TECHNICAL DATASHEET #TDAX06070X Triaxial Inclinometer with Gyro ±180⁰ Pitch/Roll Angle Pitch Angle Rate Acceleration SAE J1939, Analog Output or RS-232 Options 2 M12 Connectors, IP67 with Electronic Assistant P/N: AX06070X An internal gyroscope minimizes the influence of dynamic linear acceleration on slope sensor readings. Features: Reliable, real-time, accurate and stable slope angle data MEMS-based accelerometer measures angle with respect to gravity MEMS gyroscope measures angular rate around the axis Measures pitch and roll inclination angles in a full ±180 degree orientation range Outputs accelerations in 3 orthogonal directions Provides an angular rate of rotation of the pitch angle Output: SAE J1939 12V, 24Vdc nominal power supply Aluminum enclosure, 2 round 5-pin A-coded M12 connectors, gasket, encapsulation IP67 protection CE mark pending Configurable using the Electronic Assistant Applications: Level, tilt, pitch and acceleration monitoring in agricultural, off-highway and mining equipment Platform levelling and stabilization in industrial machines Robotics position sensing Navigation system component Ordering Part Numbers: Inclinometers: AX060700 Triaxial Inclinometer, (SAE J1939) Accessories: Electronic Assistant over (SAE J1939): P/N: AX070502
Description: The Triaxial Inclinometer measures pitch and roll inclination angles in a full ±180 degree orientation range. Pitch angle is compensated by a gyroscope to minimize the influence of dynamic linear accelerations. The unit can also output gravity angle and unit accelerations in three orthogonal directions as well as an angular rate of rotation around the pitch angle. The angles are measured by a set of MEMS sensors, which senses acceleration caused by the gravity force in three orthogonal directions. The output signals from the MEMS sensors are normalized and processed by a microcontroller. Inclinometer model options include: networking via SAE J1939. Refer to the block diagram below. The inclinometer is IP67 rated and is packaged in a cast Aluminum housing. A dual 5-pin M12 connector configuration allows for networking the sensor in a machine control system. Other configurations are available on request. The inclinometer transmits angular and angular rate data over the bus using a standard J1939 protocol. The unit s default configuration can be changed using the PC-based Axiomatic Electronic Assistant software. Block Diagram BAT+ BAT EMI Filter. Transient and Reverse Polarity Power Supply _SHIELD 3D Accelerometer _HI _LO p/n AX060701 1D Gyroscope ARM Cortex M3 Microcontroller Voltage Output VOUT_1 VOUT_2 VOUT_3 VOUT_4 AGND p/n AX060702 RS232 RS232_TXD RS232_RXD RS232_GND TDAX06070X 2
Unit Orientation Z X Roll Y Pitch Y Pitch X Roll Z Technical Specifications: Specifications are indicative and subject to change. Actual performance will vary depending on the application and operating conditions. Users should satisfy themselves that the product is suitable for use in the intended application. All our products carry a limited warranty against defects in material and workmanship. Please refer to our Warranty, Application Approvals/Limitations and Return Materials Process as described on www.axiomatic.com/service.html. Power Supply Input Power Supply Input Supply Current 12V, 24V nominal (9 36 VDC power supply range) Suitable for engine cranking, jump start and load dump conditions found in mobile equipment. 45 ma maximum at 24Vdc 85 ma maximum at 12Vdc Reverse polarity and transient protection is provided. Outputs Static Parameters Inclinometer Gyroscope Measurement Range ±180ᵒ Pitch & Roll 0 180ᵒ Gravity ±100ᵒ/s Pitch Resolution ±0.35ᵒ Maximum (All angles, except angle listed below.) 0.1ᵒ (Pitch angle with gyro compensation) Effective resolution (3.46* NoiseRMS) at cut-off frequency, Fc=5Hz ±0.11ᵒ/s Effective Resolution (3.46*NoiseRMS). Maximum at cut-off frequency, Fc=5Hz Initial Accuracy ±1.5º Maximum, at 25ºC ±2.5º/s Maximum, at 25ºC Temperature Drift ±1.5ºC Maximum, at 0º over the full temperature range -40 85ºC ±1.2º/s Maximum, at 0º over the full temperature range -40 85ºC Nonlinearity ±0.7% Maximum @ 25 ºC ±0.5% Maximum @ 25 ºC Cross-Axis Sensitivity ±2.5% Maximum @ 25 ºC ±1.7% Maximum @ 25 ºC Dynamic Parameters Inclinometer Gyroscope Cut-off frequency, Fc User configurable 1 50 Hz (5 Hz default) User configurable 1 50 Hz (5 Hz default) Settling Time <0.2 s Typical at default Fc. From 0 to 95% of the static output value. <0.1 s Typical at default Fc. From 0 to 95% of the static output value. TDAX06070X 3
Parameters ISO 11898 Model AX060700: Electrical Connections Model AX060700 1 or 2 ports depending on model SAE J1939 (open is available on request.) For data transmission and for access to the configuration of the inclinometer. By default, the inclinometer transmits angular and angular rate information on the network in PGN 61459, Slope Sensor Information. User configurable PGNs are also available on request. Short circuit to ground Connection to the power supply (24V maximum) 120 Ohm terminated twisted pair, baud rate up to 1MBit/s. Termination resistor is not installed. A mating plug with termination, P/N: AX070114, can be ordered for applications requiring a termination of the network. 1 port, SAE J1939 There is only one port supported by the unit. Both connectors are physically connected together to facilitate cable routing in the user system. General Specifications Microprocessor Sensors Control Logic User Interface Operating Conditions Enclosure and Dimensions CE Compliance Vibration and Shock STM32, 32-bit, 128 Kbyte flash program memory MEMS acceleration and MEMS gyroscope sensors User programmable functionality using Axiomatic Electronic Assistant Axiomatic Electronic Assistant, P/N: AX070502-40 to 85 C (-40 to 185 F) Cast Aluminum enclosure 2 Round M12 5-pin A-coded integral connectors Encapsulated, Lid Gasket Dimensions: 2.90 x 5.35 x 1.42 inches 73.66 x 135.99 x 36.16 mm (L x W x H) IP67 CE mark pending for EMC Directive RoHS compliant The sinusoidal component of the vibration testing was conducted following MIL-STD- 202G, method 204D, test condition C (10g peak). A resonant frequency analysis was performed, no resonances were noted. Sweep Characteristic: 10Hz to 2000Hz to 10Hz Sweep Period: 20 Minutes Test Duration: 8hrs/axis Test Intensity: 10g Peak The random component of the vibration testing was conducted meeting or exceeding the requirements of MIL-STD-202G, method 214A, test condition I/B (7.68 Grms): Frequency Range: 5Hz to 2000Hz Test Duration: 8hrs/axis Overall Grms: 7.68 Grms TDAX06070X 4
The shock component of the vibration testing is based on MIL-STD-202G, method 213B, test condition A. The pulse duration was shortened to 9 ms from the standard 11 ms due to our vibration system limits. Eight pulses per axis were performed instead of six. The test was conducted as follows: Pulse Type: half sine Pulse Duration: 9 ms Peak Value: 50 g Pulses per axis: 8 Weight 0.85 lb, 0.39 kg Installation Mounting holes accept #10 or M6 screws. The thickness of the mounting flange is 0.25 inch or 6.35 mm. The wiring is considered intrinsically safe. All field wiring should be suitable for the operating temperature range of the module. wiring may be shielded using a shielded twisted conductor pair and the shield must be grounded on the other end. All chassis grounding should go to a single ground point designated for the machine and all related equipment. Dimensions Note: open is a registered community trade mark of in Automation e.v. Form: TDAX06070X-10/02/17 TDAX06070X 5