INSTALLATION MANUAL FLAT LCD DISPLAY MOUNT MODEL CMK Ceiling
WARNING! The wall, floor or ceiling should be capable of supporting a weight of at least five (5) times the monitor s weight. If it cannot, the wall, floor o ceiling must be reinforced. Proper installation procedure by qualified personnel as outlined in the installation instructions must be adhered to Failure to do so could result in serious personal injury. CAUTION! The entire installation instructions should be fully read and understood, including all of the safety symbols and safety precautions before beginning installation. The installation instructions should be read, understood and followed to prevent personal injury or propert damage. Keep these installation instructions in an easily accessible location for future reference. CAUTION! The ceiling structure must be capable of supporting a maximum weight of 400 lbs. If not, the ceiling must be reinforced. Prope installation procedure by qualified personnel as outlined in the installation instructions must be adhered to. Failure to do so could result i serious personal injury. CAUTION! Make sure to hold the plasma display, or projector, securely and remove it from the mount to make the height adjustment prior t loosening the adjustment screws. Do not remove the screws completely from the extension loosen all at once. Loosen, remove, adjust then re tighten the screws. Failure to do so could result in injury and or damage to the plasma display or projector. Indicates that the power plug is to be disconnected from the power outlet. Safety precautions must be taken at all times. Warning and caution in general
Step 1 Screw the CMK-01 coupling adapter to the adjustable suspension adapters or 1½" (NTP) Pipe. Secure the coupling with the M6 security screw (supplied). Figure 1. AST-2446 Adjustable Ceiling Adapter Single Stud Installation Step 2 Secure the ceiling plate to the ceiling structure (see WARNING). Step 3 Use suitable hardware (commercially available) depending on your installation environment to secure the two (2) mounting points found on the ceiling plate to the ceiling structure (Figure 2). Step 4 Refer to ceiling adapter installation instructions. This hardware is commercially available and is not included in the hardware pack.
Solid Structure Installation Step 1 Secure the ceiling plate to the ceiling structure (see WARNING). Step 2 Use suitable hardware (commercially available) depending on your installation environment to secure the four (4) mounting points found on the ceiling plate to the ceiling structure (Figure 3). Step 3 Refer to ceiling adapter installation instructions. CEILING STRUCTURE (SEE WARNING) CABLE ACCESS OPENING (COMMERCIALLY AVAILABLE) SUITABLE HARDWARE ADJUSTMENT SCREWS RELOCATE ADJUSTMENT SCREWS This hardware is commercially available and is not included in the hardware pack. UPPER TUBE LOWER TUBE HEIGHT ADJUSTABLE
VESA 100: Secure the VESA 75/100 mounting bracket to the VESA 75 Using the four M4 x 10 Phillip screws. Raise and secure your monitor to the plate that has the VESA 100 now on you CMK-01 adapter and use the four (4) M4 x 10 (mm) Phillips screws (supplied) and a Phillips screwdriver. (Do not use other tools other than a Phillips screwdriver to prevent damage to the monitor or mounting points). CAUTION: Do not over tighten the screws to the monitor failure to do so could result on damaging the monitor or the mounting points. See figure 4. (4) M4 x 10mm Phillips Flat Head screws (4) M4 x 10 Phillips VESA 75 75 MM / 100 MM VESA plate Adapter Plate TENSION ADJUSTMENTS M6 X 8mm Set Screw Swivel tension Tilt tension Thank you for choosing TOA Electronics, Inc. for your installation needs. If you have any questions please contact TOA Electronics, Inc. information is shown on the front of this instruction manual.
LCD CEILING MOUNT CMK-01 LCD CEILING MOUNT Features: Tilt mount allows of adjustments up and down of ±90 from center and 360 swivel and cable access. Comes with a combination plate of VESA 75 and VESA 100 for optional mounting depending on monitor. Lbs: 2 Description Qty Size Phillips screws 4 M4 x 10 Security screw 1 M6 x 12 HARDWARE MOUNT OVERVIEW VESA 75 to VESA 100 front plate NOTE: Only used for monitors that are VESA 100 IN-CMK01.R2