CLG-50 s e ries IP65 IP67 SPECIFICATION MODEL CLG-50- CLG-50-5 CLG-50-0 CLG-50-4 CLG-50-30 CLG-50-36 CLG-50-4 OUTPUT INPUT PROTECTION ENVIRONMENT SAFETY & EMC OTHERS NOTE DC VOLTAGE CONSTANT CURRENT REGION Note.4 9 ~V RATED CURRENT RATED POWER VOLTAGE ADJ. RANGE Note.6 9 ~ 3V CURRENT ADJ. RANGE LINE REGULATION LOAD REGULATION SETUP, RISE TIME HOLD UP TIME (Typ.) VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR (Typ.) EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT(max.) LEAKAGE CURRENT WORKING TEMP. WORKING HUMIDITY SAFETY STANDARDS WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC EMISSION Note.5 95 ~ 0% OVER CURRENT (Typ.) Note.4 Protection type : Constant current limiting, recovers automatically after fault condition is removed OVER VOLTAGE OVER TEMPERATURE STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION Note.7 V RIPPLE & NOISE (max.) Note. VOLTAGE TOLERANCE Note.3 SHORT CIRCUIT EMC IMMUNITY 5V.5 ~ 5V 0V 5 ~ 0V I/P-O/P:3.75KVAC I/P-FG:.KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:00M Ohms / 500VDC / 5 / 70% RH MTBF 303.7Khrs min. MIL-HDBK-7F (5 ) DIMENSION.**mm (L*W*H)(CLG-50-Blank/A/B) 9**mm (L*W*H)(CLG-50-C) PACKING.0Kg; pcs/3kg/0.5cuft(clg-50-blank/a/b) Kg; pcs/3kg/0.96cuft(clg-50-c) 4V ~ 4V 30V.5 ~ 30V 36V 7 ~ 36V A 9.5A 7.5A 6.3A 5A 4.A 3.A 4V 36 ~ 4V 3W 4.5W 50W 5.W 50W 5.W 53.6W 5.5 ~ A.0% 3 ~ 7V 4.75 ~ 9.5A.0% 7 ~ V 3.75 ~ 7.5A.0% ~ 7V Can be adjusted by internal potentiometer or through output cable 3.5 ~ 6.3A 6 ~ 3V.5 ~ 5A 3 ~ 4V. ~ 4.A 00mVp-p 40 ~ 56V.6 ~ 3.A 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 3000ms, ms at full load 30VAC /5VAC 50ms / 30VAC 6ms / 5VAC at full load 90 ~ 95VAC 7 ~ 47VDC 47 ~ 63Hz PF>0.9/5VAC, PF>0.95/30VAC, PF>0.93/77VAC at full load (Please refer to "Power Factor Characteristic" curve) % % 90% 90% 9% 9% 9% A / 5VAC A / 30VAC 0.A / 77VAC COLD START 65A/30VAC <ma / 40VAC Hiccup mode, recovers automatically after fault condition is removed 3.5 ~ 6V ~ 0V 3 ~ 7V ~ V 33 ~ 36V 4 ~ 4V 59 ~ 70V Protection type : Shut down and latch off o/p voltage, re-power on to recover 00 0 (RTH) Protection type : Shut down o/p voltage, re-power on to recover -30 ~ +70 (Refer to "Derating Curve") 0 ~ 95% RH non-condensing -40 ~ +, 0 ~ 95% RH 0.03%/ (0 ~ 50 ) 0 ~ 500Hz, 5G min./cycle, period for 7min. each along X, Y, Z axes UL750, CSA C. No. 50.0-0, UL0, CAN/CSA-C. No. 07.-0, EN67-, EN67--3 independent (except for CLG-50 C type), UL60950-, TUV EN60950-,IP65 or IP67, J67-(option, except for CLG-50 C type), J67--3 approved Compliance to EN5505, EN550 (CISPR) Class B, EN6000-3- Class C ( 75% load) ; EN6000-3-3 Compliance to EN6000-4-,3,4,5,6,,, EN6547, EN5504, light industry level (surge 4KV), criteria A
Mechanical Specification Blank:(CLG-50) Case No. 954A Unit:mm. SJTW AWG 3C 9.4 9.4. SJTW 4AWG C : Max. Case Temperature. IP67 rated. Cable for I/O connection. A Type:(CLG-50-_A). SJTW AWG 3C 9.4 9.4. Io ADJ. Vo ADJ. SJTW 4AWG C : Max. Case Temperature. IP65 rated. Output voltage and constant current level can be adjusted through internal potentiometer. (Can access by removing the rubber stopper on the case.)
B Type:(CLG-50-_B). SJTW AWG 3C 9.4. 9.4 SJTW 4AWG C SJTW AWG C ADJ(Blue) ADJ(White) : Max. Case Temperature. IP67 rated. Output constant current level can be adjusted through output cable by connecting a resistor between ADJ and ADJ. Reference resistance value for output current adjustment (Typical) Resistance Open 4.7K 60 Short Percentage of rated current Slightly > 00% 00% 75% 50% Slightly < 50% C Type:(CLG-50-_C) 5.4 9 I/P 7.5 9.5 3 37 Io ADJ. Vo ADJ. O/P AC Input Terminal Pin No. Pin No. 3 FG AC/N AC/L : Max. Case Temperature. DC Output Terminal Pin No. Pin No. +V -V Output voltage and constant current level can be adjusted through internal potentiometer. (Can access by removing the rubber stopper on the case.)
Block Diagram Fosc : 00KHz I/P FG EMI FILTER & RECTIFIERS PFC CIRCUIT PFC CONTROL O.L.P. POWER SWITCHING PWM & PFC CONTROL RECTIFIERS & FILTER O.L.P. DETECTION CIRCUIT O.V.P. +V -V ADJ ADJ (B Type) Derating Curve Static Characteristics 00 30VAC 00 90 60 30VAC Input only 00VAC 70 LOAD (%) 40 0 LOAD (%) 60 50 40-30 -5-0 0 5 30 50 55 60 70 AMBIENT TEMPERATURE ( ) (HORIZONTAL) 90 00 5 35 45 55 65 75 00 30 95 INPUT VOLTAGE (V) 60Hz
Power Factor Characteristic PF. 0 0 0. 9 0. 9 6 0. 9 4 0. 9 0. 9 0 0. 0. 6 0. 4 0. 0. 0 0. 7 Constant Current Mode 5 0 % 6 0 % 7 0 % 0 % 9 0 % 0 0 % LOAD (50W) 7 7 V a c 3 0 V a c 5 V a c EFFICIENCY vs LOAD (4V Model) possess superior working efficiency that up to 9% can be reached in field applications. 96 9 EFFICIENCY (%) 4 76 7 64 0% 0% 30% 40% 50% 60% 70% % 90% 00% 77Vac 30Vac 5Vac LOAD DRIVING METHODS OF LED MODULE There are two major kinds of LED drive method "direct drive" and "with LED driver". A typical LED power supply may either work in "constant voltage mode (CV) or constant current mode (CC)" to drive the LEDs. Mean Well's LED power supply with CV+ CC characteristic can be operated at both CV mode [with LED driver, at area (A)] and CC mode [direct drive, at area (B)]. 00 Vo(%) (A) Constant Voltage area (B) Constant Current area 75 (max.) (C) Hiccup Protection 75 00 Io (%) Typical LED power supply I-V curve