Installation Instructions for Kilo S Models KILOS-CF & KILOS-SF Page 1 of 5 Instruction page index: Center Feed installation Side Feed installation 2-3 4-5
Kilo S - Instruction for center feed installation Models KILOS-XX-CF 1 2 2.2 hole Page 2 of 5 1.1 measure hub ceiling anchor location marks spacer 13/64" drill bit 2.1 wood screw drill Note: Prior to installation all 24VDC wires must be present in. Refer to the power supply installation instruction for additional information. Note: More than one person is recommended for this installation. 1.1 Measure the distance between the two hubs. Then center the fixture to the and mark the distance of the two hubs to the ceiling. 2.1 On the marked location(s), make a hole using a 13/64" drill bit. 2.2 Insert the anchor into the hole and push completely in. Insert wood screw through & washer and then tighten to secure into the anchors. 3 Prior to installing fixture to power, coaxial must be prepared to go inside assembly. If this step if skipped coaxial metal sleeve will tangle up. 4 metal sleeve wires 1 - while holding the coaxial end. 2 - Pull back about an 1-1/2" of the metal sleeve to expose the wires. 24V DC- 24V DC+ strain relief 4.2 assembly fixture power wire 3 - Cut off 1-1/2" of the wires. coaxial Note: Prior to wiring the desired fixture height must be determined to cut off any un-necessary wire. 4 - Pull forward the metal sleeve and twist to make a firmer single wire. While one person is holding the fixture, the other person can slide the coaxial end through the, & assembly. 4.2 Peel back the coaxial to expose the power wires. Connect the red (24VDC+) & black (24VDC-) power supply wires to the fixture red & black wires.
Kilo S - Instruction for center feed installation Models KILOS-XX-CF 5 6 stopper Page 3 of 5 6.1 5.1 6.2 #8-32 screw 6.3 5.2 clear film 5.1 Insert the wire nut connections into the & align the to the holes and secure using the provided two #8-32 screw. 5.2 Slide the up to the and secure by hand tightening the into the. 6.1 Untangle each and insert into the until the stopper. 6.2 Push on the and feed the into the hub until necessary. Release tab to secure in place. 6.3 Remove the clear protective film from the face of the lens. 7 7.1 threaded post aircraft 7.1 Tighten each into a. If fixture not leveled, adjustments can be made by pushing on the. Then either feed more into the hub or pull out from the hub and release to secure. Cut off any extra from the hub hole.
Kilo S - Instruction for side feed installation Models KiloS-XX-SF 1 2 2.2 hole Page 4 of 5 4-3/8" 7/8" ceiling anchor 1.1 4-3/8" canopy detail measure hub 2.1 13/64" drill bit location marks spacer wood screw drill Note: Prior to installation all 24VDC wires must be present in. Refer to the power supply installation instruction for additional information. Note: More than one person is recommended for this installation. 1.1 Align one hub to the & measure the distance from hub to the other hub. Then mark this location to the ceiling. Make addition marks if using more than one s. Use canopy detail to slighting off center hub. 2.1 On the marked location(s), make a hole using a 13/64" drill bit. 2.2 Insert the anchor into the hole and push completely in. Insert wood screw through & washer and then tighten to secure into the anchors. 3 Prior to installing fixture to power, coaxial must be prepared to go inside assembly. If this step if skipped coaxial metal sleeve will tangle up. 4 metal sleeve wires 1 - while holding the coaxial end. 2 - Pull back about an 1-1/2" of the metal sleeve to expose the wires. 24V DC- 24V DC+ strain relief 4.2 assembly fixture power wire 3 - Cut off 1-1/2" of the wires. coaxial Note: Prior to wiring the desired fixture height must be determined to cut off any un-necessary wire. 4 - Pull forward the metal sleeve and twist to make a firmer single wire. While one person is holding the fixture, the other person can slide the coaxial end through the clear s, thumb nut, & assembly. 4.2 Peel back the coaxial to expose the power wires. Connect the red (24VDC+) & black (24VDC-) power supply wires to the fixture red & black wires.
Kilo S - Instruction for side feed installation Models KiloS-XX-SF 5 6 Page 5 of 5 6.1 stopper 6.2 5.1 #8-32 screw 6.3 5.1 Insert the wire nut connections into the & align the to the holes and secure using the provided two #8-32 screw. 5.2 Slide the up to the and secure by hand tightening the into the. 5.2 clear film 6.1 Untangle each and insert into the until the stopper. 6.2 Push on the and feed the into the hub until necessary. Release tab to secure in place. For the closest to the coaxial slide through the s on the coaxial first. 6.3 Remove the clear protective film from the face of the lens. 7 7.1 8 coaxial 8.1 7.1 Tighten each into a, one will be on the and other(s) on the ceiling. If fixture not leveled, adjustments can be made by pushing on the. Then either feed more into the hub or pull out from the hub and release to secure. 8.1 If necessary make any final adjustments to the s use the s for a cleaner look. Cut off any extra from the hub hole.