By Garrett Strong www.makemoneywelding.com

Copyright MakeMoneyWelding.com All rights reserved. No part of this publication may be reproduced or transmitted in any form or by any means, mechanical or electronic, including photocopying and recording, or by any information storage and retrieval system, without permission in writing from the publisher.

The 3 Most Dangerous Mistakes Beginner Welders Make And How To Avoid Them There are 3 mistakes that most new welders make that I want to share with you before you begin your journey learning to weld. If you follow what I say here and you don t make these mistakes then your welding experience will go much more smoothly. Beginner Mistake #1: Not controlling the heat and weld puddle resulting in poor weld penetration and poor weld strength. No matter what welding process you re using, whether it s tig, mig, arc, or oxy acetylene welding, heat control is the thing to keep in mind. Make sure that you always take your time and get good weld penetration. If you rush the weld bead and go too fast you will risk getting a cold weld with little to no penetration, resulting in a weak weld and possible weld failure. You definitely don t want a weld failure, especially if you re welding structural things like railings or trailers.

Make sure that you re going slow enough to get good, deep weld penetration, especially if you re welding thicker steel. If you are welding anything thicker than 1/8 steel then you definitely want to bevel the work piece so that you get maximum penetration of the weld through the entire piece. You can even run multiple weld beads if you need to ensure the work piece is as strong as possible. Since you re just starting off welding you probably don t really have a clue what kind of penetration your welds are getting on the metal, so the best thing to do is to perform a break test. What s a break test? It s exactly as it sounds. Place one of your practice pieces in a vice, grab a hammer and see if you can manage to break the weld. If it breaks with little effort then you know you have a cold weld, with little penetration.

If you have a portable band saw you could also do a cross cut in the work piece to see how well your weld penetrated. Whatever you do, just make for certain that if you re welding something that is going to be used for structural purposes that you have practiced and are confident in your welding abilities. There is another fatal mistake that many new welders make that can not only cause ugly welds, but will also cause weld failure if done improperly. Beginner Mistake #2: Not properly cleaning and fitting up the metal before welding, resulting in crappy weld appearance and poor strength. Welding on painted metal, dirty metal, rusted metal, etc. is a HUGE no, no. I can t tell you how many times I ve seen this. Someone thinks that they re just going to repair something and they don t give a second thought about cleaning the metals surface. Sloppy Weld Nice Weld

It s an absolute must that you clean the metal by either grinding off the rust, paint, oil, dirt, etc. before you lay down a weld bead. You do not want the impurities from those things included in your weld as it will weaken your welds. Even if you re working with clean metal there is a layer of mill scale that should be grinded off before welding. This layer of mill scale occurs as the steel is heated and cooled at the steel mill. If you fail to clean the work piece before welding it will be more difficult to get good weld penetration because the rust, paint, dirt, etc. will take away heat from the actual surface of the metal and the weld. You can accomplish metal cleaning by using an angle grinder, and with certain projects you might want to clean the metal surface with acetone before welding. So, make sure you are using proper pre-weld cleaning techniques before you weld to ensure you get great looking welds with high strength. There is one last mistake I want to share that I see way too many beginner welders making.

Beginner Mistake #3: Using improper safety precautions when welding, cutting, and grinding resulting in fatal damage to your body. When you begin welding you re going to be working with a lot of new equipment that you may or may not be accustomed to using. You ll be using things like cutting torches, grinders, welders, drills, hot metal, etc. The thing you want to keep in mind when welding is that safety is your best friend, and should come first ALWAYS! You can easily hurt your eyes when welding because of the ultra-violet light that the arc welding process emits. You want to ensure that you have a welding mask with at least a #9 welding lens, and I recommend a #10 or #11 if possible. The ultra-violet light can not only damage your eyes, it can also do a lot of damage to your skin as well. That s why whenever you weld you need to make sure you have long pants, and a long sleeve shirt to protect you.

I recommend wearing some kind of boots as well. Steel toe boots would be ideal. Make certain you don t have any synthetic clothing on like a jogging jacket or pants because those materials will melt right to your skin if you get a hot spark on you. I ve seen the shows on TV like American Choppers where those guys just weld without proper arm protection, and many times they don t have a mask on, welding with closed eyes. This is really setting a bad safety example for people who are just learning to weld. Don t do as they do. Put safety first always. You will also likely be working with a grinder at some point, and those can get very loud and emit a lot of sparks. Make sure you have some ear plugs handy, along with a clear face shield to protect you from the sparks. Those sparks can put your eye out for good, so just be smart. Since I began welding I ve been burned by hot metal many times. A couple of times I just forgot I wasn t wearing my leather

welding gloves and I picked up a piece of hot metal with my bare hand. It hurt, so just make sure you have some good gloves and a pair of pliers to pick up the hot metal. Lastly, I want to talk about oxy acetylene. Since you are new to welding you may not have an oxy acetylene setup just yet. However, when you do get one just make sure you use precautions when working with it. The gases are kept under extremely high pressure, and if you improperly handle an oxygen bottle it can be very unsafe. I ve been lucky to never have an issue with my oxy acetylene setup, but I ve seen videos where they ve either blown up or shot off like a rocket due to improper storage or handling. If you follow the operating instructions then you ll have nothing to worry about. I hope this free report has helped you to avoid the most common mistakes beginners make. Regards,

-Garrett