Specifications Table Type Power Rating Resistance Tolerance Nominal Resistance MC 0603 0.0625W (1/16W) ±1% 10Ω Ratings: Type MC 0603 Power Rating 0.0625W (1/16W) Max. Working Voltage 50V Max. Overload Voltage 100V Temperature Range -55 C to +155 C Ambient Temperature 70 C Power Rating: Resistors shall have a power rating based on continuous load operation at an ambient temperature of 70 C. For temperature in excess of 70 C, The load shall be derate as shown in figure. Derating Curve Page <1> 20/02/15 V1.1
Nominal Resistance: Effective figures of nominal resistance shall be in accordance with E-24 and E-96 series E-96 series for 1 % and E-24 series for 2 % and 5 % Construction: Power Rating and Dimensions: Dimension : Type Dimension (mm) L ± 0.1 W + 0.15 / 0.1 H ±0.1 l1 ±0.2 l2 ±0.2 MC 0603 1.6 0.8 0.45 0.3 0.3 Power Rating : Type Power Rating Tolerance Resistance Standard Series MC 0603 0.0625W (1/16W) ±1 10Ω ~ 1MΩ E-24 Page <2> 20/02/15 V1.1
Performance Specification : Characteristics Insulation resistance Dielectric withstanding voltage Temperature coefficient Short time overload Solderability Limits 1,000 MΩ or more No evidence of flashover mechanical damage, arcing or insulation break down 1Ω - 10Ω : ± 400 PPM/ C 11Ω - 100Ω : ± 200 PPM/ C >100Ω : ± 100 PPM/ C ± (1.0% + 0.1Ω) Max. 95 % coverage Min. Test Methods ( JIS C 5201-1 ) Apply 500V DC between protective coating and termination for 1 min, then measure Apply 500V AC between protective coating and termination for 1 minute Natural resistance change per temp. degree centigrade. R 2 -R 1 10 6 (PPM/ C) R 1 (t 2 -t 1 ) R 1 : Resistance value at room temperature (t1) R 2 : Resistance value at room temp. plus 100 C (t2) Permanent resistance change after the application of a potential of 2.5 times RCWV for 5 seconds Test temperature of solder : 245 ± 3 C Dwell time in solder : 2 ~ 3 seconds Wave soldering condition: (2 cycles Max.) Pre-heat : 100 C to 120 C, 30 ± 5 sec. Suggestion solder temp.: 235 C to 255 C, 10 sec. (Max.) Peak temp.: 260 C Reflow soldering condition: (2 cycles Max.) Pre-heat : 150 C to 180 C, 90 C to 120 sec. Suggestion solder temp.: 235 C to 255 C, 20 to 40 sec. Peak temp.: 260 C Soldering temp. Reference Electrical characteristics shall be satisfied. Without distinct deformation in appearance. (95 % coverage Min.) Hand soldering condition: The soldering iron tip temperature should be less than 300 C and maximum contract time should be 5 sec. Page <3> 20/02/15 V1.1
Characteristics Soldering Heat Temperature cycling Limits : ±(1% +0.05Ω) Max. ± (0.5% +0.05Ω) Max. Test Methods ( JIS C 5201-1 ) Dip the resistor into a solder bath having a temperature of 260 C ±3 C and hold it for 10 ±1 seconds. Resistance change after continuous 5 cycles for duty cycle specified below : Step Temperature Time 1-55 C ± 3 C 30 mins 2 Room temp. 10 to 15 mins 3 +155 C ± 2 C 30 mins 4 Room temp. 10 to 15 mins Load life in humidity Load Life Terminal bending ± (1% +0.1Ω) Max. ± (1% +0.1Ω) Max. ± (1% +0.05Ω) Max. Resistance change after 1,000 hours (1.5 hours on, 0.5 hour off ) at RCWV in a humidity chamber controlled at 40 C ±2 C and 90 to 95 % relative humidity Permanent resistance change after 1,000 hours operating at RCWV, with duty cycle of (1.5 hours on, 0.5 hour off ) at 70 C ±2 C ambient Twist of Test Board : Y/X = 5/90mm for 10 seconds Kit resistors: Insert for Chip Kit Dimensions : Millimetres Page <4> 20/02/15 V1.1
Album for Chip Kit: Dimensions : Millimetres Chip Kit Resistors: Product : MC Kit 1/16W (0603) +/-1% E24 Series = 121 values (10R to 1M) Quantity : 100pcs per value Total Qty : 12,100pcs. 1 10R 2 11R 3 12R 4 13R 5 15R 6 16R 7 18R 8 20R 9 22R 10 24R 11 27R 12 30R 13 33R 14 36R 15 39R 16 43R 17 47R 18 51R 19 56R 20 62R 21 68R 22 75R 23 82R 24 91R 25 100R 26 110R 27 120R 28 130R 29 150R 30 160R 31 180R 32 200R 33 220R 34 240R 35 270R 36 300R 37 330R 38 360R 39 390R 40 430R Page <5> 20/02/15 V1.1
41 470R 42 510R 43 560R 44 620R 45 680R 46 750R 47 820R 48 910R 49 1K 50 1K1 51 1K2 52 1K3 53 1K5 54 1K6 55 1K8 56 2K 57 2K2 58 2K4 59 2K7 60 3K 61 3K3 62 3K6 63 3K9 64 4K3 65 4K7 66 5K1 67 5K6 68 6K2 69 6K8 70 7K5 71 8K2 72 9K1 73 10K 74 11K 75 12K 76 13K 77 15K 78 16K 79 18K 80 20K 81 22K 82 24K 83 27K 84 30K 85 33K 86 36K 87 39K 88 43K 89 47K 90 51K 91 56K 92 62K 93 68K 94 75K 95 82K 96 91K 97 100K 98 110K 99 120K 100 130K 101 150K 102 160K 103 180K 104 200K 105 220K 106 240K 107 270K 108 300K 109 330K 110 360K 111 390K 112 430K 113 470K 114 510K 115 560K 116 620K 117 680K 118 750K 119 820K 120 910K 121 1M Part Number Table Description Resistor Kit, 0603, E24, 1% Part Number MC0603WGFE024KIT Important Notice : This data sheet and its contents (the Information ) belong to the members of the Premier Farnell group of companies (the Group ) or are licensed to it. No licence is granted for the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group s liability for death or personal injury resulting from its negligence. Multicomp is the registered trademark of the Group. Premier Farnell plc 2012. Page <6> 20/02/15 V1.1