Wiring for Damper ctuators and Control Valves July 011
Wiring for Damper ctuators and Control Valves eneral Wiring Instructions WRNIN: The wiring technician must be trained and experienced with electronic circuits. Disconnect power supply before attempting any wiring connections or changes. Make all connections in accordance with wiring diagrams and follow all applicable local and national codes. Provide disconnect and overload protection as required. Use copper, twisted pair, conductors only. If using electrical conduit, the attachment to the actuator must be made with fl exible conduit. lways read the controller manufacturer s installation literature carefully before making any connections. Follow all instructions in this literature. If you have any questions, contact the controller manufacturer and/or elimo. Transformer(s) elimo actuators require a VC Class transformer. The actuator enclosure cannot be opened in the field, there are no parts or components to be replaced or repaired. EMC Directive: 00/108/EC Software Class : Mode of Operation Type 1 Low Voltage Directive: 006/9/EC Example: F ctuators Supplied, 16 a. wire (refer to table on page ) 0 ft. (allowable wire length) actuators = 117 ft. maximum wire run Typical Transformer Sizing ctuator Series Voltage Required V Per ctuator EF, EFX 16 F, FX 10 F 10 NF, NFX 9 LF 7 TF M 7 M / R 6 NM 6 LM / LR CM 1. H. LH LU MQ 6 NMQ LMQ HQ LHQ K / KR 1 NK HK 0 CUTION: It is good practice to power electronic or digital controllers from a separate power transformer than that used for actuators or other end devices. The power supply design in our actuators and other end devices use half wave rectification. Some controllers use full wave rectification. When these two different types of power supplies are connected to the same power transformer and the DC commons are connected together, a short circuit is created across one of the diodes in the full wave power supply, damaging the controller. Only use a single power transformer to power the controller and actuator if you know the controller power supply uses half wave rectification. Multiple actuators, one transformer Multiple actuators may be powered from one transformer provided the following rules are followed: 1. The TOTL current draw of the actuators (V rating) is less than or equal to the rating of the transformer.. Polarity on the secondary of the transformer is strictly followed. This means that all No. 1 wires from all actuators are connected to the common leg on the transformer and all No. wires from all actuators are connected to the hotleg. Mixing wire No. 1 & on one leg of the transformer will result in erratic operation or failure of the actuator and/or controls. Multiple actuators, multiple transformers Multiple actuators positioned by the same control signal may be powered from multiple transformers provided the following rules are followed: 1. The transformers are properly sized.. ll No. 1 wires from all actuators are tied together and tied to the negative leg of the control signal. See wiring diagram. Wire type and wire installation tips For most installations, 18 or 16 a. cable works well with elimo actuators. Review job requirements and determine whether a plenum or appliance rated cable is appropriate. Use code-approved wire nuts, terminal strips or solderless connectors where wires are joined. It is good practice to run control wires unspliced from the actuator to the controller. If splices are unavoidable, make sure the splice can be reached for possible maintenance. Tape and/or wire-tie the splice to reduce the possibility of the splice being inadvertently pulled apart. Wire length for actuator installation Keep power wire runs below the lengths listed in the following tables. If more than one actuator is powered from the same wire run, divide the allowable wire length by the number of actuators to determine the maximum run to any single actuator. N0067-7/11 - Subject to change. elimo ircontrols (US), Inc. 800--908 US 866-80-7089 CND 0-791-896 LTIN MERIC / CRIEN
Wire Size vs. Length of Run for Damper ctuators and Control Valves N0067-7/11 - Subject to change. elimo ircontrols (US), Inc. wire gauge V EF F NF LF US TF US MQ NMQ K/ KR NKQ M/R M/R NM LM/LR CM H LH LU TR LMQ HQ LHQ 16 10 9 7 1 7 6 6 1. 6 1 18 MX Distance between ctuator and Supply (feet) 0 17 00 00 0 800 00 0 0 1100 70 18 1 0 0 0 110 10 7 7 0 110 7 0 0 100 1 VC 16 0 90 00 700 16 160 00 600 600 700 100 600 700 700 100 00 1 60 0 600 800 1100 7 60 800 9 9 00 1 0 900 1000 11 117 0 0 11 110 110 00 EF F..UP F NF..UP LF US TF US M M NM LM CM LU wire gauge V 1 8. 11 6. 7. 6 7 7. 6... MX Distance between ctuator and Supply (feet) 0 17 10 17 0 0 00 18 110 6 1 7 7 00 0 600 70 16 16 1 7 00 7 00 0 00 700 1000 11 110 VC 1 7 60 900 800 900 800 700 800 11 110 117 1 0 100 89 110 11 110 11 11 11 EF F..UP F US NF..UP LF US TF US M M NM LM CM LU wire gauge V 9 18 11 9. 7 6 7 7. 6... MX Distance between ctuator and Supply (feet) 0 17 10 17 0 00 18 80 10 1 0 7 00 0 600 70 16 1 00 0 00 7 00 0 00 700 1000 11 0 VC 1 00 00 0 800 900 800 700 800 11 100 117 1 10 7 89 900 11 110 11 11 11 *elimo actuators and auxiliary switches are designed as a IEC protection class II, double insulated, and do not require an independent ground wire to earth, unless otherwise indicated in this document 800--908 US 866-80-7089 CND 0-791-896 LTIN MERIC / CRIEN
Wire Size vs. Length of Run for SY Series ctuators SY1 SY SY SY SY mps mps mps mps mps wire gauge 1.8 6 6. MX Distance between ctuator and Supply (feet) 18 9 16 1 87 87 0 1 10 10 70 6 1 7 1 1 107 99 10 606 6 6 18 168 8 90 71 0 VC SY1 SY SY SY SY SY6 SY7 SY8 SY9 SY10 SY11 SY1 mps mps mps mps mps mps mps mps mps mps mps mps wire gauge 0. 1 1 1. 1. 1.8.. MX Distance between ctuator and Supply (feet) 18 11 78 78 8 0 1 7 189 7 189 189 16 81 1190 1190 916 79 661 7 98 7 98 97 98 1 86 19 19 179 18 1068 601 81 601 81 61 81 1 88 91 91 6 1961 16 919 7 919 7 980 7 10 10000 000 000 86 778 16 10 16 10 1667 10 8 19 76 76 71 97 16 1866 1866 88 1866 110 VC SY1 SY SY SY SY SY6 SY7 SY8 SY9 SY10 SY11 SY1 mps mps mps mps mps mps mps mps mps mps mps mps wire gauge 0. 0. 0. 0.6 0.7 0.8 1.6 1.6 1.6. MX Distance between ctuator and Supply (feet) 18 01 00 00 16 189 97 78 97 78 97 689 16 797 76 76 968 01 976 188 1190 188 1190 188 108 1 181 769 769 610 9 808 0 19 0 19 0 178 1 19608 1176 1176 980 80 7 676 91 676 91 676 67 10 0000 0000 16667 186 100 60 000 60 000 60 8 971 981 981 876 1 1867 98 76 98 76 98 678 0 VC The NEC mandates that VC over 100 V power requires CLSS 1 wiring conduit. Local codes may vary. Do NOT mix CLSS 1 & CLSS circuits in the same conduit. enerally, VC actuators over 100 V should be changed to 10 VC models. N0067-7/11 - Subject to change. elimo ircontrols (US), Inc. 800--908 US 866-80-7089 CND 0-791-896 LTIN MERIC / CRIEN
W6_11 Wiring for Damper ctuators and Control Valves On/Off, Spring Return, Electronic Fail-Safe, V ctuators: EF(-S) EFX(-S) F(-S) US NF(-S) NFX(-S) LF(-S) US TF(-S) US K- KX- NKQ-1 NKQX-1 CUTION ctuators may be connected in parallel. Power consumption and input impedance must be observed. WRNIN Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. 1 ctuators may also be powered by VDC. On/Off INSTLLTION NOTES Provide overload protection and disconnect as required. ctuators with plenum rated cable do not have numbers on wires; use color codes instead. ctuators with appliance cables are numbered. PPLICTION NOTES Meets culus requirements without the need of an electrical ground connection. On/Off VC Transformer 1 VC Transformer Red () + Hot a open a closed a Red () + Wht () + N0067-7/11 - Subject to change. elimo ircontrols (US), Inc. The indication of direction is valid for switch position 1. On/Off VC Transformer a 1 0 1 NKQ Red () + Hot Wht () + Y 1 input K Refer to page 6 for auxiliary switch (-S models) wiring. 800--908 US 866-80-7089 CND 0-791-896 LTIN MERIC / CRIEN
W1 11 Wiring for Damper ctuators and Control Valves On/Off, Spring Return, 10, 0V and UP ctuators: EF10(-S) EFX10(-S) FUP(-S) FXUP(-S) F10(-S) US/F0(-S) US NFUP(-S) NFXUP(-S) LF10(-S) US/LF0(-S) US TF10(-S) US CUTION ctuators may be connected in parallel. Power consumption and input impedance must be observed. WRNIN Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. 1 19 0 UP INSTLLTION NOTES TF10(-S) US can be supplied with both 10 VC and 0 VC. UP models and TF10(-S) US uses L instead of H on # wire. ll 10 VC, 0 VC and UP actuators use appliance rated cables. Universal Power Supply (UP) models can be supplied with VC up to 0 VC. PPLICTION NOTES Meets culus requirements without the need of an electrical ground connection. On/Off 10 VC 0 VC Wht N lk H 1 UP 0 19 Wht (1) Neutral lk () Hot N0067-7/11 - Subject to change. elimo ircontrols (US), Inc. Refer to page 6 for auxiliary switch (-S models) wiring. 6 800--908 US 866-80-7089 CND 0-791-896 LTIN MERIC / CRIEN
W_11 Wiring for Damper ctuators and Control Valves Floating Point, Spring Return, V ctuators: LF-(-S) US TF-(-S) US LFC-...US CUTION ctuators may be connected in parallel. Power consumption and input impedance must be observed. WRNIN Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Floating Point INSTLLTION NOTES ctuators may also be powered by VDC. ctuators with plenum rated cable do not have numbers on wires; use color codes instead. ctuators with appliance cables are numbered. ctuators Hot wire must be connected to the control board 6 common. For triac sink the Common connection from the actuator 11 must be connected to the Hot connection of the controller. The actuator must be connected to the control board common. PPLICTION NOTES Meets culus requirements without the need of an electrical ground connection. ctuator Wire Number Color TF- US Org TF--S US Org LF- US rn LF--S US Wht Triac Source VC Transformer N0067-7/11 - Subject to change. elimo ircontrols (US), Inc. Triac Sink The indication of direction is valid for switch position CW. Hot Controller a b VC Transformer Com Red () + Hot Wht () + + CW CCW LF-(-S) US LFC--R US LFC--S US TF-(-S) US Red () + Hot Wht () + + CW 11 CCW LF-(-S) US TF-(-S) US The indication of direction is valid for switch position CW. 6 Hot Controller VC Transformer Com Triac Sink with Separate Transformer VC Transformer Hot Com VC Transformer Red () + Hot Wht () + + CW CCW LF-(-S) US TF-(-S) US The indication of direction is valid for switch position CW. Red () + Hot 6 Wht () + + CW CCW LF-(-S) US TF-(-S) US Refer to page 6 for auxiliary switch (-S models) wiring. Controller The indication of direction is valid for switch position CW. 800--908 US 866-80-7089 CND 0-791-896 LTIN MERIC / CRIEN 7
W_11 Wiring for Damper ctuators and Control Valves On/Off and Floating Point, Non-Spring Return, V ctuators: LM-(-S) (-P) (-P10) (-T) M-(-S) LMX-(-T) MX-(-T) LR-(-S) RX- TR-(-T) US NM- M- NMX-(-T) MX- R-(-S) LRX- CM- R-- R-- R--7 M--X1 LRC-(-S) CUTION ctuators may be connected in parallel. Power consumption and input impedance must be observed. WRNIN Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. INSTLLTION NOTES ctuators may also be powered by VDC. ctuators with plenum rated cable do not have numbers on wires; use color codes instead. ctuators with appliance cables are numbered. The TR--T US actuators are provided with 16 a numbered screw terminal strip instead of cable. 17 TR- US actuators cannot be wired in parallel. PPLICTION NOTES Meets culus requirements without the need of an electrical ground connection. On/Off Floating Point VC Transformer VC Transformer a open a closed The indication of direction is valid for switch position 1. On/Off SPDT Switch VC Transformer a Red () + Wht () + 1 0 LM(X)-... NM(X)-... M(X)-... M(X)-... CM-... LR(X)-... R(X)-... Floating Point The indication of direction is valid for switch position 1. Red () + Wht () + 16 17 VC Transformer 16 17 1 0 LM(X)-... NM(X)-... M(X)-... M(X)-... CM-... LR(X)-... R(X)-... N0067-7/11 - Subject to change. elimo ircontrols (US), Inc. lk 1 Common Red + lk 1 Common Red + Wht + Wht + Note: TR- (-T) US cannot be wired in parallel with any actuator. TR- (-T) US Note: TR- (-T) US cannot be wired in parallel with any actuator. TR- (-T) US Refer to page 6 for auxiliary switch (-S models) and -P, -P10 potentiometer wiring. 8 800--908 US 866-80-7089 CND 0-791-896 LTIN MERIC / CRIEN
W61_11 Wiring for Damper ctuators and Control Valves Floating Point, Electronic Fail-Safe, V ctuators: K- CUTION ctuators may be connected in parallel. Power consumption and input impedance must be observed. WRNIN Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. 1 Provide overload protection and disconnect as required. 8 INSTLLTION NOTES ctuators may also be powered by VDC. Control signal may be pulsed from either the Hot (source) or the Common (sink) VC line. Contact closures & also can be triacs. & should both be closed for triac source and open for triac sink. 9 For triac sink the common connection from the actuator must be connected to the hot connection of the controller. PPLICTION NOTES Meets culus requirements without the need of an electrical ground connection. Floating Point N0067-7/11 - Subject to change. elimo ircontrols (US), Inc. K- 800--908 US 866-80-7089 CND 0-791-896 LTIN MERIC / CRIEN 9
W6_11 Wiring for Damper ctuators and Control Valves On/Off and Floating Point, Non-Spring Return, 100 to 0V ctuators: LMX10- MX10- LRX10- CM10- NMX10- MX10- RX10- CUTION ctuators may be connected in parallel. Power consumption and input impedance must be observed. WRNIN Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. 1 19 INSTLLTION NOTES LM(X), NM(X), M(X), M(X), LR(X), and R(X) can be supplied with either 10 VC or 0 VC. ll 10VC and 0VC actuators use appliance rated cables. ctuators with appliance cables are numbered. PPLICTION NOTES Meets culus requirements without the need of an electrical ground connection. On/Off Floating Point N L1 H L 100 to 0 VC a open a closed 1 The indication of direction is valid for switch position 1. a 19 100 to 0 VC 1 19 lu (1) Common N L1 lk () + H L Red () + Wht () + 1 0 The indication of direction is valid for switch position 1. Wht () + 1 0 N0067-7/11 - Subject to change. elimo ircontrols (US), Inc. Refer to page 6 for auxiliary switch (-S models) wiring. 10 800--908 US 866-80-7089 CND 0-791-896 LTIN MERIC / CRIEN
W 11 Wiring for Damper ctuators and Control Valves Proportional, Spring Return, V ctuators: EF-SR(-S) EFX-SR(-S) F-SR(-S) FX-SR(-S) F-SR US F-SR US NF-SR(-S) NFX-SR(-S) LF-SR(-S) US TF-SR(-S) US CUTION Up to four actuators may be connected in parallel if not mechanically linked. Power consumption and input impedance must be observed. ctuators may also be powered by VDC. 6 INSTLLTION NOTES ctuators with plenum rated cable do not have numbers on wires; use color codes instead. ctuators with appliance cables are numbered. Only connect common to neg. ( ) leg of control circuits. WRNIN Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. 7 8 PPLICTION NOTES Meets culus requirements without the need of an electrical ground connection. 00 Ω resistor converts the to 0 m control signal to to 10 VDC. The F-SR US and TF-SR(-S) US are supplied without position feedback. N0067-7/11 - Subject to change. elimo ircontrols (US), Inc. VC Transformer ( ) Control Signal (+) VDC/m to 10 VDC ( ) Feedback Signal (+) 6 Ω 00 Ω Red () + Hot Wht () Y Input, to 10 CW CCW 7 () U Output, to 10V ctuator Wire Number Color EF-SR(-S) Org EFX-SR(-S) Org F-SR(-S) Org FX-SR(-S) Org F-SR US Wht NF-SR(-S) Org NFX-SR(-S) Org LF-SR US rn LF-SR-S US Wht EF-SR(-S) VC Transformer 7 EFX-SR(-S) F-SR(-S) FX-SR(-S) F-SR US Red () + Hot NF-SR(-S) NFX-SR(-S) Ω LF-SR(-S) US ( ) 00 Ω Control Signal (+) Wht () Y Input, VDC/m to 10V 6 8 F-SR US TF-SR(-S) US Refer to page 6 for auxiliary switch (-S models) wiring. 800--908 US 866-80-7089 CND 0-791-896 LTIN MERIC / CRIEN 11
W_11 Wiring for Damper ctuators and Control Valves Proportional, Non-Spring Return, Electronic Fail-Safe, V ctuators: LM-SR (-T) NM-SR LMX-SR (-T) NMX-SR (-T) LR-SR TR-SR (-T) US M-SR M-SR MX-SR (-T) MX-SR R-SR LRX-SR RX-SR CM-SR-L CM-SR-R K-SR KX-SR NKQ-SR NKQX-SR CUTION Up to four actuators may be connected in parallel if not mechanically linked. Power consumption and input impedance must be observed. WRNIN Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. ctuators may also be powered by VDC. 6 7 INSTLLTION NOTES ctuators with plenum rated cable do not have numbers on wires; use color codes instead. ctuators with appliance cables are numbered. Only connect common to neg. ( ) leg of control circuits. Terminal models (-T) have no-feedback. PPLICTION NOTES Meets culus requirements without the need of an electrical ground connection. 00 Ω resistor converts the to 0 m control signal to to 10 VDC. VC Transformer VC Transformer Control Signal VDC/m ( ) (+) 6 Ω 00 Ω 7 Red () + Hot Wht () Y Input to 10V TR-SR (-T) US ( ) Control Signal (+) VDC/m to 10 VDC ( ) Feedback Signal (+) 6 Ω 00 Ω 7 Red () + Hot Wht () Y Input, to 10V Org () U Output, to 10V 1 0 LM(X)-SR... NM(X)-SR... M(X)-SR... M(X)-SR... LR(X)-SR... R(X)-SR... LH(X)-SR... H(X)-SR... N0067-7/11 - Subject to change. elimo ircontrols (US), Inc. LU(X)-SR CM-SR... K... NK... 1 800--908 US 866-80-7089 CND 0-791-896 LTIN MERIC / CRIEN
W6_11 Wiring for Damper ctuators and Control Valves Proportional, Non-Spring Return, 100 to 0V ctuators: LMX10-SR MX10-SR RX10-SR NMX10-SR LRX10-SR CUTION ctuators may be connected in parallel. Power consumption and input impedance must be observed. 1 LM(X), NM(X), M(X), M(X), LR(X), and R(X) can be supplied with either 10 VC or 0 VC. 6 INSTLLTION NOTES Only connect common to neg. ( ) leg of control circuits. 19 ll 10 VC and 0 VC actuators use appliance rated cables. ctuators with appliance cables are numbered. WRNIN Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. 7 PPLICTION NOTES Meets culus requirements without the need of an electrical ground connection. 00 Ω resistor converts the to 0 m control signal to to 10 VDC. 100 to 0 VC 1 19 N0067-7/11 - Subject to change. elimo ircontrols (US), Inc. N L1 H L Wht (1) Neutral lk () Hot + 6 7 Red () Hot + Control Signal VDC/m ( ) (+) Wht () Y Input, to 10V to 10 VDC ( ) Feedback Signal (+) Org () U Output, to 10V 1 0 Cable Cable 1 800--908 US 866-80-7089 CND 0-791-896 LTIN MERIC / CRIEN 1
W 11 Wiring for Damper ctuators and Control Valves Phasecut Control Signal, Spring Return and Non-Spring Return, V ctuators: F-PC US LMX-PC MX-PC LRX-PC NMX-PC MX-PC RX-PC CUTION ctuators may be connected in parallel. Power consumption and input impedance must be observed. WRNIN Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. ctuators may also be powered by VDC. INSTLLTION NOTES ctuators with plenum rated cable do not have numbers on wires; use color codes instead. ctuators with appliance cables are numbered. PPLICTION NOTES Meets culus requirements without the need of an electrical ground connection. VC Transformer ( ) Control Signal (+) 0 to 10 V Phasecut Red () Hot + Wht *() Y Input, 0 to 10V phasecut Org () U Output, to 10V * White color wire for F-PC US, Pink color for all others. White color wire for F-PC US, Orange color for all others. PC N0067-7/11 - Subject to change. elimo ircontrols (US), Inc. 1 800--908 US 866-80-7089 CND 0-791-896 LTIN MERIC / CRIEN
W60_11 Wiring for Damper ctuators and Control Valves Proportional, Spring Return, V, kω or 10 kω Control Input ctuators: LF-ECON-R0 US LF-ECON-R10 US F-ECON-R0 US CUTION ctuators may be connected in parallel. Power consumption and input impedance must be observed. WRNIN Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. 6 7 8 9 0 INSTLLTION NOTES ctuators with plenum rated cable do not have numbers on wires; use color codes instead. ctuators with appliance cables are numbered. Min-position is adjustable from 0 to 100% with a potentiometer on the actuator cover. relay or switch can spring return the actuator when the RTU fan de-energizes, or if low ambient temperature is sensed. standard relay can be used to close the sensor circuit to engage economizer mode, e.g. outside air changeover device like a dry bulb or enthalpy limit switch. Honeywell logic module W79 and enthalpy sensor C700 also provide terminals for this switching. remote CO sensor or DDC controller can change the standard relay opening or closing the sensor circuit. This device can be a relay or a dry bulb/enthalpy limit switch. Override control for Y only accepts 0 to 10 VDC override control. N0067-7/11 - Subject to change. elimo ircontrols (US), Inc. Override Control Wire Input Signal F-ECON LF-ECON position pplication Y1 VC Drive closed (0%) Morning warm-up cycle Y1 Common Drive open (100%) Smoke Purge Y1 Open wire Drive to min. position Mechanical cooling in use, RTU thermostat calls for heat. Y 0 VDC to 10 VDC Min. position of 0% to 100% Override potentiometer via a remote C0 sensor/controller or DDC controller. Standard Economizer Mode Wiring VC Transformer kω NTC* M thermistor setpoint F 7 9 8 ( ) Control Signal (+) 0 to 10 VDC 0 Red () + Hot Wht () Y 1 Org () Y Min-pos, 0 to 10 V rn () U Output, to 10V Default CW CCW 1 6 0..8..6 MIN F-ECON-R0 US LF-ECON-R0 US LF-ECON-R10 US W0 Override VC Transformer Override Closed (0%) Override Open (100%) 7 ( ) Control Signal (+) 0 to 10 VDC 9 0 Red () + Hot Wht () Y 1 Org () Y Min-pos, 0 to 10V rn () U Output, to 10V Default CW CCW 1 6 0..8..6 MIN F-ECON-R0 US LF-ECON-R0 US LF-ECON-R10 US W0 *10 kω NTC thermistor for -R10 types. 800--908 US 866-80-7089 CND 0-791-896 LTIN MERIC / CRIEN 1
W60_11 Wiring for Damper ctuators and Control Valves Proportional, Spring Return, V, to 10 VDC (or to 0 m) Control Signal or Three-Position On/Off Control ctuators: LF-SR-E US CUTION ctuators may be connected in parallel. Power consumption and input impedance must be observed. WRNIN Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. 7 6 1 INSTLLTION NOTES ctuators may also be powered by VDC. ctuators with plenum rated cable do not have numbers on wires; use color codes instead. ctuators with appliance cables are numbered. 00 Ω resister converts the to 0 m control signal to to 10 VDC. Min-position is adjustable from 0 to 100% with a potentiometer on the actuator cover. For three-position control set direction of rotation to CW (default). Switch, actuator spring returns when open (e.g., fan interlock). Three-Position Control with a SPDT Switch or Two Contact Closures (e.g. fan, cooling Y) 1 VC Transformer W176 PPLICTION NOTES VC Red () x + Min-position Meets culus requirements without the need of an electrical ground connection. Wht () D Y Full Open 1 Provide overload protection and disconnect as required. rn () U Output, to 10V Three-Position Control Signals Switch Wire -Red (x) Wire -White (D) Position Open** ny ny Closed (via spring) Closed VC Open Min-position* Closed Open VC Full Open* Closed VC VC Full Open* * Desired position achieved by driving actuator with motor. ** n example would be to interlock the actuator power supply with the fan motor starter. to 10 VDC Control of LF-SR-E US 1 VC Transformer Ω Red () + Hot W179 Min-Position with Full Open Override (with a single contact closure) 1 VC Transformer VC 1 Default CW lk (1) CCW LF-SR-E US 6 Common Red () x + Min-position Wht () D Y Full Open 1 0 MIN.8..6. W176 N0067-7/11 - Subject to change. elimo ircontrols (US), Inc. Control Signal ( ) (+) to 10 VDC 7 Wht () Y Input, to 10V rn () U Output, to 10V Default CW CCW 1.8.6 1 rn () Default CW CCW U Output, to 10V 6 1 0.8..6. 6 0.. LF-SR-E US MIN LF-SR-E US MIN 16 800--908 US 866-80-7089 CND 0-791-896 LTIN MERIC / CRIEN
W606_11 Wiring for Control Valves On/Off and Floating Point, Spring and Non-Spring Return, V ctuators: NV- US NVD- US NVFD (-E) US CUTION ctuators may be connected in parallel. Power consumption and input impedance must be observed. Floating Point and On/Off Control (diagram shown with default position of S1.: Off) VC Transformer WRNIN Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. PPLICTION NOTES Meets culus requirements without the need of an electrical ground connection. On/Off Control-using actuator to drive open/close, spring upon power loss. (diagram shown with default position of S.: -way Off, -way On) lk (1) Common Wht () + extending VC Transformer lk (1) Common Wht () + retracting NV- US NVD- US = actuator plunger extending Red () + Hot Wht () Y 1 Input NVFD US NVFD-E US = actuator plunger retracting N0067-7/11 - Subject to change. elimo ircontrols (US), Inc. On/Off Control (diagram shown with default position of S1.: Off) VC Transformer lk (1) Common Wht () + extending Wht () + retracting NV- US NVD- US On/Off Control-using actuator to drive one direction and spring the opposite direction. NOTE: bridge must be made inside the NVF between terminals and (diagram shown with default position of S.: -way Off, -way On) VC Transformer lk (1) Common Wht () + Hot Wht () Y 1 Input Triac Source Floating Point Triac Sink Floating Point Hot Controller Hot Controller VC Transformer (C only) Com VC Transformer (C only) Com lk (1) Common Wht () + Hot Wht () Y 1 Input NV- US NVD- US lk (1) Common Wht () + Hot Wht () Y 1 Input NV- US NVD- US NVFD US NVFD-E US SPRIN RETURN CTUTORS MODEL DESINTION retracting plunger (spring up) NVFD US NVFD-MFT US NVF-MFT US extending plunger (spring down) NVFD-E US NVFD-MFT-E US NVF-MFT-E US 800--908 US 866-80-7089 CND 0-791-896 LTIN MERIC / CRIEN 17
W607_11 Wiring for Control Valves MFT, Spring and Non-Spring Return, V ctuators: NVF-MFT (-E) US NVFD-MFT (-E) US NV-MFT US NVD-MFT US CUTION ctuators may be connected in parallel. Power consumption and input impedance must be observed. WRNIN Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. 10 8 1 INSTLLTION NOTES For triac sink the Common connection from the actuator must be connected to the Hot connection of the controller. Position feedback cannot be used with a triac sink controller. The actuator internal common reference is not compatible. PPLICTION NOTES Meets culus requirements without the need of an electrical ground connection. Control signal may be pulsed from either the Hot (Source) or Common (Sink) VC line. IN00 or IN007 diode. (IN007 supplied, elimo part number 01) Triac Source Floating Point Floating Point Control. (diagram shown with default position of S.: -way Off, -way On.) 1 Requires diode MFT Typical to 10 VDC or to 0 m Wiring (diagram shown with default position of S.: -way Off, -way On) VC Transformer to 10 VDC Feedback Signal VC Transformer to 10 VDC ( ) Feedback Signal (+) VC Transformer ( ) Control Signal VDC/m (+) to 10 VDC ( ) (+) Feedback Signal Ω 00 Ω lk (1) Common Red () + Hot Wht () Y 1 Input Wht () U Output, to 10V NVF-MFT US NVF-MFT-E US NVFD-MFT US NVFD-MFT-E US NV-MFT US NVD-MFT US Pulse Width Modulation Control Wiring (diagram shown with default position of S.: -way Off, -way On) 8 1 lk (1) Common Red () + Hot Wht () Y Input Wht () U Output NVF-MFT US NVF-MFT-E US NVFD-MFT US NVFD-MFT-E US NV-MFT US NVD-MFT US Red () + Hot Wht () Y1 Input, to 10V Wht () U Output, to 10V NVF-MFT US NVF-MFT-E US NVFD-MFT US NVFD-MFT-E US NV-MFT US NVD-MFT US Triac Sink Floating Point Hot Controller VC Transformer (C only) COM 1 Position Feedback SPRIN RETURN CTUTORS MODEL DESINTION retracting plunger (spring up) NVFD US NVFD-MFT US NVF-MFT US Hot Controller 1 Red () + Hot Wht () Y1 Input, to 10V Wht () U Output, to 10V CCW VC Transformer (C only) COM CW NVF-MFT US NVF-MFT-E US NVFD-MFT US NVFD-MFT-E US NV-MFT US NVD-MFT US Direction of rotation switch CCW CCW CW CW 1 1 10 1 Red () + Hot Wht () Y1 Input, to 10V Wht () U Output, to 10V NVF-MFT US NVF-MFT-E US NVFD-MFT US NVFD-MFT-E US NV-MFT US NVD-MFT US extending plunger (spring down) NVFD-E US NVFD-MFT-E US NVF-MFT-E US N0067-7/11 - Subject to change. elimo ircontrols (US), Inc. 18 800--908 US 866-80-7089 CND 0-791-896 LTIN MERIC / CRIEN
W8 11 Wiring for Damper ctuators and Control Valves MFT, Spring Return, V ctuators: TF-MFT US LF-MFT(-S) US CUTION Floating Point ctuators may be connected in parallel if not mechanically mounted to the same shaft. Power consumption and input impedance must be observed. WRNIN Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. VC Transformer 10 INSTLLTION NOTES ctuators may also be powered by VDC. ctuators with plenum rated cable do not have numbers on wires; use color codes instead. ctuators with appliance cables are numbered. Control signal may be pulsed from either the Hot (Source) 8 or Common (Sink) VC line. For triac sink the Common connection from the actuator must 10 be connected to the Hot connection of the controller. Position feedback cannot be used with a Triac sink controller. The actuator internal common reference is not compatible. PPLICTION NOTES Meets culus requirements without the need of an electrical ground connection. 7 00 Ω resistor converts the to 0 m control signal to to 10 VDC. 9 Contact closures & also can be triacs. & should both be closed for triac source and open for triac sink. 1 IN00 or IN007 diode. (IN007 supplied, elimo part number 01). N0067-7/11 - Subject to change. elimo ircontrols (US), Inc. PWM 8 ( ) to 10 VDC Feedback Signal (+) 9 1 VC Transformer (C only) ( ) Position (+) Feedback VDC ctuator Wire Number Color TF-MFT US Org LF-MFT US Wht 8 lk (1) Common Red () + Hot Wht () Y1 Input CCW CW () U Output to 10V Direction of rotation switch CCW CCW CW CW Red () + Hot Wht () Y Input () U Output CCW CW Two Position Override Control to min, mid, max, Positions ( ) Control Signal -10 VDC or to 0 m (+) 7 VC/DC Transformer ( ) Position Feedback VDC (+) VC Transformer (C only) Ω 00 Ω 1/ watt C a Min* Mid* lk (1) Red () Red () + Hot Wht () Y 1 Input, to 10V Functions 0% 0% Common Hot Wht () Y Input () U Output CCW CW C Max* 100% Normal** Control mode acc. to Y * Default selectable 0-100%. See Configuration Data Sheet. ** Customizable. See Configuration Data Sheet. Refer to page 6 for auxiliary switch (-S models) wiring. 800--908 US 866-80-7089 CND 0-791-896 LTIN MERIC / CRIEN 19
W00 11 Wiring for Damper ctuators and Control Valves MFT, Spring Return, Non-Spring Return, Electronic Fail-Safe, V ctuators: EF-MFT(-S) EFX-MFT(-S) F-MFT(-S) FX-MFT(-S) NF-MFT(-S) NFX-MFT(-S) LMX LRX NMX MX RX KX NKQ RX-MFT- R-MFT- RX-MFT- MX-MFT-X1 R-MFT-S R-MFT- R-MFT-7 CUTION VDC/-0 m ctuators may be connected in parallel if not mechanically mounted to the same shaft. Power consumption and input impedance must be observed. WRNIN Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. VC Transformer ctuators may also be powered by VDC. ctuators with plenum rated cable do not have numbers on wires; use color codes instead. ctuators with appliance cables are numbered. Control signal may be pulsed from either the Hot (Source) 8 or Common (Sink) VC line. For triac sink the Common connection from the actuator 10 must be connected to the Hot connection of the controller. Position feedback cannot be used with a triac sink controller. The actuator internal common reference is not compatible. 7 9 INSTLLTION NOTES PPLICTION NOTES Meets culus requirements without the need of an electrical ground connection. 00 Ω resistor converts the to 0 m control signal to to 10 VDC. Contact closures & also can be triacs. & should both be closed for triac source and open for triac sink. ( ) Control Signal (+) to 0 m or to 10 VDC Ω 7 00 Ω 1/ watt Red () + Hot Wht () Y 1 Input, to 10V Pnk () Y Input rn () U Output, to 10V Two Position VC/DC Transformer Red () Hot Floating Point (except NKQ) ( ) to 10 VDC Feedback Signal (+) VC Transformer Direction of rotation switch CCW CCW CW CW CCW CW Triac Source and Sink Diagrams (See page 1) PWM (except NKQ) 8 9 10 Red () Hot + Wht () Y1 Input Pnk () Y Input Org () U Output to 10V Override Control to min, mid, max, Positions VC Transformer (C Only) ( ) Position Feedback VDC (+) ( ) Control Signal -10 VDC or to 0 m (+) 7 Ω 00 Ω 1/ watt C a Wht () Y Input Pnk () Y Input Org () U Output Red () + Hot Wht () Y 1 Input, to 10V Pnk () Y Input Org () N0067-7/11 - Subject to change. elimo ircontrols (US), Inc. VC Transformer (C only) 8 Position ( ) Feedback VDC (+) Red () + Hot Wht () Y Input Pnk () Y Input Org () U Output Min* Mid* Max* Normal** Functions 0% 0% 100% Control mode acc. to Y a b c * Default selectable 0-100%. See Configuration Data Sheet. ** Customizable. See Configuration Data Sheet. 0 800--908 US 866-80-7089 CND 0-791-896 LTIN MERIC / CRIEN
W0_11 Wiring for Damper ctuators and Control Valves MFT, Non-Spring Return, V ctuators: LMX LRX NMX MX RX RX-MFT- R-MFT- MX-MFT MX-MFT-X1 RX-MFT- RX-MFT-7 R-MFT- R-MFT-7 CUTION ctuators may be connected in parallel if not mechanically mounted to the same shaft. Power consumption and input impedance must be observed. 6 11 INSTLLTION NOTES ctuators with plenum rated cable do not have numbers on wires; use color codes instead. ctuators with appliance cables are numbered. Only connect common neg (-) leg of control circuits. For triac sink with common connection from the actuator must be connected to the hot connection of the controller. The actuator must be connected to the control board common. WRNIN Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. PPLICTION NOTES Meets culus requirements without the need of an electrical ground connection. Triac Sink Triac Sink with Separate Transformer VC Transformer N0067-7/11 - Subject to change. elimo ircontrols (US), Inc. Hot Com Controller Triac Source VC Transformer Hot Com 11 6 Red () + Hot Wht () Y 1 Input Pnk () Y Input Org () U Output to 10 V Red () + Hot Wht () Y 1 Input Pnk () Y Input Org () U Output to 10 V VC Transformer Hot Com Controller VC Transformer Red () + Hot Wht () Y 1 Input Pnk () Y Input Org () U Output to 10 V Controller 800--908 US 866-80-7089 CND 0-791-896 LTIN MERIC / CRIEN 1
W 11 Wiring for Damper ctuators and Control Valves Wiring Multiple MFT ctuators Control Type: PWM CUTION ctuators may be connected in parallel if not mechanically mounted to the same shaft. Power consumption and input impedance must be observed. ctuators may also be powered by VDC. 8 INSTLLTION NOTES ctuators with plenum rated cable do not have numbers on wires; use color codes instead. ctuators with appliance cables are numbered. Control signal may be pulsed from either the Hot or Common VC line. WRNIN Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Wiring multiple...mft actuators to single shaft and/or on valves. ll MFT actuators are wired in master-slave configuration. Pulse Width Modulation Position Feedback VDC 0 to VDC VC Transformer (C Only) ( ) (+).1 to. sec 8 Master Red () + Hot Wht () Y Input Org () U Output to 10 VDC CCW CW MFT actuator configurations should also co-ordinate with each other. Meaning the master input = controllers output. Master output = slave input. Slave output = controller input. Slave Example Controller Output Master Feedback Slave Input Slave Feedback 0.1 to. sec to 10 VDC to 10 VDC 0 to VDC Multiple ctuators Mounted to One Control Shaft Model Max. Qty Per Shaft Torque enerated EF-MFT(-S) EFX-MFT(-S) 810 in-lb F-MFT(-S) FX-MFT(-S) in-lb MX()-MFT 60 in-lb KX()-MFT 60 in-lb Red () + Hot Wht () Y Input to 10 VDC Org () U Output CCW CW N0067-7/11 - Subject to change. elimo ircontrols (US), Inc. 800--908 US 866-80-7089 CND 0-791-896 LTIN MERIC / CRIEN
Wnew6008_6 Wiring for Damper ctuators and Control Valves Spring Return and Non-Spring Return, V for use with Honeywell Electronic Series 90, or a 0 to 1 Ω input ctuators: F-MFT9 FX-MFT9 MX-MFT9 MX-MFT9 NMX-MFT9 LMX-MFT9 N0067-7/11 - Subject to change. elimo ircontrols (US), Inc. 1 Wire Colors 1 = lack = Red Override INSTLLTION NOTES ctuators with plenum rated cable do not have numbers on wires; use color codes instead. ctuators with appliance cables are numbered. Provide overload protection and disconnect as required. ctuators and controller must have separate transformers. Consult controller instruction data for more detailed information. Resistor value depends on the type of controller and the number of actuators. No resistor is used for one actuator. Honeywell resistor kits may also be used. To reverse control rotation, use the reversing switch. Switch Switch Damper Position Damper Open Damper Closed The direction of rotation switch is set so that the fail safe position and the position of the damper is closed with no signal at wire R. 1 VC Transformer 1 Low Limit Control 1 W Series 90 Controller R VC Transformer 1 Ω = White = Pink W R Controller VC Transformer W R Series 90 low limit control 1 Ω for 0 to 0% control 80 Ω for 0 to 100% control Red () + Hot Pnk () W Wht () R ry () = ray 6 = Orange Org (6) U Output to 10 VDC -MFT9 Red () + Hot Pnk () W Wht () R ry () -MFT9 Org (6) U Output to 10 VDC Red () + Hot Pnk () W Wht () R ry () Org (6) U Output to 10 VDC -MFT9 W01 W016 High Limit Control 1 W Series 90 Controller R VC Transformer 1 1 VC Transformer Series 90 high limit control - 80 Ω R W Red () + Hot Pnk () W Wht () R -MFT9 ry () Org (6) U Output to 10 VDC Wiring Multiple ctuators to a Series 90 Controller Shunting Resistor W R Series 90 Controller No. of actuators Resistance 10 Ω 71. Ω 7. Ω 7. Ω 6 8 Ω Resistor Kit No. Z-R0 To other actuators Red () + Hot Pnk () W Wht () R ry () Org (6) U Output to 10 VDC -MFT9 Red () + Hot Pnk () W Wht () R ry () Org (6) U Output to 10 VDC -MFT9 Wiring Multiple ctuators to a Series 90 Controller using a Minimum Position Potentiometer 1 VC Transformer Series 90 Controller R W R W Shunting Resistor 1 R W H0 Changeover Controller Occupied Contact To other actuators S96 Minimum Position Potentiometer Red () + Hot Pnk () W Wht () R ry () Org (6) U Output to 10 VDC -MFT9 Red () + Hot Pnk () W Wht () R ry () Org (6) U Output to 10 VDC -MFT9 W017 W018 W019 Typical wiring diagrams for multiple actuators used with the W97, W7100 and T77 controllers 1 H0 Changeover Controller W Shunting Resistor W97, W7100 Controller 1 VC Transformer No. of actuators Resistance 100 Ω 910 Ω 768 Ω Resistor Kit No. Z-R06 1 W R Shunting Resistor W97, W7100 T77 Y R 1 R R W W R W Q09 Minimum Position Potentiometer To other actuators To other actuators Red () + Hot Pnk () W Wht () R ry () Org (6) U Output to 10 VDC -MFT9 Occupied Contact Honeywell T67 Morning Warmup Red () + Hot Pnk () W Wht () R ry () Org (6) U Output to 10 VDC -MFT9 Used with the W97 and W7100 controllers VC Transformer R R W W Honeywell T67 Morning Warmup Honeywell Q09 Minimum Position Potentiometer Red () + Hot Pnk () W Wht () R ry () Org (6) U Output to 10 VDC -MFT9 Red () + Hot W00 Pnk () W Wht () R ry () Org (6) U Output to 10 VDC -MFT9 800--908 US 866-80-7089 CND 0-791-896 LTIN MERIC / CRIEN
W609_11 Wiring for Damper ctuators and Control Valves Proportional, Spring Return, V, 6 to 9 VDC Output Power Supply 0 VDC provides power to controllers ctuators: LF-MFT-0 US LF-MFT-S-0 US CUTION ctuators may be connected in parallel. Power consumption and input impedance must be observed. WRNIN Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. 6 to 9 VDC Control of LF-MFT (-S) -0 US 1 VC Transformer Control Signal 6 to 9 VDC (+) Power to Controller Controller Common ( ) Feedback -10 VDC lk (1) Red () Wht () Common + Hot Y Input, 6 to 9V Wht () Output +0 VDC Wht () U Output to 10V Wht (6) Common +0 VDC LF-MFT (-S) -0 US Multiple LF-MFT (-S) -0 US ctuators from One Controller 1 VC Transformer CW CCW W07 W09 1 INSTLLTION NOTES ctuators may also be powered by VDC Provide overload protection and disconnect as required. Control Signal 6 to 9 VDC (+) Feedback -10 VDC Red () + Hot Wht () Y Input, 6 to 9V Wht () Output +0 VDC Wht () U Output to 10V Power to Controller Wht (6) Common +0 VDC Typical Control Wiring for MP-XX Series ctuators to Controllers Requiring External 0 VDC Power Supply 1 CP-810 TP-810X TP-811 TP-81 TP-8 Typical Controller +0 (Red) OP1 (Yellow) COM (lue) Vac: lack/lue 10 Vac: White 0 Vac: White/lack elimo modulating actuators are VC/DC, if 10 or 0 is available an external transformer is required. Maximum of MP-XX-00 models include internal SPDT auxiliary switch. Vac Power ux. Switch 1 lack Red Yellow lue rown Orange reen MP-XX N.C. COM N.O. Wire cross reference elimo MP-XX (SR or MFT) lack/lue, Power, Hot lack, Power 1, Com Red, +0, +0 VDC Yellow, OP1, Signal lue, COM 6, Com VDC rown, N.O. S, N.O. -S type Orange, N.C. S, N.C. -S type reen, round Not used W1 Controller Common ( ) 1 VC Transformer To other actuators CW CCW LF-MFT (-S) -0 US Red () + Hot Wht () Y Input, 6 to 9V Wht () Output, +0 VDC Wht () U Output to 10V Wht (6) Common +0 VDC CW CCW LF-MFT (-S) -0 US N0067-7/11 - Subject to change. elimo ircontrols (US), Inc. Refer to page 6 for auxiliary switch (-S models) wiring. 800--908 US 866-80-7089 CND 0-791-896 LTIN MERIC / CRIEN
W 11 Wiring for Damper ctuators and Control Valves Wiring Multiple MFT ctuators Control Type: VDC or -0m MFT9 CUTION ctuators may be connected in parallel if not mechanically mounted to the same shaft. Power consumption and input impedance must be observed. WRNIN Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. VDC or -0m Control Signal to 10 VDC or to 0 m Maximum actuators per shaft. VC Transformer ( ) (+) 00 Ω 1/ watt Master Red () + Hot Wht () Y Input, to 10 V Org () U Output to 10 V CCW CW Slave Red () + Hot Wht () Y Input, to 10 V Org () U CCW CW INSTLLTION NOTES N0067-7/11 - Subject to change. elimo ircontrols (US), Inc. ctuators may also be powered by VDC. 1 Wiring multiple...mft actuators to single shaft and/or on valves. ll MFT actuators are wired in master-slave configuration. MFT actuator configurations should also co-ordinate with each other. Meaning the master input = controllers output. Master output = slave input. Slave output = controller input. Example Controller Output ctuators with plenum rated cable do not have numbers on wires; use color codes instead. ctuators with appliance cables are numbered. Provide overload protection and disconnect as required. Consult controller instruction data for more detailed information. To reverse control rotation, use the reversing switch. Master Feedback Slave Input Slave Feedback to 10 VDC to 10 VDC to 10 VDC 0 to VDC Multiple ctuators Mounted to One Control Shaft 1 VC Transformer W R Master Red () + Hot Wht () W Pnk () R ry () Org (6) U Output, to 10 V -MFT9 Slave Red () + Hot Wht () Y 1 Input Pnk () Y Input Org (6) U Output to 10 V CCW CW -MFT Multiple ctuators Mounted to One Control Shaft Model Max. Qty Per Shaft Torque enerated EF-MFT(-S) EFX-MFT(-S) 810 in-lb F-MFT(-S) FX-MFT(-S) in-lb MX()-MFT 60 in-lb KX()-MFT 60 in-lb 800--908 US 866-80-7089 CND 0-791-896 LTIN MERIC / CRIEN
W 11 Wiring for Damper ctuators and Control Valves uxiliary Switch Wiring ctuators: EF...-S EFX...-S F...-S FX...-S F...-S US NF...-S NFX...-S LF...-S US TF...-S US M(X)...-S LM(X)...-S R(X)...-S LR(X)...-S S1/S LM(X)...(-P)(-P10) INSTLLTION NOTES PPLICTION NOTES 1 1 One built-in auxiliary switch (1xSPDT), for end position indication, interlock control, fan startup, etc. Two built-in auxiliary switches (xspdt), for end position indication, interlock control, fan startup, etc. WRNIN Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. uxiliary Switch Wiring for EF...-S, EFX...-S, F...-S, FX...-S, NF...-S, NFX...-S S1 S S S S S6 NC NO NC NO EF -S EFX -S 10 10 to 90 10 to 8 for EF... F -S FX -S uxiliary Switch Wiring for F -S US S1 S S S S S6 NC NO NC NO F -S US dd on uxiliary Switches S1/S for M(X), M(X), NM(X), LM(X), R(X), R(X), NR(X), LR(X) to 8 NF -S NFX -S 1 1 Meets culus requirements without the need of an electrical ground connection. Same voltage must be used for dual switch models. Either VC or line voltage, not both. uxiliary Switch Wiring for LF -S US, TF -S, LM(X)--S, M(X)--S, LR(X)--S, R(X)--S S1 S S NC NO 0 to 9 LF -S US TF -S US LM(X)--S M(X)--S LR(X)--S R(X)--S uxiliary Switch Ratings Product Voltage EF...-S, EFX...-S F...-S, FX...-S F...-S US NF...-S, NFX...-S LF...-S US TF...-S US M(X)...-S LM(X)...-S R(X)...-S LR(X)...-S S1, S 0 0 0 0 0 0 0 0 0 0 0 1 Resistive Load.0.0 7.0.0.0.0.0.0.0.0.0 Potentiometer and uxiliary Switch Wiring for LM(X)-(-S)(-P)(-P10) Inductive Load 0. 0.. 0. 0. 0. 0. 0. 0. 0. 0. N0067-7/11 - Subject to change. elimo ircontrols (US), Inc. S1 S S NC NO S1 S1 S S S S S6 NC NO NC NO Potentiometer /10K Ω uxiliary Switch S 6 800--908 US 866-80-7089 CND 0-791-896 LTIN MERIC / CRIEN
Interface Wiring Detail SYx-MFT, V, 10/0V ctuators: SYx-MFT INSTLLTION NOTES CUTION Notes: 1. Motor CMS have been factory calibrated and should not be moved.. n adaption must be performed if any limit switch is adjusted. This will calibrate the beginning and end stopping points. Press the adaption button for seconds and release. MFT Connection Control Signal + Control Signal - FDK + FDK - daption N0067-7/11 - Subject to change. elimo ircontrols (US), Inc. Control Signal + Control Signal - FDK + FDK - Direction of Rotation N H V daption Direction of Rotation 10/0V 800--908 US 866-80-7089 CND 0-791-896 LTIN MERIC / CRIEN 7
SYx-P Interface Wiring Detail LED Open LED Close N Power Supply () + Power Supply () Control Signal (6) Control Signal (7) Sensitivity switch setting is position # for factory default. To widen deadband, select a higher number (up to 9). Sensitivity Feedback (11) Feedback (1) VR VR1 INSTLLTION NOTES CUTION Notes: 1. Do not change sensitivity or dip switch settings with power applied!. VR1 and VR are factory calibrated and should not be moved.. Motor CMS have been factory calibrated and should not be moved. Dip Switch Settings 8 7 6 1 OFF ON INPUT = -10 VDC 8 7 6 1 OFF ON RESPONSE = DIRECT 8 7 6 1 OFF INPUT = -0m 8 7 6 1 OFF RESPONSE = REVERSE ON ON WRNIN Potentiometer (Factory Pre-set) 8 7 6 1 8 7 6 1 8 7 6 1 OFF ON OFF ON OFF ON INPUT = 1- VDC OUTPUT = -0m OUTPUT = -10 VDC 8 7 6 1 8 7 6 1 8 7 6 1 For -position actuators with 1k feedback option Potentiometer points 1,, are wired to terminal blocks 8, 9, 10. When a valve is closed: 8, 9 1k Ω 9, 10 0k Ω When a valve is opened: 8, 9 0k Ω 9, 10 1k Ω OFF ON OFF ON OFF ON LOSS OF SINL = CLOSED (Direct cting) LOSS OF SINL = OPEN (Reverse cting) LOSS OF SINL = OPEN (Direct cting) LOSS OF SINL = CLOSED (Reverse cting) LOSS OF SINL = STOP N0067-7/11 - Subject to change. elimo ircontrols (US), Inc. *On modulating actuators DO NOT master/slave using optional potentiometer. For modulating actuators with 1k feedback option* Potentiometer points 1,, are wired to terminal blocks 8, 9, 10. When a valve is closed: 8, 9 1k Ω 9, 10 0k Ω When a valve is opened: 8, 9 0k Ω 9, 10 1k Ω 8 800--908 US 866-80-7089 CND 0-791-896 LTIN MERIC / CRIEN