: Must we use FSK to modulate the sub-carrier? Could we use (for example) an audio signal to Frequency Modulate the sub-carrier?
10/22/2010 Optical Infrared Communications.doc 14/17 A: Absolutely! In this case the subcarrier frequency would increase or decrease proportionally and continuously from its nominal value (e.g., 40 KHz), in response to an analog signal representing an audio pressure wave. We of course could use a VCO (with a square wave output) to provide this Frequency Modulation. So, let s put all the pieces together for an audio communications system using infrared light. First we have a transmitter: Low-Pass Filter va ( t ) Σ Audio Source Audio Gain V C LED Driver VCO vc ( t ) IR Light Emitting Diode
10/22/2010 Optical Infrared Communications.doc 15/17 1. The low-pass filter simply limits the signal bandwidth to audio frequencies; typically a value much less than 20 khz. 2. The audio gain stage sets the peak-to-peak audio at the correct value to generate the desired modulation bandwidth. 3. The DC bias value V C sets the VCO carrier frequency in this case the chip rate. 4. The summer combines the AC audio signal and the DC bias voltage. 5. The VCO of course creates the FM signal. In this case a Frequency Modulated square wave, centered the desired chip rate. 6. The LED Driver is essentially the switch circuit that turns the IR LED on and off (i.e., OOK) at the proper rate. 7. The IR LED is simply a Light Emitting Diode that emits light at some invisible IR frequency. Note that elements 2,3, and 4 can be combined or rearranged.
10/22/2010 Optical Infrared Communications.doc 16/17 Now for the receiver: IR Detector PLL Demodulator Detector Amp Audio Amp 1. The IR Detector is essentially an electronic eye that sees infrared energy. Its output put is proportional to the amplitude of IR light shining on it at any given time. Thus the output of this device will be proportional to the square wave that is driving the LED on the transmitter. This device is thus an IR Amplitude Demodulator! 2. The signal out of the detector, however, is very small. As a result, we require a very high gain amplifier to create the requisite square-wave signal into the PLL demodulator. There are IC amplifiers made for this very purpose! 3. The output of the Detector Amp becomes the reference signal for the PLL demodulator. The PLL locks onto this
10/22/2010 Optical Infrared Communications.doc 17/17 signal, and so the control voltage of the PLL VCO should be proportional to the audio signal at the transmitter. The signal is thus demodulated! 4. This demodulated audio is typically too small to be audible; it might require some significant audio amplification!