SHELTER ASSEMBLY MANUAL Model # 3085GL-17P Strongly ask to remove snow from the roof immediately. Do not leave any snow load on the roof. Keep both sides and two ends on the ground clear all the times. Do not allow snow to accumulate and pile up beside the building. The product has not been engineered or designed for use at a specific site and may not be suitable for local conditions. It is the responsibility of the purchaser to ensure that the installation and use of this structure is permitted by all authorized bodies. Low human occupancy is recommended at all times.
3085GL-17P Part List Parts Code Description Qty 1 Roof Bent Tube 17 2 Middle Bent Tube 30 2A Middle Bent Tube for front and back door 4 3 Lower Bent Tube 30 3A Lower Bent Tube for front and back door 4 4 Purlin 80 5L Base Plate for four corners on the left 2 5R Base Plate for four corners on the right 2 6 Base Plate for front and back door 4 7 Base Plate for inner sidewall 30 7A Ratchet 34 8 Lower Portal for door frame 4 9 Upper Portal for door frame 4 10 Upper Horizontal Connection Tube for door 4 11 Support Crossbeam for roof cover 17 11A Small Pulley 4 12 Lower Tension Tube for front and back door 4 13 Supporting tube for arch frame 4 13A Clip 8 14 Lower Tension Tube for roof cover (2 sets) 2 groups 15 Door Bracing Tube (2 sets) 2 groups 16 Stake Peg(Not included, available upon request.) 17 Bolt M10x80mm for No.4 85 18 Bolt M8x70mm for No.1,2,2A,3,3A 220 19 Bolt M10x30 mm for No.10&3A, No.9 &2A, No.1&11 46 20 Nylon Rope for ratchet 4 21 Plastic Plug for No.12 & 14 12 22 Roof Cover 1 23 Front and Back Door Cover 2 24 Knitting Rope for fixing cover 1 bundle 25 Nylon Band for No. 7A 34
SPECIFICATION W30'x L85' x H15' Length: 26m Width: 9.15m Height: 4.5m Door dimension: W3.65mxH3..3m (W12' x H11') IMPORTANT-----READ MANUAL FIRST Improper site preparation, Assembly and Maintenance may invalidate warranty and cause unnecessary and costly mistake. If you have any questions contact your local dealer. For User Friendly assembly we have identified each individual component with the part code as indicated in the parts list. Please refer to the part code numbers and drawing to ensure problem free assembly. It s necessary to tighten the roof fabric enough to avoid hammocks on the roof and also re-tighten once or twice again after a few months of use. This is important when assembly in cold weather (autumn and winter) because the fabric is stiff then and when we got the sun and warm weather afterwards it will make the fabric slack again and need to be re-tighten before next winter. It s the owners responsibility to take of snow immediately if not slide off by itself. READ ALL INSTRUCTIONS BEFORE ASSEMBLY 1. Keep work area clean. Cluttered areas invite injuries. Do not set up near snow drifts, in slippery places, in high winds, or wet location. 2. Keep children away. All children should be kept away from the work area. 3. Don t over reach. Keep proper footing and balance at all times. 4. Do not assemble in under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not assemble. 5. Be aware of possible windy conditions; fasten the bases in concrete if these conditions are likely to occur. Remove the cover during hurricane. 6. Be careful with power and heat sources. Do not keep heat sources near the tarpaulin. Do not expose to open flame. 7. Be aware of personal safety during assembly and use. Be careful not to pinch fingers with clips and tubes when assembling: when using makes sure there is adequate ventilation for exhaust and other dangerous fumes. - 2 -
EQUIPEMNT AND TOOLS FOR INSTALIATION 1. Measuring tape 2. String for alignment 3. Step ladder 4. Welder 5. Sledge hammer 6. Wrench 7. Scissors INSTALLATION PROCESS A BASE INSTALLATION Please refer to the diagram (Figure 1) to place the base plates. Figure 1 The measure if from center to center of the tubes. Referring to the above diagram and confirm the place of the base plates. ENSURE THAT THE FOUNDATIONS IS SQUARE. There are three holes on the Base Plates (No.5, 7) and two holes on the Base Plate (No.6), for Stake Peg (No.16). THUS ALL BASE PLATES ARE SECURED. Foundation Placement As Figure 2 shows each Base Plate is equipped with three pieces of Stake Peg (No.16) Figure 2 (Not included,available upon requests.) Note: The Stake Pegs apply for normal conditions, not suitable to the rock ground, frozen soil and concrete ground. - 3 -
(W30'x H85' x L15') FRAME SKETCH Figure 3-4 -
B FRAME INSTALLATION 1. As Figure 4 shown to find one Roof Bent Tube (No.1), two Middle Bent Tubes (No. 2), Lower Bent Tube (No. 3A) and assemble every group arch with Screw M8x70 (No.18). DO NOT install the screw on the top of the truss where the fabric will rest. Figure 4 Note: Middle Bent Tube and Lower Bent Tube for two end tubes (No.2A&3A) which are welded with steel plates for upper portal (No.9) and Upper horizontal connection tube for doors (No.10) are different from the middle arch. 2. Lift an assembled arch onto one base plate and force the other end of the arch onto the opposite base plate. IMPORTANT: THE ARCHED WILL BE WIDER THAN THE BASE PLATES 3. When finish installing the first two arches into the base plates, use Purlins (No.4) to connect them by Screw M10x80 (No.17). Then install the third arch into the third arch into the plate and connect the Purlins. In this turn, fix all other arches and other purlins. Then come to install the front panel and back panel. Find the relative components and assemble them. Figure 5
4. Connect the Support Crossbeam for roof cover (No.11), Supporting tube for arch frame(no.13), clip (No.13A) for frame as FRAME SKETCH (figure 3). C INSTRUCTION THE FRONT AND BACK COVER 1. Install the front and back door frame as Figure 6. Figure 6 2. Use Knitting Rope (No.24) on Front and Back cover to lace the grommets in the end to the tension tubes evenly. The end covers are tied to the frame (Roof, Middle & Lower Bent Tube) by Knitting Rope. They are also been secured to the end frame (door tube and side rail) by Knitting Rope. 3. Method of Fastening Front and Back Cover Insert the Door Bracing Tube (No.15) into the bottom of Front and Back door cover (No.23). Put the Nylon Rope for ratchet (No.20) into the door cover and the Small Pulley onto Support Crossbeam for roof cover like the Figure 7.Finally fix it onto the Base Plate (No.5L or 5R). 4. Tidy the Back Cover and Front Cover. Fasten the band inside the end of the roof cover, make the cover well fold to the frame and tie the end of the band to the Clips on Base Plates at four corners. - 6 -
D INSTRUCTION THE ROOF COVER Figure 7 NOTE: DO NOT install the cover onto the frame of your building in high wind conditions. A slight breeze is the most advantageous for cover installation. To take advantage of the breeze, pull the cover up over the arches with breeze blowing in the cover like a sail filled with air. 1. Assemble Tension Tube for Roof Cover (No.14) before installing the cover. 2. Roll out the roof cover on a ground sheet. Align the cover evenly to each end of the frame. Note: Be sure doing not pullover the end of the roof cover. 3. Pull the cover over the frame EVENLY, CAREFULLY AND SLOWLY. Insert the tension tubes (No.14) into the cover pipe pockets and loosely secure the Nylon Band (No.25) for ratchet in the Ratchet (No.7A). DO NOT TIGHTEN. Adjust the cover so that it is square and evenly centered on the frame. Put the lower tension tube inside. - 7 -
Figure 8 Note: The end flaps must overhang evenly at both ends. 4. With the end flaps flipped back and out of the way, use the supplied Knitting Rope (Part No. 24) to tighten the roof cover to the end arches. The rope should be cut as your requirements when using. The recommended procedure is to use separate pieces of rope and start by first lacing the cover from the bottom edges up to the top center. Secure the ropes at the top center and then apply tension as you lace down both sides. Fasten the rope at the bottom edge. Put the Plastic Plug (No.21) for part No. 12& 14 onto the end of tubes. Drive the Ratchet Tie Down forth and back and then roof cover is tightened. NOW THE INSTALLATION IS FINISHED. NOTE: DO NOT LEAVE THE ROOF COVER UNATTACHED UNDER ANY CIRCUMSTANCES until the final assembly and tightening has been completed. The process is quite easy. But some tightening adjustments will be necessary to produce a flat, tensioned roof cover. Please adjust the roof cover every month. - 8 -