AMS AMS (Advanced wire-cut EDM) Designed by an experienced and passionate team of engineering experts, AMS is proud to present the new AW-Series -- the pinnacle of modern wire cutting.built using the world's most advanced technologies and highest quality materials, the AW-Series provides your highest performance and best looking results yet. AMS's new AW-Series is a definite "must-have" for the wire-cutting expert! 1,Specifications: AW3S X.Y.Z :370x270x260 mm U.V :100x100mm Taper angle :±21 /100 mm Max. size of work piece :750x550x260 mm Max. weight of work piece:400kg Floor layout :2300x2535x2065 mm AW5S X.Y.Z :560x360x300 mm U.V :100x100mm Taper angle :±21 /100 mm Max. size of work piece :950x650x300 mm Max. weight of work piece:500kg Floor layout :2700x2845x2095 mm AW6S X.Y.Z :650x450x300 mm U.V :120x120mm Taper angle :±21 /140 mm Max. size of work piece :1000x700x300 mm Max. weight of work piece:600kg Floor layout :2575x2717x2125 mm AW9S X.Y.Z : 920x620x400 mm U.V :200x200 mm Taper angle :±21 /300 mm Max. size of work piece :1300x1000x400mm Max. weight of work piece:1000kg Floor layout :3710x3685x2315 mm
2.AW series are with the AC power circuit, can inhibit the production of soft layers and extend work piece life 3.Use of 0.1mm diameter can be automatically threading with good tension control, New design of servo control module, intelligent Threading, Cutting processes, through the screen every step of the implementation can monitoring and record every process Action time 4.TFC circuit with 5 pass function surface roughness can reach 0.2µm/Ra (at 30mm~50mm thick) 5.lift and slide front door, improve the door opening and closing swing affected personnel, cargo handling,.more convenient for the factory Aisle planning 6.Complete technical service support system, CHMER have developed the ability to control and linear motors, with full service support system for the needs of clients effectively support real-time 7.Lower maintenance costs, AMS AW series of high-precision models continue modular design, reducing maintenance costs for each electrical module, and through the cabinet design and improving the durability of each component to improve and enhance the level of electrical Loop stability and life, so that the machine cost of the initial and long-term use are to ensure that 2011/03/01 TIMTOS IN TAIPEI
10.AW 1. AW High Precision Wire-Cut EDM Function detail 1. More convenient Aisle planning in factory (Lift and slide tank door) Lift tank door with the operator convenience design thinking, just easy pull up, up and down by slide, will not affect the person on the factory goods aisle,space and aisle planning more convenient. With water No leakage problem door open 2. more safety protection (received motor anti-wrap protection cover)
3. more reliable parts of life and power module (Lower maintenance costs) Through the cabinet design and improving the durability of each component level, pay attention to every detail of both discharge circuit inductance, capacitance control, improve and enhance the stability and lifetime of the electrical circuit, so that the initial and long-term machine use Costs by ensuring 4. AW5S Heavy load test Pitch correction with laser (300KG LOAD) heavy load test 300KG Accuracy under 1.5μ 5. Cooler Improvement description: HABOR cooler Habor panel Screen can display alarm Request HABOR Company to change Cooler function: 1. Increase the flow of abnormal auto-alarm, Wait flow is back to normal, cooler will automatically resume operation 2. Alarm message is connect to the controller screen;automatically remind users cooler Abnormal,Prevent cooler overload and user not find it Can avoided due to temperature difference between the template and have Cutting precision problem
6. Electrode cable Improvement description: 7. 1. The quality of high frequency power cable (electrode power cable) determines the service life and stability of machine. Under the consideration of both quality and engineering, AMS exclusively develops the extremely high frequency power cable (electrode power cable), which extends the service life of machine and consequently save your money. The processing speed and stability will also satisfy you.! 2. Tank design is no cable interference problem,the appearance good looking Main conductive parts are designed to behind of the tank,not easy to generate cutting speed attenuation and electrode wire aging problem 7. Waste-wire Box Improvement description: 1.Waste-wire box by the acrylic material into FRP material Description: Waste-wire box is not easy breaking into the fiber material, beautiful appearance and practical 3. Catchment tray drainage pipe has been canceled can avoid the interference problems
8. 8. Sealing ealing-board increase a Filter Device: Sealing -board additional filters to ensure that water is absolutely clean sealing-board not easy to lead to iron filings scratch sealing-board 9. New water tank: 1. Change submerge motor and dirty motor moved to the bottom of water tank, can be avoid pumped empty-run by air problem 2. Internal water recycing system uses high efficiency revolving, Filling water use to add clean water to ensure that the template processing stability and long-term problems to avoid rust.
10. 10. Interference-free design for Low- arm : Improved telescopic cover more long-term life 1. Improved telescopic cover for non-deformation and damage; to ensure long-term life 2. Y axis does not moving interference; ensure long-term accuracy 11. 11. Interference-free design for Sealing-board 1. Enclosed low-arm designed to improve machining accuracy can avoid the rear gasket leakage due to wear and tear, with sealing a bilateral fixed design; ensure long-term precision and to solve problem of water leakage
12. 12. Support USB Flash drive system in the DOS mode, Plug and Play Matching more convenient easy to use USB Flash Disk 13. 13. LED Work Lamp: Match LED work lamp, with high efficiency, long life, non-heat, high - Brightness 14. 14. 1 to 5 PASS cutting database to establish: Can be targeted Processing type Select speed mode Or precision mode,and other six kinds of punch or a die mode machining,and can be used default database or user database;more easy to establishment your own processing database,can significantly reduce the value of the interdependence of human experience,,to help quickly train the worker to enter the factory production line
15. Mechanical and electrical integration, connecting cable and pipeline are very simplified The pipeline design is not only a very simplified installation of the machine, move the machine faster and more convenient, And does not occupy valuable space inside the factory, Let factory aisle planning is more beautiful, convenient 16. 16. A complete Europe CE Certification Certificate Number: 245071008 Complete European CE certification, to ensure that the various machine parts and components in the electromagnetic interference and security protection on the guarantee of quality
17. 17. Can be corrected lower machine head design 18. Lower machine head can be calibrated against the verticality, to ensure that all important components without machining error 18. Automatically supply oil system, controlled by the screen 19. In the controller can be set up an automatic device to the oil-working hours to ensure the long-term lubrication of linear-guide 19. NEW Remote box designed New remote control box. has better stability and use life
20. 20. Water level adjustment function to increase scale identification 21. match the thickness of workpiece can be more convenient to set overflow height 21. AWT System with All New Servo Control Module The brand-new designed servo-control module, automatic wire-threading and wire-cutting procedure, allows you to monitor each operation through the monitor screen and record the operating time. Operator can easily learn how to operate the machine in no time through the more user friendly parameter adjustment interface. Extremely simplified component design with reliable tension movement unit satisfies the user with the feature of easy maintenance. In the process flow of handling failed wire-threading, with the GENTEC controller, system will automatically recycle the wire and execute the wire-threading process by the servo-control module with extremely low tension mobility rate. No matter the-wire threading is done on the broken point or in the water, the system can guarantee the user to restore the process in the shortest time and significantly improve the reliability of wire-cutting process Monitor screen: You can record every action and increase Operation of AWT stability.
22. Convenient HMI interface The main user interface is located above the work tank,match human body optimal operating height The panels can be rotated so that the operator standing at front of the machine, without moving feet can get all the machine information,space-saving design also allow the factory aisle planning more smoothly 23. More stable control of conductivity Directly on the screen display of water resistance. and can be set directly on the screen